Home

Mobotix M15D-SEC - Network Webcams

1. computer monitor then turn and tilt the cam 6 era until you have found the best position and sharpness Retighten the screws of the VarioFlex mount to prevent the position of the camera from changing 4 Ifrequired clean the lens using a clean lint free cotton cloth Correcting The Image Horizon For L12 Sensor Module Only The M15 Sec with hemispheric L12 sensor module allows the correction of an uneven image horizon via OnScreen Control that was possibly caused by the installation position The image horizon is turned by up 30 degrees clockwise or counterclockwise and can be optically restraightened by clicking the icons see image Admin Menu Setup Menu Arm Record Audio on MxPEG on 1 2 MxPEG off je l ucevent PIT EIE Bli w P OOS P Play MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Adjusting Camera Lens Focus And Installing A Filter 109 144 3 3 2 Adjusting Lens Focus L76 L160 Only for proper image sharpness and manually adjusted if required To do so use the blue Once the camera has been installed the L76 and L160 sensor modules should be checked 3 7 lens wrench and the black module wrench both are supplied with the M15 basic module The focusing aid provides a visual aid when correcting the image sharpness see 7he Live Screen of the MOBOTIX Camera in the camera s online help P
2. Www mmm mr MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 64 144 M15 Camera Manual Installation 6 Connect the sensor module cable to the sensor module Guide the cable through the opening in the front element and firmly push the sensor module cable into the connector Apply bayonet catch as shown and turn it clockwise until it gently snaps shut 7 Insert the sensor module Make sure that the MOBOTIX lettering on the sensor module is at the 9 o clock position as shown in the figure Using the black module wrench turn the sensor module clockwise until it stops 8 Insert the security clips To protect the modules against unwanted rotation insert the two red secu rity clips at the insides of the sensor modules as shown in the figure Make sure that the security clips click into place as shown in the image detail 9 Close camera housing Close the camera housing as described in Section 2 2 8 2 2 5 Replacing the Ethernet Patch Cable If you want to replace the pre installed MOBOTIX patch cable 0 5 m 20 in by a longer one make sure that you only use genuine MOBOTIX cables see Section 1 4 4 Ethernet Patch Cable For Bayonet Catch Procedure l Opencamera housing Open the camera housing as described in Section 2 2 2 2 Remove the patch cable Turn the bayonet catch of the patch cable at the inner housing cover red circle in figure coun
3. MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com UPS units not only pro tect the camera against power failures they also protect all other con nected network devices against damage from voltage peaks and lows MX Patch Box 6 9 ur T 58 144 M15 Camera Manual Installation 2 1 5 Wiring Fire Prevention Lightning And Surge Protection When installing the wiring inside or outside of buildings make sure you always adhere to the relevant regulations on wiring fire prevention and protection against lightning MOBOTIX cameras are protected against the effects of small electrical surges by a range of measures These measures however cannot prevent the camera from being damaged when stronger electrical surges occur Particular care should be taken when installing the camera outside to ensure proper protection against lightning as this also protects the building and the entire network infrastructure MOBOTIX recommends having MOBOTIX cameras installed only by certified specialists accustomed to installing network devices and having proper respect for the applicable regulations regarding lightning protection and fire prevention as well as the current tech nology for preventing damages from electrical surges Wiring When installing the wiring make sure to follow these guidelines e Data cable Make sure you only use double shielded Cat 5 or higher cable S STP for Et
4. Name Source Model Version e mx10 3 30 151 10 3 30 151 2 23 13 mx10 8 52 239 10 8 52 239 M24M Secure MX V4 0 4 18 mx10 8 85 61 10 8 85 61 Q24M Secure MX V4 0 6 9 Status of the video sources 9 Unknown Found 3 Reachable Authentication required Privacy mode Invalid network Error a be epee ers Dp x MxEasy also automatically monitors and displays the operating status of all cameras Cameras that are not on the same subnet as the computer will get a differently colored symbol than the cameras that are on the same subnet Likewise the cameras that have an unknown password or for which no user name password combination has been specified in MxEasy will be displayed in a different color The following section contains information for cameras with the status Invalid network for example for all new MOBOTIX cameras with factory settings and includes tips for configuring the cameras for the right subnet MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Download MxEasy for free from www mobotix corm 104 144 M15 Camera Manual Operating The Camera Bonjour automatic recognition of network services in IP networks Reconfiguring Network Addresses Of Cameras Using Bonjour MxEasy not only finds cameras on the same network as your computer it also finds MOBOTIX cameras located in other subnets status Invalid
5. Det pinea Hate tor User Aqew ui Masc anc Ota i rage hes t he Lice page Opere Cet awe o moda cl Lhe onga f yox Select ActivwiC De COMPO ai Kso De Lees 10 play event mages or Pe Dier Page Retesh Rate Renier page ond rie to prevert fe bowser bert towing Cow Paven Voce oF 8 Preview Mode Dipin only sw aget se X 4 x tete X Oe You will find more information and details on vPTZ in the Camera Software Manual Part 2in Section 4 3 6 Virtual PTZ the MxEasy manual in Section 2 4 1 Activating The PTZ Features and the MxControlCenter manual in Section 2 4 6 Using The vPTZ Features and Section 3 1 4 PTZ Controls In The Sidebar Panel Current versions of all manuals can be downloaded anytime from the MOBOTIX website www mobotix com under Support gt Manuals MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Virtual PTZ And Full Image Recording 3 144 3 4 2 Full Image Recording It is possible to record a full image regardless of the live image stream that is being displayed This ensures that the recording always contains the full image of the lens used even though the operator may have used the vPTZ features to zoom into the image in order to examine a specific detail 0 2 l 9 y gt Su EI TT NNI Stored full image Analysis in the stored full image This means that you can use the vPTZ feature
6. MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 764 144 M15 Camera Manual Installation 2 4 Mounting The Camera With Ceiling Mount The M15 is an allround camera designed for use in indoor and outdoor applications The camera is always installed together with the VarioFlex mount which is shipped as a wall mount but can be converted to a ceiling mount in just a few steps The best camera position for the selected lens must be found before installing the camera on a ceiling an overhang or balcony see Section 2 1 1 Installation Options Wall Ceiling Pole and Section 2 1 2 Installing The Camera With Hemispheric Sensor Modules You can fine tune its position once the camera has been installed on the ceiling 2 4 1 VarioFlex Ceiling Mount Using the VarioFlex ceiling mount the camera can be precisely panned both horizontally and vertically to suit the area that is to be monitored When installed on a ceiling the camera can be turned or tilted as follows e horizontally 360 e vertically 107 Tilting the camera when s installed on a ceiling 7 Horizontal 360 ra Vertical 107 ae MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Mounting The Camera With Ceiling Mount 5 144 In addition a cavity or in wall socket can be installed for the network cable protruding
7. side can be used to adapt it open lock click subview adapt view click next subview adapt view and close lock again Camera Images And Subviews Of Camera Images The MI5D s ability to operate multiple sensor modules means that in double image display the live image s camera images left right can be used for differing display modes Depending on the display mode selected for each camera image this may be divided into subviews Four subviews subview 1 highlighted yellow frame Left camera image with three subviews Right side camera image with a partial view Panorama Focus display mode Full image display mode for example Cam sensor module for example Cam2 sensor module When you click inside one of the subviews this area is highlighted with a yellow frame All of the PTZ actions triggered by the mouse joystick or OnScreen Control now only apply to the highlighted subview MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Virtual PTZ And Full Image Recording 123 144 Sensor Configuration Only with Two Sensor Modules Sensor configuration specifies which sensor module is connected to which of the camera s connections Cam or Cam2 and in which camera image left right the sensor module is to appear for the dual image display Open the corresponding dialog box here Admin Menu Sensor Configuration 1 gt MOBOTIX S14 S14D Image Sensor Configurat
8. 134 144 M15 Camera Manual Operating The Camera Blind module The microphone can be irreversibly deactivated 3 7 Additional Notes 3 7 1 Operation with Only One Sensor Module If the MOBOTIX M15 is used with only one sensor module the blind module needs to be installed item 1 4 in Section 1 3 Delivered Parts and Dimensions If this is not the case the camera must not be used see Section 2 2 1 Initial Installation of the Sensor Modules 3 7 2 Password For The Admin Menu Accessing the Admin Menu of the camera the Admin Menu softbutton is only possible after entering a user name and password e Factory default user name is admin e Factory default password is meinsm The Quick Installation assistant automatically appears when the Admin Menu is accessed for the first time It provides an easy method to adjust the basic camera settings to the current application scenario For security reasons we highly recommend changing the default administrator password after the camera has been properly configured Enter the user name and password exactly as shown above Note that all entries are case sensitive Make sure that you store information on user names and passwords in a secure place If you lose the administrator password and cannot access the administration menu the password can only be reset at the factory This service is subject to a fee 3 7 3 Permanently Deactivating The Microphone Deactivatin
9. M15 Camera Manual The HiRes Video Company MO BOTIX HiRes 6 Megapixels 4096 x 1536 Software zoom Skyline Format free Each image format freely definable 30 Frames s VGA 640 x 480 30 F s Mega Virtual PTZ Digital pan tilt zoom Backlight Safe using CMOS without mechanical iris Internal DVR Internal via Flash external via Network Win Lin Mac Recording via Network on PC up to 4 Terabyte Microphone amp speaker Audio bi directional via IP variable framerates SIP Client with video IP Telephony Alarm notify cam remote control Dual Modular Unique VideoMotion Multiple windows True to the original The weatherproof robust successor to our successful MOBOTIX dual camera fA Precision pixel based features interchangeable sensor modules as well as the latest MOBOTIX system technology As a result it remains totally unique in terms of performance functionality and design 22 to 140 F Weatherproof 30 to 60 C IP66 no heating necessary IEEE 802 3af PoE Network power even in winter 60 184 EN V2 07 2013 HiRes Video Innovations Robust No moving parts The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its hes fes hous decentralized concept has made high resolution video systems cost efficient MxCC MxEasy Licence free Video Management Software MOBOTIX AG gt D 67722 Langmeil Tel 49 63
10. Tilting the camera when ee 1 MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Mounting The Camera With Wall Mount In order to ensure a flush finish with the surface connect the camera patch cable to the network cable using a standard adapter that is protected in the wall mount or a MX Patch Box that can easily be inserted into the cavity socket of the wall mount VarioFlex mount For more information on the MX Patch Box please visit www mobotix comand go the Products lt Accessories Interface Boxes section It is also possible to install an in wall socket with 45 connector When doing so make sure that the in wall socket is placed as high up in the wall mount housing as possible When installing on wall cabling breaking out one ofthe four possible openings in the base of the wall mount with a pliers will ensure that the cables can be fed neatly into the camera The connection to ihe camera patch cable can be established using a suitable adapter within the wall mount Caution If using the camera outdoors only use the opening at the bottom of the mount fo prevent water from entering the mount MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com salesemobotix com 6 MX Patch Box in the wall mount Pliers to break through a cable guide 72 144 M15 Camera Manual Installation Procedure 1 Install and pr
11. www mobotix com sales mobotix com 66 144 M15 Camera Manual Installation Only use USB cables with angled plugs inside the housing of the M15 2 2 6 Connecting a USB Cable Using the USB plug you can attach existing expansion modules such as the MOBOTIX ExtlO USB the MX 232 IO Box or external USB hard drives to the camera in a weather proof and well protected manner Procedure 1 Open camera housing Open the camera housing as described in Section 2 2 2 Remove the single wire plug Remove the blue single wire plug red circle in figure Guide the USB cable through the housing Guide the cable from the front through the cable guide in the hinge of the VarioFlex mount see figure a Connect the USB cable Insert the MiniUSB plug into the appropriate connector Apply bayonet catch as shown and turn it clockwise until it gently snaps shut Close camera housing Close the camera housing as described in Section 2 2 8 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com First Installation Steps 67 144 2 2 7 Connecting a Two Wire MxBus Cable You can use such a cable to connect additional MOBOTIX modules e g the MX GPS Box or the MX 232 IO Box to the M15 Note that you can attach two MxBus cables each having two wires to the MxBus connector red circle in figure Take care not to switch the polarity of the wires It is recomm
12. 44 M15 Camera Manual Installation Procedure l Prepare the sensor module Remove the plastic 1 E lock nut this is not needed any more Remove the bayonet catch by rotating it counter clockwise then remove the blue rubber plug l 2 Remove the transport plugs Gently pull the two transport plugs out of the sensor module sockets by lifting the rim of the plugs Now pull the connectors of the sensor module cables out of the back of the transport plugs take care not to damage the con nectors or the cables Make sure that you do not pull the sensor module cables out of the housing 3 Connect sensor module cable Firmly push the sensor module cable into the module s connector as shown in the figure 4 Lock sensor module cable Apply bayonet catch as shown and turn it clockwise until it gently snaps shut 5 Insert the sensor module Make sure that the MOBOTIX lettering on the sensor module is at the 9 o clock position as shown in the figure MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com First Installation Steps 6 144 6 Lock the sensor module Using the black module wrench turn the sensor module clockwise until it stops Repeat steps 3 to 6 for the second sensor module or the blind module respectively Installing the blind module is a mandatory prerequisite when using the M15 as a mono camera with only one sensor mo
13. The camera is always installed together with the VarioFlex Q Q mount which is shipped as a wall mount and can also be installed directly on the pole mount The best camera position for the selected sensor module must be found before installing the camera see Section 1 2 1 You can fine tune its position once the camera has been installed on the wall MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Mounting The Camera With Pole Mount Accessories 2 5 1 Pole Mount MX MH SecureFlex ESWS When mounted to a pole the camera can be turned or tilted similar to wall installations e horizontally 180 e vertically 80 Ifthe wall mount is rotated by 90 degrees you can also point the camera all the way down 1 Pole Mount Dimensions E Height 174 mm 6 85 in m Width 140 mm 5 51 in Depth 45 mm 1 77 in MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 80 44 M15 Camera Manual Installation Scope Of Delivery And Required Parts Please first check that all the components supplied with the corner and pole mount set are present in the original packaging Item Number Part Name 5 Pole mount 5 2 4 Stainless steel hex head screws M6x20 mm 5 3 4 Stainless steel hex head screws M6x35 mm not required 5 4 8 Stainless steel w
14. as desired The example here shows an overview panorama of the entire room as well as the entrance which would have otherwise no longer been visible in the panorama Original Vollbild Surround View Quad View The M15 s Surround display mode delivers four different directions at a glance Each of the four views features a software controlled pan tilt zoom function virtual PTZ allowing it be customized as necessary In order to facilitate camera operation the M15 can store a total of 256 user defined camera views in addition to the preset standard views Full Image And Normal View In addition to the Panorama Double Panorama Panorama Focus and Surround views the MI5 image may be displayed on a monitor as the original fisheye version Full Image display mode or as the camera corrected image section Normal display mode Switching to one of the other display modes described is possible at any time MOBOTIX AG Security Vision Systems Made in Germany www mobotix com salesemobotix com 18 144 M15 Camera Manual Product Overview 1 1 3 Advantages And New Features The high resolution M15 AllroundDual is the more powerful successor to the M12 and features a new modular system design and five megapixel image sensors Although the maximum size at which the images of an M15 sensor can be displayed is 3 1 megapixels live or recorded the M15 outperforms the previous M12 model and other dual cam
15. completely A MOBOTIX interface box can be integrated in the wall mount Make sure that you have found the best camera position before installing the camera It is important that the camera s field of view is not obstructed in any way Once the camera has been installed on a wall or ceiling you can fine tune its position If the monitored area changes or the camera has to be installed in a different location it is easy to exchange the camera s sensor modules and continue using the camera without having to upgrade to new video software MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Tilting the camera when installed on a wall Horizontal 180 Vertical 60 to 20 Tilting the camera when installed on a ceiling Horizontal 360 Vertical 90 to 7 VarioFlex wall mount with protected cabling and cover for in wall sockets and MOBOTIX interface boxes 52 144 M15 Camera Manual Installation Wall installation Horizontal 180 Vertical 60 to 20 Wall Installation The M15 can be installed on the wall of a building or structures even mobile surfaces for both indoor and outdoor use The camera is mounted using the pre installed VarioFlex mount supplied as standard which is easily secured using the four enclosed screws and screw anchors depending on the surface it can also be mounted without screw anchors directly over the in wall socket
16. from the ceiling which allows sufficient space to use a standard adapter to connect the network cable with the camera patch cable Ww Standard adapter for cable connection Additional sealing of the wall mount with silicone on the wall seal is recommended for use with uneven surfaces When installing on wall cabling breaking out one of Pliers to break through the four provided openings in the base of the ceiling a cable guide mount will ensure that the cables can be fed neatly into the camera The camera patch cable must be connected with the network cable using a suitably sealed adapter MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 76 144 M15 Camera Manual Installation No screw anchors are required for wooden surfaces Additional sealing pos sible for example with shrink tubing Procedure 1 Connect the cable Connect camera patch cable Convert to a ceiling mount Simply remove the lock screw on the central joint and exchange the wall mount for the supplied ceiling mount Before fastening the ceil ing mount to the central joint Using the screw of the wall mount the patch cable is guided through one of the four openings 9 7 Install and prepare the network connection Guide the pre installed camera patch cable through one of the four openings in the ceiling mount this will be connected later with the network cable using a sui
17. 39 image angle horizontal e L76 Telephoto with 27 image angle horizontal e 160 Telephoto with 13 image angle horizontal The integrated virtual PTZ features of the camera software or MxControlCenter MxEasy properly correct the lens distortion in the L12 Fisheye that is specific to each lens The L25 Super Wide Angle lens has very little distortion and delivers good image quality even when the maximum digital zoom is used If the M15 is installed in the corner of a room with this lens almost the complete room will be visible on the image MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Technical Specifications 2 5 144 Mu L76 M15D sensor modules can ensor Lenses be freely interchanged Original image a 35 mm equivalent 12 mm 25 mm 38 mm 5 mm 76mm 160mm noo orovide Nominal focal length 1 8 mm 4 mm 6 mm 8 mm 12 mm 25 mm a non reflective pro Aperture 2 0 2 0 2 0 2 0 2 0 2 5 E b nca mage 180 82 55 40 27 13 Vertical image angle 160 61 41 30 20 10 At 1 m distance Image width infinite 1 7 1 0 0 7 0 5 0 2 Image height n 12 0 7 0 5 0 4 0 2 At 5 m distance Image width infinite 8 7 5 2 3 6 24 1 1 Image height 55 5 9 3 7 2 7 1 8 0 9 At 10 m distance Image width infinite 17 4 10 3 7 2 4 9 2 3 Image height 110 11 9 75 5 4 3 6 1 7 At 20 m distance
18. Langmeil Germany Information subject to change without notice MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Contents CONTENTS 1 Product Overview 10 11 M15 AllroundDual 10 1 1 1 General Product Characteristics 10 112 Hemispheric Sensor Module 15 1 1 3 Advantages And New Features 18 114 Decentralized Video System 20 1 1 5 Green IP Video 22 12 Technical Specifications 24 12 1 M15 Lens Options 24 12 2 Camera Variants Lenses Hardware Image Formats 26 12 3 Camera Variants Software Features 27 12 4 Technical Data 28 1 3 Delivered Parts and Dimensions 30 1 3 1 M15 Core Basic Module 30 13 2 L12 Sensor Module 36 1 3 3 L25 L51 Sensor Modules 38 1 3 4 L38 L76 L160 Sensor Modules 40 14 Available Accessories 42 1 4 1 Polarization Filter 42 1 4 2 MiniUSB Cable to MiniUSB Straight Angled 42 1 4 3 MIiniUSB Cable To USB A Socket 42 14 4 Ethernet Patch Cable For Bayonet Catch 42 1 4 5 NPA PoE Set 43 1 4 6 MX Patch Box 43 1 4 7 MX NPA Box 43 1 4 8 MX GPS Box 44 1 4 9 MX 232 IO Box 44 1 4 10 ExtlO Expansion Module 44 1 4 1 Mx2wire Media Converter 45 1 4 12 Other Accessories 45 15 MOBOTIX Software 46 15 1 Integrated Camera Software Firmware 46 15 2 MwxControlCenter 47 15 3 MxEasy 48 1 5 4 MOBOTIX App 49 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 3 144 4 144 M15 Camera Manual Contents 2 1 2 1
19. Other Accessories Since the range of accessories for the MOBOTIX system keeps growing you should visit the MOBOTIX website www mobotix com in the Products gt Accessories section to see the entire list of available accessories THE MOBOTIX INFORMATION CHANNELS Support on the MOBOTIX Website MOBOTIX http www mobotix com other Support The MOBOTIX Video Tutorials A http www mobotix com other Support am mcm Tutorials Seminars on MOBOTIX Campus http www mobotix ecampus com Y The MOBOTIX YouTube Channel Ou u 0 http www 6 com MOBOTIXAG MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 46 144 M15 Camera Manual Product Overview Download free of charge from www mobotix com No license fees Free updates 1 55 MOBOTIX Software 1 5 1 Integrated Camera Software Firmware MOBOTIX cameras and connected MxBus modules operate with built in firmware whose functions are accessed by the MOBOTIX remote stations MxControlCenter MxEasy and MOBOTIX App The M15 models therefore also feature a variety of functions that are integrated in the firmware from motion detection and long term storage right through to alarm notification via video IP telephony The virtual PTZ functions allow you to continuously zoom into or out of a MOBOTIX camera image using either the mouse wheel or a joystick When recording image or video sequences you can choos
20. RS232 connector Can be used with MX 232 IO Box via USB MOBOTIX accessories Sub D HD 15 M12 discontinued Shock detector Reports acts of vandalism etc to the M15 camera housing MxActivitySensor Detects movements of people objects and the directions of movement Outside temperature sensor Edid into the front element of the M15 Core mod ule Mobile video remote station M15 operation is integrated in the MOBOTIX App for iOS devices MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 20 144 M15 Camera Manual Product Overview 11 4 Decentralized Video System Usually cameras only supply images while processing and recording take place later on a central PC using video management software This centralized structure has too many limitations for high resolution video systems since it requires high network bandwidth and the PC processing power is insufficient when using several high resolution cameras Due to the large number of computers and servers required traditional centralized systems are therefore becoming less suitable and cost effective As part of the decentralized MOBOTIX concept every camera features a high speed processor and ifnecessary digital long term flash memory MicroSD card can be integrated to provide several days of recording time The com 4 puter or video control center is CMOS CPU MicroSD required only to view and control 5 mega
