Telit RoadStar Installation Guide
Contents
1. La Telit Installing GPS Antenna 5 8 1 Where to Locate the Antenna The preferred location for the antenna is on the bottom right side of the dashboard s Note In vehicles with air bags on the beam where the antenna cable passes the antenna cable should be directed behind or beside the airbag 5 8 2 e Co M 5 8 3 Installing the Antenna Thoroughly clean the location intended for installation using a cloth and detergent Allow the spot to dry before you continue Carefully remove the protective film from the 3M adhesive Locate the antenna on the cleaned location Carefully press the antenna toward the dashborad Ensure all corners of the antenna are attached to the dashboard Possible positions Mounting instructions Telit 5 8 4 Installing the Coaxial Cable 5 Direct the antenna s coaxial cable along the car beam Ensure the antenna cable does not get damaged 6 When completing the cables installation and reaching close to the device coaxial cables SMA female connector attach both connectors together 7 Roll the remaining cable 8 Examine the antenna and cables properly installed Mounting instructions L Telit Installing the SIM card See SIM card installation position Note Insert the SIM card when the phone is off Mounting instructions l Telit 5 10 Installing Privacy Handset and Holder 1 Attached the holder base to car dashb2. of the main console at the front of the console in a location where it would not bother the driver or passengers but would sound best 5 4 2 Installing the Speaker 1 Install the speaker at the right side of the main console at the front of the console mm 2 I the screws connecting the a speaker to the hanger N gt Install the hanger using the 2 tin screws Direct the speaker cable behind the mat located at the bottom of the car Ensure the cable does not interfere with the vehicle or its accessories operation O Di lt P Co Ensure the speaker cable is not exposed to damage by the passengers Mounting instructions Telit 5 5 Installing the Electrical Connections The electrical cable is provided separately from the control cable Before installation begins connect the four leads which include the 2A fuses using a red or blue crimp sleeve as appropriate Please note sharp edges or moving parts which may damage the wires Warning The value for the fuses provided with the kits must not be changed The kit is appropriate only for a 12V vehicle In case of converting any other kit model into this kit please change the power cable The electrical cables should be directed as follows e So as not to disturb the driver or passengers e So as not to pass near the car s sharp or moving parts The external voltage connection is located under the dash board or close to the fuse b
3. aker and microphone installed inbetween car roof and windscreen glass above the driver must face different directions Note Do not hide the speaker inside the dash board If you cover it sound quality will be lowered Note e Locate the speaker at the right side of the main console at the front of the console in a location where it would not bother the driver or passengers but would sound best Mounting instructions L Telit 5 Installing the Cradle and Phone x E Carphone unit Cradle Adjustable bracket 5 1 Where to Position Reminder The best way to determine the Phone s position to the customers full satisfaction is to locate it when the customer is beside you and obtain Note his her agreement e Please ensure the Phone s location does not interfere with the vehicle or its accessories operation it should not interfere with opening the glove compartment or ashtray should not prevent access to the lighter moving the gear stick operating the hand break etc Do not install the Phone in front of the vehicle s air bag This restriction must be adhered to as in the case of an emergency the air bag blows up Warning and can fail to work properly e Ensure the surface on which this Phone is installed is sufficiently strong to carry the weight and pressure which would be exerted on it e When selecting the Phone s location please ensure the control ca
4. ar roof and windscreen glass and away from external sources of noise e Install the microphone in a different direction than the speaker so as to avoid echo and ensure there is a distance of at least 1 5 meters between them Mounting instructions Telit 5 3 2 Installing the Microphone 1 Usingthe clip install the microphone inbetween the car roof and windscreen glass Direct the microphone cable along the roof behind it so as not to be seen Continue directing the microphone cable along the left beam on the driver side Direct the cable under the dash board to the connection point of the cable with the control cable connected to the Phone Ensure the microphone cable and antenna cable are kept away from each other Note Ensure the microphone cable is not in contact and does not interfere with the car pedals and steering wheel stick 5 Connect the microphone cable plug to the correct port on the control cable Mounting instructions L 3 Telit Installing the Speaker HR e Md 5 4 1 Whereto Locate the Speaker Reminder The speaker and microphone installed inbetween the car roof and windscreen glass above the driver must face different directions Note If the speaker and microphone face each other this will cause echo Do not hide the speaker inside the dash board If you cover it sound quality will be lowered Note e Locate the speaker at the right side
