LS1502 LS1502A LS1202M LS1202MA LS1502M LS1502MA
Contents
1. e For optimal headroom select an amplifier with a power capacity equal to or up to double the rated program power capacity of the loudspeaker system e Ensure all amplifiers are supplied and connected to properly rated AC power cir cuits Underpowering amplifiers may cause premature clipping distortion SPEAKER CABLES Use either Carvin s professional speaker cable for up to 50 or high current 12GA Twist Lock cables for lengths up to 150 18GA cables are not recomended You can DAISY CHAIN up to one additional speaker per cable by using the OUTPUT connector Be sure the total impedance to the to the presence of important operating amplifier is not lower than the amplifier s minimum impedance dangerous voltage within A and maintenance A products enclosure servicing instructions in the literature that may be of a pe to constitute a risk of electric shoc to persons accompanying the appliance This symbol is intended to alert the user to the presence of uninsulated This symbol is intended to alert the user CAUTION RISK OF ELECTRIC SHOCK IMPORTANT FOR YOUR PROTECTION PLEASE READ THE FOLLOWING WATER AND MOISTURE Appliance should not be used near water near a bathtub washbow l sink laundry tub in a wet basement near a swimming pool etc Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings POWER SOURCES The product should be connected2. SAN DIEGO CALIFORNIA 1 3 5 SUBWOOFER CROSSOVER CONNECTIONS non powered models 1 1 4 INPUT from power amp output 2 Twist Lock INPUT from power amp Note the Twist Lock pin configeration is 1 LF Positive 1 LF Negative 2 not connected 2 not connected Crossover Bypass mode switch to bypass internal crossover must use active crossover when in bypass mode Twist Lock THROUGH wired in parallel with Twist Lock INPUT 1 4 THROUGH wired in parallel with 1 4 INPUT TWIST LOCK CONNECTOR WIRING Stripped wires 1 4 a Strip cable insulation back 3 4 Slip Securing Hub then Cable Clamp over cable before attaching wires Connection Configuration Black 1 positive White 1 negative Red 2 positive Green 2 negative Solder wires in contacts or use hex screws provided ps y ter Ea Thwiist Loek Hiowsing Serupa LIMITED WARRANTY Your Carvin Audio loudspeaker is guaranteed against failure for 5 YEARS unless otherwise stat ed Carvin Audio will service and supply all parts at no charge to the customer providing the unit is under warranty Shipping costs are the responsibility of the customer CARVIN AUDIO DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN A COPY OF THE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY Carvin Audio assumes no responsibility for horn drivers or speakers damaged by this unit This warranty does not cover and no liability is assume
3. Maximum SPL 128dB peak Crossover Frequency 80Hz 120Hz or Bypass Speaker Protection Active Limiter Connectors one XLR Male one XLR Female one 1 4 TRS jack AC Power Requirement 90 250VAC 50 60Hz 600VA
4. input note if this switch is left IN signals from a mixer will be distorted Press this switch IN to add 30dB of gain to the XLR and 1 4 inputs of INPUT 1 so that a microphone can be used 3 LEVEL CONTROLS The LINE MIC 1 INPUT 2 and INPUT 3 level controls adjust the volume of each input 4 INPUT 2 This input is designed with a high impedance gt 100K ohms for instruments such as a guitar Other sources such as keyboards or drum machines can also be connected 5 INSTRUMENT SWITCH Press the switch IN to provide an alternate tone for instruments on INPUT 2 6 INPUT 3 The RCA jacks are inputs for MP3 players CD players keyboards and DJ mixers The two input signals are combined into a mono signal For stereo operation a second active speaker is required with the Left signal going to one speaker and the Right signal going to a second speaker 7 SHAPE SWITCH Press the switch IN to change the EQ on INPUT 3 useful for playback of pre recorded music 8 ACTIVE EQUALIZATION The active powered loudspeakers offer a 3 band mid sweep equalizer for custom tuning to the acoustical environment The EQ system is engineered specifically for the active powered loudspeakers featuring a modest boost and cut range of 6dB to prevent radical adjustments that could otherwise compromise the system The Mid band sweep is particularly useful for enhancing critical mid range frequencies for stage moni toring or for cutting
