Preview Sewing Information for #21013
Contents
1. Appliqu Fuse amp Fix Stabilizer Embroidery Thread Stabilizer that is approptiate for your project BERNINA CutWork Accessory PREPARE APPLIQUE FABRIC Starch appliqu fabric 2 3 times following manufacturer s instructions Appliqu fabric should be crisp Iron Appliqu Fuse amp Fix to the wrong side of the starched appliqu fabric following instructions on product packaging CUT APPLIQUE PIECES Hoop one layer of Cut Away Stabilizer Send first CWA file to the embroidery machine CWA files are the pre cut appliqu files to use with the CutWork Accessory these files will end in CWAOT CWA02 and CWA03 etc The number of CWA files available for each design will depend upon how many separate appliqu s each design contains Stitch the first color this will be the placement stitch Remove the hoop from the machine but do not remove the stabilizer from the hoop Spray the hooped stabilizer with temporary spray adhesive Lay prepared appliqu fabric over the placement stitch being sure to completely cover the stitching Apply pressure to appliqu fabric to ensure it is adhered Stitch the second color this will be the basting stitch It is meant to baste the appliqu fabric to your hooped stabilizer Replace normal stitch plate with the CutWork stitch plate Unthread the machine If necessary turn off the upper thread control on your machine Refer to your machine s user manual Note that the most recent version of2. Em 4 Dark Blue Detail ee ceecesseeseereeees 4032 mn 5 Medium Green Detail 0352 mu 6 Dark Green Detail 5934 T Pink Detail iii 2051 21013 17 Leaf Vine 1 Em 1 Light Green Detail 6051 2 Pink Detail 2051 3 Light Blue DEE ups 4152 4 Medium Blue Detail 4332 5 Pale Blue Detail rsvrrnvrrrvrnrvrnrvrenvrrsvrrrvrrrversvrenne 4250 6 Medium Green Detail 0352 Mm 7 Dark Green Detail 5934 21013 18 Leaf Vine 2 1 Light Green D lires 6051 2 Light Blue Detail 4152 mu 3 Medium Blue Detail 4332 4 Pink Detail ii 2051 m 5 Medium Green Detail 0352 Mm 6 Dark Green Detail 5934 21013 19 Leaf Vine 3 1 Light Green Detail 6051 2 Medium Green Detail 0352 3 Light Blue DEG uer 4152 Mm 4 Dark Green Detail 5934 mu 5 Medium Blue Detail ceeesereeeeeeeees 4332 6 Pink D tail 2051 21013 20 Leaf Vine 4 1 Pale Blue Detail 4250 2 Light Blue D RIL ss 4152 3 Pink Detail 2051 mm 4 Medium Blue Detail 4332 mn 5 Medium Green Detail 0352 mu 6 Dark Green Detail 5934 21013 21 Feather Leaf 1 1 Pink Detail inner 2051 Em 2 Light Green Detail 6051 3 Light Blue Dei Le ge 4152 mn 4 Medium Green Detail eee eeeeeeeeees 0352 Mm 5 Dark Green Detail 5934 Se Feather Leaf 2 Light Green Detail 6051 i Pink Detail 2051 3 Light Blue Des 4152 m 4 Medium Green Detail ceesen seers 0352 Mm 5 Dark Green Detail 5934 21013 23 Appliqu
3. Printer Name Savin C3535 PCL5c v la Properties Status Ready Comments and Forms Type Savin C3535 PCL5c Document and Markups x Print Range Preview Composite All k 3 5 Current view r Current page Pages 1 51 Subset All pages in range Reverse pages Page Handling Copies 1 Page Scaling None Auto Rotate and Center Choose paper source by PDF page size Print to file Document 8 5 x 11 0n ER Paper 8 5 x 11 0in Print color as black 1 52 Printing Tes Summarize Comments TO SAVE PAPER Only print the desired image by navigating to the image s page go to File gt Print and select Current page in the print dialog box Repeat for each desired image Print Range All J Current view Current page Pages 1 51 Subset All pages in range Reverse pages It is a violation of Copyright law to make and distribute copies of electronic designs or artwork Electronic designs are licensed to the original purchaser for use at one location 2014 Benartex Studios All rights reserved Of SD A New Leaf Appliqu Patterns 21013 05 Small Leaf 21012 02 Small Leaf 21013 01 Leaf 21013 08 Leaf 21013 10 Small Leaf 21013 06 Leaf 21013 11 Leaf It is a violation of Copyright law to make and distribute copies of electronic designs or artwork Electronic designs are licensed to the original purchaser for use at one location 2014 Benartex