21. Section 2 3 Mounting The Camera With Wall Mount and the following sections while the drilling templates are included at the end of the manual 2 1 Preparing The Installation Before installing the MOBOTIX M15 the following questions should be answered l Where will the camera be installed 2 What other additional installation options are available 3 How is the camera connected to the network and how is the power supplied 4 How are the connections furnished from the building 5 What cabling considerations are necessary The following sections in this chapter should answer all these questions If anything is unclear or you have more questions please contact your MOBOTIX partner or MOBOTIX Support directly Contact information can be found at www mobotix com under Support 2 1 1 Installation Options Wall Ceiling Pole Like all MOBOTIX cameras the M15 is extremely flexible in terms of how and where it can be installed An M15 can be used for both indoor and outdoor applications in fixed or mobile applications constantly changing locations or in on vehicles of any kind The M15 cameras have been certified weatherproof according to IP66 IP66 and can work reliably in temperature ranges from 30 C to 60 C 22 F to 140 F without heating or a fan A practical weather and sun protective cover is integrated into the extremely resistant housing which is made of UV resistant special purpose plastic Thanks to the camera s un
22. Thus you can set up and operate the MOBOTIX camera using a JavaScript enabled browser on all common operating systems such as Windows Linux Apple etc As an alternative you can also use the MOBOTIX applications MxControlCenter and MxEasy Follow these steps to set up the camera 1 Connect the camera to the network Power is supplied directly via the Ethernet cable see Section 2 7 Network And Power Connection 2 Set up the camera s network parameters Manually using a web browser see Section 3 2 1 Manually Setting Up The Network Parameters In A Browser and below Automatically using MxControlCenter MxEasy see Section 3 2 3 and Section 3 2 4 or via DHCP see Section 3 2 6 Starting The Camera With An Automatic IP Address DHCP 3 Configure the camera using the web based user interface MxControlCenter or MxEasy Every MOBOTIX camera comes preconfigured with a static IP address in the 10 x x x range forexample 10 8 0 99 However local computer networks usually have IP addresses inthe 172 or 192 ranges In order access a MOBOTIX camera via the network the camera needs to obtain an IP address in the same address range You can set up the network parameters of the MOBOTIX camera using one of the following methods Manually using MxCC and MxEasy or by DHCP MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Manual and Automatic Operation Over
23. X Web functionality FTP email X Playback Quad and MultiView bidirectional X sound in browser Logo generator animated X Flexible event logic X Master Slave arming X Several scheduled privacy zones X Customized voice messages X VoIP telephony audio video alert X Remote alarm notification network msg X Signal inputs outputs RS232 Via MX 232 IO Box Programming interface HTTP API X Security features HTTPS SSL IP based access X control IEEE 802 1X network authentication Video Motion detector X MxAnalytics MxActivitySensor X MxEasy MxControlCenter X EU MOBOTIX App X M E E MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 Camera Manual Product Overview 28 144 1 2 4 Technical Data Technical Data M15 Model variants MX M15M SEC Day or Night sensor module MX MI5D SEC any combination of Day Night sensor modules Lens Options 12 to 160 mm compared to 35 mm camera horizontal angle 180 to 13 Sensitivity Color sensor 0 25 lux at 1 60 s 0 013 lux at 1 s Black and white sensor 0 05 lux at 1 60 s 0 0025 lux at 1s Image sensor per sensor module 1 2 5 CMOS 5 MP 2592x1944 pixels progressive scan Max image resolution with one sensor module Color 2048x1536 3MEGA Black and white 2048x1536 3MEGA Max image resolution with two sensor modules dual image Color 4096x1536 6MEGA Black and white 4096x1536
24. avail able in the current subnet of the computer If you do not have permission to modify these settings on your computer contact your system administrator for assistance MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com First Images And The Most Important Settings 99 144 MOBOTIX Searching And Displaying Cameras Launch MxControlCenter after successful installation by double clicking the shortcut that was created by the installer or the executable file MxCC exe in the installation directory on your computer The Add Video Sources dialog box appears and the application automatically searches for MOBOTIX cameras in the local network when you launch the program for the first time Select Video Source gt Add from the menu to perform a camera search at a later time If your MOBOTIX camera is properly connected it should appear together with the exist ing video sources in the following list Add Video Sources Name IP Address Path Type Version Status sS O TET 10 8 85 61 Q24M Secure MX 4 0 6 9 Bonjour CancelSearch 9 10 8 52 239 10 8 52 239 M24M Secure MX 4 0 4 18 Bonjour 2 j j o 10 3 30 151 012D Sec MX 3 2 23 03 Bonjour Insert manualy D Different subnet 2 video sources found 1 selected ri rnc ncn ce List of video sources Legend Camera preview Video sources in this context not only refer to MOBOTIX cameras but also to third
25. camera During installation ensure that the camera is focused on the most important areas of the room as directly as possible in order to optimize image quality and provide the desired level of detail recognition This applies above all to wall and ceiling installations that must be carried out at greater heights for technical or other reasons over doors windows etc The lens capabilities can be only fully utilized by tilting the camera appropriately MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 54 144 M15 Camera Manual Installation 2 50 m 3 50 m 1 50 m MOBOTIX recom mendation MOBOTIX original 180 Panorama image L12 sensor module 2 50 m 3 50 m Allround View A single M15 sensor module can moni tor an entire room right into each of the four corners 360 Panorama View thanks to its hemispheric lens The camera should ideally be positioned on the ceiling in the center ofthe room Rooms with a square floor area of up Capture of ena to approx 40 m2 generally allow the recognition of detail even at the bor ders of the full image Rooms with up to 100 m of floor area can be monitored using one single camera if you only The image quality precision diminishes as the want to monitor specific objects or to distance of an object to the camera focus point know if persons enter a room increases 1 very good 2 goo
26. damaged when removing the inner lid The MicroSD card is located at the top in the center of the circuit board Make sure not to touch the circuit board when replacing the MicroSD card MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 84 144 M15 Camera Manual Installation 5 10 T Unlock MicroSD card Carefully slide the metal latch to the right using your fingernail Remove the MicroSD card Lift the metal latch upwards and to the right and remove the SD card Insert and lock the MicroSD card Insert the MicroSD card and close the metal latch Gently slide the metal latch using your fingernail back to the left to lock the MicroSD card Attach inner cover Attach inner cover tighten Allen screws and replace the connection cables Close camera housing Close the camera housing as described in Section 2 2 8 then reconnect the power supply Activate recording If you have inserted a MicroSD card that has already been MxFFS formatted you can activate recording under Admin Menu Storage on External File Server Flash Device Once the camera has been rebooted it automati cally activates recording Format MicroSD card f a new MicroSD card is used it must be formatted before use as described in Section 3 5 2 Formatting The MicroSD Card MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix co
27. factory pre installed cable of the camera to a PoE port of the PoE switch router The switch router must support the PoE standards IEEE 802 3af or IEEE 802 3at PC 10 8 0 11 255 0 0 0 PoE PoE switch router LAN www Q Q Kamera 10 8 0 99 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com IP addresses in the diagram are shown only as an example The PoE adapter replaces the crossover cable when directly connect ing To a computer For the M15 you should use the blue MX NPA PoE Set or the MX NPA Box previous MOBOTIX network power acces Sories such as the NPA Set Power Box and Power Rack MX NPA Set MX NPR 4 and MX NPR8 20 are not suitable for use with the M15 0 IP addresses in the diagram are shown only as an example 88 144 M15 Camera Manual Installation Variable PoE Multiple cameras can be operated simultaneously from the same switch 2 7 5 Variable PoE The power consumption of the camera depends on the functions in use as well as any peripheral devices connected see table PoE classes 1 2 or 3 may be selected in the browser based user interface in order to optimally adjust the camera to your system design PoE switch in use emergency power concept etc PoE Power Level Classes IEEE 802 3af standard Max power consumption 0 44 W 3 84 W Camera operating mode and p
28. for smaller installations or the weatherproof PoE injector MX NPA Box MX OPT NPAT EXT may be used in outdoor scenarios For larger installa tions we recommend investing in a PoE capable supply device available on the market Sections 2 8 and below contain more information on the possible combinations of connecting the M15 and power supply options PoE adapter MX NPA PoE Comera The maximum length of the network cable for power supply over an Ethernet cable is 100 m The Mx2wire media converter set available as an accessory can be used to extend the range of an Ethernet connection up to 500 m in length maximum transmission speed for a 500 m cable 45 Mbps and 12 W for the PoE device The MOBOTIX M15 can be powered by switches or routers that support the PoE Power over Ethernet standard and conform to IEEE 802 3af Advantages of PoE power supply e Centralized backup power supply available via network Lower more cost effective power consumption e Camera does not require an additional network connection MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Preparing The Installation 57 144 Using Uninterruptible Power Supplies UPS You should install an uninterruptible power supply UPS in order to maintain a continuous power supply even when utility power fails These devices also provide full protection against electrical surges and voltage fluctuations enh
29. housing at the spots indicated by the red arrows 5 Using the supplied 5 mm Allen wrench tighten ki the two bolts at the back of the camera housing Push the two rubber plugs back into the opening Ca of the screws to prevent humidity and dirt from 5 entering the camera Do not forget to apply rubber plugs at the back of the housing MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 700 44 M15 Camera Manual Installation 2 3 Mounting The Camera With Wall Mount The M15 is an allround camera designed for use in indoor and outdoor applications The camera must always be installed with the VarioFlex mount which has been prepared at the factory for wall mounting and allows the cabling to be concealed The best camera position for the selected lens must be found before installing the camera on the wall see Section 2 1 1 Installation Options Wall Ceiling Pole and Section 2 1 2 Installing The Camera With Hemispheric Sensor Modules You can fine tune its position once the camera has been installed on the wall 2 3 1 VarioFlex Wall Mount Using the VarioFlex wall mount the camera can be precisely panned both horizontally and vertically to suit the area that is to be monitored When installed on a wall the camera can be turned or tilted as follows e horizontally 180 e vertically 80 installed on a wall ae Horizontal 180 d Vertical 80 QT
30. image To store the changed sensor configuration in the camera proceed as described at the end of Section 3 4 3 Special M15 Configuration In The Browser Configuration Of The M15 Basic Parameters for Hemispheric Sensor Modules Thanks to its hemispherical lens the MOBOTIX M15 provides certain special configuration options for the image settings Depending on where the camera is installed ceiling wall or floor and on the live image display preferred by the user certain important basic settings and if necessary their adjustment must be configured when a MI5 is first installed MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 116 144 M15 Camera Manual Operating The Camera o a Left and right camera images from two sensor modules M15D Complete the steps described below in the browser window Log the camera on and boot it as described in Section 3 2 First Images And The Most Important Settings Depending on the number of sensor modules used proceed as follows One sensor module Proceed with step 2 Two sensor modules In this case the remaining steps need to be executed separately for each sensor module Specify each sensor module s installation position separately in the Installation right and Installation left Quick Control fields for the right and left sensor module i e camera image respectively If you need to use the OnScreen Control
31. or extracts of sequences you can export the required data to any PC or USB hard drive MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 13 144 14 144 M15 Camera Manual Product Overview Low Power Consumption In Accordance With The PoE Standard IEEE 802 3af A M15 uses no more power than its predecessor typically 4 5 watts despite the new sensor technology Adjusting the PoE class via the camera software also enables the use of PoE switches that cannot be operated on all ports with PoE class 3 up to max 12 95 V Model Variants The dual camera M15 Core basic model is available as an SEC or IT variant each of which has different functions as well as one or two sensor modules Each variant features an internal long term memory a pre formatted and pre installed 4 GB MicroSD card There is also a MI5M Core Web basic module available which is a cost efficient weath erproof and high resolution webcam model Only one of the six day sensor modules can be used for this model Internal DVR bidirectional and other security functions not relevant for a webcam are not available The maximum resolution of each sensor module is three megapixels for the SEC and Web variants over 2 5 times larger than Full HD The IT variant is limited to HD resolution 1280x720 The sensor modules can be mounted on the basic module in just a few easy steps see Section 2 2 1 Initial Installation
32. see next section click into the correspond ing sub image when viewing a dual image or show the image of only one sen sor module 2 Select installation position wall ceiling floor Click Installation in the Quick Control panel and then select Wall Ceiling or Floor according to the installation position of the camera Ceiling always means that the orientation of the camera or sensor module is from top fo bottom and for Floor the camera or sensor module s orienta tion is from bottom to top 16 8 5 Wf a Ca Ci Anze 2 Modus Admin Menu ER __Setup Menu Ansicht laden pls festiegen E cone ae __Audioon Zoom MxPEC on MxPEC off uc event 3 LEDs __ Pay sound _ Pay Last Feel 2 j Rildprogramm Bildqualitat Helligkeit Belichtungssteuerung Farbsattiqung Gegenlichtkorrektur a Scharfe IPFC Qualirar fey Scnartsteilhilfe 4 As a result you will get a perspective corrected panorama view for each image sensor matching the specified installation position Panorama view is configured as the factory setting and it can be changed as described below Switch to the Display Mode Quick Control Setthe mode that you want to be the standard view For demonstration purposes the descriptions below describe the typical display mode for the wall mount and the ceiling moun
33. sockets in the front element are fitted with transport plugs The MOBOTIX M15 cameras are delivered with a pre assem i Wr NL Ha When operating the camera it needs to be fitted either L with sensor or blind modules This closes off the front ele ES ae J ment and protects the camera against foreign objects 125 138 L51 L76 insects and water 1160 sensor modules Only replace the sensor modules when the camera is disconnected from the power supply Make sure the power supply to the camera is disconnected before installing or replacing sensor modules When installing the sensor modules make sure that the sensor module cables and the patch cable are not damaged or bent sharply Using One or Two Sensor Modules 6 With an M15 you have the choice of using the camera with one or two sensor modules Since the modules are easily exchanged it is also possible to add a module or to use different ones later on MOBOTIX Tutorials http www mobotix com other Support Tutorials Note that you must not operate the M15 with installed transport plugs since the camera is not protected against the environments Transport plug MI5 with s transport MI5 with one transport plug M15 with one blind module Ugs iiid No operation allowed Unrestricted operation No operation allowed IP66 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 60
34. subject to special documentation or it may be prohibited All users of MOBOTIX products are therefore required to familiarize themselves with all valid regulations and comply with these laws MOBOTIX AG is not liable for any illegal use of MOBOTIX products Network Security MOBOTIX products include all of the necessary configuration options for operation in Ethernet networks in compliance with data protection laws The operator is respon sible for the data protection concept across the entire system The basic settings required to prevent misuse can be configured in the software and are password protected This prevents unauthorized parties from accessing these settings Never Remove Domes Lens Covers The MOBOTIX cameras M15D and M15M should never be operated without their preinstalled transparent domes sensor modules M15D and housing M15M or pro tective lens covers sensor modules M15D The camera is no longer weatherproof when operated without the domes or protective lens covers The exposed metal ring around the lens can become extremely hot when the exterior temperature is high Touching this ring can cause burns Only Exchange Sensor Modules When Powered Off Make sure that the camera s power supply has been disconnected before attempting to exchange any sensor modules MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Contents 7 144 CS HiRes dual image up t
35. such a case you need to remove the front element replace the sensor modules and install the front element again If no security clips have been installed you can exchange the sensor modules as described in Section 2 2 1 Initial Installation of the Sensor Modules Procedure 1 Open camera housing Open the camera housing as described in Section 2 2 2 Remove fhe security clips The sensor or blind mod ules may have been protected against unwanted rotation by applying the security clips Push the top pfthe security clip in the direction of the blue arrow see figure in the side note so that it can pass the notch and pull the clip upwards Remove the sensor module cable from the sensor or blind module The sensor module cables are secured using a special cable lock with bayonet catch To remove the bayonet catch turn it counter clockwise until it gently snaps open Take off the catch and pull out the cable Remove the sensor or blind module Set the black module wrench onto the sensor or blind module so that the two notches lock into the two holes of the module at the 12 and 6 o clock positions Turn module wrench counter clockwise by 90 degrees until it stops Push the sensor or blind module out of its socket Prepare the new sensor module Remove the plastic lock nut this is not needed any more Remove the bayonet catch by rotating it counter clockwise then remove the blue rubber plug ee e 2
36. the power supply the red LED lights up blinks 1 Start 0 8 for two seconds then stays on permanently red A camera self test is carried out at this point and the entire system is started In case of an error the camera will start using the backup operating system e Waiting for key pressed Both LEDs light up for four seconds If you press the R or 2 Key 9 e L key of the camera during this time the camera will execute the corresponding function see Section 1 2 6 Starting The Camera With The Factory IP Address and Section 1 2 7 Starting The Camera With An Automatic IP Address DHCP To do so use a paper clip but avoid using sharp or pointed objects e Ready Once the camera software has been started the green LED is on permanently 3 Ready 3J 0 and the red LED blinks The camera can now be accessed via the network browser a MxControlCenter MxEasy MOBOTIX App etc Note During the startup sequence of the camera the LEDs will always light up even if they have been deactivated in Admin Menu gt LED Setup MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 90 144 M15 Camera Manual Operating The Camera Download the free of charge MxEasy and MxControlCenter software at www mobotix com Camera software in the browser 3 OPERATING THE CAMERA 3 1 Manual and Automatic Operation Overview MOBOTIX cameras do not require any extra software
37. to edit it highlighted TIENS with a yellow frame MOBOTIX Q24 mx10 8 0 79 Live Admin Menu b Setup Menu E IT T Arm amp Record Audio on Ic MxPEC on m saco RIE LEDs Blink Camera live image with panorama correction with OnScreen Control visible 5 After you have modified the desired setting close the control panel in the top left hand corner 6 Click the lock icon again to close it lock clasp is down The panorama image setting is then locked until the camera is next restarted MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Virtual PTZ And Full Image Recording 119744 To permanently save the standard image setting defined for the M15 go to the Store Complete Configuration option in the Manage Settings Quick Control The settings will then remain in effect even after rebooting Functions Of The M15 s OnScreen Control Close Tilt up Start panning to the left Start panning to the right Tilt down Zoom Panorama correction Image tilt correction Default setting To use the OnScreen Control click the arrows in the top area for shifting the image sec tion In the bottom areas which are displayed when needed click to the left and or right of the center point The same applies to every area The further away that you click from an area s center point the greater the change triggered To re
38. with a clean soft cotton cloth for optimal image results 8 Establish a connection to the camera check the image Establish a connection to the camera as described in Section 3 7 Manual and Automatic Operation Overview and the following sections The live image from the camera should be visible on the computer monitor Check image sections on the computer monitor The VarioFlex mount and wall mount must always be used for wall installation see Section 2 3 Mounting The Camera With Wall Mount MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 78 1 44 M15 Camera Manual Installation 2 5 Mounting The Camera With Pole Mount Accessories If you are intending to install the camera on a pole you should consider using the MOBOTIX M15 pole mount This mount is made of 3 mm powder coated stainless steel white and has been designed specifically for outdoor use The supplied stainless steel straps allow the mount to be attached to poles with diameters between 60 mm and 180 mm By design the pole mount does not allow the use of an in wall socket We recommend using an MX Patch Box that can be easily inserted into the cavity socket of the wall mount VarioFlex mount in order to ensure a weatherproof connection of the network devices For more information on the MX Patch Box please visit www mobotix comand goto the Products gt Accessories gt Interface Boxes section
39. 02 9816 103 gt Fax 49 6302 9816 190 gt sales mobotix com E o o E Q o E z 5 5 2 44 M15 Camera Manual Contents THE MOBOTIX INFORMATION CHANNELS Support on the MOBOTIX Website MOBOTIX http www mobotix com other Support The MOBOTIX Video Tutorials http www mobotix com other Support Tutorials Seminars on MOBOTIX Campus http www mobotix ecampus com The MOBOTIX YouTube Channel http www youtube com MOBOTIXAG MOBOTIX Seminars MOBOTIX offers inexpensive seminars that include workshops and practical exer cises For more information visit www mobotix com gt Seminars Copyright Information Download the latest version of this manual and the MxEasy and MxControlCenter manuals as PDF files from www mobotix com Support gt Manuals All rights reserved MOBOTIX MxControlCenter amp and MxEasy are internationally protected trademarks of MOBOTIX AG Microsoft Windows and Windows Server are registered trademarks of Microsoft Corporation Apple the Apple logo Macintosh OS X iOS Bonjour the Bonjour logo the Bonjour icon iPod and iTunes are Apple Inc trademarks registered in the U S and other countries iPhone iPad iPad mini and iPod touch are Apple Inc trademarks Linuxis a trademark of Linus Torvalds All other marks and names mentioned herein may be trademarks or registered trademarks of the respective owners Copyright 1999 2013 MOBOTIX AG
