Operators Manual
Contents
1. Page 10 of 12 o KANMED User Manual BB1 070 1 from structures objects and people a Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the Babybed is used exceeds the applicable RF compliance level above the Babybed should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as reorienting or relocating the Babybed gt Over the frequency range 150 kHz to 80 MHz field strengths should be less than 10 V m Recommended separation distances between portable and mobile RF communications equipment and the Babybed The Babybed is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled The customer or the user of the Babybed can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and the Babybed as recommended below according to the maximum output power of the communications equipment Rated maximum output power Separation distance according to frequency of transmitter of transmitter2. Kanmed Babywarmer is connected to mains power by its own cable 3 6 First cleaning The unit is factory clean but must be cleaned according to your hospital routines Please refer to section maintenance for cleaning before use with the first patient Page 4 of 12 o KANMED User Manual BB1 070 1 4 Handling and daily use 4 1 Foldable walls The side walls and the front wall are folded down by lifting them upward until the upper guide pin is visible then fold them down Note When you close the side wall check that nothing gets trapped 4 2 Moving the bed around Note Do not use the side walls for moving the bed Hold the corners to move the bed and to transport it longer distances Do not forget to unplug any cables Note Use a low bed height when transporting with a baby inside 4 3 Connecting the lifting column to the mains not for BB 3 For connection of the lifting column use the included mains cable NOTE The only way to break the power is to either disconnect the cable at the pillar or at the wall socket 4 4 Adjusting height not for BB 3 The height is adjustable by the pushbuttons on the front The lifting column has an overload protection that will not be activated under normal conditions Constantly adjusting height with heavy loads may activate the overload protection When the motor has cooled down the lifting column works as normal again Warning Do not block the movements when activating the elect
3. delay that the raising and lowering function is working correctly and that it makes no noise when operated e That the tilt function works correctly It should not make any noises e That the wheels are tightened to the stand and not damaged in any way that they roll without noise and that the wheels locking function works properly e That all screws are properly tightened especially the screws connecting the height adjusting pillar to the wheel base the screws on top of the pillar the screws holding the shelf and gas spring the clips holding the bolt for the bed surface 9 2 Adjusting the release of the gas spring By manoeuvring the release arm you press down the release pin at the top of the gas spring Adjust by releasing the gas spring from the pillar Start by taking away the small safety spring Make someone or something hold the bed Pull out the gas spring from the pillar Un tighten the locking nut by turning the gas spring you adjust the contact with the release arm 9 3 Changing side walls The easiest way to replace a side wall is to place it in its hanging down position insert one pin in the lower grove bend the wall and insert the other pin 9 4 Changing the side brackets The side wall brackets are screwed from the inside of the bed with two 2 screws at each corner 9 5 Changing the electrical control Always unplug the power before doing repair on the Babybed e Remove the two 2 Torx screws under the power inlet an
4. User Manual KANMED 2ABYBED Art no BB1 070 2 March 2007 CE Caution Please read this manual carefully Incorrect use may cause patient injury Manufactured by KANMED AB www kanmed se Distributed by KANMED BABYBED User Manual BB1 070 1 1 General DesCM Pp Ul ON sca casiaveasvanetensnepeciwmsatadenamepsdesmtad nuns suaystoacucessnraayataaguanadnuemesetoautana tare ss ZD e PIO 488 8 6 eee ee ten ee E E E AEE E A A 3 Preparations before USC sresresrrerrrrrrrrrrrrr rr rr RKA R RAR RR RR KKR KKR RR RR RR KKR ARR KKR KKR KKR KKR RR RR RR KKR KKR KKR KRA 4 Handling and daily USC ssrssrssssrsresrrarerrererrrr rskr RAK ARR KRA R RKA ARR KR ARR RR ARR RR EERE RR KR RR RR ESSER DESDE EERE RR RKA AA gt Cleaning and MalntenanCe massage nea ss NER HORNE RR AR e PROUD TE C TOO UM VO sade Nan un ses E rr NN Nr Msn a Mg bro kr nn PR ARN AN etan Z Warranty Statement Mss ec aetna ses a Re AEE ET AR E ET Ar RE AR RR R Or FECRI Call Da Echnpancmncnccstautenonsen tie de a nes E A NN Na A RN SR FANNS KONER NN SNS 9 Technical service ANd maintenance ssssemssssssrsrrsr s rar s rsk ARAK RAR RAR ARAKRARRAR ARR A RAK RAR RAR AR RK RR SSSR ARK RA RAA 10 Spare PartsS ACCESSOSIOS ssssssssresesrererrsrrrrnrrrr nr eee ARR R ARR R RAK ARR K RAR RKA RR KR ARR KRA KRK RAR RR RR KRK RR KRK KRK RR EES LLENG OUGGIINCE iarsira ee a NS ar a ER ON NNE NER NN AR NR Et KANMED BABYBED TWIN VERSION AND FIXED HEIGHT VERSION Page 2 of 12 o KANMED Us
