KISSRX_Manual.101007..
Contents
1. Mhi AILSS RO www watchguardalarms com au Proudly Designed in Australia Narrow Band Wireless Receiver with 2 x Code Hopping Remote Controls For Most Alarm Control Panels F Current_Instructions Standard Home Alarm kissrx doc N517 Instruction Manual Contents Description Page Product Description amp Features Remote Control Function Master Default Setting Programming Remote Controls Programming Wireless Detectors Wireless Detector Supervision Wireless Detector Low Battery amp Tamper Warning Memory Recall Function NINIOIOI AOIN Your KISS RX is a state of the art narrow band wireless receiver designed to operate with most alarm control panels Product Description Main Features include Simple Installation Code Hopping Remote Control Technology remotes can not be copied by scanning or code grabbing Remote Functions include Arm Disarm amp Panic Ability to quickly add or erase detectors from your system 4 Wireless Detector Zones Available Wireless Detector Supervision Output Low Battery Warning Output Intelligent 1 trigger only until batteries replaced Detector Tamper Warning Output Intelligent Detector Learning Program to prevent accidental code duplication Memory Recall Function to identify individual detectors sending low battery or tamper codes Wireless Detectors available include PIR s Internal or External Reed Switches Smoke Sensors amp2. Carry out the default procedure outlined below You can default your K SS RX in case you make a mistake or are unsure of your receiver setup Defaulting your receiver will cause all detector 8 remote codes to be erased To default your receiver follow these steps 1 Set all dipswitches on Bank 1 to ON m ARPS 4 2 8 4 5 6 7 8 OFF Bank 1 2 Press amp Hold the delete button for 5 seconds a gt 5 seconds press Delete 3 All LED s on the receiver will flash once together to confirm that the receiver has been defaulted 4 Return all dip switches back to the OFF position IF YOU ENCOUNTER ANY PROBLEMS WITH YOUR KISS RX OR REQUIRE ADDITIONAL TECHNICAL INFORMATION NOT CONTAINED IN THIS MANUAL PLEASE CONTACT YOUR RHINO DEALER Programming Remote Controls TO ADD A REMOTE CONTROL 1 On Bank 1 set dipswitch Number 8 only to ON The yellow Program LED will come on If theLED flashes check that you don t have more than one dipswitch set to on ON NOTE WHEN 7 a a w E sl in KA ii PROGRAMMING REMOTES amp WIRELESS DETECTORS Bank 1 Due to the excellent 2 Press amp Hold button 1 on your remote performance of the receiver you are likely to Swamp the receiver with too much RF jE signal if you transmit within 5 metres of the receiver To prevent this from occurring simply remove the antenna from your receiver whilst 3 Press the Add Button The red Valid LED will start flashing at 0 5HA Program
3. Wireless Emergency Pendants Remote Control Functions ARM DISARM Pressing button one once As soon as you release the alarm will respond PANIC Activate by pressing amp holding down button 1 for 3 seconds This sets off the siren To cancel panic press button one once NOTE Button 2 not used Panel Connection Diagram Receive On when any data packets are received even if codes are not programmed Valid On while valid data is decoded e g while Tx is pressed or PIR transmitting Flashes 6 times when in program mode and valid data is received for storage Program On when any switch is in the on position flashes when more than one switch is in the on position Run Normally flashing at 0 5 Hz indicates microprocessor is running e e e Antenna Wire Add Delete User Code 12VDC Ground Zone 1 Detector Output Keep the antenna vertical amp Zone 2 Detector Output straight and away from Zone 3 Detector Output metal Mount the receiver Zone 4 Detector Output inside the top of your panel box with the maximum possible length of antenna extending from the top Supervision Output Low Battery Output Panic Output On Off Output All outputs are open collector This means the outputs will be open circuit normally and will output ground earth for 1 second when triggered Master Default Setting After connecting your KISS RX to your panel as per the connection diagram on page 2
4. f e y Delete 4 Supervision Reporting has now been de activated for all zones 5 Return all dip switches back to the OFF position The yellow program LED will turn off amp the green run LED will begin to flash at 0 5Hz Low Battery amp Tamper Warming Your detectors will automatically transmit a low battery report to your KISS RX receiver when the batteries are nearly flat The low battery report code is also transmitted after the alarm code every time a detector is triggered After the individual detector has sent five low battery codes in a row the KISS RX will activate the low battery output once it will switch low for 1 second to tell your panel that a detector has a nearly flat battery The service person can then determine which sensor has the nearly flat battery via the memory recall function described below Please note Your K SS RX identifies a different low battery code for each individual detector When you replace the batteries your receiver will automatically see that the low battery code is no longer being sent from that detector The receiver will then reset that zone ready to activate the low battery output only if five low battery codes are sent in a row again The tamper output will switch low for 1 second whenever the front case is removed and the tamper switch is released on a Wireless PIR Detector or Wireless Reed Switch Memory Recall Function Your KISS RX has the ability to indicate indiv
