PL9000 – Power Pop Universal Keyless Entry
Contents
1. amp PL9000 Power Pop Universal Keyless Entry System Tonneau Cover Installation Instructions 1 Replace both of the existing rotary latches on the tonneau cover with the new supplied power adaptable rotaries Install both Actuator Brackets with the supplied Bracket Bolts Install both Linkage Rods by sliding them into the grooves in the rotary latch cable clamps then hook the end of the linkage rods through the holes in the end of the Actuators and bolt the Actuators to the Actuator Brackets with the supplied Actuator Screws there is a tab on the Actuator Bracket that only allows the Actuator to be mounted on one way You may also need to install new strikes which are also supplied i Actuator Bracket i Actuator Power Adaptable Rotaries Truck Harness N Pa Button Harness S Tonneau Harness a N A Reciever Strikes Key FOBS Rotary Latches ai p z A Actuator Screws Bracket Bolts Vi _ Linkage Rods a AE lt A Receiver Harness Actuator ee Brackets Cable Ties Linkage Rod 2 Mount Keyless Receiver to tonneau cover centered between the rotary latches Be sure to use proper length screws and only screw into the thick portions of the tonneau as to not protrude the outer surface of the tonneau cover onneau Harness Optional LED light oon U ee ee lt n Rotary Latch 3 Connect receiver actuator outputs to the actuators and bundle u2. ARRANTY FORM Please complete and mail this form to record your warranty with the manufacturer NAME POP amp LOCK MODEL ADDRESS VEHICLE YEAR CITY _ VEHICLE MAKE MODEL STATE ZIP REASON FOR RETURN continue on other side TELEPHONE EMAIL ADDRESS
3. Driver Side Kick Panel Note 3 amp 9 Black Yellow Tundra Crew Max i f f Tundra Double cab Blue Red Blue Black Diver Side Kick Panel Note 5 amp 9 See Notes following page LOADGNDLOCK VEHICLE WIRING CHART Pop N Lock Load N Lock All wire color information is for reference only and may vary by vehicle Please verify with a test light If you have trouble locating the lock and unlock wires test all the wires with a test light that are inside the rubber boot that runs between the door and the cab of the truck to find correct wire colors To Test With a Test Light Ground the test light to good conducting ground and probe the wire to be tested by piercing the wire case to connect to the copper wire inside Hit the lock button to see if the test light lights up If so this is the lock wire Do the same with the unlock wire to verify the correct wire Note 1 If the wiring is connected in the driver s side kick panel the Handle will lock unlock with the driver s door If you prefer the Handle to lock unlock with the passenger door on some models the wiring may be connected into the passenger side kick panel using the same color wiring If the same colors can t be found use a test light to find the passenger side colors Note 2 On the CHEV Y GMC 03 Two door or Extended Cab Models if not using a relay harness it is necessary to remove the driver s side door panel and attach the lock and unlock wires dire
4. ctly to the wires of the door lock actuator inside the door Once the door panel is removed you will need to remove the driver s side kick panel and fish the harness wires through the rubber boot that runs between the door and the cab of the truck and into the door Use the supplied Wire Taps to attach to the specified wires directly under the truck s door lock switch and test the locks If the truck locks operate opposite the lid lock reverse the leads connected Note 3 Some 04 Toyota Tundra models used blue white instead of pink black for the lock wire and black yellow instead of red orange for the unlock wire Note 4 Make sure the key is out of the ignition when testing this model as the doors will automatically unlock when trying to lock Note 3 If you have trouble locating the lock and unlock wires test all the wires that are inside the rubber boot that runs between the door and the cab of the truck Once you locate them you can follow them to a location that makes tapping to the wires easier This works on most models except 03 G M Note 6 On the Honda Ridgeline the lock and unlock wires are located in the fuse panel down by the driver s side kick panel The yellow black lock and the yellow green unlock wires are in the small green plug that is located at the bottom front side of the fuse box A small hole may need to be drilled in the side of the bed rail near the top rear on the driver s side of the bed to access the rea