5. CaARvNAUDIO LS Series Loupspeakers USER MANUAL LS1202M LS1502M LS1202MA LS1502MA LS1502 LS1503 LS1502A LS1801 LS1801A LS2153 LS1802 76 15230H 070815 The LS Series from Carvin Audio are one of the best loud speaker values on the market today offering superb sound at high output levels Your audience will appreciate the crystal clear highs high intelligibility in the vocal range and deep solid bass making all the difference in your performance Building upon the company s long standing reputation for great sonic performance coupled with proven reliability and solid value the LS Series loudspeakers deliver all the features musicians and mobile DJs demand Encompassing main and monitor 2 way systems 3 way sys tems and subwoofer systems with active and passive models the LS Series is ideally suited to address a wide range of sound reinforcement system requirements from intimate clubs to large scale high impact music venues With key features like twist lock and quarter inch connectors across all models steel grills to pro tect the drivers recessed steel handles for easy transport and high order low loss biampable crossovers that ensure accurate reproduction of music sources Carvin s LS Series loudspeakers are just what your audience has been waiting for The powered LS A speakers take the guesswork out of selecting the ideal power source to drive your LS loudspeakers The inter nal amplif
6. G MATERIALS In the event you have to re ship your unit always use the original carton and packing material CARVIN and the shipping company are not liable for any damage caused by improper packing SAVE YOUR INVOICE It will be required for warranty service if needed in the future SHIPMENT SHORTAGE If you find items missing they may have been shipped separately Please allow several days for the rest of your order to arrive before inquiring RECORD THE SERIAL NUMBER on the enclosed warranty card for your records Return the warranty card with your name and comments to us a V Al AUDIO 12340 WORLD TRADE DRIVE SAN DIEGO CA 92128 800 854 2235 CARVINAUDIO COM Powered Full Range LS1202MA LS1502MA LS1502A ACTIVE REAR PANEL USA SYSTEM EQ LOW MID MID SWEEP HIGH 0 wie 1kHz 0 g e i e J S J z e RS 43 2 7 C a Co be d amp i AN 3 6 6 100Hz 5kHz 6 6 7 INPUT 3 C wus CARVIN F an L 1202MA A 400 WATTS 0 10 SER No OD 12345 3 PROTE 5 A 4 3 2 B CERTIFIED N als oS Q 2 eS oe to c Ww Sty a 0 OUT MIX THRU 1 INPUT 1 XLR and 1 4 TRS JACK Use these as the primary input from a mixer or MIC see 2 Using an XLR or 1 4 TRS cable from a balanced source will reduce noise which may be picked up by the cable You may DAISY CHAIN as many powered systems as you wish see 13 2 MIC IN SWITCH Use the OUT position for normal line level mixer