40. 1 2 1 2 2 1 3 2 1 4 2 1 5 2 2 2 2 1 2 2 2 2 2 3 2 2 4 2 2 5 2 2 6 2 2 7 2 2 8 2 3 2 3 1 2 4 2 4 1 2 5 2 5 1 2 6 2 7 2 7 1 2 4 2 2 7 3 2 7 4 2 7 5 2 7 6 3 1 3 1 1 3 1 2 3 1 3 3 2 3 2 1 3 2 2 3 2 3 Installation Preparing The Installation Installation Options Wall Ceiling Pole Installing The Camera With Hemispheric Sensor Modules Network Connection And Power Supply UPS Preparing The Camera Connections Wall Outlets MX Patch Box Wiring Fire Prevention Lightning And Surge Protection First Installation Steps Initial Installation of the Sensor Modules Opening the Camera Housing Installing the Security Clips Optional Exchanging Sensor Modules Replacing the Ethernet Patch Cable Connecting a USB Cable Connecting a Two Wire MxBus Cable Closing the Camera Housing Mounting The Camera With Wall Mount VarioFlex Wall Mount Mounting The Camera With Ceiling Mount VarioFlex Ceiling Mount Mounting The Camera With Pole Mount Accessories Pole Mount MX MH SecureFlex ESWS Replacing The MicroSD Card Network And Power Connection Network Cabling For M15 With Patch Cables Power Supply Using A Switch Power Supply When Connected Directly To A Computer Power Supply With Power Over Ethernet Products Variable PoE Camera Startup Sequence Operating The Camera Manual and Automatic Operation Overview Manually Using A Computer In The 10 x x x IP Address Range Automatically Using Mx
41. 1 27 times higher than that of the M12 due to the use of five megapixel technology Image detail is improved by 27 percent As a result an M15 can now be installed even further away than before from the objects and areas to be monitored In addition this relativizes the horizontal image angles of the new five megapixel sensors that are slightly smaller compared to the M12 Flexible And Future Proof The system can easily be matched to suit the location s requirements thanks to a range of available sensor modules You can change the sensor modules to modify the focal lengths at any time MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 AllroundDual New Features Of The M15 Compared To The M12 At A Glance Modular design M15 Core Camera housing with front element sensor modules may be ordered individually IP66 Dust proof and resistant to water jets M12 IP65 Sensor modules including lens and image sensor Up to two can be connected simultaneous display and recording installation and expansion by the user no need to send it back to the MOBOTIX factory Flash memory internal DVR MicroSD card replaces SD card and R models of the M12 MiniUSB For peripheral devices adapter cable available from MOBOTIX MxBus Enables the two wire connection of MOBOTIX interface boxes Power supply Via a blue NPA PoE Set MX NPA Box or standard PoE switch
42. 10 4 GB 20 8 GB Time for one full cycle 12 hours 4 hours 14 4 hours 9 2 hours 4 4 hours The MicroSD card s service life depends on production quality and frequency of use Set the type of recording event controlled or continuous recording frame rate resolution according to your specific requirements We recommend changing the pre installed high quality 4 GB MicroSD card once a year if you have it constantly set to continuous recording Monitoring The Cell Wear Of Flash Storage Devices Patent Pending MOBOTIX uses its own technology for this purpose and has a pending patent You can view the flash wear in the status bar of the live image or by opening Admin Menu Camera Status In addition the camera can also send a warning message for example via e mail as soon as a critical error is detected when data is written to the SD card Admin Menu Error Notification Function The MicroSD card can then be replaced to ensure that any existing data is not lost Dateiserver Flash Medium Typ SD Flash Card Dateisystem MxFFS Puffer Auslastung 0 O 0 max 0 Verloren gegangene 0 Alarmbilder Sequenzen 1 1 Dateien Neueste Sequenz 1970 01 01 01 00 00 0 lteste Sequenz 1970 01 01 01 00 00 0 Aktueller Speicherbedarf 4 0 MByte 0 495 Max Gr e 936 MByte MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com All specifications are based on calcu lated ave
43. 106 mm 4 17 in 5 m N eo ceo 5 5 N e eee 4 207 mm 8 15 in 106 mm 4 17 in ATS 5 m N eo E E o E E w N y Y MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 Camera Manual Product Overview 36 1 3 2 L12 Sensor Module 2 1 Item Number Part Name 2 1 Sensor module with affixed washer 2 2 L12 lens installed 2 3 Dome installed 24 Cable retainer with bayonet catch installed 2 5 Sealing plug blue small installed 2 6 Nut plastic MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Delivered Parts and Dimensions Front View LEDs deactivated Sensor module housing Microphone deactivated Rear View Markers for top Sensor cable con nection Sensor module housingl Pressure compen sation Side View Sensor module weight without lock ring 85 g weight with lock ring 91 g d aid Diam 50 mm 2 in Diam 50 mm 2 in Diam 43 mm 1 in 58 mm 2 3 in 30 mm 1 2 in 15 lt q dh Diam 43 mm 1 7 in m 0 6 in Diam 43 mm 1 7 in lt MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobot
44. 130 3 6 Overview 130 3 6 2 General Browser Settings 132 3 7 Additional Notes 134 3 7 1 Operation with Only One Sensor Module 134 3 7 2 Password For The Admin Menu 134 3 7 3 Permanently Deactivating The Microphone 134 3 7 4 Starting The Camera With The Factory IP Address 135 3 7 5 Resetting The Camera To Factory Settings 135 3 7 6 Activating Event Control And Motion Detection 135 3 7 7 Deactivating Text And Logo Options 135 3 7 8 Deactivating The Camera Reboot 136 3 9 Browser 136 3 7 10 Cleaning The Camera And Lens 136 3 7 11 Safety Warnings 136 3 7 12 Online Help In The Browser 137 3 7 13 RoHS Declaration 137 3 7 14 Disposal 138 3 7 15 Disclaimer 138 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 5 144 4 M15 Camera Manual Contents AN Declaration Of Conformity M15 AllroundDual 142 Manufacturer 143 Important Notes Electrical Installation Electrical systems and equipment may only be set up changed and maintained by a qualified electrician or under the direction and supervision of a qualified electrician in accordance with the appropriate electrical guidelines Legal Aspects Of Video And Sound Recording You must comply with all data protection regulations for video and sound monitor ing when using MOBOTIX products Depending on national laws and the installation location of the MOBOTIX AllroundDual M15 the recording of video and sound data may be
45. 6MEGA Image formats configurable per sensor Selectable image formats for example 2048x1536 3MEGA 1920x1080 full HD 1280x960 MEGA 1280x720 HD 1024x768 800x600 768x576 DI PAL 704x576 TV PAL 640x480 384x288 320x240 160x120 Max frame rate M JPEG VGA 30 fps MEGA 10 fps 3MEGA 4 fps live recording 6MEGA 2 fps Max frame rate MxPEG VGA 30 fps MEGA 30 fps 3MEGA 20 fps live and recording incl sound 6MEGA 8 fps Image compression MxPEG M JPEG JPEG H 264 SIP video only Internal DVR MicroSD slot including 4 GB max 64 GB External video ring buffer Up to 4 TB directly on NAS and computer server without additional recording software Software included MxEasy video management software MxControlCenter control center software MOBOTIX App for iOS devices from Version 5 0 Image processing Backlight compensation automatic white balance image distortion correction video sensor motion detec tion MxActivitySensor Virtual PTZ Digital pan tilt zoom continuous 8X zoom Alarm events Video motion detection MxActivitySensor external signals temperature sensor PIR microphone shock detector notification via e mail FTP IP telephony VoIP SIP visual acoustic alarms pre and post alarm images Microphone and speaker Integrated microphone and speaker Audio functions Lip synchronous audio two way communication au
46. 7 Installation Ansicht laden Ansicht speichern Automodus Panorama Doppel Panorama Panorama Fokus Autzeichnung Aufzeichnung Aufl sung Bildprogramm Helligkeit Belichtungssteuerung Farbs ttigam Gegenlichtkorrektur Scharte JPEC Qualit t DDAA lt lt A Load Default View 2 Rotate the live image in the desired direction using the mouse or a joystick con nected to the computer T8 Ausw hlen me Admin Menu Setup Menu Arm amp Record MXPEC on J MXPEG off 3 High Quay _Paysouna _ Pay Last tvert Memwateher 1x Zoom Set Default View Load Default View MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Virtual PTZ And Full Image Recording 21 144 3 In the Installation Quick Control select the Set North option MOBOTIX Installation Ausw hlen via Anzeige Modus Auswahlen Admin Menu vPTZ Wand Setup Menu Ansicht laden Norden festlegen Ansicht speichern Automodus Aufzeichnung i Ril Aufl sung Bildorogramm Bildqualitat Helligkeit Relichrungssteuerung Farbsattigung Gegenlichtkorrektur Senarte ap PEG Qualitat Scnartsrelihilte Center Pan Set Default View Load Default View 4 Store the desired North direction permanently by first activating the checkbox and then clicking on Yes MOBOTIX Q24 m
47. And Full Image Recording All standard motorized PTZ cameras only store the image sequence that is currently viewed in the live image live image recording This has one serious disadvantage as the recording can only show what has happened in the visible portion of the image The rest is lost and cannot be examined later on MOBOTIX has hence added the new full image recording feature to the M15 When you activate this feature the camera will not store the currently viewed image that reflects the pan tilt position and the zoom setting chosen by the user but the full sensor image without vPTZ settings When examining the recorded images at a later date the vPTZ features again come into play as they allow you zoom in on the visible image and use the pan tilt features to examine every corner of the recorded full image Internal DVR The M15 SEC and IT models features direct recording to an integrated MicroSD card which makes the camera fully independent of any external storage media even for longer periods of time The camera internally stores high resolution video without requiring an external recording device or PC and therefore without overloading the network whatsoever Old recordings can be overwritten or deleted automatically after a specified period of time A 32 GB MicroSD card for example allows the camera to store more than half a million event images in VGA format 640x480 If you would like to archive complete sequences
48. Change under Power E ELE pes PoE saich Generally t e Supply curren wich erac Fa are you can Ue a IP Off ei So delov k interface using the marc 2 OJ This shows accessing the comers e i two dflerert IP adresos 3 A Power Wizard will appear to te rint guide you through the PoE con oF ME or DE e figuration steps Mr ee iat ghost nir aed oes drei her vile I m setting also controls the power allocation in the connected network 4 Next restart the camera Disconnect The currently active power supply is Power over Ethernet Class 2 the camera from the power supply Then reconnect it for example by disconnecting and then reconnect ing the Ethernet cable at the PoE switch Camera Name Ethernet Parameters Power Supply Set X Power over Ethernet Class 1 mit Select the desired power supply method below If you are using a PoE switch to power your camera it may be necessary to soloct a lower PoE class for the cameras so you can use all ports of the switch Ok Cancel MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Network And Power Connection 8 9 144 2 7 6 Camera Startup Sequence As soon as the power supply has been established LEDs 1 and 2 will show the progress of the startup sequence LED default settings Q Q 1 Power on Error flashes 2 Recording flashes e Booting Immediately after connecting
49. ControlCenter Or MxEasy Automatically Using DHCP First Images And The Most Important Settings Manually Setting Up The Network Parameters In A Browser First Images And The Most Important Settings In The Browser First Images And Network Parameter Configuration In MxControlCenter 50 50 50 53 56 57 58 59 59 61 62 63 64 66 67 68 70 70 74 74 78 79 83 85 85 86 87 87 88 89 90 90 91 92 93 94 94 96 98 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Contents 3 2 4 First Images And Network Parameter Configuration In MxEasy 103 3 2 5 Starting The Camera With The Factory IP Address 106 3 2 6 Starting The Camera With An Automatic IP Address DHCP 107 3 3 Adjusting Camera Lens Focus And Installing A Filter 108 3 3 1 Adjusting The Camera 108 3 3 2 Adjusting Lens Focus L76 L160 Only 109 3 3 3 Inserting A Filter 110 3 4 Virtual PTZ And Full Image Recording n 3 4 1 Preparing The Virtual PTZ Function 11 3 4 2 Full Image Recording 113 3 4 3 Special MI5 Configuration In The Browser 115 3 5 MicroSD Card Recording 124 3 5 Introduction 124 3 5 2 Formatting The MicroSD Card 126 3 5 3 Activating Recording 127 3 5 4 Accessing Data on the MicroSD Card 128 3 5 5 Deactivating Card Recording 128 3 5 6 Using A MicroSD Card In A Different MOBOTIX Camera 129 3 5 7 Limitations On Warranty When Using Flash Storage Media 129 3 6 Configuration In The Browser
50. Image width infinite 34 7 20 6 14 5 9 7 4 6 Image height 220 23 7 14 9 10 8 7 2 3 4 At 50 m distance Image width N A 86 8 alo 36 2 24 3 11 4 Image height N A 59 3 37 3 27 0 18 0 8 6 The specified focal lengths of the MOBOTIX lenses do not reflect the actual focal length of the lenses but the focal length Lxx mm converted to 35 mm camera format For example the MOBOTIX L25 Super Wide Angle lens has an actual focal length of 4 mm This would be the equivalent of 25 mm on a 35 mm camera It is therefore referred to as an L25 Since the image sensors in digital cameras have different sizes converting the focal lengths to 35 mm camera as a known format allows the image formats and the fields of vision of the different lenses to be calculated and compared more easily Another benefit is that you can easily set a 35 mm camera analog or digital to the same focal length as the MOBOTIX lens Lxx to obtain the same field of vision This approach greatly facilitates lens selection MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 26 144 M15 Camera Manual Product Overview 1 2 2 Camera Variants Lenses Hardware Image Formats Camera Model M15D SEC Hemispheric 12 mm L12 Super Wide Angle 25 mm L25 Wide Angle 38 mm L38 Wide Angle 51 mm L5 Tele 76 mm L76 Tele 160 mm L160 CSVario 24 to 54 mm Image sensor with indiv
51. MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com MicroSD Card Recording 127 144 3 5 3 Activating Recording Follow these steps to activate the recording to a MicroSD card that has already been MxFFS formatted Admin Menu Storage on External File Server Flash Device 1 2 3 4 5 Make sure that there is a MicroSD card in the card slot of the MOBOTIX camera Make sure that the MicroSD card is formatted in MxFFS format Activate the SD Memory Card option Click Set and then Close to store the configuration Reboot the MOBOTIX camera Admin Menu gt Reboot Camera Once the camera has rebooted make sure that the camera displays the FR REC symbol in its live image If this is the case the camera uses the MicroSD card as recording target If not you must activate the recording see below Activating The Recording Ifthe FR REC symbol is not visible in the live image after rebooting you need to activate the recording using one of the following methods In the web browser Automatic activation by clicking on the Arm amp Record softbut ton Confirm this in the Easy Dialog by clicking on the Yes button In the web browser Manual activation via the Quick Control Recording gt Recording On or in Setup Menu gt Recording MxEasy It is possible to activate the recording based on the time or date using the Alarm Planner of MxEasy see MxEasy User Manual Encry
52. OTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Default user data User name admin password meinsm Download the Software Camera Manual Part 2 from www mobotix com in the Support Manuals section 96 144 M15 Camera Manual Operating The Camera 3 2 2 First Images And The Most Important Settings In The Browser Once the MOBOTIX camera has been connected to the power supply and to the network you can access the user interface with the live camera image in the web browser Internet Explorer Firefox Safari or any other graphical browser with activated JavaScript is suitable It does not matter which operating system is used After entering the camera s IP address in the browser address bar you will see the live view of the MOBOTIX camera with its user interface controls such as softbuttons buttons for the different camera screens pull down menus Quick Controls icons for accessing the online help and the camera status and status information elements O 2 r A as http 10 8 0 99 x Google Dp i Live x MOBOTIX D Admin Menu Setup Menu Arm amp Record Audio o MxPEGon MxPEG off UC Event x LEDs Bl nk Play Sound Play Last m Center Pan Normal Image Surround Image Auto Move on S Auto Move off D Fertig amp Default access data for the adm
53. Status Symbol ng y Lor i On will draw a symbol in the image to visualize the current arming and recording status Full Image Recordi Activate Full ig TE g ng On wili alwa 5007 the Full Miage of the sensor with the s tied parameters Offf ill record the visible imag i Recordi n Activate Terminate Recording Terminate rding TR _ off Terminate recording it an event is detected Use this option to freeze stored images Click here to resume recording Storage Settings Value Explanation Recording REC Event Recording t arp oe ai Snap Shot Recording stores single JPEG pictures Event Recording stores stream files for every event using MxPEG codec Continuous Recording continuously streams videodata to stream files using MxPEG codec 2 a Record Audio Data Include audio Store audio data in stream file if available Enable and configure microphone Start Recording Select the events which will start recording Use Ctri Click to select more than one event EC Event Counter Events in brackets need to be activated first z EL Event Logic EC or EL for filtered events E12 Evant lonoic 2X C se X Factory Restore X Close w 4 gt MOBOTIX Q24 mx10 8 0 113 Full Image Recording Attribute Value Explanation ege ue QXGA 2048x1536 Fairy defaut Mega 1200x980 JPEG Quality 60 High i T r 2 Text Display ext Display Date amp ti
54. The Ethernet connection cable of the camera has already been guided through the mount and simply needs to be connected with the network cable on site for example using the MX Patch Box By adjusting the VarioFlex mount as required the captured image area can be precisely adjusted to the desired practical application The camera can be turned or tilted 180 horizontally and 80 vertically from 60 to 20 Ceiling Installation By exchanging the wall mount for the separately supplied ceiling mount the M15 is ready to be installed on ceilings in just a few easy steps thanks to the VarioFlex system This installation option is of particular benefit when monitoring rectangular rooms with a single camera In such cases the L25 sensor module with Super Wide Angle lens allows the room to be monitored almost entirely by an M15 installed on the ceiling in one of the corners Using the PTZ software you can easily zoom in on image details in either the live image or the recording The camera can be turned or tilted 360 horizontally and 107 vertically from 90 to 17 MOBOTIX AG gt Security Vision Systems Made in Germany www mobotix com sales mobotix com Preparing The Installation 53 144 Installing On A Pole With Accessories Installation on round poles is frequently used for cameras that are intended for mobile outdoor use for example surveillance of construction sites For this purpose MOBOTIX recommends u
55. ade in Germany www mobotix com sales mobotix com The default IP address of your camera is printed on a sticker on the front 92 144 M15 Camera Manual Operating The Camera Download the free of charge MxEasy and MxControlCenter software at www mobotix com MxEasy free download from www mobotix com 3 1 2 Automatically Using MxControlCenter Or MxEasy You can set up the camera s network parameters using the free video management software MxControlCenter or MxEasy see Section 3 2 3 and Section 3 2 4 You can also use one of these applications to automatically configure the network parameters of MOBOTIX cameras that are not operating on the same IP address range as the computer E tasContrelCenter Inside Player rrr i File View Layout Video Scurce Recording 0 gt 5 aia 4 I Oves Outece Man Entrance vest gate Parking Garage Entrance qa Player m 16 11 06 14 41 00 ELI hes Seftuttens reU enter v Advantages You can connect the camera directly to the target network The camera does not need to be physically accessible that is it may already be installed The camera can be configured to automatically receive an IP address optional The network parameters can be manually set optional You do not need 10 access the camera software Requirement Either MxControlCenter or MxEasy must be i
56. aken down to remove insert or replace a MicroSD card in use To avoid data loss be sure to deactivate MicroSD card recording in the camera software and reboot the MOBOTIX camera before removing the card Caution A MicroSD card may only be removed from the camera after you have deactivated recording to the SD card and rebooted the camera Failing to do so may lead to data loss Make sure that the card is not write protected Procedure l Deactivate recording Recording to the SD card must be deactivated Admin Menu Storage on External File Server Flash Device If the MicroSD card recording is still active deactivate recording reboot the camera and then disconnect its power supply For more information see Section 3 5 MicroSD Card Recording 2 Open camera housing Open the camera housing as described in Section 2 2 2 3 Remove connection cable from the inner cover of the housing Remove the con nector of the sensor cable and the I O cable red clips after opening the clip catches Remove Ethernet cable and any connected MiniUSB cable after opening the bayonet catch Remove MxBus cables Make sure the front element with the sensor modules does not fall down 4 Remove inner cover Remove the four lock screws me on the inner lid red arrow using the supplied 2 5 ad mm Allen wrench and carefully lift off the lid 7 J A Make sure that the interconnections befween the 5 inner lid and the circuit board are not
57. ample replace one sensor module instead of the entire camera MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 AllroundDual 11 144 Ethernet patch cable MiniUSB MxBus PoE switch The Right Sensor Module For Every Application Twelve different sensor modules are available for the M15 Six focal lengths from telephoto to hemispheric each available in day or night versions with a horizontal image angle of 13 27 39 54 82 and 180 You can exchange all sensor modules on site whenever necessary The image area cap tured by the camera varies depending on the focal length of the built in lens With a Super Wide Angle lens 82 image angle for example almost an entire room can be recorded from just one corner And a telephoto lens 13 image angle for example enables the M15 to clearly record a license plate number from a distance of approximately 75 meters Or even the serial number of a dollar bill from a distance of two meters One M15 camera is usually all that is required to monitor either an entire room or the four lanes of a gas station The high degree of image detail not only reduces the number of required cameras but also minimizes system costs by reducing the wiring complexity emergency power requirements and number of recording devices required 5 Megapixel Image Sensor Technology The M15 features a significantly increased level of per
58. ancing the reliability of the system as a whole When using a more powerful 19 rack mounted UPS you can also protect all other network components for example switches routers PoE switches etc Since MOBOTIX cameras do not require any heating even during winter the average power consumption of less than 5 watts is very low This in turn means that you can centralize the UPS protected power supply by injecting power into the Ethernet cables max 100 m This kind of protected power supply can be used either with MOBOTIX PoE products MX NPA PoE Universal Power Supply or with PoE compliant switches according to IEEE 802 3af ego A 2 1 4 Preparing The Camera Connections Wall Outlets MX Patch Box Once the camera position the position of the cable connectors and the method of power supply have been decided upon the cabling can be installed Before installing the MOBOTIX M15 you should make sure that the network connections have been properly tested so that the proper functioning of the camera is guaranteed If the M15 is to be installed outdoors the MX Patch Box from MOBOTIX should be used optional accessory The MX Patch Box enables you to connect a MOBOTIX camera with a patch cable or an Ethernet installation cable in a simple and watertight manner For more information on the MX Patch Box and the other interface boxes please visit www mobotix com and go to the Products gt Accessories gt Interface Boxes section
59. and 7 1 Open Start gt Settings gt Control Panel gt Network Fi Connections Clicking on Properties opens the dialog Ng inel PRO Corfguee box shown eT aa v Bh Chert for Microsolt Networks v File and Printer Sharning for Microsoft Networks Scheduler Local Area Connection Properties 2 Double click on Internet Protocol TCP IP On the General tab activate the Use the following IP address option Enter an IP address in the 10 x x x range in this field for example 10 8 0 11 Internet Protocol TCP IP Properties General You can get IP settings assigned automatically your nelwork supports 3 Onceall dialog boxes have been closed the computer SEXT will have the IP address 10 8 0 11 um Delad gateway MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com First Images And The Most Important Settings 95 144 Linux Unix 1 Open a terminal as root user 2 Enter the following command ifconfig eth0 1 10 8 0 11 3 The computer is now also using the IP address 10 8 0 11 Mac OS X 1 Open System Properties gt Network 2 Select Ethernet In the Configuration field select ie m Manual and enter a 10 x x x IP address for example OD 10 8 0 11 LEE e 3 Click on Apply on the bottom right hand side of the Mice dialog box to assign the computer the IP address LB ll i n ntm rnt TIT 2 Set Up Th