4. Be a NOTE The patterns are sized for the designs as they were made If you resize the design you will need to resize the pattern the Same amount You can print out the pattern at the normal size then copy it on a copy machine at the changed size For example resize the designs to 80 resize the printed pattern to 80 TIP When Printing the patterns make sure that the Fit to page option is UNCHECKED in the Print Dialog Box If this option is checked the printed patterns will not be actual size PRINTABLE This printable design can be printed on printable fabric or heat transfer paper This JPG design on the CD is ready for printing just follow the manufacturet s instructions for printing and applying WMF design format can be imported into BERNINA Embroidery Software 6 with CorelDRAW to design mixed media applications Reference the CorelDRAW manual for tips on creating mixed media applications It is a violation of Copyright law to make and distribute copies of electronic designs or artwork Electronic designs are licensed to the original purchaser for use at one location 2014 Benartex Studios All rights reserved Of SD A New Leaf Appliqu Patterns ATTENTION When printing this document any page scaling or page fitting options in your print dialog box must be turned OFF or set to NONE so that your files will print out at their actual size Images not printed at actual size will not function as intended Print
5. Blue Detail 4152 Em 6 Medium Blue Detail 4332 Em 7 Dark Blue Detail ceecesseeseeeeeneen 4032 mn 8 Dark Green Detail 5934 21013 05 Leaf Branch 5 Appliqu mm 1 Light Green Detail 6051 2 Pale Blue Detail sise 4250 B Pink D s de ann 2051 4 Light Blue Detail 4152 Mm 5 Medium Blue Detail eee eeeeeeeeneee 4332 Mm 6 Dark Blue Detail 4032 7 Small Leaf Placement Stitch 0015 EH 8 Tackdown 5610 mn 9 Medium Green Detail 0352 mm 10 Dark Green Detail 5934 21013 06 Leaf Branch 6 Appliqu 1 Pale Blue Detail rsorrrvvrrvrrrnrrevvrrvrervrrrrrrnrernrenn 4250 2 Leaf Placement Stitch 0015 EM 3 Tackdown re 5610 Mm 4 Light Green Detail 6051 Em 5 Medium Blue Detail 4332 mu 6 Dark Green Detail 5934 mn 7 Medium Green Detail 0352 0 Pink D S ee es 2051 Em 9 Dark Blue Detail 4032 21013 07 Leaf Branch 7 Mm 1 Light Green Detail 6051 Em 2 Dark Blue Detail eee ceeeerseeeeenees 4032 gt Pink DEA sandebtactechestdzanbtecsniaes 2051 Em 4 Medium Blue Detail 4332 5 Pale Blue Detail rsrrvrrrrrrvrrrvorsvrrnvrrsverrverrsrennn 4250 mn 6 Medium Green Detail 0352 Mm 7 Dark Green Detail 5934 21013 08 Leaf Branch 8 Appliqu 1 Leaf Placement Stitch 0015 De TackdoWwn anne and tee tee 5610 3 Pale Blue Detail srrrvrrrvrrrrrrvrrsvrrnvvrrverrverrsrennn 4250 m 4 Light Green Detail 6051 Mm 5 Dark Blue Detail 4
6. Medallion 1 Circle Placement Stitch eeeseeeeeeeeees 0015 EM 2 Tackdown 5610 3 Light Blue Details nu 4152 4 Pink Detail iii 2051 mn 5 Medium Green Detail ceeeeeeeeneeeees 0352 mu 6 Dark Green Detail 5934 mu 7 Medium Blue Detail ceeeereeeeeeeeees 4332 Em 8 Dark Blue Detail eeeceesersseneeees 4032 21013 24 Medallion mm 1 Light Green Detail 6051 mn 2 Medium Green Detail 0352 3 Pale Blue D tails 4250 Em 4 Medium Blue Detail 4332 5 Light Blue D tails 4152 Mm 6 Dark Green Detail 5934 7 Pink Detail 2051 21013 25 Linework Medallion 1 0 ns D cera eeu deaiseuets 2051 m 2 Light Green Detail 0352 3 Light Blue Detail 4152 21013 26 Linework Leaf 1 mn 1 Medium Green Detail 0352 Mm 2 Medium Blue Detail 4332 21013 27 Linework Leaf 2 mn 1 Medium Green Detail 0352 mm 2 Medium Blue Detail 4332 21013 28 Linework Leaf 3 m 1 Medium Green Detail 0352 mm 2 Medium Blue Detail 4332 21013 29 Swirls Border mm 1 Single Color Design 4332 21013 30 Swirls Corner mm 1 Single Color Design 4332 It is a violation of Copyright law to make and distribute copies of electronic designs or artwork Electronic designs are licensed to the original purchaser for use at one location 2014 Benartex Studios All rights reserved Of SD A New Leaf by Benartex Studios 21013 30 Designs Note Use Design Works Software to edit CutWork PaintWork and Crysta