5. d slide the power supply out of the box and detach the spiral cable from the connectors e Remove the two screws Philips under the remote control and slide the unit by pulling it gently out from the front of the bed 9 6 Changing the pillar Disconnect power Remove the two 2 Torx screws under the power inlet and slide the power supply out of the box and detach the spiral cable and the pillar cable from the connectors Loosen the gas spring as described in 9 2 Remove the pin that holds the bed to the pillar and take away the bed Remove the bed holder from the top of the pillar Loosen the 6 screws that hold the pillar to the wheel base Mount the new pillar Connect the cables and test run the new pillar Rebuild the bed again Make sure that all screws are properly tightened Page 8 of 12 KANMED 10 Spare parts Accessories User Manual BB1 070 1 EE FIN Arr Te ENT VINN pr TR TER RR 700 0727 Tent Pole rr 700 0717 Silicon corner handle Ordered by the piece BB 20 Foam mattress For BB 1 and BB 3 Foam mattress sealed easy to clean 650 x 440 x 40 mm BB 21 Tent for BB 1 Please check with your local supplier or on the KANMED homepage www KANMED se for colours available NOTE Other accessories may be available Please check with your local supplier or on the KANMED homepage www kanmed se Please contact your supplier for a price list 11 EMC guidelines Guidance and manufacturer s declaration electromagnetic emiss
6. e or ceramic tile If floors are covered with synthetic material the relative humidity should be at least 30 Mains power quality should be that of a typical commercial or hospital environment KANMED Surge IEC 61000 4 5 Voltage dips short interruptions and voltage variations on power supply input lines IEC 61000 4 11 Power frequency 50 60 Hz magnetic field IEC 61000 4 8 1 kV differential mode 2 kV common mode lt 5 Ur gt 95 dip in Ur for 0 5 cycle 40 Ur 60 dip in Ur for 5 cycles 70 Ur 30 dip in Ur for 25 cycles lt 5 Ur gt 95 dip in Ur for 5 sec 1 kV differential mode n a for common mode lt 5 Ur gt 95 dip in Ur for 0 5 cycle 40 Ur 60 dip in Ur for 5 cycles 70 Ur 30 dip in Ur for 25 cycles lt 5 Ur gt 95 dip in Ur for 5 sec NOTE Ur is the a c mains voltage prior to application of the test level Guidance and manufacturer s declaration electromagnetic immunity User Manual BB1 070 1 Mains power quality should be that of a typical commercial or hospital environment Mains power quality should be that of a typical commercial or hospital environment If the user of the Equipment or System requires continued operation during power mains interruptions it is recommended that the Equipment or System be powered from an uninterruptible power supply or battery Power frequency magnetic fields
7. er Manual BB1 070 1 1 General Description The intended use of the Kanmed Babybed is to provide an ideal bed for premature and new born babies in hospital It is also intended to be used with the Kanmed Babywarmer system It is designed for hospital use only and must be used according to the instructions given in this manual according to your established clinical routines and by qualified personnel Only persons that have been instructed in the use of the Kanmed Babybed shall be allowed to use the product Warning Do not use the Kanmed Babybed with babies small children that are capable to move so much that they might fall climb out of the bed Do not leave a baby unattended with the side walls down Respect the weight limits Do not place electronic equipment on the shelf under the bed 2 Description of Symbols Maximum Load permitted Bed surface for BB 1 and BB 3 10 kg Excl BABYWARMER Control Unit 3kg and Water mattress 4 5kg Bed surface BB 4 10 kg Excl Two BABYWARMER Control Unit 2x3kg and two Water mattresses 2x4 5kg or one BABYWARMER Control Unit 3kg and twin water mattress 9kg Shelf under bed surface 10 kg Top shelf 5 25 mm Side poles to top shelf 5 kg on each Horizontal bars top shelf system 10 kg Storage box system 10 kg Read users manual before use Symbol for raising and lowering the bed not for BB 03 Symbol for tilt function Fulfils MDD 93 42 EEC AC current not for BB 3 Protect