60. ashers 5 5 4 Stainless steel hex nuts M6 5 6 2 Stainless steel straps The caps for the screws are also required here These are included in the delivery of the wu M15 basic module see Section 1 3 Delivered Parts and Dimensions item M 10 2 4 Screw 6005 for lock screws MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Mounting The Camera With Pole Mount Accessories 8l 144 Procedure 1 Prepare the cable Guide the on site network cable from behind through the middle opening of the pole mount Ideally the cable should be guided directly from the pole into the cavity socket of the VarioFlex wall mount where itis connected with the camera patch cable concealed cabling via an adapter such as MX Patch Box Prepare the straps Guide the two stainless steel straps through the pole mount The pole must have a diameter between 60 mm and 180 mm Attach pole mount Place the straps around the pole and tighten them using a screwdriver If necessary the ends of the straps can be cut off Attach rubber sealing ring Place the white rubber seal ing ring with the groove on the edge of the wall mount Connect the cable Connect the on site network cable to the camera patch cable using an adapter or insert the patch cable into the RJA5 outlet Take note of the installation manual included in the package when using a MX Patch Box All manuals ca
61. bayonet catch installed 4 5 Sealing plug blue small installed 4 6 Nut plastic MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Delivered Parts and Dimensions Front View 5 LEDs deactivated g E E Sensor module 2 housing 0 Microphone deactivated Rear View Markers for top Sensor cable con nection Sensor module housing Diam 43 mm 1 7 in Pressure compen sation Diam 43 mm 1 in Side View l 48 mm 1 89in 15 i eli in Ac Fs S E E Sensor module S weight without lock ring 122 g weight with lock ring 128 g E yo MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 42 144 M15 Camera Manual Product Overview Only cables with angled plugs can be used for the M15 1 4 Available Accessories 1 4 1 Polarization Filter Order no MX SM OPT POL The polarization filter can suppress annoying reflections and thus enhances recognizability of persons behind windshields for example This filter replaces the protec tive glass insert into the corresponding sensor module Use the blue lens wrench M 6 to rotate the polariza tion filter and to adjust its orientation see Section 3 3 3 Inserting A Filter Due to its nature this filter reduces the amount of light that enters the l
62. bled VarioFlex wall ceiling mount in addition to two HiRes image sensors The weatherproof MxBus and MiniUSB interfaces allow for direct connection of MOBOTIX interface boxes and standard devices such as UMTS modules additional memory etc With the M15 one or two separately available MOBOTIX sensors modules lens plus sensor board and microphone that can be replaced at any time are used in the M15 Core basic camera module Twelve different sensor modules are available for the M15 Six focal lengths from telephoto to hemispheric each available in day or night versions With the Day amp Night models with day and night sensors the camera switches off to the appropriate sensor depending on the lighting conditions The latest five megapixel technology ensures crisp HiRes images limited to 3 1 megapixels with improved live digital zoom and increased light sensitivity so that clear color images are always produced even at dawn and dusk At night a single black and white sensor module now also produces high resolution images up to 3 1 megapixels If both sensor images are displayed or recorded at the same time the M15 delivers dual images up to six megapixels The MxEasy and MxControlCenter video management software which is tailored to MOBOTIX cameras and a PDF manual can be downloaded from the MOBOTIX web site at no cost www mobotix com gt Support gt Software Downloads MOBOTIX also provides a mobile solution for the iPad iPhone and iPo
63. can be completely configured using a JavaScript enabled browser on all common operating systems such as Windows Linux Macintosh etc The camera provides a HTML based user interface for this purpose The camera executes the changes you make to the camera configuration via HTTP commands using programs and scripts of the embedded software The settings are stored in the camera s flash memory This section contains an overview of the general browser settings of the MOBOTIX camera as well as further configuration options Detailed information on the software functions is provided in the camera s online help MOBOTIX Q24 10 8 0 79 Live Bo E D S3 Admin Menu Setup Menu Arm Audio on amp MxPEG n MxPEG off S gt oseink MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Configuration In The Browser 131 144 Basic Settings Administering the camera You can modify the camera configuration in the Admin Menu or the Setup Menu Admin Menu This menu contains the basic configuration dialog boxes of the camera for example passwords interfaces software updates Setup Menu This menu contains the dialog boxes for configuring the image event and recording parameters Some of these settings can be changed using the corresponding Quick Controls in the live view Resetting changes If you would like to reset some la
64. ce Boxes Insert the MOBOTIX patch cable of the M15 into the network port for standard connections only permitted in indoor areas If additional cables are required inside the housing they must be connected as described in Section 2 2 6 Connecting a USB Cable and Section 2 2 7 Connecting a Two Wire MxBus Cable 2 7 2 Power Supply Using A Switch l Connect the factory pre installed cable of the camera to the camera connector of the PoE adapter 2 Connect the LAN Power connector of the PoE adapter to the Ethernet connector of the switch router or the Ethernet port 3 Plug the 145 connector of the power supply unit into the PC Power connector of the PoE adapter PoE adapter MX NPA PoE Switch router Power supply LAN www Camera 10 8 0 99 PC 10 8 0 11 255 0 0 0 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Network And Power Connection 87 144 2 7 3 Power Supply When Connected Directly To A Computer 1 Connect the factory pre installed cable of the camera to the camera connector of the PoE adapter 2 Connect the PC Power connector of the PoE adapter to the Ethernet port of the computer 3 Plug the RJ45 connector of the power supply unit into the LAN Power connector of the PoE adapter PoE adapter MX NPA PoE Power supply Camera 10 8 0 99 2 7 4 Power Supply With Power Over Ethernet Products Connect the
65. cted video sources option here MxControlCenter automatically generates a grid layout that displays windows of the same size for all selected video sources Give each layout a unique name for example Underground garage If you select the second option the video sources you selected are simply integrated in the MxCC system where you can use them to generate a layout at a later time Click OK to confirm your selection MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com First Images And The Most Important Settings 103 144 3 2 4 First Images And Network Parameter Configuration In MxEasy Installing And Starting MxEasy Download the current version of MxEasy from the MOBOTIX website www mobotix com gt Support Software Downloads in the MxEasy area Double click the shortcut for the program or the program file Finding Cameras When you start MxEasy for the first time on a computer the MxEasy Wizard automatically begins to search for MOBOTIX cameras and displays all the cameras found in a list The camera list will be updated automatically as soon as new MOBOTIX cameras are con nected to the local network or removed from the network Bits Wizard Ex Camera Selection Please select up to 11 additional cameras to monitor and configure with MxEasy MOBOTIX You can double click on a camera to change its name Use the context menu right click to add a camera manually
66. d 3 satisfactory MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Preparing The Installation 5 5 144 Furthermore the camera view from top to bottom can also be achieved by installing the camera on a wall or a pole at a tilt of 90 Weatherproof housing visible in the full image v Panning tilting zooming removes the area concealed by the weatherproof cover Sc gt P pu EA kd TAN A Part of the captured image area is concealed behind the protective cover of the M15 housing especially in the full image For this reason MI5 cameras with L12 lens should be adjusted so that the concealed areas are not those that are supposed to be monitored The concealed area can be completely removed from the image by panning tilting zooming the image using the virtual PTZ function MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 56 144 M15 Camera Manual Installation The M15 supports Power over Ethernet according to IEEE 802 3af PoE The PoE adapter replaces the crossover cable when directly connect ing to a computer sess ee teens 2 1 3 Network Connection And Power Supply UPS Power Over Ethernet PoE Conforming To IEEE 802 3af All M15 models are supplied with power using the PoE standard The PoE Adapter Set MX NPA PoE Set may be used
67. d Touch iOS devices Search for MOBOTIX AG in the App Store to find the free app If you still have any questions our support and international sales staff are available at intl support mobotix comfrom Monday to Friday 8 a m to 6 p m German time Thank you for choosing MOBOTIX products and services We wish you all the best with your new high performance MOBOTIX M15 AllroundDual camera MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Security Vision Systems MOBOTIX MOBOTIX AG Security Vision Systems Made in Germany www mobotix com salesemobotix com 10 144 M15 Camera Manual Product Overview 1 PRODUCT OVERVIEW M15 AllroundDual 1 1 1 General Product Characteristics The HiRes Dual Camera System For All Your Needs The M15 AllroundDual camera is a well equipped professional network camera that is top of the MOBOTIX product range both in terms of functionality and technological capability The integration of two image sensors and a range of other functions and technical innova tions results in unlimited usage possibilities For video security applications in commercial private and public sector environments as a surveillance or weather camera a webcam indoors or outdoors day or night Caution MOBOTIX In Use It is clear from the outset that the M15 is an authentic MOBOTIX camera like its predeces sor the M12 It offers
68. d through integrated color filters The day and night lenses in the M15 are positioned exactly parallel to one another This way the day lens always covers the same area as the night lens Hemispheric Day And Night Camera M15 With Sensor Modules D12 And N12 The M15 is a hemispheric dual camera for use in extremely variable lighting conditions equipped with two L12 lenses each with a black white and color sensor The M15 is designed in such a way that both of the camera s sensor modules are positioned in parallel in order to see the same image area as a color image during the day and as a black white image at night Robust And Low Maintenance The M15 has been manufactured with the highest level of quality in mind always Only quality tested high grade materials and components are used MOBOTIX cameras do not have any mechanical motors to operate the lenses or move the camera making them so robust that maintenance is reduced to a minimum Cleaning is simple You only need to wipe the lens using a soft cotton cloth and a mild household detergent without abrasive particles Weatherproof Without Heating Or A Fan The entire camera plus cables and sensor modules are weatherproof IP66 Thanks to their low power consumption less than five watts and the total absence of mechanical moving parts M15 cameras feature the highest operating temperature range from 30 to 60 C 22 F to 140 F Since the cameras neither fog up nor require h
69. dio recording Interfaces 10 100 Ethernet MiniUSB MxBus inputs outputs and RS232 via accessories MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Technical Specifications Technical Data 5 Video telephony VoIP SIP two way communication remote controlling with key code event notification Security User group management HTTPS SSL IP address filter IEEE 802 1x intrusion detection digital image signature Certifications EMV EN 55022 CISPR 22 EN 55024 EN 61000 6 1 2 FCC Part15B CFR 47 AS NZS 3548 Power supply Year round Power over Ethernet IEEE 802 3af PoE class variable approx 5 W M15D 4 5 W M15M Operating conditions IP66 30 to 60 C 22 to 140 F Dimensions weight M15 without sensor modules W x H x D with wall mount 158 244 x 239 mm W x H xD with ceiling mount 158 x 210 x 207 mm Weight with wall mount Approx 1 1129 g Weight with ceiling mount approx 1 078 g Dimensions weight Sensor modules L12 diam x H 43 x 45 mm installation dim weight 85 g L25 151 diam H 43 57 mm installation dim weight mg L35 L76 L160 diam x H 43 x 60 mm installation dim weight 122 g Delivered parts Housing high resistance composite PBT white shock resistant dome for L12 sensor module coated glass pane for all other sensor modules accessories for installation on wal
70. dule Note that the sensor modules are not yet protected against theft and unwanted rotation e g due to vibration In such a case it is highly recom mended to install the security clips M 11 Blind module e Section 2 2 2 Opening the Camera Housing e Section 2 2 3 Installing the Security Clips Optionall e Section 2 2 8 Closing the Camera Housing 2 2 2 Opening the Camera Housing The following tasks require opening the camera housing and removing the front element of the M15 in order to get to the interior of the M15 e Inserting security clips at the sensor module or the blind module respectively e Exchanging the MOBOTIX Ethernet patch cable against a longer MOBOTIX patch cable e Connecting an MxBus two wire cable in order to attach MxBus extension modules e g the MX GPS Box e Connecting a MOBOTIX USB cable in order to attach external data storage devices or an MX 232 IO Box e Exchanging the pre installed SD card 4 GB against a larger one or as preventive maintenance measure see Section 3 5 MicroSD Card Recording MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 6 2 44 M15 Camera Manual Installation Procedure l Place the camera face down on a clean and dry surface 2 Remove the two rubber plugs at the back of the camera housing 3 Using the supplied 5 mm Allen wrench loosen Remov
71. e Target Network Parameters Of The MOBOTIX Camera 1l Open a web browser on the computer and enter the default IP address of the MOBOTIX camera in the address bar of the browser for example 10 8 0 99 Pressing Enter displays the user interface of the MOBOTIX camera see also Section 3 2 2 First Images And The Most Important Settings In The Browser 2 Clickon the Admin Menu softbutton in the user interface of the MOBOTIX camera The Quick Installation starts automatically once the Admin Menu admin user has logged on Note The Quick Installation can also be executed at a later stage by opening Admin Menu Network Setup Quick Installation see also Quick Installation in the Camera Software Manual Part 2 3 Enter the target network parameters of the camera on the appropriate page of the Quick Installation assistant cones Quick Installation net interface 953065 Car be reached Grectly on your LAN in order to access Ihe your computer via LAN your Computer seeds an P address oF the System admerestrator for a valid and ursque IP address and Note The network parameters can also be modi SEE fied retrospectively via Admin Menu gt Network Configuration Quick Installation 4 Once you have completed the Quick Installation and rebooted the camera the new network parameters will be activated The camera can now be connected to the target network and if required further configured MOB
72. e camera software or MxEasy as standard Tilted vertical lines if the camera is mounted at an angle may be optically MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com 15 144 16 144 M15 Camera Manual Product Overview straightened to the image edges using this feature A welcome side effect of this is that the protective cover disappears from the image If this measure does not work in a specific situation downward camera tilt not possible the protective cover can be removed from the image by zooming and if necessary by panning downward using the virtual functions The displayed image section or the panorama as the case may be is reduced slightly but the image details are enlarged as a result of zooming Original full image Panorama Focus One Camera Three Views Maximum room overview while simultaneously viewing detail in a single image The M15 is capable of providing two more views at the same time with the panorama allowing you to focus on two scenes in parallel Panorama Focus display mode Virtual PTZ 1 MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 AllroundDual 7 144 Double Panorama For A Simultaneous View In Two Directions The Double Panorama display mode provides a panorama image of both halves of the surveillance area Using the vPTZ functions the panorama images can be changed
73. e mail or IP Notify with the alarm image placing a phone call uploading an alarm image to an FTP server switching a signal output line of the camera for example for switching on the lights opening a door For the settings see Setup Menu Action Group Overview The actions to be performed are defined and used in these action groups in the form of action pro files The different action profiles can also be defined in the following areas Admin Menu in the Hardware Configuration profiles for signal output Transfer Profiles FTP e mail IP Notify and Sound and VoIP Telephony sound profiles VoIP profiles For more information refer to the online help for the Action Group Overview dialog box e Activate shock detector The M15 is also equipped with a shock detector as standard for all IT and Secure models If for example the camera s housing receives a blow it automatically registers it and sends a notification via an IP Notify or telephone call A general advantage is that MOBOTIX cameras are extremely tough not least because of the absence of mechanical moving parts This typically allows them to stay fully operational in particular when they are subject to strong vibrations Open the Setup Menu lt Event Control Environment Events lt Edit dialog box if you would like to activate the shock detector and any other sensors MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com
74. e rubber the two bolts at the back of the camera housing the back of the housing Leave the bolts and washers in the camera housing using small screwdriver 4 Using the Allen wrench cautiously push from behind in an alternating fashion onto the left and the right bolt red arrow in upper figure and push the front element out of the front of the housing 5 Tilt the front element forward as shown in the figure 2 2 3 Installing the Security Clips Optional The security clips are protecting the sensor modules or the blind module in the front ele ment of the M15 against unwanted rotation e g due to vibration when mounted on a pole or in an automotive scenario Procedure 1 Open camera housing Open the camera housing as described in Section 2 2 2 2 Insert the security clips To protect the modules against unwanted rotation insert the two red secu rity clips at the insides of the sensor modules as shown in the figure Make sure that the security clips click into place as shown in the image detail 3 Close camera housing Close the camera housing as described in Section 2 2 8 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com First Installation Steps 63 144 2 2 4 Exchanging Sensor Modules Note that you only need to follow this procedure if the security clips M11 have been installed Since the sensor modules cannot be exchanged from the outside in
75. e to store either the section of the live image that is visible or the full sensor image full image storage This also allows you examine parts of an image or video that had not been visible in the live image section on display at the time of the recording Unlike in the camera systems from other manufacturers there is no need to buy and install additional software on your computer thanks to the MOBOTIX firmware that can be accessed directly in a web browser via the camera IP address Instead of using a web browser you can also download the free MxControlCenter or MxEasy video manage ment software from the MOBOTIX website www mobotix com gt Support to quickly display multiple cameras on one monitor or on an entire video wall switch alarms with sound or conveniently search for an event The MOBOTIX App for iOS devices iPhone iPad iPad mini iPod touch is also available free of charge from the App Store for your mobile applications from Version 5 0 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com MOBOTIX Software 47 144 1 5 2 MxControlCenter The MxControlCenter video management software can be used to combine any number of cameras at any locations into a well structured and powerful video security system with centralized or local access protected operation and analysis The state of the art software specifically tailored to support high resolution MOBOTIX netw
76. eating power can be supplied via the network cabling according to the PoE standard IEEE 802 3af MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 AllroundDual Fast Simple Installation The MOBOTIX M15 requires just one cable for data and power to connect to a PoE switch and thereby to any expandable Ethernet network The VarioFlex mount supplied as standard makes the camera ideally suited for outdoor use and for installation over in wall sockets so that the cabling remains perfectly concealed A number of additional devices can be used They are connected via a network switch or directly to the camera housing via an MxBus or MiniUSB cable for example ExtlO MOBOTIX functional boxes audio devices flash drives or UMTS Wi Fi USB modems If the network switch features an Internet connection it can be used for encrypted access to the camera footage from anywhere in the world Virtual PTZ vPTZ Panning Tilting And Zooming With No Motor Required The M15 also zooms in on detail This vPTZ function virtual Pan Tilt Zoom is a standard feature in the integrated camera software The image can be enlarged using for example the mouse wheel a joystick or a software controlled PTZ panel and you can move the view to any section of the image This provides the features of a mechanical PTZ camera without the disadvantages of maintenance and wear Simultaneous Zoomed Live Image
77. elease the L key once the camera emits a single sound boing If you use the camera s L key to load the factory default network configuration this configuration is not automatically saved in the camera s flash memory When the camera is next rebooted without using the L key the last stored network configuration will be used To permanently store the new network configuration in the camera s flash memory open Admin Menu Store The user information will not be reset if the camera is booted using the factory IP address in contrast to resetting the camera using Admin Menu Reset configura tion to the factory settings MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com First Images And The Most Important Settings 107 144 3 2 6 Starting The Camera With An Automatic IP Address DHCP If your network has a DHCP server you can start the MOBOTIX camera with DHCP support The camera automatically obtains an IP address from the DHCP server and announces the new network data Please note that this announcement can only be heard if the camera speaker has been activated l If the camera is powered on disconnect the power supply by unplugging the cor responding cables and then reconnect the power supply 2 Wait until both LEDs light up simultaneously for the first time 3 Press the R key within the next four seconds and hold it down if you need to try again go back to
78. ended to use the same wire color for for the entire MxBus system e g red blue Procedure 1 2 Open camera housing Open the camera housing as described in Section 2 2 2 Prepare the MxBus wires Remove the blue single wire plug Strip 5 mm 1 5 in of insulation from the wire ends then push each wire into one of the four holes in the single wire plug this prevents humidity from entering the camera Connect MxBus wires Push back the blue single wire plug so that you can easily attach the MxBus wires Attach the MxBus wires by firmly pushing the wires into the corresponding connectors Carefully press the single wire plug into the connector socket and twist the MxBus wire pairs If you need to remove one of the wires you need to unlock the connector by pressing on the orange colored area using a small screwdriver then pull out the wire Guide the MxBus cable out of the housing Guide the cable from the front through the cable guide in the hinge of the VarioFlex mount see figure Close camera housing Close the camera housing as described in Section 2 2 8 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com The length of the entire MxBus wiring must not exceed 50 m 55 yd Single wire plug MxBus connector 68 144 M15 Camera Manual Installation After you have connected an MxBus module you need to act
79. ens by approximately 50 The red sealing ring distinguishes this filter from other filters and the protective lens insert 1 4 2 MiniUSB Cable MiniUSB Straight Angled Order no MX CBL MU EN STR 05 2 5 straight angled MOBOTIX add on modules MX 232 IO Box ExtlO CamlO can be connected directly to the M15 with this cable which is up to five meters long 1 4 3 MiniUSB Cable To USB A Socket Order no MX CBL MU EN STR AB 05 2 5 USB based storage media for example USB hard drives can be connected directly to the M15 with this cable which is up to five meters long 1 4 4 Ethernet Patch Cable For Bayonet Catch Order no MX OPT CBL LAN 1 2 5 10 length 1 m 2 m 5 m 10 m The MOBOTIX developed special cable can be installed in a waterproof manner and has an integrated sealing gasket Every M15 ships with a 0 5 m long cable as standard which can be exchanged for a patch cable up to 10 m in length MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Available Accessories 43 144 1 4 5 NPA PoE Set Order no MX NPA PoE EU and MX NPA PoE INT Version EU and Version INT Order no MX CBL NPA BAT 2 battery cable for mobile voltage sources Thisis a multifunctional PoE injector according to the IEEE 802 3af standard with three connectors for network camera PoE device PC universal power supply unit with interchangeable adapter plugs and crossover f