7. certain frequencies to compensate for room resonances These controls affect all 3 inputs 9 PROTECT LED If the system should go into protect mode the YELLOW LED will light and the power amps will shut off This may occur if a the system is overheated due to clipping the power amps for an extended period of time b one of the internal drivers developed a short or c the power amps require service 10 CLIP LED The RED CLIP LED will flash if an internal power amp start to distort Turn the LEVEL controls down to avoid distortion Damage to the drivers can result from operating at a level where the RED CLIP LED is constantly illuminated 11 POWER SWITCH and LED Push this switch to the ON position to apply power to the unit The blue POWER LED will light to show the system is on Power up your mixer first then turn on the LS active speaker When shutting down turn the LS active speaker off first then turn off the mixer 12 AC POWER Use a standard grounded AC cord Whenever possible use dedicated circuits for powered speakers 13 OUTPUT XLR Use the second XLR to link as many active powered systems as you wish see 14 14 OUT MIX THRU SWITCH for daisy chaining additional systems Press the switch IN for a direct PARALLEL connection to INPUT 1 only use with external mixer and for daisy chaining other powered systems With the switch in the OUT position the combination of all 3 channels including the EQ are se
8. d for damage due to natural disasters accidents abuse loss of parts lack of reasonable care incorrect use or failure to follow instructions This warranty is in lieu of all other warranties expressed or implied No representative or person is authorized to represent or assume for Carvin any liability in connection with the sale or servicing of Carvin Audio products CARVIN AUDIO SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES MAINTAINING YOUR EQUIPMENT Avoid spilling liquids or allowing any other foreign matter inside the unit The panel of your unit can be wiped with a dry or slightly damp cloth in order to remove dust and bring back the new look As with all pro gear avoid prolonged use in caustic environments salt air When used in such an environment be sure the amplifier is adequately protected SERVICE In the USA please go to www carvinaudio com under SUPPORT click on REPAIR INFORMATION Outside the USA contact your dealer or go to http www carvinaudio com click on DEALERS for your nearest service center Include a written description of the problem with serial number and date of purchase Specification System Type Frequency Response Coverage Pattern Crossover Crossover Frequency Power Full Range Cont Prog Peak Sensitivity 1W 1m Maximum SPL LF Driver HF Driver Nominal Impedance full range Bi amp LF Bi amp HF Suspension Mounting Connectors Dime
9. g Connectors Dimensions H x W x D 18 inch Sub bass reflex 29 Hz 265 Hz 10dB 35 Hz 150 Hz 3dB omni Low Pass 150 Hz 500W 1000W 2000W 98dB 125dB Cont 131dB Peak 18 inch woofer 8 Ohms Top 1 3 8 inch Pole Mount Cup Two NL 4 Twist lock Two 1 4 TS jacks 23 5 in x 19 75 in x 22 75 in 600 mm x 505 mm x 580 mm Dual 18 inch Sub bass reflex 24 Hz 265 Hz 10dB 30 Hz 150 Hz 3dB omni Low Pass 150 Hz 1000W 2000W 4000W 101dB 131dB Cont 137dB Peak Dual 18 inch woofers 4 Ohms none Two NL 4 Twist lock Two 1 4 TS jacks 23 5 in x 40 in x 22 75 in 600 mm x 1020 mm x 580 mm Net Wt 69 Ib 31 kg 122 Ib 55 kg Optional Accessories CVS1801A cover CVS1802A cover Specification for Active Models LS1202MA LS1502MA LS1502A LS1801A SAME AS PASSIVE MODEL EXCEPT Internal Amplifier 400Watts Maximum SPL 124dB peak Crossover Frequency 2 5 kHz Speaker Protection Active HF amp LF Limiter Connectors one XLR Male one XLR Female two 1 4 TRS jacks two RCA jacks AC Power Requirement 90 250VAC 50 60Hz 300VA SAME AS PASSIVE MODEL EXCEPT Internal Amplifier 400Watts Maximum SPL 128dB peak Crossover Frequency 2 5 kHz Speaker Protection Active HF amp LF Limiter Connectors one XLR Male one XLR Female two 1 4 TRS jacks two RCA jacks AC Power Requirement 90 250VAC 50 60Hz 300VA SAME AS PASSIVE MODEL EXCEPT Internal Amplifier 1400Watts