7. See Photo 4 10 Place hoop on machine and use your machine s check feature to ensure that the template material is positioned correctly Punch the first color change Note The machine will prompt you when the container is full and needs to be emptied However you may also wish to empty the container between color changes ANY time ee see 18 bu 9959099 you remove the container for cleaning be sure to repeat Step 7 to ensure that the container is positioned properly Check the back of the parchment paper between color changes also to remove any stray dots that may be stuck to the paper 11 If more than one size crystal is used in the design replace the punch tool and the punch plate on the top of the PHOTO 7 container with sizes to correspond with the size shown on the Color Bar of the machine Repeat this process as needed until the design is finished See Photo 5 12 Carefully peel the rhinestone template material away from the parchment paper and place on a piece of rhinestone template backboard Smooth into place 13 Pour the largest size of crystals used in the design over the template and use a small rhinestone brush to push them into place See Photos 6 and 7 14 Make sure that all holes of that size are filled and that all crystals are facing upright PHOTO 9 15 Repeat Steps 13 and 14 for any additional sizes continuing id s KOM KOMEN with the next largest size and progressing to the smal
8. licensed to the original purchaser for use at one location 2014 Benartex Studios All rights reserved OLSD 21013 01 Leaf Branch 1 Appliqu 1 Leaf Placement Stitch 0015 EE 2 TackdoWwn 5610 m 3 Light Green Detail 6051 4 Pale Blue Detail rssorrvrrrvrrrvrrevrrvvrrvrerrervreneenn 4250 5 Light Blue Detail 4152 mu 6 Medium Blue Detail 4332 Mm 7 Dark Green Detail cesecessseseeteenees 5934 Em 8 Dark Blue Detail ceeceesseeeeeeeneen 4032 9 Pink Detail ir 2051 mn 10 Medium Green Detail 0352 21013 02 Leaf Branch 2 Appliqu 1 Small Leaf Placement Stitch 0015 EM 2 TackdoWwn 5610 Em 3 Light Green Detail 6051 mn 4 Medium Green Detail 0352 5 Light Blue DEE maser 4152 6 Pink Detail ceccesessesscerscsseeesereeseenneereens 2051 7 Dark Green Detail 5934 8 Medium Blue Detail 4332 9 Dark Blue Detail 4032 10 00 na mme 2051 11 Light Blue SOS deummiennensne 4152 21013 03 Leaf Branch 3 1 Light Green Detail 6051 2 Pale Blue Dels usmnnunmnnnngumd 4250 3 Light Blue Detail 4152 Em 4 Medium Blue Detail 4332 Mm 5 Dark Blue Detail ice ceseeeeeeeeneen 4032 mn 6 Medium Green Detail 0352 Mm 7 Dark Green Detail 5934 8 Pink Detail 2051 21013 04 Leaf Branch 4 Mm 1 Light Green Detail 6051 2 Pink Detail ii 2051 3 Pale Blue Detail srrrvrrrvrrsvrrrvorsvrrnvrrrverrverrsrennn 4250 mn 4 Medium Green Detail 0352 5 Light
9. 032 mn 6 Medium Green Detail 0352 Mm 7 Dark Green Detail 5934 Mm 8 Medium Blue Detail 4332 9 Pink Def Lusis 2051 A New Leaf by Benartex Studios 421013 30 Designs Listings below indicate color sample stitching order and suggested thread color number Most colors indicate Isacord threads However colors beginning with 20501 refer to YLI Fine Metallics 7 refer to Yenmet Metallic 8 refer to YLI Variations Variegated Thread and 9 refer to Isacord Multicolor Variegated 21013 09 Leaf Branch 9 1 Light Green DEG less 6051 2 Pink Detail 2051 3 Light Blue DER ctentoumiteatne 4152 Em 4 Medium Blue Detail 4332 mn 5 Medium Green Detail 0352 Mm 6 Dark Green Detail 5934 mm 7 Dark Blue Detail 4032 21013 10 Large Oval Leaf Branch Appli iqu ight Green Detail 6051 Pale Blue Detail rssrrvrrrvrnrvrnrvrennresvvervrrsversvrenne 4250 3 Light Blue Dei 4152 Em 4 Medium Blue Detail 4332 Mm 5 Dark Blue Detail cceceeseeeeeneeenees 4032 6 Pink Detail ir 2051 mn 7 Medium Green Detail 0352 8 Small Leaf Placement Stitch 0015 Em 9 Tackdown 5610 mm 10 Dark Green Detail 5934 21013 11 Jumbo Leaf Branch Appigue 1 Light Green Detail eeesesseeseeeeeeeerees 2 Pale Blue Detail ssoorvvrrrvrrrvrrnvrrrvrrrvrrrvrervrerveenn pek 3 Light Blue Dei 4152 Em 4 Medium Blue Detail 4332 EE 5 Dark Blue Detail u mms 4032 6 Pink DSG ne 2051 7 Medium G