80. epare the network connection The pre installed patch cable attached to the camera must be connected with the on site network cable The connection can either be established using an gt installed in wall socket with RJ45 connector or in the case of a protruding network or patch cable using the MX Patch Box In both cases the con nection is well protected and is neither accessible nor visible from the outside No screw anchors 2 Drillthe holes Use the supplied drilling template are required for for the camera found at the end of the manual wooden Sdi or if used the extended drilling template included in the MX Patch Box package Drill the holes for the supplied screw anchors Screw anchors do not have to be fitted if the surface is made of wood To secure the mount the sup 1 plied stainless steel hex head screws will be screwed directly into the surface later on You should start with a 2 mm drill bit for example drilling depth just slightly less than screw length in order to facilitate screwing in wood M15 Wall Mount 3 Attach wall seal Place the white rubber sealing ring with the groove on the edge of the wall mount 4 Connect the cable Connect the on site network cable to the camera patch cable using an adapter 9 or insert the patch cable into the RJA5 outlet Take note of the installation manual included in the Additional sealing pos sible for example with shrink tubing E package
81. eras on the market in many respects Smooth HiRes Video Streams The MI5 s optimized hardware doubles the frame rates compared to the M12 and transmits the camera s video streams smoothly even when high resolution is required Since image streams of 16 frames per second and higher are perceived as fluid video by the human eye the maximum frame rate is limited to 30 frames per second for MEGA resolution in order to provide sufficient camera processing power for other tasks High Quality Color Images Even In Low Light Conditions The more light sensitive an image sensor is the better the image quality especially when the ambient light level is low such as at dusk and in heavy rainfall The M15 offers the best MOBOTIX image quality that is currently available thanks to the light sensitivity provided by the five megapixel color sensor that is four times higher than that of the previous three megapixel color sensor Black And White Resolution Up To 3 1 Megapixels HiRes night sensor modules are also available for the M15D They can deliver black and white images up to 3 1 megapixels This means that in pixels alone images are roughly 148 larger than those delivered by the previous 1 3 megapixel sensor The images also benefit from the improved detail magnification enabled by the digital zooming of the new sensors 200 more detail compared to the old sensor More Details When Zooming The maximum zoom factor of the M15 color sensors is
82. eripheral devices LowPower mode no peripheral devices available soon 3 84 W 6 49 W Normal mode max 1 W for MxBus peripheral devices 6 49 W 12 95 W FullPower mode max 2 5 W for MxBus peripheral devices for example MX GPS Box and MX 232 IO Box to MxBus max 4 W for peripheral devices to MxBus and USB interface Caution If the total power consumption of the camera and peripheral devices exceeds the power provided by the PoE switch for the specified class the switch can disconnect the camera from the power supply In this case the camera will only be accessible again once the peripheral devices have been disconnected from the camera and the camera has been restarted The MOBOTIX factory default is PoE class 2 This default setting is usually fine and noth ing needs to be changed However the PoE power class must be changed in the browser if the higher power class 3 is required for your application fA gt MOBOTIX Q24 mx10 8 0 113 Ethernet Interface General Interface Setup 1 Select Admin Menu gt Network Setup gt Ethernet Interface for experts Ethernet Enabled p n terface Usually mare reason to disabie the Ethernet intierf i e would me io hove a running camera announce is Over Camera speaker simply press ee ae Em be disaz 6 i the Power is usualy suppled via the camera s network interface You can either ute standard Pol Power 2 Click on
83. erver simultaneously in the decentralized system Lower network bandwidth because everything is processed in the camera itself and the high resolution images therefore do not have to be constantly transmitted for analysis G3 2 C MOBOTIX system MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 21 144 22 144 M15 Camera Manual Product Overview MOBOTIX Green IP Video 1 1 5 Green IP Video The modern network based video security technology offers numerous advantages to use energy efficiently Due to the special product and system properties the decision to install MOBOTIX video systems is also a decision for Green IP Video low power consump tion and environmental friendly because of long life expectancy and minimal amount of materials involved Low Power Consumption MOBOTIX cameras are cost efficiently supplied via PoE This reduces the expenses for power and in addition saves copper and other important raw material as less power cabling is necessary Robust MOBOTIX IP66 cameras are highly robust and work without high power climate control and extra protective housing in a temperature range from 30 to 60 C 22 to 140 F Modern Integrated into the cameras are high power processors and flash storage thus making energy consuming servers and storage devices unnecessary And of course the disposal of waste later High Resolution A hem
84. formance compared to the previous M12 model The latest 5 megapixel image sensor technology used in the camera has improved the frame rate as well as the image quality for the up to 3 1 megapixel camera MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Using VarioFlex mount for installing on a wall or ceiling can be upgraded 12 144 M15 Camera Manual Product Overview images and brings a new level of detail to your zoomed images color sensor 27 Black amp White sensor 200 Thanks to the new sensors that feature a nearly four times higher light sensitivity the camera also delivers convincing color images at dusk and in heavy rainfall At night the optional black and white sensor now also provides HiRes images up to a maximum of 3 1 megapixels in size the previous M12 model offered a max of 1 3 megapixels only delivering dual images at up to six megapixels during both day and night Can Be Used Day And Night The advantage of a M15D configured as a day and night camera is primarily that it continu ously uses two sensor modules one day one night rather than relying on a mechanical filter switch which can be costly to maintain The MOBOTIX image quality is very good in poor lighting conditions as the camera uses a real infrared sensitive black and white image sensor instead of the usual color sensor with electronic color fade out whereby the infrared sensitivity is reduce
85. formatting takes considerably more time 3 Note down the characters shown in the Encryption password field or enter your own password Next click OK Proceed to Format 4 In the next dialog box enter the user thenticatien Required name and the password of a user of the WARNING You are about to erase all data on device SD Flash Card by reformatting it in admins group and click OK to confirm mxFFs mode You are therefore once again required to provide sdmin evel authentication below The MOBOTIX camera now starts format eo ting the card It takes 5 to 12 minutes to Paseword overs format an 8 GB MicroSD card if the Secure Realy proceed with formating and erasing device SD x deletion Slow option is disabled If Secure deletion Slow is enabled this may take anywhere between 3 and 14 hours Cancel Once the formatting has been completed you can activate the MicroSD card for recording see next section Make sure that you always wait until the formatting process has been completed before accessing the camera again If the Secure deletion Slow option is disabled this usually takes just a few minutes You can only access the MicroSD card once MxFFS formatting has been completed Formatting with the Secure deletion Slow option enabled takes several hours You can also use suitable applications on Windows Linux UNIX and Mac OS X systems to repartition and safely erase the MicroSD card
86. framerates SIP Client with video IP Telephony Alarm notify cam remote control Dual Modular Unique VideoMotion Multiple windows True to the original The weatherproof robust successor to our successful MOBOTIX dual camera fA Precision pixel based features interchangeable sensor modules as well as the latest MOBOTIX system technology As a result it remains totally unique in terms of performance functionality and design 22 to 140 F Weatherproof 30 to 60 C IP66 no heating necessary IEEE 802 3af PoE Network power even in winter 60 184 EN V2 07 2013 HiRes Video Innovations Robust No moving parts The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its hes fes hous decentralized concept has made high resolution video systems cost efficient MxCC MxEasy Licence free Video Management Software MOBOTIX AG gt D 67722 Langmeil Tel 49 6302 9816 103 gt Fax 49 6302 9816 190 gt sales mobotix com E o o E Q o E z 5 5
87. g a camera s microphone may be necessary in order to protect the privacy of persons at a workplace or for other reasons You can permanently and irreversibly deac tivate the microphone in the Admin Menu Loudspeaker and Microphone dialog box This deactivation occurs in the camera module itself and cannot be reversed even at the factory Deactivating the microphone will also deactivate all functions that are making use of the microphone MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Additional Notes 135 144 3 7 4 Starting The Camera With The Factory IP Address If the camera s IP address is not known you can start the camera with its factory IP address This procedure is described in detail in Section 3 2 6 Starting The Camera With An Automatic IP Address DHCP 3 7 5 Resetting The Camera To Factory Settings All settings of the MOBOTIX camera can be reset permanently to the factory default settings This makes sense if you have for example obtained a camera without any information or you would like to reset all settings after testing the camera In order to perform this procedure you need to have administrative access to the camera admins group Open Admin Menu Reset to reset the camera to factory defaults All defined users are deleted and the admin password is reset to the factory default when you reset the camera using Admin Menu Reset Use the met
88. hernet connections CATS e Outdoors Installing the camera outdoors requires special precautions and measures regarding the cables as well as lightning and surge protection 9 9 ge p f e Wire lengths The cable segments must not exceed the maximum allowed cable lengths in order to ensure proper data transfer e Avoiding induction When running data cables parallel to existing regular power lines or high voltage wires make sure you observe the minimum distances to the power cables Fire Prevention When installing the power lines to the camera make sure you always adhere to the country specific regulations for example VDE in Germany IEEE in the U S in effect on wiring and fire prevention at the site of the installation Lightning And Surge Protection More information on preventing lightning or surge damage is available from organiza tions such as the International Electrotechnical Commission www vde de or from the manufacturers of lightning and surge protectors for example Dehn S hne GmbH amp Co KG www dehn de MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com First Installation Steps 5 9 144 2 2 First Installation Steps 2 2 1 Initial Installation of the Sensor Modules bled housing as M15 Core camera The sensor modules consisting of lens carrier image sensor and lens need be ordered separately Upon delivery the sensor module
89. hod described in Section 3 2 6 Starting The Camera With An Automatic IP Address DHCP if you would like to maintain the existing users 3 7 6 Activating Event Control And Motion Detection In its default configuration the camera s event control and video motion detection features are not enabled In order to activate event controlled recording open Setup Menu General Event Settings and activate the Arming switch Another method is to click on the Arm amp Record softbutton in the browser s user interface The camera displays the motion detection window in the live image dotted frame in the center and the camera auto matically stores images as soon as the motion detection window detects movements 3 7 7 Deactivating Text And Logo Options As camera arming is deactivated in the camera s default configuration see preceding section the MOBOTIX camera only displays the text www mobotix com the time stamp and the MOBOTIX logo at the top of the image Once the camera arming has been acti vated the text at the bottom of the live image event action messaging and recording symbols will also appear You can deactivate the status bar at the bottom of the live image and the text bar in the top left hand corner by setting Text Display in the Setup Menu gt Text amp Display Settings dialog box to Off Setting Text Display to Date and Time will only display the time stamp in the live image To hide the logo in the live image open Ad
90. htened to the image edges using the panorama correction function These tilted lines are primarily caused if the camera or sensor module is tilted for example due to mounting with 15 wedges or if the image tilt is modified MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 Camera Manual Operating The Camera 44 8 2 Click the lock icon Clicking the lock once opens it lock clasp is raised The lock prevents execution of later vPTZ actions which could also unintentionally modify the view you configure This applies to all overview display modes that is also to Panorama Focus Double Panorama and Surround m MOBOTIX Admin Menu ic Setup Menu I 2 p Lock open Arm amp Record T i x T 4 Audio on J MxPEG on wi ue 3 Anew icon for processing the panorama image appears in the top left corner ofthe camera image Enlarge the image by clicking the icon once OnScreen Control appears MOBOTIX Q24 mx10 8 0 79 Livo Click the icon 4 Using the OnScreen Control visible in the live camera image you can now change the displayed live camera image as desired panning tilting zooming rotating and panorama correction See figure on the right When doing so the vPTZ func tion using the mouse or joystick is deactivated In case of a MI5D with two sensor modules click the corresponding camera image right left
91. idual exposure zones Color Bus any combination Image sensor sensitivity in lux at 1 60 5 1s mur uu um Image sensor resolution 5 MP 2592x1944 pixels Hardware Features IP protection class IP66 Temp internal DVR MB 64 Internal DVR MicroSD up to 64 GB 4 GB incl Microphone speaker X X Passive infrared sensor PIR X Internal ambient temperature sensor X X Shock detector X Power consumption in watts typical lt 5 Variable PoE class 2 3 Image Formats Frame Rates and Image Storage Max resolution per sensor 3MEGA 2048x1536 Max frame rate MxPEG max resolution 20 fps CIF images with 4 GB MicroSD DVR 250 000 VGA images with 4 GB MicroSD DVR 125 000 MEGA images with 4 GB MicroSD DVR 40 000 3MEGA images with 4 GB MicroSD DVR 20 000 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Technical Specifications 2 7 144 1 2 3 Camera Variants Software Features Camera Model M15D SEC Digital zoom continuous with panning X Motion JPEG MxPEG H 264 codecs X X X SIP video only Programmable exposure ones X Snapshot rec pre post alarm images 50 Terabyte ring buffer storage internal network X Continuous rec with sound 0 2 to 30 fps X Event recording with sound X Time and event control X Weekly schedules holidays
92. ing 3 5 6 Using A MicroSD Card In A Different MOBOTIX Camera A MicroSD card containing recorded data from a MOBOTIX camera can be inserted into any MicroSD card enabled MOBOTIX camera Once MicroSD card recording has been activated requires a reboot the new MOBOTIX camera automatically synchronizes with the card and resumes recording No data is lost in this process Make sure that you deactivate MicroSD card recording before removing the card from a MOBOTIX camera and then reboot the camera If the MicroSD card s contents are encrypted you need to enter the same password in the new camera in the Admin Menu gt Storage on External File Server Flash Device dialog box Otherwise the camera cannot access the MicroSD card 3 5 7 Limitations On Warranty When Using Flash Storage Media MOBOTIX will not assume any responsibility for flash storage devices for example MicroSD cards or connected USB storage devices delivered with or integrated into MOBOTIX cam eras The same applies to damage to flash storage devices or damage resulting from the use of devices that are not supplied by MOBOTIX MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 130 144 M15 Camera Manual Operating The Camera 3 6 Configuration In The Browser QU nm 49 hatp 10 3 0 99 gt x Google D wis Load Default View Feng v 3 6 1 Overview A MOBOTIX camera
93. inistration menu e User name admin e Password meinsm MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com First Images And The Most Important Settings 97 144 Camera Views Live Player MultiView The MOBOTIX camera automatically displays the live screen when it starts up factory default setting You can set a different start page in Admin Menu gt Language and Start Page for example the Guest screen to allow a restricted access to the live image The other available standard screens include Player playback of recorded images and video sequences and the MultiView screen displays several cameras with live or recorded images MultiView allows you to view several cameras Step MEDI im gt via a proxy camera especially useful if you lt he 08 m sen DT a want to access your cameras from outside of dT the network with reduced bandwidth and the PDA mode provides a special screen for mobile devices Click on the icon in the top right corner of the camera s user interface in the browser to find further information on the different camera screens MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Live view http camera IP gt control userimage html Player screen http lt camera IP gt control player oO ap M
94. ion Installed Image Sensors Left External sensor Cam2 Right External sensor Cam1 E Select the image sensor s Sensor Sensor currently installed Click on the Set button to accept your changes Please note that the settings of this dialog are automatically stored in the camera s permanent memory You should also open the Sensor Configuration dialog box in the following cases e Swapping the displayed camera images You wish to display the left camera image on the right and vice versa without having to replug the sensor module cables on the camera itself e Replacement of sensor modules In this case the M15D detects after startup that the sensor modules have been replaced and indicates this through an alert super imposed on the live image as well as through a system message Admin Menu lt System Messages see Section 3 4 3 Special M15 Configuration In The Browser e Adding switching on sensor modules This is where you can re enable deactivated modules e Removing switching off sensor modules This is where you can deactivate any connected modules if needed Q Q MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 124 144 M15 Camera Manual Operating The Camera More robust than hard drives Flash drives for recordings 3 5 MicroSD Card Recording 3 5 1 Introduction Flash based storage devices MicroSD cards USB sticks and solid state dr
95. ique VarioFlex mounting system supplied as standard the M15 camera can be installed quickly and easily on any wall ceiling or even a round pole of up to 18 cm in diameter when combined with the stainless steel pole mount The VarioFlex mounting system allows a wide range in both the horizontal and vertical directions rotating and tilting to enable precise adjustment to suit the area to be monitored The mount also fits directly over in wall sockets without the frame and MOBOTIX interface boxes to fully conceal the cable thus improving the security of the installation 9 G 9 9 MX 232 O Box MX GPS Box MX NPA Box MX Patch Box G 9 6 G 6 6 6 G ur RS232 signal Calculate time and Ext power supply Ext power supply inputs outputs position via GPS solar solar MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Preparing The Installation 51 144 The VarioFlex mount consists of a central joint which is directly screwed into place with the M15 housing and a wall and ceiling mount which is fastened to the central joint with just one screw In addition to being easy to install the VarioFlex mount enjoys the advantage of featuring completely concealed cabling and high impermeability to water and dust IP66 Wall and ceiling mounts are designed such that they can be installed over conventional in wall sockets without the frame or cavity sockets and conceal them
96. ispheric MOBOTIX camera with two image sensors replaces up to eight standard cameras including their consumption of energy and resources Sustainable Without mechanical components MOBOTIX cameras are maintenance free and stay fully functional even after years and are thus more sustainable compared to other systems Forward Looking Even previous camera models can be easily updated and then offer new functionalities Remote updates via the internet and the fact that the cameras are maintenance free reduce trips by car and thereby the negative effect on the environment MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 AllroundDual 2 3 144 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 24 144 M15 Camera Manual Product Overview MOBOTIX Original image L25 Super Wide Angle 12 Technical Specifications 1 2 1 M15 Lens Options Since MOBOTIX cameras are backlight proof none of the lenses requires a mechanical auto iris This makes the cameras extremely robust and maintenance free M15D SEC IT With All Sensor Modules 12 different MOBOTIX sensor modules are available for the M15D each available in day or night versions e 12 Fisheye with 180 image angle horizontal e L25 Super Wide Angle with 82 image angle horizontal e 38 Wide Angle with 54 image angle horizontal e L51 Wide Angle with
97. ivate it in the camera s browser interface Admin Menu gt Manage Hardware Expansions or Manage MxBus Modules respectively 2 2 8 Closing the Camera Housing Once you have completed the tasks in the interior of the M15 you need to reassemble the front element of the M15 Make sure that you are reconnecting all plugs as shown in the figure if you removed any of them Sensor module cable Sensor module cable right ft le 1 0 cable to front ele ment red clips Procedure l Before inserting the front element make sure that the sensor module cable of the left image sensor as seen by the camera at the inside of the screw bore see red arrow The cable must not run along the outside of the screw bore as shown in the detail image 2 Place the camera on its right side as seen by the camera as shown Push the cable of the left sensor module under the retaining lug at the screw bore red circle in detail figure MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com First Installation Steps 6 9 144 3 Pushthe front element into the housing and make sure that the sensor module cable remains under the retaining lug red circle in detail image Make sure not to squeeze or otherwise damage any of the cables when closing the camera housing 4 Continue to push the front element into the hous ing then evenly press the front element into the
98. ives do not contain any moving parts as compared to the commonly used hard drives Flash based storage devices are compact and highly resistant to moisture and vibrations They feature low energy consumption and they do not lose any data in the event of a power failure meaning that they are ideal for use with MOBOTIX cameras Number Of Write Delete Cycles Per Flash Storage Cell The number of write delete cycles of every storage cell of a flash device is limited The controller of the flash device automatically detects individual flash cells that are no longer functioning The contents of the faulty cell will then be rebuilt using a checksum and will be moved to a properly working spare cell The faulty storage cell will be marked as bad and will no longer be used No data is lost in this process In addition MOBOTIX cameras constantly monitor activated flash storage devices MOBOTIX has developed a technology to test the wear of the flash device by logging the number of write delete cycles patent pending The flash memory wear is automatically displayed in the status bar in the live camera image but it can also be viewed at any time in the Admin Menu gt Camera Status dialog box Conservative Memory Usage Thanks To MOBOTIX MxFFS File System MxFFS formatting of the MicroSD card means that the MOBOTIX camera software will use the flash device as evenly as possible thus allowing for the maximum possible number of write delete cycle
99. ix com 3 8 44 M15 Camera Manual Product Overview 1 3 3 L25 L51 Sensor Modules 3 1 p Item Number Part Name 3 1 Sensor module with affixed washer 3 2 L25 L51 lens installed 3 3 Protective glass insert with coated glass installed 3 4 Cable retainer with bayonet catch installed 3 5 Sealing plug blue small installed 3 6 Nut plastic MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Delivered Parts and Dimensions Front View 5 LEDs deactivated g E E Sensor module 2 housing a Microphone deactivated Rear View Markers for top Sensor cable con nection Sensor module housing Diam 43 mm 17 in Pressure compen sation Diam 43 mm 1 int Side View 45 mm 1 77 in gt 5 T in Sensor module weight without lock ring 111 g weight with lock ring 117 g Diam 43 mm 1 7 in 4 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 40 144 M15 Camera Manual Product Overview 1 3 4 L38 L76 L160 Sensor Modules x 4 3 Item Number Part Name 4 1 Sensor module with affixed washer 4 2 L38 L76 1160 lens installed 4 3 Protective glass insert with coated glass installed 4 4 Cable retainer with
