User Manual Omega Altise
Contents
1. PORTABLE AIR CONDITIONER APC12 APC12RC amp 14 omega altise Contents EE 2 Idee GU CU EE 3 Features Of Your New Portable Air Conditioner 22422 3 Energy Saving TIDS E 3 SpecHicalioh EE d EIS EE 5 EE DEENEN 5 UE d e EE 6 Coni ror Pales min EM MM M MEE M M M M 8 RR eseou 8 teure liget 11 Gli 12 13 Trouble SAOOUNG eege 14 Important Safeguards 1 Read all instructions 2 Disconnect the power plug before dismantling assembling or before cleaning 3 Avoid touching mobile parts of the appliance 4 Never insert fingers pencils or any other objects though the guards whenever the power plug is connected especially while running 5 appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the unit safely 6 appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervised or instruction concerni2. omega altise Water Drainage When the water tank is full the WATER FULL indicator will illuminate and the compressor will stop working A buzzer will sound Pressing any button will stop the buzzer You will need to empty the water tank before the unit will work again Before you empty the unit you will need to 1 Turn the unit off and pull the plug out of the power supply 2 Place a water tray or pan under the drainage port 3 Remove the drain knob and rubber plug on the drainage port and drain into the tray beneath 4 Once drained replace the rubber plug and drain knob into the drainage port and tighten by hand 5 Plug the unit back in and switch it on The compressor will delay restarting for three minutes and then continue to work as normal Important It is recommended that you do not move the unit around without firstly draining the internal tank If water is left in the unit then it may spill out onto the floor or carpet Continuous Drainage If you wish to operate the unit without the need to empty the water tank please HT FUE HU rer KOMA il iii ul H WW H t oft 5 n UE CR Ka 1 d P d AH m E 1 Turn the unit off and pull the plug out of the power supply 2 Remove the drain knob and rubber plug on the drainage port and retain for future use 3 Connect the drain tube supplied to the water outlet as shown and locate
3. internal water tank may become full and cause the WATER FULL indicator to trigger In this instance the compressor will shut off automatically and a buzzer will sound Pressing any button will stop the buzzer You will need to empty the water tank before the unit will work again refer to the drainage section Adding Water To utilise the full potential of the cool mode of your portable air conditioner we recommend approx 1000mls of water be added to the water injection port just prior to initial start up To add water see Figure 7 1 Take out the filter frame located at the bottom of the back of the unit 2 Use a water cup to pour water into the water tray Do not pour more than 1000ml Do not overfill the unit 3 Put back the filter frame into the unit Normally an adequate quantity of water is collected to keep the recycling process operating However in high temperatures over 30 C or dry climates adding water to commence the Aqua Chill mode will greatly assist the efficiency and operating temperature of the unit but is not critical to the functioning of the unit Please ensure that you do not over fill the unit or the water tank full indicator may be triggered Do not fill the water injection port while in fan mode Please Note Adding water is not a requirement for this unit to function normally If you choose not to add water to this unit it will not adversely affect the warranty or its regular performance
4. 20 C e Press UP or DOWN buttons or to set the desired temperature between 18 32 C As you set the temperature the display window will show the temperature you set Otherwise it will show the ambient temperature of the room Press SPEED button or to select the fan speed either low or high Timer On When the unit is switched off press TIMER button to set timer on e Press UP or DOWN buttons to adjust the time from 1hr to 24hrs e Time will vary 1hr accordingly for each press of either the UP or DOWN buttons e Atthis stage also select the mode settings that you wish the unit to turn on with When the set time is reached the unit will turn on automatically omega altise Timer Off When the unit is operating press the TIMER button to set timer off Press UP or DOWN buttons to adjust the time from 1hr to 24hrs Time will vary 1hr accordingly for each press of either the UP or DOWN buttons When the set time is reached the unit will turn off automatically NOTE Timer on and Timer off modes cannot be set to function at the same time Sleep Mode If you select the SLEEP mode while in cooling mode the set temperature will increase 1 C at the end of the 17 hour and another 1 C at the end of the second hour and then maintain that temperature until switch off or manually changed If you select the SLEEP mode while in heating mode the set temperature will decrease 1 C at the end of the 17 hour and another 1 C a