10. iers are perfectly mated with the loudspeaker systems making setup and operation easier with less gear to haul Active full range systems feature 3 channel operation allowing use as a standalone PA system with seperate inputs levels for combining music sources mixer mic instrument mic MP3 phone a mix thru switch on the XLR output and a 3 band EQ with mid sweep frequency Active subwoofers feature a selectable active cross over at 80Hz or 120Hz with switchable high pass on the XLR output Class D operation and switchmode technology keep the amp modules cool running and lightweight Built in limiters help prevent clipping distortion and protect drivers Going one step further all LS Series loudspeaker enclosures utilize cross grain laminated multi ply hardwood construction Why is this important Unlike other materials multi ply hardwood construction results in a lightweight rigid enclosure with reduced flex and sonic coloration caused by cabinet resonance and the added benefit of a more structurally robust enclosure designed to handle the rigors of the road The rugged black Duratuff cover ing adds another layer of protection from dents and scrapes The Carvin Audio LS Series loudspeakers look every bit as compel ling as they sound RECEIVING INSPECTION INSPECT YOUR LOUDSPEAKER FOR DAMAGE which may have occurred dur ing shipping If damage is found please notify the shipping company amp CARVIN SAVE THE CARTON amp ALL PACKIN
11. ith larger speakers SEE 9 10 11 12 above for LED indicators and AC power Passive Non Powered Models CONNECTOR PINOUT FULL RANGE A U 1 4 Phone Jack Tip Pos Sleeve Neg Speakon 1 Pos 1 Neg 2 2 Not Connected Mode Speakon Only Speakon 1 LF Positive 1 LF Negative 2 HF Positive MF HF 2 HF Negative MF HF 1 4 Phone Jack Tip LF Pos Sleeve LF Neg MADE IN THE Ruore Professional Sound Reinforcement Loudspeaker System LS1503 400W CONTINUOUS 800W PROGRAM 1600W PEAK MADE IN USA THROUGH MP sale Only CARVII CORP SAN DIEGO CALIFORNIA 1 2 5 MULTI WAY CROSSOVER CONNECTIONS non powered models Use 1 4 or Twist Lock cables for connecting to the power amp and daisy chaining to additional speakers For high powered and biamp applications use Twist Lock cables only 1 1 4 INPUT from power amp output full range input only 2 Twist Lock INPUT from power amp full range or biamp Note the Twist Lock pin configuration for biamping is 1 LF Positive 1 LF Negative 2 MF HF Positive 2 MF HF Negative 3 Full Range Biamp mode switch 4 Twist Lock THROUGH wired in parallel with Twist Lock INPUT 5 1 4 THROUGH wired in parallel with 1 4 INPUT SUGGESTIONS FOR OPTIMAL PERFORMANCE e To help control feedback and to correct for venue characteristics use a graphic EQ e For optimal coverage and dispersion elevate the high frequency horns above eye level
12. nsions H x W x D Net Wt Optional Accessories LS1202M 12 inch 2 Way bass reflex 70 Hz 20 kHz 10dB 76 Hz 18 kHz 3dB 90H x 60V 2 Way with Speaker Guard 2 5 kHz 300W 600W 1200W 97dB 122dB Cont 128dB Peak 12 inch woofer 1 inch titanium 8 Ohms 8 Ohms 300W 600W 1200W 16 Ohms 50W 100W 200W none Two NL 4 Twist lock Two 1 4 jacks 22 75 in x 15 5 in x 14 75 in 580 mm x 395 mm x 375 mm 33 Ib 15 kg CVS1202MA cover LS1502M 15 inch 2 Way bass reflex 47 Hz 20 kHz 10dB 18 kHz 3dB 90H x 60V 2 Way with Speaker Guard 2 5 kHz 400W 800W 1600W 100dB 126dB Cont 132dB Peak 15 inch woofer 1 inch titanium 8 Ohms 8 Ohms 400W 800W 1600W 16 Ohms 50W 100W 200W none Two NL 4 Twist lock Two 1 4 TS jacks 25 75 in x 18 5 in x 15 75 in 655 mm x 470 mm x 400 mm 44 Ib 20 kg CVS1502MB cover LS1502 15 inch 2 Way bass reflex 47 Hz 20 kHz 10dB 53 Hz 18 kHz 3dB 90H x 60V 2 Way with Speaker Guard 2 5 kHz 400W 800W 1600W 100dB 126dB Cont 132dB Peak 15 inch woofer 1 inch titanium 8 Ohms 8 Ohms 400W 800W 1600W 16 Ohms 50W 100W 200W 1 3 8 inch pole mount cup Two NL 4 Twist lock Two 1 4 TS jacks 25 75 in x 18 5 in x 11 75 in 655 mm x 470 mm x 300 mm 44 Ib 20 kg CVS1502B cover Specification System Type Frequency Response Coverage Pattern Crossover Crossover Frequency Power F