8. ion grade Type B Body not for BB 3 wW C Approval symbol for the USA and the Canadian Markets gt US when the Babybed reached end of life it should be returned to the distributor for recycling in accordance with the EU 2002 96 EC WEEE directive if applicable Page 3 of 12 o KANMED DIDEI User Manual BB1 070 1 3 Preparations before use 3 1 Mounting of the Wheels Lay down the unit carefully on its side Be careful not to damage the side walls Note that the lockable wheels shall be mounted on the long legs Use the enclosed Allen key and tighten hard Be careful not to damage the paint Raise the unit to an upright position 3 2 Side Walls If sidewalls are not mounted then please see section Service Raise the sidewalls gently and slide them into place and remove the protection film 3 3 Tent pole Tent and Mattress Mount the tent pole in the rear bracket The Tent has a channel inside Thread the Tent pole into the channel in order to secure it Place the mattress in the bed 3 4 Check all bolts and screws Make sure that all bolts and screws are properly tightened and that the bed feels stable Run the electrical bed up and down and ensure that it moves smoothly without any unusual noise 3 5 Kanmed Babywarmer The Kanmed Babywarmer control unit is hung on its bracket under the bed The heating pad cable is preferably thread through one of the holes in the bed and connected to the control unit The
9. ions The Babybed is intended for use in the electromagnetic environment specified below The customer or the user of the Babybed should assure that it is used in such an environment RF emissions CISPR 11 RF emissions CISPR 11 Harmonic emissions IEC 61000 3 2 Voltage fluctuations flicker emissions IEC 61000 3 3 Electromagnetic environment guidance The Babybed uses RF energy only for its internal function Therefore its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment The Babybed is suitable for use in all establishments including domestic establishments and those directly connected to the public low voltage power supply network that supplies buildings used for domestic purposes Guidance and manufacturer s declaration electromagnetic immunity The Babybed is intended for use in the electromagnetic environment specified below The customer or the user of the Babybed should assure that it is used in such an environment Immunity test Electrostatic discharge ESD IEC 61000 4 2 Electrical fast transient Burst IEC 61000 4 4 IEC 60601 test level 6 kV contact 8 kV air 2 kV for power supply lines 1 kV for input output lines Compliance level 6 kV contact 8 kV air 2 kV for power supply lines n a for input output lines Page 9 of 12 Electromagnetic environment guidance Floors should be wood concret
10. m 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2 5 GHz For transmitters rated at a maximum output power not listed above the recommended separation distance d in meters m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer Note 1 At 80 MHz and 800 MHz the separation distance for the higher frequency range applies Note 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people Page 11 of 12 KANMED AB Gardsfogdevagen 18B SE 168 66 BROMMA Stockholm Sweden Telephone 46 8 56 48 06 30 Telefax 46 8 56 48 06 39 E Mail info kanmed se Home page www kanmed se Distributed by
11. o the user and or service manual and that the unit has not been modified or changed in any way or for any reason Products carries the CE mark Conforms to UL 60601 1 Certified to CAN CSA C22 1 No 601 1 EMC The Kanmed Babybed contains no electronics sensitive to EMC Highly sensitive equipment connected to the same electrical outlet as the Kanmed Babybed may be affected by the lifting column electrical motor The motor may generate a moderate amount of flicker during start Environmental data In use 10 to 400C lt 85 RH Transport 20 to 60 C non condensing Lifting column limitations Observe that the total load in the bed surface is limited to 10kg BABYWARMER system and water mattress not included The electrical motor in the lifting column is not designed for continues use Continued operation should be limited to 2 min max 5 cycles per minute Page 7 of 12 o KANMED User Manual BB1 070 1 9 Technical service and maintenance NOTE All spare parts used for replacement or repairs shall be supplied by KANMED or its authorised distributor Use of non KANMED permitted parts automatically transfers all safety responsibilities to the hospital Only qualified personnel shall attempt repairs 9 1 Annual checks Check the following at least once a year e That cables and connectors free of defects e Test the foldable sides for cracks or damages e That the switch for pillar height control responds without