10. CutWork Appliqu Accessory Cut 3 Cut 3 mm 5 Bernina CutWork Appliqu Accessory Cut 4 Cut 4 mm 5 Bernina CutWork Appliqu Accessory Cut 4 Cut 4 21013 06 CWA For Use with the 21013 12 CWA For Use with the Bernina CutWork Accessory Bernina CutWork Accessory EE 1 Basting SUC sears sonst scrasdntwnedsndsatsttendsbeliiaasanewantens 3600 EE 1 Basting SUG kesemsesssnnsunejsnnden i n 3600 mm 2 Bernina CutWork Appliqu Accessory Cut 1 Cut 1 mm 2 Bernina CutWork Appliqu Accessory Cut 1 Cut 1 mm 3 Bernina CutWork Appliqu Accessory Cut 2 Cut 2 mm 3 Bernina CutWork Appliqu Accessory Cut 2 Cut 2 mm 4 Bernina CutWork Appliqu Accessory Cut 3 Cut 3 mm 4 Bernina CutWork Appliqu Accessory Cut 3 Cut 3 mm 5 Bernina CutWork Appliqu Accessory Cut 4 Cut 4 mm 5 Bernina CutWork Appliqu Accessory Cut 4 Cut 4 It is a violation of Copyright law to make and distribute copies of electronic designs or artwork Electronic designs are licensed to the original purchaser for use at one location 2014 Benartex Studios All rights reserved Making Precut Appliqu Using O SD BERNINA CutWork Accessory er 13 14 15 oe aa NN 9 10 11 12 Attach the hoop to the machine To cut the first appliqu piece follow the thread changes on your machine screen and SUPPLIES Cut Away Stabilizer PHOTO I Temporary Spray Adhesive
11. Of SD A New Leaf by Benartex Studios 21013 30 Designs Note Some designs in this collection may have been created using unique special stitches and or techniques To preserve design integrity when rescaling or rotating designs in your software always rescale or rotate designs using the handles directly on screen A 21013 01 Leaf Branch 1 21013 02 Leaf Branch 2 21013 03 Leaf Branch 3 21013 04 Leaf Branch 4 Appliqu Appliqu 4 76 X 6 47 in 4 50 X 5 08 in ess _ de er 7 es ia 120 90 X 164 34 mm 114 30 X 129 03 mm 123 95 X 145 80 mm 123 44 X 160 27 mm 11 685 St d L 16 429 St BU L 20 607 St BL L 19 793 St BU L 21013 05 Leaf Branch 5 21013 06 Leaf Branch 6 21013 07 Leaf Branch 7 21013 08 Leaf Branch 8 Appliqu Appliqu 3 51 X 4 88 in Appliqu 4 74 X 5 17 in 4 44 X 4 82 in 89 15 X 123 95 mm 4 59 X 4 67 in 120 40 X 131 32 mm 112 78 X 122 43 mm 10 493 St amp 4 116 50 X 1180 m 15 522 St W L 16 750 St 38 9 854 St 387 21013 09 Leaf Branch 9 21013 10 Large Oval Leaf 21013 11 Jumbo Leaf Branch 21013 12 Leaf 1 Appliqu 3 72 X 4 09 in Branch Appliqu Appliqu 3 34 X 3 83 in 94 49 X 103 89 mm 5 44 X 8 95 in 977 x 1097 in 84 84 X 97 28 mm 7 332 St 0 138 18 X 227 33 mm 222 76 X 278 64 mm 8 899 St 3 25 293 St 85 L 50 417 St 8 L Design contains a loose fill L Design is larger than 5 127 mm in either direction 13 Some white areas shown are not stitched S Design is smaller than 1 5 38 1 mm i
12. Studios All rights reserved Of SD A New Leaf Appliqu Patterns 21013 23 Medallion Center 21013 14 Leaf It is a violation of Copyright law to make and distribute copies of electronic designs or artwork Electronic designs are licensed to the original purchaser for use at one location 2014 Benartex Studios All rights reserved OLSD A New Leaf Pre cut appliqu files for use with BERNINA CutWork Accessory 21013 01_CWA For Use with the Bernina CutWork Accessory 2 37 X 2 55 in 60 20 X 64 77 mm 1 000 St 21013 02_CWA For Use with the Bernina CutWork Accessory 1 63 X 1 31 in 41 40 X 33 27 mm 500 St S 21013 05_CWA For Use with the Bernina CutWork Accessory 1 56 X 1 39 in 39 62 X 35 31 mm 600 St S 21013 08 CWA For Use with the Bernina CutWork Accessory 2 15 X 1 17 in 54 61 X 29 72 mm 600 St S 21013 14 CWA For Use with the Bernina CutWork Accessory 1 82 X 2 63 in 46 23 X 66 80 mm 800 St 21013 10 CWA For Use with the Bernina CutWork Accessory 1 76 X 1 68 in 44 70 X 42 67 mm 700 St Jo Ff P 21013 23_CWA For Use with the Bernina CutWork Accessory 3 35 X 3 35 in 85 09 X 85 09 mm 1 300 St 21013 11_CWA For Use with the Bernina CutWork Accessory 1 67 X 1 88 in 42 42 X 47 75 mm 700 St VA T 21013 06 CWA For Use with the Bernina CutWork Accessory 2 19 X 2 84 in 55 63 X 72 14 mm 1 000 St 21013 12 CWA For Use with the Bern
