Installing 46-55" flat panel screens on the ML10/MP10 wall
Contents
1. minimum clearance to allow the bracket to be easily released 10 Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 020 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount 9 Turn the knobs located on the bottom of the mount to adjust the position until it is vertically centered Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 11 020 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount Vertical ___ gt mount 10 Check that the mount is level If necessary fine adjust the vertical position 11 Adjust the vertical position of the panel to leave a minimum 1 mm 0 04 gap between panels so the weight of the panels do not rest on the panels underneath Always adjust the X position of the panels individually rather than pushing an entire row left to right For example if you are constructing a 3x3 video wall push the panels individually from the right and left sides towards the center of the wall Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 12 020 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount A Leave a small gap between panels Attaching the adapter brackets to the display The panel must have the adapter brackets installed before it can be attached to the wall bracket Attach the2. e Adjustable VESA mounting hole patterns in 100 mm 3 9 increments starting at 200 x 200 mm 7 9 x 7 9 up to 600 x 400 mm 23 6 x 15 7 for MP10 LCD mounts Additional patterns supported with adapter plates Safety warnings and cautions To prevent personal injury and to protect the device from damage read and follow these safety precautions e The supporting structure must safely support the combined load of the product all attached hardware and components following all local safety standards and regulations l Warning Failure to comply with the following could result in death or serious injury e A minimum of two people or lift equipment is required to safely lift install or move the product e Always handle the screen from its sides Do not touch the inside of the screen e Christie products must be installed and serviced by Christie qualified technicians Caution Failure to comply with the following could result in minor or moderate injury e Do not over tighten hardware e This product is intended for indoor use only Types of installations Learn the supported surfaces for installing the wall mounts Wall construction Hardware required Wood Stud Included Wood Beam Included Solid Concrete Not Included Cinder Block Not Included Unistrut P series Not Included Metal Stud Contact Qualified Professional Brick Contact Qualified Professional Other Contact Qualified Professional Installing Flat
3. 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount yo 5 To identify where the mount for the second row of displays should be installed measure the height of the display panel from the top of the bottom left display to the top of the first display in the second row Y Installing the mount to wall studs plywood drywall over wall studs Learn how to install the wall mounts onto wall studs plywood or drywall Hardware provided is for attaching the mount through standard thickness drywall or plaster into wood studs Installers are responsible for providing the hardware for other types of mounting situations When installing the wall mounts on a wood stud wall covered with plywood verify that the wood studs are a minimum of 2 x 4 nominal size and plywood is a minimum 1 2 13 mm thickness Plywood may be covered by drywall up to 5 8 thick 1 Use an edge to edge stud finder to locate the edges of the stud 2 Based on their edges draw a vertical line down the stud center 3 Place the pull out mount assembly on the wall to use as a template and verify the pull out mount is level on the center line of the stud 4 Mark the center of the four mounting holes Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 6 020 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount In the landscape orientation ma
4. CHRISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount The ML10 MP10 is a full service video wall mount that can accommodate the FHD462 X and FHD552 X LCD flat panels The ML10 mount is used for landscape orientations and the MP10 mount is used for portrait orientations The modular mount system features an innovative pull out and prop open hinge mechanism that provides rear screen access the ability to adjust the X Y and Z axis alignment and wall plate spacers that set each mount into position MP10 Portrait Features Use the ML10 and MP10 wall mounts to hang and adjust the flat panels and to access the rear of the panels e Modular mount for large video wall display configurations e Tool less adjustments of panels for optimal gaps e Spring loaded mechanisms secure displays Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 1 020 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount e Pull out prop open mechanism provides quick service access e Integrated cable management tie backs make display to display cabling simple e Included security hardware prevents the mount from extending out from the wall e Adjustable VESA mounting hole patterns in 100 mm 3 9 increments starting at 200 x 200 mm 7 9 x 7 9 up to 700 x 400 mm 27 5 x 15 7 for ML10 LCD mounts Additional patterns supported with adapter plates