13. nt to the OUTPUT XLR This unit becomes the master source for other powered systems connected to the OUTPUT XLR Powered Subwoofer 4 INPUT 1 XLR and 1 4 TRS JACK Use these as the primary input from a mixer Using an XLR or 1 4 TRS cable from a balanced source will reduce noise which may be picked up by the cable You may daisy chain as many powered systems as you wish see 3 2 LEVEL CONTROL Adjust the overall volume of the subwoofer 3 OUTPUT XLR Use the second XLR to link as many active powered systems as you wish see 4 4 HIGH PASS OUTPUT SWITCH LS1801A ACTIVE REAR PANEL MN CARVIN W LS1801A POWERED SUBWOOFER HE HIGH PASS 700W RMS USA FULL THRU 1400W PEAK e SER No OD 12345 The HIGH PASS switch changes the signal at XLR THRU from FULL range parallel with LE iee TAE ee Input to HIGH PASS output all frequencies above the 120Hz 80Hz crossover switch BYPASS setting o This is useful for going to amplified top cabinets that can not handle the sub s low 90 230VAC A 50 60iiz frequencies hea 5 CROSSOVER BYPASS SWITCH The crossover bypass switch bypasses the internal active crossover allowing the use of an outboard active crossover 6 CROSSOVER FREQUENCY SWITCH The CROSSOVER FREQUENCY switch selects the highest frequency to produced by the subwoofer The 120Hz OUT setting is generally used with small to mid sized speakers in your setup The 80Hz IN setting is generally used w
14. to a power supply only of the type described in the operating instructions or as marked on the appliance GROUNDING OR POLARIZATION Precautions should be taken so that the grounding or polarization is not defeated POWER CORD PROTECTION Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs SERVICING The user should not attempt to service the appliance beyond that described in the operating instructions All other servicing should be referred to qualified service personnel FUSING If your unit is equipped with a fuse receptacle replace only with the same type fuse Refer to replacement text on the unit for correct fuse type SAFETY INSTRUCTIONS EUROPEAN The conductors in the AC power cord are colored in accordance with the following code GREEN amp YELLOW Earth BLUE Neutral BROWN Live U K MAIN PLUG WARNING A molded main plug that has been cut off from the cord is unsafe NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAIN PLUG INTO A POWER SOCKET MADE IN THE Ruore Professional Sound Reinforcement Loudspeaker System LS1801 500W CONTINUOUS 1000W PROGRAM 2000W PEAK MADE IN USA CONNECTOR PINOUT 1 4 PHONE JACK TIP POS SLEEVE NEG SPEAKON 1 POS 1 NEG 2 2 NOT USED INTERNAL LOW PASS CROSSOVER THROUGH Q L at i CARVII CORP
15. ull Range Cont Prog Peak Sensitivity 1W 1m Maximum SPL LF Driver MF Driver HF Driver Nominal Impedance full range Bi amp LF Bi amp MF HF Suspension Mounting Connectors Dimensions H x W x D LS1503 15 inch 3 Way bass reflex 46 Hz 20 kHz 10dB 52 Hz 18 kHz 3dB 90H x 60V 3 Way with Speaker Guard 500Hz amp 3 3 kHz 400W 800W 1600W 101dB 127dB Cont 133dB Peak 15 inch woofer 6 inch mid 1 inch titanium 8 Ohms 8 Ohms 400W 800W 1600W 8 Ohms 200W 400W 800W 1 3 8 inch pole mount cup Two NL 4 Twist lock Two 1 4 jacks 28 75 in x 18 75 in x 15 in 730 mm x 480 mm x 380 mm LS2153 Dual 15 inch 3 Way bass reflex 45 Hz 20 kHz 10dB 51 Hz 18 kHz 3dB 90H x 60V 3 Way with Speaker Guard 350Hz 2 5 kHz 800W 1600W 3200W 101dB 130dB Cont 136dB Peak 15 inch woofer mids 15 inch woofer 1 inch 1 5 Dia titanium 4 Ohms 4 Ohms 800W 1600W 3200W 16 Ohms 50W 100W 200W none Two NL 4 Twist lock Two 1 4 TS jacks 43 75 in x 16 5 in x 15 in 1110 mm x 420 mm x 380 mm Net Wt 58 Ib 26 4 kg 73 Ib 33 kg Optional Accessories CVS1503A cover CVS2153A cover Specification LS1801 LS1802 System Type Frequency Response Coverage Pattern Crossover Crossover Frequency Power Full Range Cont Prog Peak Sensitivity 1W 1m Maximum SPL LF Driver Nominal Impedance full range Suspension Mountin
Download Pdf Manuals
Related Search