13. an 5 127 mm in either direction 14 Some white areas shown are not stitched S Design is smaller than 1 5 38 1 mm in either direction It is a violation of Copyright law to make and distribute copies of electronic designs or artwork Electronic designs are licensed to the original purchaser for use at one location 2014 Benartex Studios All rights reserved Of SD A New Leaf by Benartex Studios 21013 30 Designs Note Some designs in this collection may have been created using unique special stitches and or techniques To preserve design integrity when rescaling or rotating designs in your software always rescale or rotate designs using the handles directly on screen 21013 25 Linework Medallion 21013 26 Linework Leaf 1 21013 27 Linework Leaf 2 21013 28 Linework Leaf 3 4 75 X 4 75 in 4 07 X 4 60 in 3 46 X 3 97 in 3 40 X 3 93 in 120 65 X 120 65 mm 103 38 X 116 84 mm 87 88 X 100 84 mm 86 36 X 99 82 mm 7 048 St lt 3 4 048 St 2 981 St amp 2 493 St lt 3 j 4 af 21013 29 Swirls Border 21013 30 Swirls Corner 5 98 X 1 58 in 2 98 X 2 99 in 151 89 X 40 13 mm 75 69 X 75 95 mm 7 581 St 38 L 5 525 St 38 Design contains a loose fill L Design is larger than 5 127 mm in either direction 13 Some white areas shown are not stitched S Design is smaller than 1 5 38 1 mm in either direction It is a violation of Copyright law to make and distribute copies of electronic designs or artwork Electronic designs are
14. ease the clamping lever and insert the appropriate pen with a slight twisting motion until the tip just touches the pen guard Close the clamping lever The pen should now be held firmly in place NOTE Although there should be some pressure against the pen as it is inserted do not use excessive force without supporting the PaintWork tool 9 Swing the pen guard up and start painting using the Start Stop button on the machine NOTE It is advisable to hoop a test piece of fabric to test for pen pressure prior to the painting on the actual project An alternative to this is to cut a hoop sized piece of Stabil Stick remove the paper from the entire back and place the Stabil Stick over the hooped project Start the machine and paint for a few seconds Adjust the pen pressure as needed to achieve the look you desire See Photo 1 Turning the dial counter clockwise decreases the pressure Turning the dial clockwise increases the pressure When you have achieved the desired effect remove the Stabil Stick from the top and re start the design from the beginning 10 When the first color is finished swing the pen guard down Open the clamping lever and remove the pen 11 Clean the pen guard between color changes and allow fabric to dry between color changes to avoid mixing colors Tip To help guarantee colors will not mix remove the hoop from the machine but not the fabric from the hoop Use a small Appliqu iron to heat the color Replace the hoop and con
15. er area and repeat NOTE Time and temperature given here are meant as guidelines only Refer to instructions from the crystal manufacturer for best results 23 Allow the transfer to cool completely before peeling the transfer tape away See Photo 12 PAINTWORK INSTRUCTIONS 1 Remove the upper thread and needle from the machine 2 Attach the Straight Stitch CutWork Stitch Plate to the machine 3 Open the clamping lever on the PaintWork tool and slide the appropriate pen adaptor into the shaft of the tool Close the clamping levet 4 Attach the PaintWork tool over the presser foot holder cone and secure with the levet 5 Prior to hooping iron the fabric to remove any wrinkles The fabric must be smooth and hooped securely in order to ensure proper working of the tool 6 Hoop your project using the appropriate stabilizing method Method A a Hoop piece of Stabil Stick Cut Away or Stabil Stick Tear Away by itself in the hoop b Score and remove the papet c Place the fabric to be painted over the sticky surface with right side up Gently smooth into position For best results the stabilizer should be adhered to as much area of the fabric as possible Method B PHOTO 2 a Spray stabilizer of your choice with a generous amount of temporary spray is adhesive b Place the sprayed side of the stabilizer on the wrong side of the fabric Hoop all layers as one unit 7 Attach the hoop to the machine 8 Swing the pen guard down Rel