5. e hood Connect the red wire from the Truck Harness to any constant 12 volt power supply most trucks have an auxiliary power terminal for such accessories Be sure to properly ground the black wire Button Harness 7 If using the in cab remote button option route the Button Harness into the cab of the truck through an existing grommet Drill a 2 hole in the desired location of the button and mount it through the hole Attach the black wire to a good ground and plug the gray wire from the Button Harness into the gray wire on the Truck Harness ACTS UGC User Guide 1 input for system disable 2 Ap is input to active program The system would pause to work if triggered 8 times continuously in 30s and start to work again 30s later 3 Ap2 is the new added input to activate program which can be controlled by transmitter Press the button of Unlock Ap2 begins to work Press the button of Lock Off Ap2 stops 4 The active and negative startup of Ap and Ap2 can be switched by JS1 and Js2 5 Press button of Unlock the central door locking system and Ap2 would begin to works and the flash lights would be on for 2 minutes 6 Press the button of Lock Off Ap2 stops and flash lights turn off 7 Press the button of Light the flash lights would be on for 5 minutes ACCESS UG UC User Guide 8 Code learning Press the programming button for 3 times LED lights would be on If t
6. here is no transmitter to be learned the LED will turn off and quit the learning mode After learning the first transmitter the lights would be on and would turn off and quit the learning mode if not learning in 10 seconds After learning the second transmitter the lights would be on and would turn off and quit the learning mode if not learning in 10 seconds After learning the third transmitter the lights would turn off 9 Press the button of Unlock for 8 times within 30 seconds the system would pause to work and start again in 30 seconds it s the same if press the button of Lock Off and Light alternatively for 8 times within 30 seconds 10 the function of transmitter is as follow E POWERED BY LOC SCV LGM ESCH User Guide Wiring Diagram Progran button Antenna Program LED New increase input to activate program amp select nut to activate program amp select aC Input to activate program AP1 ES New increase Input to activate program AP2 E Light input Acuator 1 output POP amp LOCK LLC www popandlock net 800 342 5911 Pop N Lock Load N Lock All wire color information is for reference only and may vary by vehicle Please verify with a test light If you have trouble locating the lock and unlock wires test all the wires with a test light that are inside the rubber boot that runs between the door and the cab of the truck
7. new used or refurbished and as such Pop amp Lock LLC and Pop amp Lock Corporation is unable to warranty such purchases Pop amp Lock LLC advises using extreme caution when buying through auction sites as you ll be doing so at your own risk 3 No Liability Pop amp Lock Corporation is not liable for any loss or damage claimed by Customer or any third person to have been suffered or incurred as a result or or related to the Locks purchased under this Agreement regardless of the circumstances or form of action except any bodily injury or death for which Pop amp Lock is liable under products liability law Without limiting the generality of the foregoing in no event will Pop amp Lock LLC be liable to Customer for any indirect special or consequential damages regardless of the circumstances or the cause of action particularly not for the value of a vehicle or any other money damages in the event that a tailgate is stolen either notwithstanding the use of a Pop amp Lock or when it has been returned for repair or replacement END OF TERMS AND CONDITIONS Please Mail Completed Warranty Form below In Self Addressed Envelope To POP amp LOCK LLC 1271 CONTRACT DRIVE GREEN BAY WI USA 54304 Additional Install Instructions and answers to technical questions can be found on our website at www popnlock net or by calling Technical Support 1 800 342 5911 Q Monday Friday 8am to 5pm CST POP amp LOCK LIMITED W
8. p and wire tie any excess wire length Cee S Tapa gags 5 ee Coles aa ae a Da yae Melie Se Ae s ed 4 Connect Tonneau Harness to the Receiver If in h 1 n lin HAA f MA X h A V 2 using the optional in cab cS PRS eR I OPO AARS a remote button connect the gray wire from the Tonneau Harness to the gray wire on the Receiver Route the Tonneau harness 1 Gate es wire up the center of the DE S ROS aie Pes ite Wes loot Gok oe tonneau cover then over to Rt al BE SAE TA Ge ne the driver side front corner n SSNV A T of the box Mount the harness with supplied Cable Clamps and pi PbO Ss screws or under the a sa Receiver Connection by carpeted head liner Leave in RER Ee EN B the end of the harness AEA O accessible to be able to l later connect it to the Truck Harness POWERED BY MOAD lt Ye LOCK 5 Connect the optional 12 volt LED light 01355 to the timed light outputs on the Receiver black to black and white to white Mount light where desired Pi Timed Light output also A controled with Key FOB f 6 Attach the Truck Harness to the Tonneau Harness with the one way plug in the front corner of the tonneau Route the Truck Harness down along the truck frame and up into the engine compartment Fasten the Truck Harness securely with wire ties along the frame Bundle and wire tie any extra wire from the Truck Harness securely up under th