100. ix com 102 144 M15 Camera Manual Operating The Camera Editing The Video Source List Right click this list to open a shortcut menu from which you can select all video sources or cancel the selection You can also use this method to remove from the list some or all of the video sources that you do not want to display or manage in MxControlCenter Add Video Sources Name IP Address Path Type mx10 3 30 151 11 D120 OS ERE a 24h Q mx10 8 52 T Deselect all Remove Remove all If you have cancelled the camera configuration process or need a password that differs from the camera s factory default password you can also configure the camera from the shortcut menu at a later date and enter the user name and password required for reconfiguration at that time It is also possible to open the Configure selected cameras dialog box using the shortcut menu in order to change the camera network parameters Creating A New Layout Select the camera or other video sources that you would like to display in a layout a view with a group of selected cameras in the Add video sources dialog box and then click Add selected video sources Create New Layout es You have chosen to add 2 video source s Generate new grid layout for selected video sources Name EEE Only add video sources to system do not create layout Ca ems The Create new layout dialog box is displayed If you select the Generate new grid for sele
101. l and ceiling Allen wrench 50 cm patch cable manual software 4 GB MicroSD card built in SEC IT models only am Ga MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 Camera Manual Product Overview 1 3 Delivered Parts and Dimensions 1 3 1 M15 Core Basic Module Visit www and go to Pr AllroundDua MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Delivered Parts and Dimensions Part Name Camera housing with mainboard and wall mount installed without sensor modules and front element 1 2 Front element with additional sensors installed 13 2 Transport plugs installed 1 4 Dummy module needs to be installed if only one sensor module is used in the camera Inner housing cover installed 1 6 Stainless steel Allen screw with flat head M4x8 for inner hous ing cover installed 1 7 2 Cable lock black with bayonet catch Ethernet patch cable USB one installed one supplied 1 8 2 Single wire plug blue MxBus USB installed 1 9 MicroSD card 4 GB installed 1 10 Ethernet patch cable 50 cm 19 7 in with sealing installed 11 2 Sensor module cable 15 cm 6 in installed in camera 1 12 I O cable with red clips to front element 15 cm 6 in installed 1 13 Hinged ferrite fo
102. m Network And Power Connection 8 5 144 2 7 Network And Power Connection e Power is supplied to the camera via the camera Ethernet connection patch or instal lation cable We recommend using a MOBOTIX PoE adapter or another similar high quality PoE product to loop in the power supply One camera with the PoE adapter MX NPA PoE or MX NPA Box Multiple cameras with PoE products conforming to IEEE 802 3af PoE switch gt The maximum length of the network cable for power supply over an Ethernet cable is 100 m e Make sure that you only use switches or routers that support the 10 100 Mbps network interface of the camera e We highly recommend using uninterruptible power supplies UPS to provide backup power e f you are using IEEE 802 3af or IEEE 802 3at PoE Power over Ethernet network components to supply power to MOBOTIX cameras make sure if possible that these components do not have a fan Since the power consumption of MOBOTIX cameras is very low compared to other products the reliability of the entire system is increased thus extending the life of these components Appliances with a maximum total power consumption of four watts may be con Connection of additional nected to the MxBus connector and USB connector if power is supplied to the CM ORAN ien camera using PoE class 3 f PoE Class 2 is used the power consumption of all eus USB Max ambient tempera the connected appliances should not exceed o
103. me 8 The Date amp time option will only display date and time i z a Date and Time Date amp time 3 Select format of date and time MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Virtual PTZ And Full Image Recording 5 144 3 4 3 Special M15 Configuration In The Browser M15D And Different Sensor Modules A range of combination options are provided that change 7 TUN the available display modes and configuration possibilities by using the MOBOTIX M15D with different sensor modules Because ofthis a MI5D automatically detects which sensor modules are installed and proceeds as follows e When the camera is started for the first time it detects ji 4 ihe connected sensor modules and captures their 112 sensor module L25 L38 L51 L76 data focal length day or night version L160 sensor modules e f only one sensor module is connected the camera acts as a mono camera mean ing that there is no automatic day night switching etc e f there is no change within the first 12 hours of operation the camera writes the details of these sensor modules to the camera configuration e With every restart the camera checks if the stored sensor modules are present If the sensor configuration has changed in the meantime e g because a sensor module has been exchanged fhe camera shows a corresponding message in the live
104. min Menu gt Logo Profiles and set Logo Display to Deactivated MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com You can reset spe cific parts of the configuration If the dotted rect angle in the live image is visible the camera is armed Text and logos can be also deactivated or individually configured 136 144 M15 Camera Manual Operating The Camera 3 7 8 Deactivating The Camera Reboot By factory default the MOBOTIX camera automatically reboots once a week between 3 a m and 4 a m The reason for this is that in some rare cases external influences for example radiation at high altitudes can sometimes lead to camera malfunctions The automatic reboot will refresh the camera s memory and will ensure proper operation without requiring any interaction on the part of the user If desired you can deactivate the automatic reboot of the camera in the Admin Menu Time Tasks dialog box 3 7 9 Browser Current Internet browsers Internet Explorer Mozilla Firefox Safari Google Chrome Opera etc with enabled JavaScript can display the camera s live images with their standard settings 3 7 10 Cleaning The Camera And Lens Ifthe lens becomes dirty during the installation process clean the lens using a lint free cotton cloth Make sure that the lens is still in focus after cleaning and adjust its focus if required Cleaning Domes Lenses and Filters e Alway
105. mity Declaratio DECLARATION OF CONFORMITY M15 ALLROUNDDUAL www mobot Support Libary 6 Konformitatserklarung Declaration of Conformity D claration de conformit Hersteller MOBOTIX AG Manufacturer Fabricant Produkt Netzwerk Kamera Product Network camera Produit Cam ra de r seau Typ M15 Type Type Bei bestimmungsgem fser Verwendung erf llt das bezeichnete Produkt die Bestimmungen der im Folgenden aufgef hrten Richtlinien The product identified above complies with the essential requirements of the relevant standard when used for its intended purpose Le produit d sign ci dessus est conforme aux exigences fondamentales des normes s y rapportant EMV Richtlinie 2004 108 EG EMC directive Directive CEM Angewendete harmonisierte Normen EN 55022 2010 CISPR 22 2010 Harmonised M applied EN 55024 2010 Normes harmonis e EN 61000 6 1 2007 EN 61000 6 2 2005 Weitere angewendete Normen CFR 47 FCC Part 15B Other harmonised standards applied C Tick AS NZS 3548 Autres normes harmonis es Anschrift MOBOTIX AG Address Kaiserstrasse Adresse 67722 Langmeil Germany TK Nr Phone number N de communication Fon 49 6302 9816 0 Fax 49 6302 9816 190 E Mail info mobotix com Dr Ralf Hinkel Langmeil 05 06 2013 Vorstand CEO MOBOTIX AG Ort Datum Name und Unterschrift Place amp of issue day month year Name and signature Lieu et da Nom et signature MOBOTIX AG Security Vision Sy
106. module to all MOBOTIX cameras with an MxBus or USB interface MxBus signal I O USB signal I O RS232 The maximum length of the MxBus cable diameter 0 8 mm is 50 m If the MiniUSB connection is used the maximum cable length is 5 m 1 4 10 ExtlO Expansion Module Order no MX ExtlO The device which is suitable both for on wall and in wall installations contains a powerful speaker microphone infrared motion sensor ambient temperature sensor two input and two output contacts and two illuminated keys It is ideal for door communication elevators access control systems etc The ExtlO is suitable for use as direct con nection to the M15 via a MiniUSB cable max 5 m which can be ordered separately or as a network connection via the PoE switch MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Available Accessories 45 144 1 4 11 Mx2wire Media Converter Order no MX 2wirePlus Set PW The Mx2wire system allows an Ethernet network with PoE to be set up via two wire cables which saves users from having to lay several hundred meters of Ethernet cable For example an existing two wire cable of an analog video camera can be reused to connect a high resolution and modern IP network camera Mx2wire is delivered in the standard wall outlet frame in different designs however it can also be used with the available on wall socket that is included 1 4 12
107. n Germany www mobotix com sales mobotix com Virtual PTZ And Full Image Recording 144 3 4 Virtual PTZ And Full Image Recording 3 4 1 Preparing The Virtual PTZ Function The virtual PTZ function allows you to use a mouse or joystick to continuously zoom in on images from the selected video source and virtually move the enlarged image section within the entire image sensor area Greater ease of use through a joystick Operation Using The Mouse And Scroll Wheel The vPTZ function of the M15 can be controlled in the browser using the mouse This position becomes the new image center by clicking any position on the image displayed on the monitor The image moves accordingly and the image distortion is automatically corrected The scroll wheel can be used to control the zoom function This functionality is disabled in the default settings of the camera and must therefore first be activated To do so go to Sefup Menu vPTZ Settings disable Lock Mouse Wheel Zoom click Set and then Close to save your settings You can now use the scroll wheel to zoom scroll forwards or zoom scroll backwards MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com 1127144 M15 Camera Manual Operating The Camera Virtual joystick in MxControlCenter Operation Using USB Joystick A standard USB joystick can drastically improve vPTZ operation for the user in the browser i
108. n MxEasy and in MxControlCenter however MxCC is also equipped with a virtual joystick that can be operated using the mouse Please first install the joystick on the computer according to the manufacturer s instructions In orderto use a USB joystick in the browser make sure that you have a PC with a Windows operating system and the latest version of Internet Explorer and that the ActiveX mode in the camera software browser is activated e Switch to Browser in the Quick Control EY um e Under Browser select the option A y z ActiveX in the field to the right The USB joystick can then be saca RR eee is used until the browser is closed gt Tostorethe setting permanently ActiveX must be activated in the Admin Menu To do so use Language and Start Page in the Admin Menu e Under the page options select A MOBOTIX Q24 mx10 3 0 113 Language and Start Page the ActiveX operating mode 7 LI nent ner e Store the settings permanently in the camera by clicking on Set Mun EEG adummitdcmmeuuiniimu and Close Page Design e The joystick can now be Used see eene EIGER E e SECS ue Language en E Select the angsage ty fe duiogs wd he image Pl Oows Wer trom dl Show iua or Or De 2 909w menus Tor 9 fe Live oae Varun Delaut RFigfroo Rate tor Gast Guest 9 Mame em anc dete mage reet rate on the Gor cage
109. n MxEasy for example virtual camera position zoom brightness volume microphone sensitivity image storage signal outputs can be used immediately and are stored instantly in the configuration of the corresponding camera The calendar functions integrated in the Alarm Planner provide an innovative tool for the scheduled settings of one or more cameras This tool not only controls video and sound recording based on certain time and date information but also allows features like video motion detection image brightness and the microphone to be activated deactivated based on a date and time schedule MxEasy Simple Operation Of The Most Important Camera Functions e Cameras can be installed without any knowledge of networks e Supports up 16 MOBOTIX cameras e Time or event controlled recording Time controlled motion detection image brightness and microphone For Microsoft Windows and Mac OS X 5 us Jossa F MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com MOBOTIX Software 49 144 1 5 4 MOBOTIX App Premium solution There for you whenever and wherever you need it the MOBOTIX App serves as the perfect mobile remote station that uses intelligent detailed solutions to increase security and convenience for users on a daily basis The controls are optimized for use with touchscreen devices and feature three main views Live Player Events self explanatory symbols la
110. n be downloaded and printed as PDF files from the MOBOTIX website www mobotix com in the Support gt Manuals sec tion Make sure that the cables are not bent or squashed MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 8 2 44 M15 Camera Manual Installation 6 Mount the camera Place the wall mount over the Uu wu predrilled positions in the pole mount and tighten it using the supplied M6x25 mm screws item 1 2 washers item 1 4 and M6 hex nuts item 1 5 Place the white caps on the screw heads Then aim the Screw caps for camera as described in Section 3 3 lock screws 7 Clean sensor modules Clean the protective glass and the dome of the sensor modules with a clean soft cotton cloth for optimal image results 8 Establish a connection to the camera check the image Establish a connection to the camera as described in Section 3 1 Manual and Automatic Operation Overview and the following sections The live image from the camera should be visible on the computer monitor Check image sections on the computer monitor The VarioFlex mount and wall mount must always be used for pole installation The VarioFlex ceiling mount should not be used MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Replacing The MicroSD Card 8 3 144 2 6 Replacing The MicroSD Card The camera must be t
111. n or Admin Menu gt Users and Passwords Add users and assign access rights You can add users and user groups and assign the desired rights Admin Menu Users and Passwords Admin Menu Group Access Control Lists ACL similar to a computer operating system This approach allows individual access rights to be assigned or denied to camera specific features based on the user groups Deactivate the automatic reboot In its factory state every MOBOTIX camera will automatically reboot every morning at 3 36 a m All images in the camera s storage buffer will be deleted during this reboot Images stored on external file servers internal flash storage or SD cards will NOT be affected by this reboot Make sure that you deactivate the automatic reboot if this is not desired Admin Menu Time Tasks Optimize the image settings The factory image settings of MOBOTIX cameras deliver excellent images for most application scenarios and should not be changed If you do wish to make changes your changes should be minor and gradual You should however set an image program according to the application scenario of the camera Image programs provide a quick and simple method for adjusting the camera to the application scenario as they perform several configuration steps at once Image Programs Quick Control Set the resolution of the live image By factory default all MOBOTIX cameras are delivered with an image resolution of 640 x 480 pixels You ca
112. n select the desired resolution using the Resolution Quick Control Adjust the exposure The automatic exposure control of the MOBOTIX camera uses individually configurable windows to determine the best image exposure Open the Exposure Control Quick Control and select a predefined set of exposure windows If required you can also define custom exposure windows Setup Menu Exposure Settings Activate event control and recording By factory default the MOBOTIX camera s event control is disabled Click on the Arm amp Record button to activate event control This will activate motion detection and recording Cameras with integrated flash memory MOBOTIX R models and models with SD card will use the flash memory by default to store the image and video data recording target If desired you can set additional events and adjust the settings of the recording and storage param eters Setup Menu Event Settings Setup Menu lt Recording and Admin Menu lt Recording to External File Server Flash Device MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Configuration In The Browser 3 3 144 e Set up actions messaging Upon detecting an event the MOBOTIX camera can trigger alarms These alarms can be adjusted to your needs and you can assign them to one or more events playing back an alarm sound on the camera speaker showing the visual alarm in the camera live image sending an
113. ne watt ture 50 C 1221 For information on changing the PoE class see Section 2 7 5 Variable PoE 2 7 1 Network Cabling For M15 With Patch Cables Using a patch cable and an MX Patch Box or MX NPA Box offers the following advantages e Quick installation deinstallation e No shortening of the cable in the event of multiple installation removal e Hose proof dust proof connection in accordance with IP66 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 86 144 M15 Camera Manual Installation IP addresses in the diagram are shown only as an example For the M15 you should use the blue MX NPA PoE Set or the MX NPA Box previous MOBOTIX network power acces sories such as the NPA Set Power Box and Power Rack MX NPA Set MX NPR 4 and MX NPR8 20 are not suitable for use with the M15 0 Connecting The Patch Cable To An MX Patch Box MX NPA Box Or Standard Network Port First remove the blue bayonet catch and the blue sealing 9 plug in the right hand connector on the box to establish the network connection to an MX Patch Box or MX NPA Box 2 5 Then insert the MOBOTIX patch cable into the box and secure E the cable using the bayonet catch MX Patch Box MX NPA Box More information on installing an MX Patch Boxor MX NPA G Patch Box is available at www mobotix com under Products gt I 4 e Accessories Interfa
114. network In such a case you would not be able to establish any connection to cameras in a different network or subnet without going into much further detail regarding TCP IP network configurations This is possible for example when a camera with a factory IP address is connected to a network in which a DHCP server automatically assigns the IP addresses MxEasy can automatically configure such a camera so that it is integrated into your existing network To do so you only have to select the affected camera in the list and then click Continue After a security prompt a new dialog box for configuring the selected camera is displayed The camera m12 cki with IP address 10 4 7 2047 has not been set up correctly for access from within your local network Would you like to change the network configuration of the camera now Get IP address automatically Apply to all selected cameras D Use the following IP address Cancel to If your computer automatically obtains its IP address from a DHCP server then this is certainly the best choice for that specific camera and most likely for all other cameras that have been found in a different subnet Get IP address automatically option If you have assigned a static IP address to your computer you will probably want to assign static IP addresses issued by your system administrator to every camera the Use this IP address option Normally you enter the same configuration used for the
115. network settings of your computer When you click OK the selected cameras are automatically reconfigured and they are located in the same subnet as the computer Integrating And Displaying Cameras After a camera has been reconfigured it has the status Accessible and can be integrated into MxEasy The MxEasy Assistant then displays the Define integration mode in MxEasy dialog box MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com First Images And The Most Important Settings 05 144 MEasy Wizard fs bajea Select Integration with MxEasy in order to work properly vath Mxtasy it is highly recommended to completely integrate the camera s with MxEasy Complete Integration MxCasy will reset the configuration of the camera s except for the network settings You will configure MxEasy during the following steps Limited Integration MxEasy will kccp the configuration of the camcra s You will configure MxEasy during the following steps 6 Quick Start MxEacy will keep the configuration of the camera c MxEasy will be set to default settings Here you can jump directly to the main window of MxEasy with the current live camera image by activating the option Quick Start However some required detailed configura tions may have to be made at a later time for example password protection available bandwidth For this reason we recommend activating the option Com
116. ns from smooth surfaces The filter can be used to provide better facial recognition of the people behind the windshield of a car for example Only one filter can be used per sensor module which then replaces the standard protective glass lens Procedure Note that using the polarization filter reduces the amount of light that enters the lens Position the blue lens wrench on the notches of the protective glass lens Rotate the wrench to the left until you feel a stop max 300 and then a little bit further until the protective glass lens slides out of the sensor module If required clean the inside of the filter using a clean lint free cotton cloth Place the filter on the notches of the blue lens wrench Position the filter with its clips over the two recep tacles on the sensor module red arrow on the image in the margin and firmly press onto the sensor module Rotate the glass to the right using the blue lens wrench until you feel a stop Adjust the polarization filter according to the camera s live image on the computer monitor Rotate the filter to the left using the blue lens wrench until you reach the desired setting maximum 180 To readjust the polarization filter rotate it back to the right until you feel a stop and repeat step 4 If required clean the outside of the filter using a clean lint free cotton cloth Note by approximately 50 MOBOTIX AG Security Vision Systems Made i
117. nstalled on the computer MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Manual and Automatic Operation Overview 93 144 3 1 3 Automatically Using DHCP The camera can automatically obtain its network parameters using DHCP Dynamic Host Configuration Protocol This requires the network to have a functioning DHCP server for example a DSL router with activated DHCP server and the camera must be booted using DHCP see Section 3 2 6 Starting The Camera With An Automatic IP Address DHCP The IP address automatically assigned by the DHCP server will be announced via the camera speaker as soon as the camera has booted successfully Advantages You can connect the camera directly to the target network Network parameters are automatically assigned No additional software is required You do not need to access the camera software Disadvantages The camera needs to be physically accessible as you need to press a key on the camera housing to boot it using DHCP Requires a running DHCP server on the network MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 94 144 M15 Camera Manual Operating The Camera Pressing the L key see Section 2 7 6 prompts the camera to announce its current IP address over the speaker Entry in Subnet mask field 255 0 0 0 3 2 First Images And The Most Impor
118. o Integrated 4 GB MicroSD card 6 megapixels also at night expandable up to 64 GB Q p 9 A A i b A 1 rd p h High frame rates up to Shock detector 30 fps Mega MiniUSB port for external Variable PoE class expansions 1 50 95 6 5 0 9 MxBus port for MOBOTIX MxActivitySensor detects add on modules movement and the direction of movement One sensor module mono camera Two sensor modules dual camera sys system with Day or Night image sen tem with any combination of Day Night sor and images up to 3MEGA image sensors and dual images with up to 6MEGA Q MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 8 144 M15 Camera Manual FOREWORD Dear MOBOTIX customer Congratulations on your decision to purchase the M15 the powerful successor to the original MOBOTIX MI M10 MI2 proven one hundred thousand times This weatherproof IP66 versatile all round solution Made in Germany represents an important milestone in the successful history of MOBOTIX products As decentralized complete video systems MOBOTIX cameras have much more to offer than conventional network cameras The M15 features integrated environment sensors PIR outside temperature motion sensor speaker and microphone for two way video communication based on the SIP standard long term memory free video management software and a preassem