16. ina CutWork Accessory 3 35 X 3 85 in 85 09 X 97 79 mm 1 400 St Itis a violation of Copyright law to make and distribute copies of electronic designs or artwork Electronic designs are licensed to the original purchaser for use at one location 2014 Benartex Studios All rights reserved Of SD A New Leaf Pre cut appliqu files for use with BERNINA CutWork Accessory 21013 01 CWA For Use with the 21013 08 CWA For Use with the 21013 14 CWA For Use with the Bernina CutWork Accessory Bernina CutWork Accessory Bernina CutWork Accessory EE 1 Basting SON ancre 3600 EE 1 Basting SEM 3600 EE 1 Basting EST iseascrcasstsecaunsausansecacpscsdeyesnainusances tants 3600 mm 2 Bernina CutWork Appliqu Accessory Cut 1 Cut 1 mm 2 Bernina CutWork Appliqu Accessory Cut 1 Cut 1 mm 2 Bernina CutWork Appliqu Accessory Cut 1 Cut 1 mm 3 Bernina CutWork Appliqu Accessory Cut 2 Cut 2 mm 3 Bernina CutWork Appliqu Accessory Cut 2 Cut 2 mm 3 Bernina CutWork Appliqu Accessory Cut 2 Cut 2 mm 4 Bernina CutWork Appliqu Accessory Cut 3 Cut 3 mm 4 Bernina CutWork Appliqu Accessory Cut 3 Cut 3 mm 4 Bernina CutWork Appliqu Accessory Cut 3 Cut 3 mm 5 Bernina CutWork Appliqu Accessory Cut 4 Cut 4 mm 5 Bernina CutWork Appliqu Accessory Cut 4 Cut 4 mm 5 Bernina CutWork Appliqu Accessory Cut 4 Cut 4 21013 02 CWA For Use with the 21013 10 CWA For Use wi
17. lWork designs including rescaling rotating and mirror imaging 21013 31 DW A New Leaf 21013 31 CR A New Leaf 21013 31 PW A New Leaf Combo Draw File CrystalWork PaintWork 4 73 X 7 03 in 2 42 X 6 35 in 4 73 X 6 88 in 120 14 X 178 56 mm 61 47 X 161 29 mm 120 14 X 174 75 mm St L St L 8 500 St L NOTE Paint colors listed beginning with 4600 refer to Edding Textile Pens style 4600 The number following 4600 is the recommended pen color 21013 31 CR A New Leaf CrystalWork mm 1 Size SS6 108 Rinestones Lu mnuenpsensemnteninnvedvvdnabmtvevdjane Sapphire 21013 31 PW A New Leaf PaintWork mu 1 Green Details m mu rmrrrenssnmnmnemnemnemmemeeeneeeererserserrerrerverss 4600 4 GENERAL INSTRUCTIONS FOR USING MULTIPLE DESIGNWORKS COMPONENTS IN ONE DESIGN 1 Refer to the color information bar on your machine or your design instructions to determine the order in which you use traditional machine embroidery needle and thread or the Paint Work tool Paint Work files are denoted by PW at the end of a file name 2 Create any CrystalWork templates using the CrystalWork files and the CrystalWork tool following the CrystalWork Instructions These files are denoted by CR at the end of the file name The templates can be created either before or after the design is stitched but the crystals will be applied after the embroidery and or paint is completed Design contains a loose fill L Design is larger than 5 127 mm in either directi
18. lest size 16 Once all holes in the template are filled with the correct P f LA X via Sa inet 3 as LR 2 4 size crystals check to ensure that all crystals are facing up and that there are no stray crystals See Photo 8 Note Design pictured is for instructional purposes and is not 7 included in this collection It is a violation of Copyright law to make and distribute copies of electronic designs or artwork Electronic designs are licensed to the original purchaser for use at one location 2014 Benartex Studios All rights reserved Of SD A New Leaf Instructions 17 Cut a piece of rhinestone application tape slightly larger PHOTO 11 PHOTO 12 than the design 18 Remove the backing and place tape sticky side down over the crystal template See Photo 9 19 Smooth application tape over the top of each crystal using your fingertips or the rhinestone brush to ensure that all crystals are adhered to the tape 20 Slowly peel transfer tape away from the template The crystals should come up adhered to the tape See Photo 10 If individual crystals are loose or missing lay the tape carefully back down and re adhere crystals 21 Position the transfer tape with the crystals sticky side down onto your project See Photo 11 22 Place a press cloth over the transfer tape and press firmly with a hot iron for approximately 15 seconds If the transfer is larger than the iron move the iron to anoth