5. ble connected to it does not interfere with the vehicle or its accessories operation e Ensure it is safe and convenient to operate the Phone and read the display from the driver s seat Mounting instructions Telit e Ensure the Phone would be protected from direct sunlight and humidity air conditioner openings e Ensure the Phone would be protected from mechanical damage by the car s accessories 5 2 Installing the Cradle and Phone 1 Disassemble the cradle into its two parts 2 Install one of the cradle parts in the determined location in the car with 4 tin Screws If you are not able to locate the cradle properly please use a adjustable bracket from the station inventory Note 3 Install the second cradle part on the handsfree Phone using the 4 philips screws provided with this kit Only use the original screws provided with this kit Note 4 Connect the two cradle parts 5 Direct the control cable coming out of the Phone behind the car panel Mounting instructions Telit Installing the Microphone The microphone is provided with a clip which makes it possible to install it inbetween the car roof and windscreen glass 5 3 1 Where to Locate the Microphone Reminder e Install the handsfree Phone s microphone 30 40 cm away from where the driver speaks when he she is in their normal driving position e Itis recommended to install the microphone inbetween c
6. e red cable Replace fuse Tighten connection to power source Mounting instructions F Telit 7 Appendix Finding IMEI code 1 Type code 06 2 Find locking code 5625 Mounting instructions
7. e provided separately A Telit lutions 2 Installation Diagram Te Swivel FY Hp Privacy lt Mount i Handset lol Holder Optional ine Black A Active GPS Antenna Q No K Speaker CD 6 ar aa Microphone si Q0 Z to aU ZU EU N O D lt V 2A Fuse Mounting instructions Head Unit Antenna ML ue L Telit 3 Carphone layout Mounting instructions External auxiliary jack V olurre Keys Adjust speaker earpiece and ringer volume 2 2 Display 65k Color SIM Na igation Key and GPS Left Soft Key Right Soft OK Key Send Key for making and acc eptingc alls Voic email shortcut in Telit RoadStar without GPS o functionality GPS key will be replaced with OK key Pow er On off L e Telit 4 Preplanned Accessory Positioning Positioning of all accessories must be planned in advance before installation begins e Ensure that no wire braids go through locations where Phone accessories are to be installed e Ensure that any parts of the handsfree Phone will not interfere with the vehicle or its accessories operation 4 1 Plan Phone and Cradle Positions i Note The best way to determine the Phone s position to the customer s full satisfaction is to locate it when the customer is beside you and obtain his her approval e Please ensure the Phone s location does not interfere with the vehicle or its accessories operati
8. g order Replace microphone A Phone problem may exist Replace Phone Noise is heard Ask whether noise always occurs in specific geographical areas Explain that reception trouble sometimes occurs in transition between coverage areas Ask whether noise occurs when window is open Explain that the Phone is an amplifying system that receives all environmental noise and therefore it is preferable to speak with a closed window Check whether microphone and antenna are installed on the same side If they are install microphone as per the instructions Check whether eye contact exists between speaker and microphone If it does change location accordingly Check for improper voltage connection check whether voltages are connected as per instructions Change voltage source in accordance with instructions Phone switches on and off by itself Check minus connection Black wire connect minus to car body Check voltage contacts Tighten loose contacts Phone switches on and off by itself Check fuse Check connection to voltage source green cable Replace fuse Tighten connection to voltage source Ensure a 250V 2A fuse is used Phone does not switch off after switching off car Check connection to power source green cable Tighten connection to power source Phone does not switch off after switching off car Check connection to power source Check fus
9. l e Telit Telit RS Car Phone Installation Guide Mounting instructions l ie Telit Table of Content 1 Carphone kit 2 Installation Diagram 3 Carphone layout 4 Preplanned Accessory Positioning 4 1 Plan Phone and Cradle Positions 4 2 Plan the Microphone s Position 4 3 Plan the Speaker s Position 5 Installing the Cradle and Phone 5 1 Where to Position Reminder 5 2 Installing the Cradle and Phone 5 3 Installing the Microphone 5 4 Installing the Speaker 5 5 Installing the Electrical Connections 5 6 Installing the Voltage Cable 5 7 Installing RF Antenna 5 8 Installing GPS Antenna 5 9 Installing the SIM card 5 10 Installing Privacy Handset and Holder 6 Trouble Shooting 7 Appendix Mounting instructions Telit solutions solutions 1 Carphone kit Car phone unit Speaker Microphone Power supply and fuse Cables Cradle with screws Mounting instructions S Telit wireless solutions Optional Parts Description RF antenna GPS antenna Privacy Handset Optional Mounting instructions This High Efficiency Omnidirectional Antenna is designedforinside glass mountinstallations operating in the 800MHz cellular 900 MHz trucking 1800 MHz DCS 1900 MHz PCS and 2100 MHz UMTS bands using included 3M 5M adhesive and supplied with 3M 5M cable and SMA male connector ww GPS active antenna Handset is not supplied as part of the car kit It s an optional accessories and can b