12. of warranty reach of contract negligence or any other legal theory Page 6 of 12 o KANMED User Manual BB1 070 1 8 Technical Data BB 1_Standard BB 4 Twin BB 3 Fixed height Outer 760mm x 560mm 850x700mm 760mm x 560mm dimensions Bed surface Inner dims Inner dims Inner dims 665mm x 445mm 765mmxX640mm 665mm x 445mm po Min 700mm Min 700mm fa fr Front wheels with brakes Front wheels with brakes Front wheels with brakes Se Roller bearings Roller bearings Roller bearings Mattress Polyurethane with PVC Polyurethane with PVC Polyurethane with PVC cover 665x445x30mm cover 7 65x640x30mm cover 665x445x30mm 100 Bedton Washable 100 Bedton Washable 100 Bedton Washable 60 C 60 C 60 C Shelf Min 400mm x 400mm Min 400mm x 400mm Min 400mm x 400mm Fuses NANA S O Used standards SS EN 60601 SS EN 60601 fF gt Modifications Any modifications on Kanmed Babybed including home made accessories will void KANMED s responsibilities totally and are not allowed without written consent of KANMED Creating Systems Any person connecting the Kanmed Babybed to any other systems mains socket may have created a system according to IEC 60601 1 section 16 and must be qualified to evaluate any consequences that may harm staff patient and equipment Expected Lifetime Kanmed warrants a safe lifetime of 10 years from first day of use This is under the condition that the unit has been serviced according t
13. rical height adjustment When changing height make sure that no person cable or other items prevents the movement and that no cable is jammed or wrapped between the pillar and the wheelbase Blocking the movement can damage the pillar and void warranty 4 5 Tilting When tilting the bed press the release handle upward or downward to release the bed At the same time press the bed s corner upward or downward till the desired tilt is achieved The release handle can be reached and manoeuvred from both sides of the bed 4 6 Accessories Note Only use accessories approved by KANMED Respect the load limits Page 5 of 12 KANMED User Manual BB1 070 1 5 Cleaning and Maintenance Recommended controls Executed b Time schedule Additional information Cleaning of the bed Hospital routines Use a surface cleaning and disinfecting agent recommended by your internal hygienist Note KANMED Baby Warming Bed must under no circumstances be showered with any fluid Do not clean it in disinfecting chambers Cables and connectors Every day Make sure that they are in good condition Hospital routines See label on Mattress edge Hospital routines See label tent See label tent ic o cll manual adjustments ear 6 Trouble shooting Symptom Possible cause JAR The lifting column does not move No mains Check the cables as wanted not for BB 3 Something blocking the Check that nothing blocks movemen
14. should be at levels characteristic of a typical location in a typical commercial or hospital environment The Babybed is intended for use in the electromagnetic environment specified below The customer or the user of the Babybed should assure that it is used in such an environment IEC 60601 test level Compliance Electromagnetic environment guidance level Immunity test Portable and mobile RF communications equipment should be used no closer to any part of the Babybed including cables than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter Recommended separation distance d 1 2VP 3 Vrms 150 kHz to 80 MHz Conducted RF IEC 61000 4 6 Radiated RF IEC 61000 4 3 3 V m 80MHz to 2 5GHz d LNP 80 MHz to 800 MHz d ap 800 MHz to 2 5 GHz where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer and d is the recommended separation distance in meters m Field strengths from fixed RF transmitters as determined by an electromagnetic site survey should be less than the compliance level in each frequency range Interference may occur in the vicinity of equipment marked with the following symbol GY NOTE 1 At 80MHz and 800MHz the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflected
15. t Electrical connection broken or Technical service not properly connected You can not tilt the bed properly Control is out of order or needs Technical service It gets stuck in utmost positions adjustment It does not keep the position Something is blocking it Check that nothing blocks it Bed feels unstable Loose screws or wheels Height adjustments makes Technical service unusual noises 7 Warranty Statement KANMED warrants the purchaser that the Babybed is free from defects in materials and workmanship for a period of 12 month from the date of delivery The sole obligation of KANMED with respect to any such defect is limited to the repair with new or re manufactured parts or at the discretion of KANMED replacement of the equipment or refunding of the purchase price This warranty shall not apply if the product has been modified adjusted or repaired other than by KANMED or by organisations authorised by KANMED or modified adjusted or repaired not in accordance with written instructions provided by KANMED Neither shall the warranty apply if the equipment has been subject to misuse negligence or accident These warranties are made on the condition that prompt notification of a defect is given to KANMED or its authorised dealers within the warranty period KANMED shall have the sole right to determine whether a defect exists KANMED shall not in any case be liable for special or consequential damages arising from the breach
Download Pdf Manuals
Related Search