5. ent any sharp bow or bend in the exhaust e he exhaust air must flow freely otherwise the performance of the portable air conditioner may be adversely affected or the unit may malfunction e Figure and Figure 4 show correct mounting of the flexible exhaust hose Fig 3 e Figure 5 shows the incorrect mounting of the flexible exhaust hose NOTE The length of the flexible exhaust hose can be extended up to approx 150cm We suggest using the minimum length of exhaust duct for maximum performance This length has been designed according to the specifications of the air conditioner Do not use an extension or exchange with a different hose as that may lead to malfunction Fig 4 Do not use the unit in the bathroom or other humid environments Fig 5 Installation of the active carbon filter This unit comes with an active carbon filter as part of the accessories pack not pre installed To use the active carbon filter it will need to be installed as follows 1 Remove the filter frame from the unit 2 Separate the filter fixer from the filter frame 3 Remove the active carbon filter from its plastic bag Insert the active carbon filter into the filter frame Fix the filter by reassembling the fixer onto the filter frame 6 Re fit the filter frame inside the unit Control Panel omega altise Speed ventilation button Timer button Display window Receiver for remote control Heating mode indicato
6. gt O A N 10 Removable air filter Accessories 11 Flexible hose exhaust 12 Adjustable window kit 13 Window exhaust adapter 14 Remote control 15 Active carbon filter 16 Drainage tube for continuous drainage Installation omega altise Before you use this unit please ensure it has been kept upright for at least 24 hours The unit should be installed in a flat dry place Leave at least 50 space around the unit Fig 1 Thread one end of the flexible exhaust hose to the exhaust outlet adapter On the other end screw on the window exhaust adapter Window Installation The window kit has been designed to fit most standard vertical and horizontal windows However it may be necessary for you to modify some aspects of the installation procedures for certain types of windows Open the window and insert the window kit to cover the open gap Next slide the window across so that the kit is held securely You may need to adjust the size of the window kit and secure it with screws This technique may also be used for sash windows Once the window kit is in place simply snap the window exhaust adapter into the hole provided on the window kit You are now ready to use your portable air conditioner Note Take care to secure your window against intruders Fig 2 omega altise Mounting of the flexible exhaust hose e The bend of the exhaust pipe is very important e care to prev
7. n a rubber or carpeted base The unit is noisy The unit is on a tiled surface Turn the unit off wait 3 minutes until the temperature has decreased then turn the unit on again The exhaust tube is attached Set the exhaust tube correctly as The unit starts and incorrectly or is bent indicated in the installation section stops frequently You have added an extra flexible Banaue hecada des exhaust hose Distance is too great The compressor does The overheat protection may be not work activated Make sure the remote control is The remote control Remote control signal not correctly aimed at the control panel does not function detected by the control panel The batteries are drained Replace the batteries Turn the unit off call your Customer Error code appears The LED is flashing E1 or E2 Care Line on 1300 739 033 CAUTION Switch off the unit and unplug it immediately if anything abnormal occurs Then contact the omega altise Customer Care Line on 1300 739 033 gt WARNING Do not attempt to repair the unit yourself Doing so could void the warranty and cause damage or personal injury gt Omega Altise products are distributed in Australia by MEA A Division of Hagemeyer Brands Australia Pty Ltd ABN 28 001 375 686 Locked Bag 4013 Kingsgrove NSW 2208 Phone 1300 739 033 Fax 1800 838 899 Email customerservice meaappliances com au Web meaappliances com au 14
8. ng use of the appliance by a responsible person for their safely Do not use the appliance for any other purpose than its intended use The appliance must not be used if the guards are not fastened according to instructions When the power cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard 10 Do not use your appliance with an extension cord unless it has been checked and tested by a qualified electrician or electrical supplier 11 Return to MEA or authorised service agent 12 The air conditioning unit must always be stored and transported upright otherwise you may cause irreparable damage to the compressor in case of doubt we suggest to wait for at least 24 hours before you start the air conditioning unit 13 Avoid restarting the air conditioning unit unless 4 minutes have passed since being turned off or the compressor may get damaged 14 Never use the mains plug as a switch to start and turn off the air conditioning unit Use the provided ON OFF switch located on the control panel 15 Always place the portable air conditioner on a dry stable surface omega altise Introduction Thank you for choosing an omega altise portable air conditioner This manual contains information regulations and warnings which are of fundamental importance if the appliance is to be installed correctly and the highest performance in the safest possible condition