10. oard or specific place in the back seat environment Additional metal bracket not supplied can be used Mounting instructions Telit 2 Insert the cradle to the holder base and secured it to make sure that it won t lift up during normal usage 3 Insert hanset to holder L To detach the handset from the holder push the handset up Note Mounting instructions Telit 4 Insert the external handset plug to the carphone jack 5 Secure the external handset cable with a plastic strip to the octopus cable 6 Make sure that the external handset plug is attached firmly to the carphone jack Mounting instructions L e Telit 6 Trouble Shooting Symptom No reception What to Check Check whether connector is correctly connected to the cable use an efficiency meter What to Do Replace connector Check if internal and external antenna base is correctly attached Attach antenna base Check proper working order of antenna cable Replace antenna cable Other party cannot be properly heard Check speaker s proper working order Replace speaker A Phone problem may exist Replace Phone Check speaker location Change location User is not heard by the other party Check microphone and contacts Tighten microphone connector to the Phone Check routing of microphone cable Change routing of microphone cable Check microphone s proper workin
11. on it should not interfere with opening the glove compartment or ashtray should not prevent access to the lighter moving the gear stick operating the hand break etc Warning Do not install the Phone in front of the vehicle s air bag This restriction must be adhered to as in the case of an emergency the air bag blows up and can fail to work properly e Ensure the surface on which this Phone is installed is sufficiently strong to carry the weight and pressure which would be exerted on it e When selecting the Phone s location please ensure the control cable connected to it does not interfere with the vehicle or its accessories operation e Ensure itis safe and convenient to operate the Phone and read the display from the driver s seat e Ensure the Phone would be protected from direct sunlight and humidity air conditioner openings e Ensure the Phone would be protected from mechanical damage by the car s accessories Mounting instructions Telit 4 2 Plan the Microphone s Position e Install the handsfree Phone s microphone 30 40 cm away from where the driver speaks when he she is in their normal driving position e Itis recommended to install the microphone inbetween car roof and windscreen glass and away from external sources of noise e Install the microphone in a different direction than the speaker so as to avoid echo 4 3 Plan the Speaker s Position The spe
12. ox depending on the car model Note In new vehicles a cellular phone connection can be found near the fuse box See the car s user s manual under Info Only use the kit s original fuses 250V 2A Mounting instructions wirel Telit ess solutions Installing the Voltage Cable Voltage battery Ignition GND The following chart covers the manner by which the voltage cable should be connected to the car s electrical system Mute Wire Color Function Must be connected to Ensure Red Includes fuse case To provide the handsfree Phone with fixed voltage 12V fixed voltage An additional fuse case is provided which must be connected to a fixed voltage source Ensure a 250V 2A fuse is used Includes fuse case phone after switching the ignition on and turn it off after car ignition is switched off voltage Black To provide a fixed Car body minus Ensure the connection minus point is on the car body only Use a cable shoe tin screw and springy disc Green To turn on the cellular 12V 24V Ignition Determine the correct point with a voltmeter Ensure a 250V 2A fuse is used Mounting instructions VA Telit 5 7 Installing RF Antenna 5 7 1 Whereto Locate the Antenna e The preferred location for the antenna is on the right side of the windshield e If other communication system is installed in the car plea
13. se locate the antenna as far as possible from the other phone antenna Recommended distance is 30cm s Some car vendors such as Renault feature a radiation filter on the windshield Note Therefore it is necessary to install the antenna on a side or back window Li In vehicles with air bags on the beam where the antenna cable passes the antenna cable Note should be directed behind or beside the airbag 5 7 2 Installing the Antenna 1 Thoroughly clean the location intended for installation using a cloth and detergent Allow the spot to dry before you continue Carefully remove the protective film from the 3M adhesive Locate the antenna on the cleaned location a Carefully press the antenna toward the window Ensure all corners of the antenna are attached to the window Chose the mounting position on the vehicle windshield according to bellow drawing AWN Note Please keep min 20 mm distance from metal surface Mounting instructions La L Telit 5 7 3 Possible positions 5 7 4 Installing the Coaxial Cable 1 Direct the antenna s coaxial cable along the car beam Ensure the antenna cable does not get damaged 2 When completing the cables installation and reaching close to the device coaxial cables SMA female connector attach both connectors together 3 Roll the remaining cable 4 Examine the antenna and cables properly installed Mounting instructions
Download Pdf Manuals
Related Search