5. Panels on the ML10 MP10 Wall Mount Instruction Sheet 2 020 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount Required kits Learn the kits that are required for installing the wall mounts e LCD Mount 40 65 ML10 Landscape P N 135 101103 xx e LCD Mount 40 65 MP10 Portrait P N 135 104106 xx Optional kits e LCD Spacer Kit 55 ML10 135 102104 xx e LCD Spacer Kit 55 MP10 135 107109 xx Other available resources e LCD Panel FHD552 X User Manual P N 020 000741 xx e LCD Panel FHD462 X User Manual P N 020 000769 xx e ML10 MP10 Spacer kit for the FHD552 X Instruction Sheet P N 020 100728 xx Required parts Learn the parts necessary for installing the wall mounts ML10 7 i TRO j 4 O 6 Oo f fr 0 A Pull out mount assembly Qty 1 H M6 x 12 mm socket pin screw Qty 4 Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 3 020 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount Oo 1m mM OY DW Adapter Bracket Qty 2 I M8 x 16 mm socket pin screw Qty 4 14 x 2 5 hex head wood screw Qty 5 J 4mm Allen wrench Qty 1 Fender washer Qty 4 Mesh sleeve not shown Qty 1 Nylon shoulder washer Qty 4 Cable tie not shown Qty 2 M5 x 10 mm socket pin type F screw Qty 2 Required tools Ensur
6. adapter brackets to the back of the panel using four M6 x 12 mm socket pin screws with a nylon shoulder washer or four M8 x 15 mm socket pin screws as shown below Landscape orientation Washer Socket pin screw MAX VESA 700 mm MIN VESA 200 mm 5 Adapter brackets 400mm 300mm 200mm o PLP Portrait orientation Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 13 020 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount MAX VESA 400 mm MIN VESA 200 mm Socket Adapter brackets a pin screw eee 600 mm ed Eart tld GUN fem om gt ete Attaching the panel to the wall mount Install the panel with the brackets onto the wall mount 1 Slide the adapter brackets into position 2 Loosely fasten the panel in place using the security screw Landscape orientation Portrait orientation Adapter bracket Adapter bracket 3 Adjust the panel until it is 2 50 8 mm from the center 4 To lock the panel in place use a 4mm Allen wrench to tighten the security screws Adjusting the pull out mount asse
7. all mount Adapter bracket dapter bracket tt es TE Closing the adapter brackets Take caution when closing the adapter brackets to ensure the LCD panel is not damaged 1 Pull down on the short front release cords Once the short cords are pulled the kick stand will disengage You may need to slightly pull the display away from the wall to release the kick stand Landscape orientation Adapter bracket f dapter bracket Portrait orientation Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 18 020 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount 2 Gently guide it back into place as you close the brackets Securing the pull out mount assembly Optional Prevent the locking tabs from releasing Insert and tighten two M5 x 10 mm socket pin type F screws into the locking tab Landscape orientation Portrait orientation Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 19 020 101712 03 Rev 1 07 2015
8. e the appropriate tools are available during the installation Stud finder edge to edge stud finder is recommended Phillips screwdriver Socket wrench Pencil Drill 3 8 socket 5 16 8 mm bit for concrete and cinder block walls 5 32 4 mm bit for wood stud walls Level Installing the wall mount Learn how to install the wall mounts onto different surfaces The maximum load capacity of the wall mount is 125 Ibs 57 kg Illustrations are graphical representations only and are provided to enhance the understanding of the written material When installing the wall mounts ensure there is proper spacing between the mounts to accommodate the panels Always start with the bottom left display in the array Measure the width and height of the display panel Locate the center of the bottom left display am 21 fmm 20 2 36min1 8 92 227mm Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 020 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount 3 To identify where the mount for the display to the right of the first display should be installed measure the width of the display panel from the center of the first display to the center of the second display X 4 Install all panels in the bottom row Install all rows starting with the far left display Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 5 020
9. he center of the four mounting holes In the landscape orientation make sure there is a minimum 16 406 4 mm horizontal distance between the 14 x2 5 screws Landscape orientation Portrait orientation Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 020 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount Solid concrete Fender washers Fender washers 14 x 2 5 screws 14 x 2 5 screws Pull out mount assembly Pull out mount assembly Use a standard electric drill on slow setting to drill four 5 16 8 mm diameter holes to a minimum depth of 2 5 64 mm To avoid breaking out the back of the hole when entering a void or cavity do not use a hammer drill On cinder block walls mount in a solid part of the block generally 1 25 mm minimum from the side of the block Do not drill into mortar joints Insert anchors into the holes flush with the wall Never attach concrete expansion anchors to concrete covered with plaster drywall or other finishing material If mounting to concrete surfaces covered with a finishing surface is unavoidable the finishing surface must be counter bored as shown in the image below concrete a ee ke atin ee we T O AE I Y wl y Lea IE tess j dnine EE CU ign es MO D Pa w EA plaster bzy drywall CUTAWAY VIEW Place the pull out mount assembly over the anch