119. oducts Depending on national laws and the installation location of the M15 the recording of video and sound data may be subject to special documentation or it may be prohibited MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Additional Notes 137 144 All users of MOBOTIX products are therefore required to familiarize themselves with all valid regulations and comply with these laws MOBOTIX AG is not liable for any illegal use of MOBOTIX products Network security MOBOTIX products include all of the necessary configuration options for operation in Ethernet networks in compliance with data protection laws The operator is responsible for the data protection concept across the entire system The basic settings required to prevent misuse can be configured in the software and are password protected This prevents unauthorized parties from accessing these settings Never remove domes lens covers The MOBOTIX cameras S15D and S15M should never be operated without their preinstalled transparent domes sensor modules SI5D and housing S15M or protective lens covers sensor modules S15D The camera is no longer weatherproof when operated without the domes or protective lens covers The exposed metal ring around the lens can become extremely hot when the exterior temperature is high Touching this ring can cause burns Only exchange sensor modules when powered off Make sure that the camera s p
120. of the Sensor Modules MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 AllroundDual 1 1 2 Hemispheric Sensor Module Equipped with the hemispheric L12 sensor module day or night an entire room can be ideally monitored using just one M15 which replaces the time consuming and expensive installation of several standard cameras The overview image provided by a single M15 which may be tailored in a number of ways according to specific user requirements minimizes the system costs by reducing the wiring complexity emergency power require ments and number of recording devices required High Resolution Panorama When several cameras are monitoring a single room it is difficult to understand the room layout due to the different viewing directions of each individual camera This makes it hard to comprehend the overall setting The panorama function of the M15 with the L12 sensor module delivers a widescreen corrected image of a high resolution 180 allround view Panorama image at 0 6 megapixels 1280x480 pixels Optimizing The Panorama Image The factory setting of an M15 with an L12 lens is a high resolution panorama image in which parts of the protective cover of the housing are still visible in the upper right and left corners of the image In order to hide the protective cover often all that is required is the panorama correction feature that is integrated into th
121. of the live image stream which may drop by around 10 to 30 percent We therefore recommend reducing the frame rate for storage as much as possible to affect the live image stream as little as possible Full image recording off The event that triggered a video motion VideoMotion VM window may not be in the recorded sequences because the window was not displayed at the time MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 114 144 M15 Camera Manual Operating The Camera Activate Deactivate Full Image Recording In The Browser To configure this feature open the Setup Menu gt Event Control gt Recording dialog box and activate or deactivate the Full Image Recording option 4 gt MOBOTIX Q24 mx10 8 0 113 Recording General Settings Value Explanation Adis Arm Recording g Enable L Controls camera recording Enabie activate Recording Off deactivate Recording SI Recording armed by signal input CS Recording armed by custom signal as defined in Genera Event Settings From Master copies Recording arming state from master camera 1 Time Table Profile no time table Time table profile for time controtied recording Time Tables Digital Signing off 9 Digital Signing Digitally sign the recorded image files using the X 508 certificate of the web server Manage 509 certificates of the web server Recording Status Symbol n Activate Recording
122. onfigure Selected Camera xl This computer accesses the following subnet s 10 0 0 0 192 168 0 32 Get IP address automatically DHCP Use the following IP address range IP address start IP address end Subnet mask Standard gateway Store configuration in camera Cancel Make sure that the Store configuration in the camera checkbox is selected This setting ensures that the cameras are displayed with the correct network settings even after they have been rebooted Click OK to close the dialog box Wait until MxControlCenter has changed the network settings and rebooted the cameras The status of the reconfigured camera changes from gt Different subnet to OK Defining Additional Video Sources In addition to the MOBOTIX cameras that are found automatically you can also manually add video sources to the list of video sources for MxControlCenter e Camera Here you can enter the known IP address or DNS name of a MOBOTIX camera or a third party IP camera if it was not found by the automatic search feature e MxPEG clip Adds an MxPEG video clip previously recorded by a MOBOTIX camera as a video source e Recording path Adds the path of an external file server where a MOBOTIX camera has recorded audio video data The videos or images recorded at that location can now be played back using the Player or Video Search MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobot
123. or dance with all legal requirements and regulations or deposit these products at a munic ipal collection center MOBOTIX products may not be disposed of with household waste Ifthe product contains a battery please dispose of the battery separately the correspond ing product manuals contain specific directions if the product contains a battery 3 7 15 Disclaimer MOBOTIX AG does not assume any liability for damage that is the result of improper use of its products or failure to comply with the operating manuals or the applicable rules and regula tions Our General Terms and Conditions apply You can download the current version at www mobotix com using the 605 link at the bottom of each page O Q MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Additional Notes Notes MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 Camera Manual Notes MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Notes MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 Camera Manual Declaration of Confor
124. ork cameras provides a user friendly user interface and camera image display convenient video search functions effective alarm handling automatic camera integra tion video storage on file servers as well as useful configuration and update wizards MxControlCenter Professional Video Management Several hundred cam eras can be managed Proven worldwide in the most demanding video applications thousands of times over EE dard PC Unlimited number of users and cameras no license fees Individual user interface adaptable to each individual user Simple installation and complete use on any standard PC Convenient layout editor for integrating real floor plans Integration of conventional network and analog cameras as well For Microsoft Windows Download free of charge from www mobotix com No license fees Free updates MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 48 144 M15 Camera Manual Product Overview Suitable for up to 16 MOBOTIX cameras Download free of charge from www mobotix com No license fees Free updates 1 5 3 MxEasy MxEasy makes it simple to operate the most important functions of the camera thanks to its intuitive user interface and represents a new approach to viewing and controlling MOBOTIX cameras The clear design allows you to manage up to 16 cameras and the application can show up to four cameras at the same time All settings selected i
125. ower supply has been disconnected before attempting to exchange any sensor modules 3 7 12 Online Help In The Browser For more information see the News and Functional Overview pages in the online help of the camera s browser interface Click on the icon to open the camera s online help Furthermore detailed information on the camera and its current configuration is displayed in the Camera Status dialog box when you click on the icon MOBOTIX Q24 mx10 8 0 79 Live 16 fps c Display Mode B Admin Menu TT I Setup Menu Arm amp Record Audio on MxPEG on m TT TV MxPEG off TT NIE uc Event LEDs Blink Select iz o 3 7 13 RoHS Declaration The products of MOBOTIX AG are in full compliance with Art 5 of the German Electrical and Electronic Equipment Act and the E U Directive 2002 95 EC on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment RoHS as far as they are subject to these regulations You can find the MOBOTIX RoHS Declaration under www mobotix com Support gt Spec Sheets MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 138 144 M15 Camera Manual Operating The Camera 3 7 14 Disposal Electrical and electronic products contain many reusable materials For this reason we would ask that you dispose of MOBOTIX products at the end of their service life in acc
126. party IP cameras file server paths MxPEG clips and analog cameras connected via MxServer for example analog dome cameras These video sources are not found automatically and need to be added manually MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Automated search for MOBOTIX cameras 100 144 M15 Camera Manual Operating The Camera Cameras Are Found But Are Located In A Different Subnet The symbols in the first column and the legend in the dialog box indicate whether you can access a particular camera directly from the MxControlCenter which is the case for all cameras designated with 9 OK Cameras designated with _ different subnet are located in a different subnet This usually applies to new cameras or cameras that have been reset to their factory settings MxControlCenter finds all MOBOTIX cameras even when the computer and the cameras are not located in the same subnet Once you have marked all of the desired video sources in the list with OK you can now select the ones that you wish to display and manage in MxControlCenter The live image is automatically displayed in the preview window when a camera is selected to help you identify the cameras For cameras marked with Different subnet or if you want to add additional video sources follow the instructions in the following sections You can also display the selected cameras directly in a layout For mo
127. pixels Image analysis Recording the cameras not to evaluate and record video This means that you do not have to rely on expensive overloaded video management software as most of the important functions that require a large amount of processing power are integrated into the MOBOTIX cameras themselves MOBOTIX Kamera Integrated sensors enable MOBOTIX cameras such as the M15 to automatically detect when an event has occurred If necessary the cameras will respond immediately with an alarm sound and will establish a direct video and sound connection to a control room M15 IT SEC models utilize MxActivitySensor to detect the movement of people and objects and their direction of movement as standard The MxActivitySensor delivers reliable results particularly in outdoor area applications in contrast to video motion detection that con tinues to be available and that registers even the smallest of image changes in defined video motion windows In the defined monitored area full image or section the camera distinguishes between the continuous movements of vehicles persons or objects that trigger an alarm and movements that do not set off an alarm such as shadows changing light conditions heavy rain or trees swaying in the wind The M15 is also equipped with a shock detector as standard for all IT and SEC models For example if the camera receives a blow to the housing it can simultaneously take a video of the offender trigger a sound ala
128. plete integration and complete the remaining dialog boxes of the MxEasy Assistant until the main window appears After you are done with the MxEasy Assistant the application s main window appears and displays the first camera Main window with dual image display of a M15 telephoto lens and wide angle For more information see the MxEasy User Manual which can be downloaded as a PDF file from the MOBOTIX website www mobotix com gt Support gt Manuals MOBOTIX AG Security Vision Systems Made in Germany www mobotix com salesemobotix com 106 144 M15 Camera Manual Operating The Camera Passwords and cam era settings will not be changed Make sure you store the factory default network configuration to the permanent flash memory 3 2 5 Starting The Camera With The Factory IP Address Under certain circumstances you may have to reset the camera to its factory IP address This could be the case for example if the IP address has been lost or the camera does not respond to the last known IP address Proceed as follows to start up the camera with its factory IP address 1 If the camera is powered on disconnect the power supply by unplugging the cor responding cables and then reconnect the power supply Wait until both LEDs light up simultaneously for the first time Press the L key within the next four seconds and hold it down if you need to try again go back to step 1 Q Q 4 Only r
129. possible MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 44 144 M15 Camera Manual Product Overview 1 4 8 MX GPS Box Order no MX OPT GPS1 EXT This box primarily serves as a high precision time source for systems without an Internet connection The IT and huc E SEC models additionally provide triggering of GPS based events reaching or moving away from a specified posi tion exceeding or not reaching a specified speed The MX GPS Box can be connected as an add on module to all MOBOTIX cameras with an MxBus interface The MX GPS Box has the same compact exterior housing as the MX Patch Box and the MX NPA Box IP66 protection class 30 C to 60 C 22 F to 120 F Note that this box should not be installed below other wall mounted units It should be installed on the exterior of the building with a large section of open sky above it which ensures the best possible reception from GPS satellites and thereby the highest possible accuracy of the received GPS data The maximum length of the MxBus cable diameter 0 8 mm is 50 m 1 4 9 MX 232 IO Box Order no MX OPT RS1 EXT e Or This box provides the signal inputs and outputs as well as the RS232 serial interface of a MOBOTIX camera replaces the connections that were handled on the older camera models via a D Sub 15 HD connector The MX 232 IO Box can be connected as an add on
130. ption And Authentication All video data stored on the MicroSD card is encrypted to ensure security at all times The password for this is defined during the card s formatting procedure and needs to be entered for authentication whenever the recordings are accessed see next section MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Activate recording Admin Menu Storage on External File Server Flash Device 128 144 M15 Camera Manual Operating The Camera 3 5 4 Accessing Data on the MicroSD Card The following options facilitate access to the stored image and video sequences on a MicroSD card n the web browser Play back the recorded event images without sound directly from the MicroSD card using the Playback view of the camera software e n MxEasy Play back the recorded video sequences with sound by accessing the MicroSD card in the MOBOTIX camera via the camera e In MxControlCenter Play back the recorded video sequences with sound by access ing the MicroSD card in the MOBOTIX camera via the camera or by directly accessing the MicroSD card via a card reader connected to the computer Access the card by setting the MicroSD card s drive volume as a Directory in MxControlCenter If the recordings stored on the MicroSD card were encrypted you need to enter the password used for the encryption before you can access the data If this is the case both MxControlCenter and M
131. r PIR sensor LEDs Buttons Connections On The MOBOTIX M15 The MOBOTIX M15 provides the following connections that can be accessed once you have opened the housing see Section 2 2 2 Opening the Camera Housing MxBus Ethernet patch cable MiniUSB Sensor module cable 1 0 cable for front element red clips and seals MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Delivered Parts and Dimensions For connections on the M15 shown above always use the corresponding MOBOTIX cables with seal e Ethernet patch cable MX OPT CBL LAN 1 2 5 10 e MiniUSB straight angled MX CBL MU EN STR 05 2 5 e MiniUSB to USB A straight to USB port MX CBL MU EN STR AB 05 2 5 MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 Camera Manual Product Overview Dimensions Of The M15 With Wall Mount 158 mm 6 22 in d 106 mm 4 17 in 4 Al o 5 E eo E N t a E o 239 mm 9 41 in 4 4 A Py E gt md e ATS e E E 5 N E E wu e2 y y MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Delivered Parts and Dimensions Dimensions Of The M15 With Ceiling Mount 158 mm 6 22 in gt
132. r Ethernet cable installed 1 14 2 Hinged ferrite for sensor module cable installed 1 15 2 Rubber plug for covering mounting screws installed 1 16 9 Stainless steel Allen screw M6x30 installed 1 17 3 Stainless steel washer 6 4 mm installed 1 18 Stainless steel spring washer 6 4 mm wall ceiling mount installed 1 19 Stainless steel lock nut M6 wall ceiling mount installed Mounting Parts Item Number Part Name M 1 4 Stainless steel washers diam 6 4 mm M 2 4 8 mm screw anchors M 3 4 Stainless steel wood screws with hex head 6x50 mm M 4 Allen wrench 2 5 mm M 5 Allen wrench 5 mm M 6 Lens wrench L12 lens dome M 7 Module wrench sensor module glass filter insert lenses M 8 Rubber sealing ring for wall or ceiling mount white M 9 Ceiling mount for VarioFlex mount M 10 Protective screw caps white M TI Security clip for sensor and dummy modules red MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 32 144 M15 Camera Manual Product Overview LED default settings 1 Power on Error flashes 2 Recording flashes To do so use a paper clip but avoid using sharp or pointed objects Design Of The MOBOTIX M15 The basic module of the MOBOTIX M15D consists of a housing with VarioFlex mount for wall or ceiling and the front element VarioFlex wall mount Camera housing Sensor modules Microphone Ext temperature senso
133. r more information on this topic refer to the online help for the specific dialog boxes The More and Less buttons When opening some of the camera dialog boxes the camera only shows the most important parameters These dialog boxes have a More button in the bottom right hand corner Click it to display additional options If all options are displayed click on the Less button to hide the additional options MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com User name admin password meinsm Admin Menu Setup Menu Make sure to perma nently store changed parameters Automatic time syn chronization using a time server More Display advanced features Less Hide advanced features 132 144 M15 Camera Manual Operating The Camera 3 6 2 General Browser Settings Run the Quick Installation After booting the MOBOTIX camera for the first time accessing the administration menu the Admin Menu button will automatically start the Quick Installation The Quick Installation assistant helps you in setting the most important parameters of the camera For security reasons you should set your own administrator password and disable public access to the camera Disable public access Guest users are only allowed to access the Guest screen of the camera without entering a password If this is not required you should deac tivate public access Admin Menu gt Quick Installatio
134. rages 126 144 M15 Camera Manual Operating The Camera Format SD card Admin Menu gt Storage on External File Server Flash Device The Secure deletion Slow option takes several hours You can also use suitable applications on Windows Linux UNIX and Mac OS X systems to repartition and safely erase the SD card 3 5 2 Formatting The MicroSD Card Before a MOBOTIX camera can store image and video sequences on a MicroSD card it needs to be formatted as MxFFS MicroSD cards delivered with MOBOTIX cameras are already MxFFS formatted The following steps are necessary to format a storage device Admin Menu gt Storage on External File Server Flash Device 1 Make sure that there is a MicroSD card in the card slot of the MOBOTIX camera 2 Click Format in the SD Memory Card line Formatter Wizard MxFFS Volume Partitioning Please indicate what you want to store on MxFFS storage device SD Flash Card The total device size is 3 69 GB V Event Recording Volume Note The Secure deletion Slow option will ensure that any data on the MicroSD secure deletion mode siow To encrypt an MxFFS storage volume an encryption keyword is required An ca rd is overwritten completely SO that the empty keyword disables encryption Changing the keyword later on will prohibit access to previously encrypted recordings data cannot be recovered in any way Data Encryption Key However keep in mind that this kind of safe
135. re information see section Creating A New Layout Reconfiguring Cameras In A Different Subnet If one or more MOBOTIX cameras are displayed with the status Different subnet for example cameras with a factory IP address MxControlCenter automatically offers to configure the network settings of the cameras In this case the application displays the dialog box shown here after you have clicked on the Add selected video sources button Click Yes to configure the cameras to the subnet of your computer MxControlCenter es One or more of the selected cameras are in a different subnet Would you like to reconfigure them now A DHCP server automatically assigns IP addresses for network devices in most networks so that you can automatically select the default setting Get IP address automatically DHCP in the Configure selected cameras dialog box MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com First Images And The Most Important Settings 101 144 Activate the Use this IP address this range option if the IP address of a particular camera must be assigned manually for networks with static IP addresses Obtain the assigned IP address subnet mask and standard gateway from your network administrator and enter the data All you have to do is enter the range of IP addresses that includes the addresses of all of these cameras to reconfigure multiple cameras at the same time C
136. rge softbuttons multifunctional sliders developed by MOBOTIX as well as simple gestures like swipe and tap making it easy for newcomers and older users to work with professional security equipment In addition using mobile devices to operate the various functions such as door opening activating the voice mailbox switching the door bell off at night and switching a light on off creates added value in the form of greater convenience and security in every day life MOBOTIX App Mobile Remote Station For MOBOTIX Cameras And Door Stations Bandwidth optimized remote access via WLAN Wi Fi or the Internet Live images and recordings in the best MOBOTIX HiRes quality Two way communication door opening and video mailbox access Doorbell and alarm notifications protection of privacy Convenient search functions playback of external MxPEG videos Grouping of cameras and filtering of events Free from the App Store for the iPad iPad mini iPhone and iPod touch MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com P 4 Available the App Store Free download from the App Store No license fees Free updates 50 144 M15 Camera Manual Installation 2 INSTALLATION The MOBOTIX M15 has been designed to be mounted on walls and ceilings It can also be installed on a mounting pole using the appropriate MOBOTIX accessories The different installation options are described in
137. rger changes in one dialog box without resetting the complete configuration you can use the Default button at the bottom of the dialog box to reset only this dialog box s settings to the factory set tings If you would like to reset all image settings you can do so using the Manage Settings Restore Image Settings Quick Control in the live image of the camera Storing changes permanently Once you have finished configuring the camera you should always store the settings in the camera s permanent memory You can do so in each dialog box clicking on the Set button at the bottom of each dialog box will temporarily implement the change when you click Close you will be asked to store the complete configuration in the camera s permanent memory or in the Admin Menu Admin Menu Store current configuration into flash memory The Configuration section of the Admin Menu provides more functions for storing copying and managing camera settings For more information on this topic refer to the online help for the specific dialog boxes Time tasks and time synchronization Apart from a multitude of possibilities for controlling the camera using time time tables holiday and vacation scheduled tasks etc the camera can also synchronize its internal clock This allows you to manually synchronize the camera with a computer or automatically using a time server or another MOBOTIX camera The camera can use either NTP servers or Time Protocol servers Fo
138. rm and notify the security company by a SIP call Due to the build quality and absence of moving parts MOBOTIX cameras are extremely tough This typically allows them to stay fully operational even when they are subject to strong vibrations All MOBOTIX cameras are backlight proof and are not adversely affected by the glare from direct sunlight They deliver meaningful detailed images at all times as the camera software supports easy programming of independent exposure windows making them ideal for rooms with large glass fronts MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 AllroundDual MOBOTIX In the event of an alarm M15 cameras can also record lip synchronous audio The cameras therefore play an important role in analyzing and clarifying a situation Thanks to an integrated speaker and microphone each individual camera can also be used for bidirectional communication two way video communication so you can easily use the MOBOTIX App with your iPhone or iPad on the road The decentralized MOBOTIX video solutions are superior to traditional systems in all major aspects They are also considerably cheaper to operate as they require e Fewer cameras due to the more accurate detail of panorama images with mega pixel technology e Fewer recording devices because ten times the standard number of cameras can be used to record high resolution HDTV video with sound on one computer s