19. n either direction It is a violation of Copyright law to make and distribute copies of electronic designs or artwork Electronic designs are licensed to the original purchaser for use at one location 2014 Benartex Studios All rights reserved Of SD A New Leaf by Benartex Studios 21013 30 Designs Note Some designs in this collection may have been created using unique special stitches and or techniques To preserve design integrity when rescaling or rotating designs in your software always rescale or rotate designs using the handles directly on screen 21013 13 Leaf 2 21013 14 Leaf 3 Appliqu 21013 15 Leaf Accent 1 21013 16 Leaf Accent 2 2 86 X 3 17 in 1 83 X 2 58 in 2 24 X 2 86 in 2 30 X 2 64 in 72 64 X 80 52 mm 46 48 X 65 53 mm 56 90 X 72 64 mm 58 42 X 67 06 mm 8 522 St 3843 3 088 St 38 3 960 St 38 x 2 138 St 3 21013 17 Leaf Vine 1 21013 18 Leaf Vine 2 21013 19 Leaf Vine 3 21013 20 Leaf Vine 4 3 90 X 6 56 in 4 78 X 4 29 in 4 31 X 3 94 in 3 30 X 2 94 in 99 06 X 166 62 mm 121 41 X 108 97 mm 109 47 X 100 08 mm 83 82 X 74 68 mm 9 799 St BU L 7 230 St 38 7 119 St 2 4 408 St 385 21013 21 Feather Leaf 1 21013 22 Feather Leaf 2 21013 23 Appliqu Medallion 21013 24 Medallion 3 60 X 4 32 in 2 93 X 3 15 in 4 74 X 4 74 in 4 79 X 4 79 in 91 44 X 109 73 mm 74 42 X 80 01 mm 120 40 X 120 40 mm 121 67 X 121 67 mm TOG SE 4 631 St 3 11 190 St 381 25 944 St Design contains a loose fill L Design is larger th
20. on 13 Some white areas shown are not stitched S Design is smaller than 1 5 38 1 mm in either direction It is a violation of Copyright law to make and distribute copies of electronic designs or artwork Electronic designs are licensed to the original purchaser for use at one location 2014 Benartex Studios All rights reserved Of SD A New Leaf Instructions CRYSTALWORK INSTRUCTIONS 1 Remove upper thread from the machine 2 Attach the Straight Stitch CutWork Stitch Plate for your machine PHOTO 1 PHOTO 2 3 Remove the needle and replace with the correct size punch tool SS6 SS10 SS12 SS16 as noted on the Color Bar of the machine or in the crystal chart for the design collection with the flat side toward the back Tighten the needle clamp 4 Attach Presser Foot 48 5 Place the CrystalWork container on the stitch plate with the center positioning pin in the rear hole of the stitch plate 6 Attach the punch plate same size as the punch tool used PHOTO 4 on top of the container so that it sits flush with the top 7 Lower the punch tool by turning the handwheel to check that the container lines up correctly See Photo 1 8 Hoop parchment paper up side down and trim all excess from edges See Photos 2 and 3 9 Cut a piece of rhinestone template material slightly larger than the design Remove backing from the template material and place the sticky side down on the top of the parchment paper in the center of the hoop
21. oop to machine Continue stitching design until all appliqu pieces are placed and all stitching is complete PHOTO 4 NOTE Design pictured is for instructional purposes and is not included in this collection It is a violation of Copyright law to make and distribute copies of instructions or artwork Electronic designs are licensed to the original purchaser for use at one location 02014 OESD LLC All rights reserved
22. reen Detail 0352 8 Leaf Placement Stitch eeeeeeserseereeeeeee 0015 EM 9 Tackdown 5610 mm 10 Dark Green Detail 5934 21013 12 Leaf 1 A plig qu 1 Leaf Placement Stitch 0015 EH 2 Tackdown 5610 Mm 3 Dark Green Detail 5934 Em 4 Light Green Detail 6051 mu 5 Medium Blue Detail ceeeeeeeeeenees 4332 6 Light Blue Detail 4152 mm 7 Dark Blue Detail 4032 8 Pink Detail ii 2051 21013 13 Leaf 2 Em 1 Light Green Detail 6051 2 Pale Blue Detail ssoorvvrrrvvrrvrrnvrrrvrrrvrrrvrervrerveenn 4250 mn 3 Medium Green Detail 0352 Mm 4 Dark Green Detail 5934 Mm 5 Dark Blue Detail ceeeceeseeeeeneeenees 4032 Em 6 Medium Blue Detail 4332 7 Pink Dei nus ae 2051 21013 14 Leaf 3 Appliq qu 1 Leaf Placement Stitch ioorrrrrrrnvrnrvrrrvrrrvrernvenn 0015 EH 2 Tackdown 5610 Mm 3 Dark Green Detail 5934 Em 4 Light Green Detail 6051 mu 5 Medium Blue Detail 4332 Em 6 Dark Blue Detail eceeceseeeeeneeenees 4032 T Pink Detail ii 2051 21013 15 Leaf Accent 1 mm 1 Light Green Detail 6051 Em 2 Medium Blue Detail 4332 3 Light Blue Dell nr 4152 4 Pink Detail eee ceecsesereeeesseereteesneenes 2051 mn 5 Medium Green Detail 0352 mu 6 Dark Green Detail 5934 21013 16 Leaf Accent 2 mm 1 Light Green Detail 6051 2 Light Blue Detail 4152 Em 3 Medium Blue Detail 4332