9. ose mode Press SPEED button to select the fan speed either low or high he temperature cannot be set Cool Mode The cooling mode uses a refrigerated circuit compressor to cool the room by transferring the heat from the inside to the outside through the air exhaust hose and cooling the air that it returns to the room Press MODE button to choose COOL mode e In COOL mode the temperature of this unit is pre set to 24 C e Press UP or DOWN buttons or to set the desired temperature between 18 32 C As you set the temperature the display window will show the temperature you set Otherwise it will show the ambient temperature of the room Press SPEED button or to select the fan speed either low or high In COOL mode the unit will use Aqua Chill technology to improve the cooling efficiency of the unit See the Aqua Chill section for further details Please Note The temperature adjustment setting is not a direct correlation to the ambient room temperature For example adjusting the setting to 18 C will not necessarily bring the ambient room temperature down to 18 C Heat Mode APC12RC only The heating mode uses a reversed refrigerated circuit compressor to warm the room by transferring the cold from the inside to the outside through the air exhaust hose and warming the air that it returns to the room Press MODE button to choose HEAT mode e In HEAT mode the temperature of this unit is pre set to
10. r APC12RC only Mode button Automatic mode indicator Cooling mode indicator Fan mode indicator UP button DOWN button zl e ree ees lup O Operating Instructions On Off 12 13 14 15 16 17 18 19 20 21 22 Press ON OFF button the unit will start in AUTO mode To turn the unit off press ON OFF button again Power on indicator Water full indicator ON OFF power button Sleep mode button TiO2 UV ionizer button optional Compressor operation indicator TiO2 UV ionizer indicator optional Sleep mode indicator Timer mode indicator Low fan speed indicator High fan speed indicator e Please note The display window will show the ambient room temperature from 0 C to 50 C except during setting on the timer on or timer off function Auto Mode AUTO mode selects the mode either fan or cooling that is suitable to the temperature of the room e The unit will automatically start in AUTO mode or you can press MODE button to choose Auto mode e Ifthe ambient temperature is o Higher than 23 C the unit will work in cooling mode o Higher than 20 C but below or equal to 23 C the unit will work in fan mode e AUTO mode will choose the ventilation speed automatically 8 omega altise Fan Mode The Fan or ventilation mode moves the air allowing for the recycling of air much like a general fan Press MODE button to cho
11. rs 3 End of Season Pull out the plug from the drain outlet and remove any water from the internal bottom water tank You can remove the water entirely by slanting the unit backwards Run the unit in Fan mode for several hours to ensure the inside of the unit is dry owitch off the unit and disconnect the plug from the power supply Remove the flexible exhaust duct and adapters and keep stored in a safe dry place Take the batteries out of the remote control and keep in a dry place Wrap the unit with the plastic bag and keep it in a dry place omega altise Trouble Shooting Before contacting a professional please read the following troubleshooting guide Check the unit is plugged in properly power SURRY turn the power on and turn the unit on The unit does not work The water full indicator is Turn the power off drain the water tank flashing and restart the unit Timer function is active Cancel timer function In direct sunlight Draw the curtains Windows doors open many Close windows doors remove the heat people or a heat source in the room to perform Dirty filter Clean the air filter s source if possible The unit does not seem Air inlet or air outlet is blocked Remove any blockage Ambient room temperature is DEE E E Change your temperature selection The unit is not on a hard or flat Place the unit on an even solid surface surface less vibrations Mount the unit o