139. rocedure l Position the blue lens wrench on the notches of the sensor module Rotate the wrench to the left until you feel a stop max 300 and then a little bit further until the protective glass lens slides out of the sensor module 2 Adjust the image sharpness according to the camera s live image on the computer monitor To do so position the black module wrench with the ring pattern side on the lens and carefully rotate to the right or left Do not turn the lens too far or with force to avoid damaging the image sensor 3 If required clean the inside of the protective glass lens using a clean lint free cotton cloth 4 Place the protective glass lens on the notches of the blue lens wrench 5 Position the protective glass lens with its clips Ss over the two receptacles on the sensor module red arrow on the image in the margin and firmly 2 press onto the sensor module Rotate the glass to the right using the blue lens wrench until you x feel a stop o 6 If required clean the outside of the protective glass lens using a clean lint free cotton cloth MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 110 144 M15 Camera Manual Operating The Camera 6 e 3 3 3 Inserting A Filter MOBOTIX offers a polarization filter in its range of accessory products for all sensor mod ules except the L12 The polarization filter prevents unwanted reflectio
140. s This also means that all storage cells of the flash device will be written and deleted with the same frequency if possible MOBOTIX technology increases the life of the flash device considerably and also improves the security and the reliability of the storage process Storage Requirements And Life Expectancy Of MicroSD Cards The life expectancy of a MicroSD card increases proportionally to the storage capacity since the camera software will execute fewer write delete cycles on each storage cell The first deletion will begin once the SD card has been filled to capacity first full cycle MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com MicroSD Card Recording 125 144 32 GB MicroSD Card Storage Requirements 6 fps CIF 6 fps VGA MEGA 1 fps QXGA M JPEG M JPEG MxPEG M JPEG M JPEG File size single image 15 kB 45 kB 120 kB 240 kB storage required per 90 kB 270 kB 75kB 120 kB 240 kB second Storage required per 24 amp Gp 23 5 GB 6 5 GB 10 4 GB 20 8 GB hours Time for one full cycle 4 days 1 3 days 4 8 days 3 days 1 5 days 4 GB MicroSD Card Storage Requirements 6 fps CIF 6 fps VGA lfps MEGA 1105 QXGA M JPEG M JPEG MxPEG M JPEG M JPEG File size single image 15 kB 45 kB 120 kB 240 kB orage red red pier 90 kB 270 kB 75 kB 120 kB 240 kB second ca required per24 ly aep 23 5 GB 6 5 GB
141. s in VGA resolution to pan tilt and zoom in EN full image the live image while the camera is for example recording full images at 1 fps in MEGA Original camera image or QXGA resolution without distortion or image correction In MxEasy and MxControlCenter the recorded full images may be prepared for the user with the vPTZ functions for example panning and zooming in on an image detail such as a doorway If full image recording is not activated only the last displayed live image will be saved save what is seen The main benefit of live image storage is to ensure that the full power of the camera processor is used for live image correction and maximum frame rates The main advantage of full image recording lies in the special functionality of the M15 in that it can always maintain availability of a maximum size full image for later investigation despite vPTZ actions carried out on the live image The mechanical limitations of motor driven PTZ cameras mean that they simply cannot provide this unique advantage to the user Post event search in the full image If you are using full image recording on M15 cameras you should use at least MEGA resolution when storing This will facilitate later searches in MxControlCenter or MxEasy The advanced distortion correction features require this function to deliver satisfactory image quality Full image recording on Due to the increased processing time full image recording reduces the data rate
142. s mount and unmount the dome using the blue lens wrench M 6 in order to protect it from being scratched and from getting dirty e Use the wide side of the black module wrench M 7 for mounting unmounting lens protection covers filters The slim side of the wrench is used to adjust the focal length sharpness of all lenses except L12 e You should clean the dome at regular intervals Always use a soft lint free cotton cloth for this purpose e f the dirt is more persistent add a mild alcohol free detergent without abrasive particles e Make sure you instruct cleaning personnel on how to clean the camera 3 7 11 Safety Warnings Electrical surges A range of measures are used to protect MOBOTIX cameras against the effects of small electrical surges These measures however cannot prevent the camera from being damaged when stronger electrical surges occur Particular care should be taken when installing the camera outside to ensure proper protection against lightning as this also protects the building and the entire network infrastructure Electrical installation Electrical systems and equipment may only be set up changed and maintained by a qualified electrician or under the direction and supervision of a qualified electrician in accordance with the appropriate electrical guidelines Legal aspects of video and sound recording You must comply with all data protection regulations for video and sound monitoring when using MOBOTIX pr
143. set an area click its center point again During panorama correction clicking between the two trapezoid symbols straightens the left or right tilting lines which are best visible at the edges of the image section MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com Depending on the instal lation position ceiling wall floor panorama correction and image tilt correction may not be available Bring columns together at the top neces sary to correct the example on the left Bring columns together at the bottom 120 144 M15 Camera Manual Operating The Camera For vPTZ use and the configuration of a USB joystick see Section 3 4 1 Ceiling Mounted Set North User Defined North Direction Once a sensor module M15D or entire camera M15D is installed on a ceiling you need to specify its North direction This is not the true direction of North but rather the main line of sight or the focus of the camera or sensor module It serves as a reference for the North direction in the Surround and Double Panorama display modes the Ceiling option was already selected in the Installation Type Quick Control l In the case of a double image click the corresponding sensor module camera image and select the Normal option from the Display Mode Quick Control MOBOTIX 7pm 5 Can fig 1680 E8 zeige Modus vPT
144. sing the pole mount which is available for the M15 as an accessory and is almost indestructible MX MH SecureFlex ESWS This pole mount is made from rust proof stainless steel with a white coating and is used in combination with the pre installed VarioFlex mount supplied as standard with the wall mount Poles with a diameter between 60 and 180 mm can be used It is particularly advisable to use cavity metal poles in which the network cable is not visible and can be protected from attacks For more detailed information on the installation process see section 2 2 The drilling templates are at the end of the manual 2 1 2 Installing The Camera With Hemispheric Sensor Modules The camera must be correctly positioned on the wall or ceiling in order to be able to use the high resolution hemispheric image display options of the M15 with L12 sensor module s The entire hemisphere of the room in front of the camera is then effectively monitored High Resolution Panorama Images The M15 with L12 sensor module s is primarily suited to providing an excellent overview in the form of a high resolution panorama image and less suitable for more exact details For active operation the camera should be installed at an out of direct reach height ranging from 2 5 m to 3 5 m People for example may be identified very well at distances of up to 1 5 m and with sufficient detail at up to 3 m Objects can be detected even at distances of 5 m and more from the
145. special advantages when a security camera looks like the real thing thanks to its unique striking product design which has stood for leading video technology and image quality for many years This is because potential criminals have developed an eye for spotting high resolution MOBOTIX cameras and will shy away from them when they see one Even they know these kinds of video cameras can record all activities with an image quality high enough to be used as evidence and criminals would rather abandon these attempts and concentrate on less secure prospects Modular System Setup A M15 camera consists of three main components l Housing with integrated camera electronics flash memory external ports Ethernet MxBus MiniUSB and pre installed VarioFlex mount for wall or ceiling mounting 2 Front element to hold one or two sensor modules with microphone speaker passive infrared sensor PIR outside temperature sensor and status LEDs 3 Oneor two sensor modules with lens image sensor microphone and status LEDs microphone and status LEDs are deactivated if attached to a M15 The housing with VarioFlex mount connection cable for sensor modules and network and the front element are components of the M15 Core basic module as standard The sensor modules may be ordered separately and combined freely as desired for example Day Night telephoto wide angle The system s modular design ensures a high level of flexibility and ease of repair for ex
146. stems Made in Germany www mobotix com sales mobotix com Manufacturer 3 144 MOBOTIX The HiRes Video Company Security Vision Systems MOBOTIX To demonstrate our confidence in the quality of our products MOBOTIX cameras have been used to capture all images that appear in this manual Manufacturer Executive Board MOBOTIX AG Dr Ralf Hinkel Kaiserstrasse 67722 Langmeil Germany Registration Office Kaiserslautern Local Court Germany Registration Number HRB 3724 Tel 49 6302 9816 103 Tax Code 44 676 0700 4 Fax 49 6302 9816 190 Tax Office Worms Kirchheimbolanden Germany http www mobotix com VAT ID sales mobotix com DE202203501 You can find the latest version of this document at www mobotix comin the Support section CE Technical specifications subject to change without notice MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com M15 Camera Manual The HiRes Video Company MO BOTIX HiRes 6 Megapixels 4096 x 1536 Software zoom Skyline Format free Each image format freely definable 30 Frames s VGA 640 x 480 30 F s Mega Virtual PTZ Digital pan tilt zoom Backlight Safe using CMOS without mechanical iris Internal DVR Internal via Flash external via Network Win Lin Mac Recording via Network on PC up to 4 Terabyte Microphone amp speaker Audio bi directional via IP variable
147. step 1 Q Q 4 Only release the R key once the camera emits a double sound boing boing Starting the camera with an automatic IP address DHCP is only temporary The network configuration of the camera can be permanently set to DHCP under Admin Menu gt Ethernet Interface Make sure that the network has a functioning DHCP server when starting the camera In case of anerror with DHCP support If this is not the case the camera cannot obtain a valid IP address the camera uses its last IP address and will use its last IP address You should also make sure that the cameras always obtain the same IP addresses by permanently assigning the MAC addresses of the cameras to the desired IP addresses MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com 108 144 M15 Camera Manual Operating The Camera Section 3 5 provides more details and informa tion on the functionality of the OnScreen Control lt Me dieu S r Correcting the image horizon ELE Rotate image to the left SIG Rotate image to the right 3 3 Adjusting Camera Lens Focus And Installing A Filter 3 3 1 Adjusting The Camera l The live image from the camera is displayed on the computer monitor 2 Loosen the screws on the VarioFlex mount using the supplied Allen wrench so that you can easily turn and tilt the camera 3 Display the desired camera section on the
148. t Panorama and Surround respectively Every other display mode can be operated in the same way MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Virtual PTZ And Full Image Recording 7 144 Wall Mounted Setting And dini the Standard View Panorama 6 gt md Dm l I bz is Camera live image with Fief R P 1 p panorama correction Y High resolution 180 panorama 1 Inthe Display Mode Quick Control select the Panorama option Examine the image that is now displayed If the section meets your expectations no further adjustment is necessary and panorama configuration is complete To change the image section to meet your specific expectations continue with step 2 Camera live image with E a outMOBOTIX panorama eevee Installation aie correction with Quick p Menu d S E D inscr o Controls visible B astomoaus Uoppel Panorama E Panorama Fokus Belichtungssteuerung Farbs ttigung Gegenlichtkorrektur rte JPFC Qualirar Schartstellhil e The currently visible image section may differ from the desired image section due to the installation position or any accessories in use for example However it is not necessary to physically move the camera as in this case the browser alone can be used to adjust the visible panorama image by zooming panning and tilting Tilted vertical lines may also be optically straig
149. table adapter for example in an existing cavity socket Drill the holes Use the supplied drilling template for the camera found at the end of the manual Drill 106 5 the holes for the supplied screw anchors Screw anchors do not have to be fitted if the surface is 8 made of wood To secure the mount the supplied stainless steel hex head screws will be screwed _ directly into the surface later on You should start with a 2 mm drill bit for example drilling depth just slightly less than screw length in order to facilitate 4 MP li QJ CC JI screwing in wood MNA BENE A mM Attach ceiling seal Place the white rubber seal with the groove on the edge of the ceiling mount via connector Make sure that the cable is not bent or squashed MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Mounting The Camera With Ceiling Mount 77 144 6 Mount the camera Place the ceiling mount over the drill holes use the four screws each with a washer and tighten them using the appropriate screwdriver Do not overtighten the screws as this may damage the plastic mount Check that the screws are securely in place and place the white caps on the screw heads Then aim the camera as described in Section 2 7 Screw caps for lock screws 7 Clean sensor modules Clean the protective glass and the dome of the sensor modules
150. tant Settings Once the MOBOTIX camera has been connected to the network you need to set up the camera s network interface accordingly This step involves setting up and checking the network parameters of the camera If your network is already using an IP address in the 10 x x x range with a 255 0 0 0 network mask you do not need to change the camera s network parameters You can access the camera directly see Section 3 2 2 If your network or computer does not use an IP address in the 10 x x x range for example in the 192 or 172 ranges you should follow one of the following methods for changing the camera s network parameters e Manual setup see Section 3 2 1 e Automatic setup using MxControlCenter or MxEasy see Section 3 2 3 and Section 3 2 4 We will use a camera with the factory address 10 8 0 99 in the following exam ples Replace this IP address with the IP address of your camera You will find the IP address of your camera on a small sticker on the camera Make sure that the IP addresses used in the following examples are not already being used by other devices in the network 3 2 1 Manually Setting Up The Network Parameters In A Browser You need a computer that is using a 10 x x x IP address in order to manually set up the network parameters of the MOBOTIX camera The computer s network parameters usually have to be changed for this purpose 1 Change the network parameters of your computer Windows XP Vista
151. ter clockwise and remove the catch MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com First Installation Steps 6 5 144 3 Remove hinged ferrite and pull out cable Remove the hinged ferrite from the patch cable by cautiously opening the two latches with a small screw driver Gently pull the patch cable out of the housing you may have to remove the foot of the wall mount to be able to do this 4 Attach ferrite at the new patch cable Attach the hinged ferrite at the new patch cable leaving a space of exactly 70 mm 2 8 in between the sealing of the plug and the ferrite gt 70 mm 2 8 in 5 Guide the patch cable into the housing Guide the new cable from the front through the cable guide in the hinge of the VarioFlex mount see figure Reinstall the foot of the wall mount if you removed it in step 3 In order to ensure the weatherproofness of the M15 make sure that you only use genuine MOBOTIX patch cables 6 Connect the patch cable Insert the plug of the Ethernet cable into the appropriate connector Apply bayonet catch as shown and turn it clockwise until it gently snaps shut 7 Make sure that the hinged ferrite rests between the inner housing cover and the cable guide at the top of the housing as shown 8 Close camera housing Close the camera housing as described in Section 2 2 8 MOBOTIX AG Security Vision Systems Made in Germany
152. ultiView screen http camera IP gt control multiview PDA screen http camera IP gt pda PDA event list http camera IP gt control player eventlist amp pda Guest screen http lt camera IP gt cgi bin guestimage html 9 8 44 M15 Camera Manual Operating The Camera 3 2 3 First Images And Network Parameter Configuration In MxControlCenter enter Inude Payer File View Layout VideoSource Recording Took Help MxCentroKC enter Fi 53 Mx 9Q 12 52 38 Fri 25 02 11 Installation Download Download the setup file from the MOBOTIX website to install the latest version The latest MxControlCenter versions are available at www mobotix comin the Support gt Software Downloads gt MxControlCenter section www mobotix com To install MxControlCenter simply double click the setup file and follow the instructions The selected files are copied to the computer older versions will be removed automatically and the shortcuts are created during the installation process Desktop Start Menu etc MxControlCenter will automatically attempt to find all MOBOTIX cameras in the physically connected network that is even a MOBOTIX camera with a factory IP address of 10 x x x Make sure that the firewall settings on your computer are low enough so that MxControlCenter is not blocked If any MOBOTIX cameras are found MxControlCenter can automatically reconfigure them so that they are
153. unc tion The NPA PoE Set connects and remotely supplies a M15 with power via an Ethernet cable up to 100 m in length The blue adapter can also be connected to mobile voltage sources from 12 to 42 V DC by means of an additionally available battery cable The EU ver sion of the NPA PoE Set is supplied as standard with a European adapter while the INT version includes four adapters EU USA UK AUS 1 4 6 MX Patch Box Order no MX OPT PatchT EXT Universal network connector for installation cables MOBOTIX patch cables and standard patch cables IP66 protection class 30 to 60 C 22 F to 140 F The MX Patch Box can be used to connect the patch cable of an IP device with the network installation cable for example Cat 5 or network patch cable RJ45 connector in a weatherproof manner M15 provides an option for directly connecting the installation cable 1 4 7 MX NPA Box Order no MX OPT NPAT EXT The MX NPA Box is a weatherproof PoE injector conforming to the IEEE 802 3af standard and is designed to connect to a MOBOTIX camera external voltage sources 12 to 57 V DC The MX NPA Box is equipped with the Patch Box s weath erproof and extremely compact exterior housing IP66 protection class 30 C to 60 C 22 F to 140 F which means it can also be installed in the space of the Outdoor Wall Mount MX NPA Box interfaces Camera via patch cable Ethernet via LSA and external power supply 12 to 57 V DC is
154. view 91 144 3 1 1 Manually Using A Computer In The 10 x x x IP Address Range You can set up the camera s network parameters using a browser and the embedded camera software To do so connect the camera to a computer or network that is using a 10 x x x IP address range see Section 3 2 1 Manually Setting Up The Network Parameters In A Browser Afterwards you can enter the camera s default IP address in the browser s address bar on your computer see Section 3 2 2 First Images And The Most Important Settings In The Browser Next click on the Admin Menu button to open the camera s Quick Installation in the browser s user interface This is where you can configure the desired network parameters of the cam era Once you have completed the Quick Installation you can connect ihe camera with its new network parameters to the desired network Advantages The camera does not eo M Uve i Mte 10 3 0 99 3 Google P gt need be physically accessible that is it may already be installed No additional software is required The network parameters can be set flexibly through manual entry Disadvantages The computer or the network needs to operate in the 10 x x x IP address range or need to be able to access such a network The setup does not work automatically You need to know the relevant network parameters MOBOTIX AG Security Vision Systems M
155. when using a MX Patch Box All manu MX Patch Box Set x als can be downloaded and printed as PDF files 69 9 DS tu from the MOBOTIX website www mobotix com E a Ag in the Support gt Manuals section Make sure that the cables are not bent or squashed MOBOTIX AG Security Vision Systems Made in Germany www mobotix com sales mobotix com Mounting The Camera With Wall Mount 73 144 5 Mount the camera Place the wall mount over the drill holes and hold it against the wall Then use the four screws each with a washer and tighten them using the appropriate wrench Do not overtighten O O the screws as this may damage the plastic mount Check that the screws are securely in place and place the white caps on the screw heads Then aim the camera as described in Section 3 3 Screw caps for lock screws 6 Clean sensor modules Clean the protective glass and the dome of the sensor modules with a clean soft cotton cloth for optimal image results 7 Establish a connection to the camera check the image Establish a connection to the camera as described in Section 3 1 Manual and Automatic Operation Overview and the following sections The live image from the camera should be visible on the computer monitor Check image sections on the computer monitor The VarioFlex mountand ceiling mountmust always be used for ceiling installation see Section Ceiling Installation
156. x10 8 0 113 Installation Set North Installation Set North This function will perform the following steps Quick Controls Sot the current view as North view The other views East South West will be sot accordingly p Lock all Surround views Browser Reload page 8 Store the complete camera configuration to flash memory Hint if you would like to adjust the Surround view you need to unlock ft first by clicking o B 5 You have now set the North direction for the Surround and Double Panorama display modes In the next step you can set these views as the standard view for the camera live image MOBOTIX 16 5 Anzcige Modus 3 Ausw hlen Admin Menu E Setup Menu Arm amp Record Audio on y MxPEG on 1 Caution No OnScreen Control is available in Double Panorama mode Center Pan Set Default View Load Default View MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com 122 144 M15 Camera Manual Operating The Camera x 4e b d SSL MS DS i uno S neo In the Display Mode Quick Control select the option Surround or Double Panorama You can fine tune the views using the vPTZ via mouse or joystick and as described above by unlocking and locking the standard view using the lock icon open lock correct display and close lock again For each of the subviews North East etc see below the OnScreen Control on the
157. xEasy will provide a dialog box for this purpose When using the MicroSD card from one MOBOTIX camera in another MOBOTIX camera you need to make sure that the time on the original camera is in sync with the new camera We recommend using automatic time synchronization via a time server Admin Menu Date and Time 3 5 5 Deactivating Card Recording Follow these steps to deactivate recording to a MicroSD card Admin Menu Storage on External File Server Flash Device l Activate the None option 2 Click on the Set button at the bottom of the dialog box and then Close 3 Reboot the MOBOTIX camera Admin Menu gt Reboot Camera Once the camera has rebooted make sure that the symbol FR REC is no longer visible in the bottom right hand corner of the live image 4 You can now safely remove the MicroSD card from the camera see Section 2 6 Replacing The MicroSD Card MOBOTIX AG e Security Vision Systems Made in Germany www mobotix com sales mobotix com MicroSD Card Recording 129 144 A MicroSD card may only be removed from the camera after you have deacti vated the recording to MicroSD card and rebooted the camera Failing to do so may lead to data loss Removing connected flash storage devices from the camera without properly deac tivating them may lead to data loss and or destroy certain sectors of the storage device This is limited to 4 MB of lost data per incident due to MxFFS formatt

Mobotix M15D-SEC - Network Webcams

Contents

Download Pdf Manuals

Related Search

Related Contents