23. th the 21013 23 CWA For Use with the Bernina CutWork Accessory Bernina CutWork Accessory Bernina CutWork Accessory EE 1 Basting Se is 3600 EE 1 Basting SE 3600 EE 1 Basting SU anne 3600 mm 2 Bernina CutWork Appliqu Accessory Cut 1 Cut 1 mm 2 Bernina CutWork Appliqu Accessory Cut 1 Cut 1 mm 2 Bernina CutWork Appliqu Accessory Cut 1 Cut 1 mm 3 Bernina CutWork Appliqu Accessory Cut 2 Cut 2 mm 3 Bernina CutWork Appliqu Accessory Cut 2 Cut 2 mm 3 Bernina CutWork Appliqu Accessory Cut 2 Cut 2 mm 4 Bernina CutWork Appliqu Accessory Cut 3 Cut 3 mm 4 Bernina CutWork Appliqu Accessory Cut 3 Cut 3 mm 4 Bernina CutWork Appliqu Accessory Cut 3 Cut 3 mm 5 Bernina CutWork Appliqu Accessory Cut 4 Cut 4 mm 5 Bernina CutWork Appliqu Accessory Cut 4 Cut 4 mm 5 Bernina CutWork Appliqu Accessory Cut 4 Cut 4 21013 05 CWA For Use with the 21013 11 CWA For Use with the Bernina CutWork Accessory Bernina CutWork Accessory EE 1 Basting ES annees 3600 EE 1 Basting SUE iceccaccinns esinoutresaniianipuseseisasaniaiianaiecvatants 3600 mm 2 Bernina CutWork Appliqu Accessory Cut 1 Cut 1 mm 2 Bernina CutWork Appliqu Accessory Cut 1 Cut 1 mm 3 Bernina CutWork Appliqu Accessory Cut 2 Cut 2 mm 3 Bernina CutWork Appliqu Accessory Cut 2 Cut 2 mm 4 Bernina CutWork Appliqu Accessory Cut 3 Cut 3 mm 4 Bernina
24. the 830 will perform this task automatically Replace embroidery needle with the CutWork Accessory Replace embroidery foot with foot 44 If you do not have foot 44 you can leave foot 15 on the machine foot 44 will simply keep the cut fabric from flagging as much turn the dial on the CutWork tool as required Remove the hoop from the machine Gently remove cut appliqu piece trimming any thread that may have not been cut completely PHOTO 1 Repeat as needed for designs with multiple appliqu pieces TACKDOWN APPLIQU AND COMPLETE EMBROIDERY DESIGN Replace the embroidery needle and rethread the machine Replace the embroidery foot 15 Spray hoop sized piece of stabilizer that is appropriate for your project and adhere to wrong side of background fabric or project that is to be hooped Hoop fabtic project and stabilizer Attach hoop to machine Send the embroidery file to the machine this is not a CWA file Stitch design as normal following the thread changes on the provided thread chart stopping after each Appliqu Placement Stitch After stitching an Appliqu Placement Stitch take the precut appliqu pieces required and peel off the cutaway backing and the release paper revealing a sticky backing PHOTO 2 Remove hoop from machine but do not remove the fabric from the hoop Adhere precut appliqu piece evenly over the Appliqu Placement Stitch use pressure to make sure pieces stick well PHOTO 3 Reattach h
25. tinue your design 12 Refer to the color information on the machine s screen and insert a second pen following steps above if needed Tip after raising the pen guard wipe the tip of the pen with a white cloth before starting the color See Photo 2 13 Use an Iron to heat set the painted fabric following pen manufacturer s instructions It is a violation of Copyright law to make and distribute copies of electronic designs or artwork Electronic designs are licensed to the original purchaser for use at one location 2014 Benartex Studios All rights reserved Of SD A New Leaf Instructions GENERAL APPLIQU INSTRUCTIONS Print out the necessary pages from the PDF of the applique pattern s Mark the right side of the pattern pieces so you ll know which direction to lay the pattern on the fabric Lightly spray the wrong side of the pattern pieces with temporary adhesive spray and allow it to set for a few minutes Place the pattern pieces on the right side of the fabric and carefully cut them out PHOTO 1 Sew the placement stitch on your hooped fabric PHOTO 2 With the paper still stuck to the right side of the appliqu fabric spray the wrong side of the fabric with temporary spray adhesive Place the fabric inside the sewing placement stitch so that it matches the stitching line and then remove the paper pattern PHOTO 3 Sew the tackdown PHOTO 4 Sew the remainder of the design and repeat for any remaining pieces PHOTO 5 ee AE
Download Pdf Manuals
Related Search