12. s is to be obtained We suggest that you read the manual carefully before installing or starting up the unit This portable air conditioning unit is of the mono tube type is conveniently transportable on wheels with an air operating system for domestic use This unit has the following settings for ease of use e Ventilate fan e Cool and e Heat APC12RC only The ventilation mode moves the air allowing for the recycling of air much like a general fan The cooling mode uses a refrigerated circuit compressor to cool the room by transferring the heat from the inside to the outside through the air exhaust hose and cooling the air that it returns to the room The heating mode uses a reversed refrigerated circuit compressor to warm the room by transferring the cold from the inside to the outside through the air exhaust hose and warming the air that it returns to the room Features of your new Portable Air Conditioner Nocostly installation required e Easily moved with castors and handle e Electronic control panel Hemote control Low noise and strong breeze e On off timer function e hree minute restart delay to protect compressor Energy Saving Tips 1 Do not cover or restrict the airflow from the outlet or inlet grilles 2 minimum distance from furniture and walls should be 50cm 3 Keep blinds and or draperies on any windows closed during the sunniest part of the day 4 Keep the filter
13. s clean Under normal conditions the filters should be cleaned approximately every 2 weeks please see the maintenance section for further instructions Since the filters remove airborne particles more frequent cleaning maybe necessary depending on the indoor air quality and if you have pets inside the home 5 Setthe fan speed switch to high cool and the thermostat to the coolest position for the initial start up then set the Fan switch to Low cool and lower the thermostat to a comfortable setting 6 Ensure all windows and doors to the room you are operating the unit in are closed omega altise SSC LEE Heating ug mens 20 1 9 Dimension wxdxh mm 365 x395 45 365 x395 x745 365 x395 x745 Net weight kg 29 29 30 Lower Storage Tank Capacity 1500ml 1500ml 1500ml NB The above specifications are correct at time of printing However due to our policy of development and improvement we reserve the right to modify technical data without prior notice ga altise ome Parts List Front 1 2 Air outlet grille Control panel 3 Carrying handle 4 4 Castors Back 5 Removable air filter 6 Air inlet grille WI L bg Ze m wi E LITT mm i meet 8 Exhaust outlet adapter 9 Water drainage port E O c fa O 2 E 42 gt 4 42 O _ 0 TO O O
14. t the end of the second hour and then maintain that temperature until switch off or manually changed In SLEEP mode the fan speed will remain at low Cancel SLEEP mode by pressing the SLEEP button again The unit will turn off automatically after the SLEEP function has been running for 12 hours SLEEP mode is not available while in FAN mode Time will vary 1hr accordingly for each press of either the UP or DOWN buttons When the set time is reached the unit will turn off automatically Airflow Regulation The airflow can be manually adjusted via the roller situated at the front of the air vent Remote Control All the above functions can also be performed with the supplied remote control This remote control requires one button cell No CR2025 to operate omega altise Aqua Chill Technology When operating in Cool Mode this unit uses a self evaporative system that extracts water from humid environments and collects it in an internal water tank Once sufficient water is collected it is recycled over the condenser assisting to cool the condenser and internal refrigerant gas faster than only air Cooler condenser and refrigerant means improved cooling efficiency and performance of the unit Some of the water recycled over the compressor is evaporated and expelled from the machine as water vapour through the flexible exhaust hose During very humid conditions the collection of water may be in excess of the evaporation rate and the
15. the other end into a drain 4 The drain tube may be extended by using a suitable connector and an extension tube OD 18mm Extended drain tube OD 16mm 5 Plug the unit back in and switch it on The compressor will delay restarting for three minutes and then continue to work as normal Fig 9 Please note 1 The drain must be at or below the outlet level 2 Flashing comp water full indicator will not function in this mode of drainage 3 When the room humidity is over 8596 it may be necessary to utilise the continuous drainage method omega altise Maintenance Cleaning Turn off the unit and pull the plug out of the socket before cleaning 1 Clean the surface Clean the surface of the unit with a duster or a damp soft cloth Do not use chemical solvent like benzene alcohol gasoline and etc or the surface may be damaged 2 Clean the air filter The air filter should be cleaned every two weeks If the air filter is blocked with dust the efficiency of the unit will be reduced To clean the air filters 1 QI e 49 Pull out the air filters as shown in Figure 11 Wash the air filter by immersing it gently in warm water under 40 C or 104 F with neutral detergent Rinse the filter and dry it in a shaded place Push the air filter back into the original position Alternatively suction the filters using a vacuum cleaner with the dusting brush attachment to remove any build up of dust or debris on the filte
Download Pdf Manuals
Related Search