10. ke sure there is a minimum 16 406 4 mm horizontal distance between the 14 x 2 5 screws Landscape orientation Portrait orientation Wood stud Wood stud TEL in Pull out mount assembly Fender washer Pull out mount assembly ty Fender washer Wood screw Wood screw Drill four 5 32 4 mm diameter holes 2 1 2 65 mm deep Tighten the four 14 x 2 5 wood screws and fender washers so that the wall plate is firmly attached but do not over tighten Never tighten in excess of 80 in lbs 9Nm Installing the mount to solid concrete or cinder block Learn how to install the wall mounts onto solid concrete or cinder block walls Concrete must be a minimum of 2000 psi density Lighter density concrete may not hold the Warning Failure to comply with the following could result in death or serious injury concrete anchor The supporting structure must safely support the combined load of the product all attached hardware and components following all local safety standards and regulations When installing wall mounts onto cinder blocks verify that you have a minimum of 1 3 8 35 mm of actual concrete thickness in the hole to be used for the concrete anchors Cinder block must meet ASTM C 90 specifications and a minimum nominal width of 8 1 Place the pull out mount assembly on the wall to use as a template and verify the pull out mount is level 2 Mark t
11. le the cables with the mesh sleeve and cable ties Opening and closing the pull out mount assembly Unlock the mount to pull the panel out from the wall 1 Release the locking tab to open the pull out mount assembly 2 Push or pull up on the locking tab Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 020 101712 03 Rev 1 07 2015 16 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount To avoid damaging the LCD panel always release both locking tabs at the same time and move the panel forwards evenly Landscape orientation 3 SQI Ji ey 1 Opening the adapter brackets Portrait orientation PULL UP PUSH UP Lift the bottom of the panel up and away from the pull out mount To open the adapter brackets pull down on the long back release cords while pulling the bottom of the display away from the wall Two people are required when opening the adapter brackets one to release the left side release cord and the other the right side release cord After the back release cords are pulled the kick stand engages to hold the panel open Landscape orientation dapter bracket Portrait orientation Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 020 101712 03 Rev 1 07 2015 Adapter bracket 17 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 w
12. mbly Align the pull out mount Use the knob to make fine tuned adjustments to the pull out mount alignment e Turn the knob clockwise to raise a side e Turn the knob counter clockwise to lower a side Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 14 020 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount Portrait Landscape Adjusting the adapter bracket Align the panel adapter brackets Use the knob to make fine tuned adjustments to the panel alignment e Turn the knob clockwise to raise a side e Turn the knob counter clockwise to lower a side Adapter Bracket Adjustment Landscape Adapter Bracket Adjustment Portrait n OOo Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 15 020 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount Securing the display cables Display cables can be routed through the top or bottom of the pull out mount assembly 1 Use the cable ties and cable management slots on the pull out mount assembly to secure the display cables Landscape orientation Detail 3 Detail 3 2 Bund
13. ors and secure it with four 14 x 2 5 screws and fender washers Make sure concrete anchors do not pull away from the concrete when tightening screws If the wall is covered with plaster drywall or other finishing material thicker than 5 8 16 mm custom fasteners must be supplied by the installer Tighten the four 14 x 2 5 wood screws and fender washers so that the wall plate is firmly attached but do not over tighten Never tighten in excess of 80 in lbs 9Nm Installing the mount to a Unistrut P series metal frame Learn how to install a wall mount onto the Unistrut metal frame channel When installing Peerless wall mounts to Unistrut P Series metal framing channels the channels must be installed and supported per the Unistrut design specifications Use only compatible Unistrut hardware Never exceed maximum load capacity of Unistrut channel or supporting surface 1 2 Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet Insert the 1 4 20 Unistrut channel nut with spring on the Unistrut metal frame channel Level and install the Unistrut P series metal frame channel to the wall according to the instructions included with the Unistrut frame Attach the wall mount to the Unistrut metal frame channel with the 1 4 20 hex head screws 020 101712 03 Rev 1 07 2015 CHAISTIE Installing 46 55 flat panel screens on the ML10 MP10 wall mount Installing the mount to the F100 frame Learn how to install
14. the wall mounts onto the F100 frame 1 Make sure all components within the video wall are level starting with the P100 Pedestal If the floor surface is not level adjust the feet on the pedestal For information on installing the P100 pedestal and the F100 frame see P100 Pedestal and F100 Frame for FHD552 X Installation Manual 020 101714 xx 2 Install the F100 Frame onto the pedestal If the F100 Frame is used as stand alone unit it must be leveled before securing the wall mount 3 Before installing the wall mount use a standard level to check alignment on the horizontal and vertical edge of the frame 4 Position the wall mount within the center of the frame aligning it with the mounting holes 5 Tighten the wall mount to the F100 Frame using the four M6 screws Never tighten in excess of 80 in Ibs 9Nm Installing Flat Panels on the ML10 MP10 Wall Mount Instruction Sheet 9 020 101712 03 Rev 1 07 2015 Installing 46 55 flat panel screens on the ML10 MP10 wall mount CHRISTIE Front View _ lt F100 frame r T i P LS Wall mount Q Y a M6 screw 1 of 4 Back View 6 For good screen planarity within a video wall adjust the top knob of the adapter bracket to achieve a 9 mm 0 35 gap gt gt lt S N gt gt S 7 Adjust the bottom knob of the adapter bracket to achieve a 14 mm 0 55 gap If further adjustment is required leave a 1 mm 0 04
Download Pdf Manuals
Related Search