9. r tail light compartment to attach the brake light and power lock wiring Note 7 On the 07 Double Cab Tacoma the lock wire is located in the 10 pin plug pin 9 Blue Black wire The unlock wire is located in the 12 pin plug pin 10 Blue Red wire both plugs are hanging loose in the driver side kick panel Note 8 On the Ford 09 crew cabs the lock unlock wires are located under the drivers side sill plate the plate you step on when getting in and out of the truck The wires run from the driver s side front door to the driver s side rear door Gray Brown for Lock and Purple Gray for unlock there are multiple and different size purple gray wires use the largest gauge Note 9 On some models the factory keyless system may be programmed to re lock the truck doors after 1 or 5 minutes if the truck is unlocked and the door are not physically opened Please refer to the user s manual or contact your local dealer if you require a change to the factory programming Please visit www PopandLock net for the latest wiring Info For Technical Support Monday Friday 8 00 am to 5 00 pm CST 1 800 342 5911 LOAD GIDLOCK LIMITED WARRANTY TERMS AND CONDITIONS 1 Installation Pop amp Lock LLC and Pop amp Lock Corporation is not responsible for installing the Pop amp Lock or for the harm suffered by any person as a result installing it 2 Warranties a Customer acknowledges that it is unreasonable to belie
10. to find correct wire colors MAKE MODEL YEARS omy Driver as Kick Panel Chevy GMC Silverado Sierra 99 02 Gray Just Below Sues Side Fuse Block Silverado Sierra Chevy GMC S 10 Sonoma 03 06 Gray Driver Side Door Between Switch and Lock Actuator Note 2 Colorado Canyon Silverado Sierra Chevy GMC S 10 Sonoma Blue Driver Side Door Between Switch and Lock Actuator Note 2 Colorado Canyon Chevy GMC See eta Under the sill plate in the wiring harness that goes under the driver s Crew Cab lU Aonoma ray side seat Colorado Canyon e e E EA E E EA Doe OrangerBlack Be Driver Side Kick Panel Note 5 Driver Side Kick Panel Dodge Dakota Lt Green Blue Purple Black Or Passenger Side Kick Panel Note 5 Sots Ram 1500 94 03 Stink O Driver Side Kick Panel Note 5 Ram 1500 2500 Brown Orange or IN Ram 1500 2500 Orange Gray or Lime Green or SN Ram 2500 3500 94 03 Orange Black Pink Violet Driver Side Kick Panel Note 5 Ridgeline o Yellow black Yellow green Driver s Side Kick Panel Note 6 amp 9 l Brown or Green Red or i z Toyota Tago MaRe gilar edb 98 06 Blue Blue White Driver Side Kick Panel Note 4 amp 9 Access cab Tacoma Double cab 98 06 Blue Pink Driver Side Kick Panel Note 4 amp 9 Toyota eee ae 07 Blue Black Blue Red Driver Side Kick Panel Note 7 amp 9 Access Cab 99 03 Pink Black Red Orange Driver Side Kick Panel Note 5 amp 9 Toyota Tundra 04 Pink Black or Blue White Red Oranecior
11. ve that any device whatever will prevent a theft in the case of every attempt and that the most that can be expected from a so called anti theft or security device is that it will deter many thieves b POP amp LOCK LLC and Pop amp Lock Corporation MAKES AND CUSTOMER RECEIVES NO WARRANTY EXPRESSED OR IMPLIED EXCEPT THE WARRANTIES OF TITLE TO THE POP amp LOCK AND THEIR MERCHANTABILITY PARTICULARILY NO WARRANTY OF FITNESS FOR A PARTICULAR USE OR PURPOSE OR AGAINST INFRINGEMENT c As Customer s only remedy Pop amp Lock LLC and Pop amp Lock Corporation will repair or replace at its option and without charge any lock that is defective in material or workmanship when received by Customer and is returned to Pop amp Lock LLC and Pop amp Lock Corporation FOB Pop amp Lock Corporation s offices within one 1 year after it s receipt by the Customer Pop amp Lock LLC will ship all replacement or repaired Locks to Customer FOB Pop amp Lock s shipping point d Factory support is only available for Pop amp Lock products purchased as new through an Authorized Pop amp Lock dealer Please Note Pop amp Lock Products purchased on auction sites such as Ebay Amazon and Craigslist to name a few will not be covered under factory warranty under any circumstance Pop amp Lock LLC and Pop amp Lock Corporation is unable to verify whether products sold through Auction Sites are
Download Pdf Manuals
Related Search