5. idually which zone s are reporting either a low battery supervision or tamper report to your panel You will require a Keypad to be connected to your panel 1 Make sure your alarm is disarmed amp all dipswitches are in the off position AE 2 Select the report you require a For Low Battery press the Add button or OR Add b For Supervision press the Delete button to see if there are any detectors that have not transmitted for a period of 24hours or DS Delete C For Tamper press the User Code button e gt User Code 3 The zones that are sending the respective signal to your receiver will be illuminated on your alarm panel keypad for only 20 seconds The memory is then automatically erased so make sure you make careful note of the zones as you will not get a second chance e Watchguard re www watchguardalarms com au
6. l erase the original detector s code amp replace it with the new detector s code Furthermore if that detector code has previously been learnt into another zone the receiver will determine this as being an error and will automatically delete the code duplication by erasing the code from the other zone 2 Press the Add Button The red Valid LED will start flashing at 0 5Hz Sle kolin 3 Now trigger the sensor The valid light will stop flashing once the detector has been successfully programmed 4 Return all dip switches back to the OFF position The yellow program light will turn off TO DELETE A DETECTOR 1 On Bank 1 select the Zone 1 4 that you wish to delete a sensor from The yellow Program LED will come on If the LED flashes check that you don t have more than one dipswitch set to on m m m m m m m m 4 E g deleting a detector from Zone 1 2 3 4 5 6 7 8 OFF Bank 1 2 Press the Delete Button e lt Delete 3 The detector will now have been erased from the receiver s memory You can test this by triggering the detector and watching that the Valid LED no longer illuminates on your receiver when the detector transmits and also by watching that the Zone LED no longer illuminates on your RHINO Keypad 4 Return all dip switches back to the OFF position The yellow program light will turn off Wireless Detector Supervision All of your individual wireless detectors i e Wireless PIR Wireless Reed or Wire
7. less Smoke Detectors can send a supervision report to your receiver to confirm that they are fully functional If supervision mode is enabled the receiver will be expecting to receive the individual supervision code from each detector approximately every 2 4 hours i e at least 10 reports per day per detector The KISS RX only requires one report from each detector during the 24 hour period to satisfy the supervision criteria An extra 9 reports are still given to ensure that the supervision report is received If all 10 Supervision reports are missed from one detector during the 24 hour time frame then the supervision output will be activated it will switch low for 2 seconds TURNING SUPERVISION ON OR OFF Default setting is OFF To turn on supervision 1 Disconnect power from the receiver 2 On Bank 1 set dip switches 1 amp 8 to ON Kumun Bank 1 3 Reconnect power The yellow program LED will begin to flash at 0 5Hz Within 60 seconds press the Add Button The green run light will turn on OE 4 Supervision Reporting has now been activated for all zones 5 Return all dip switches back to the OFF position The yellow program LED will turn off To turn off supervision 1 Disconnect power from the receiver 2 On Bank 1 set dip switches 1 8 8 to ON Puan Bank 1 3 Reconnect power The yellow program LED will begin to flash at 0 5Hz Within 60 seconds press the Delete Button The green run LED will turn of
8. ming You will now have to be within approx 1m of the receiver whilst OFS ME ME e programming Add 4 Nowrelease button 1 on the remote The red valid light will turn off Y 5 Repeat steps 2 4 for any extra remotes that you wish to add Maximum of 5 can be used 6 Return dipswitch 8 to the OFF position The yellow program light will turn off TO DELETE ALL REMOTE CONTROLS 1 On Bank 1 set dipswitch Number 8 to ON The yellow Program LED will come on If the LED flashes check that you don t have more than one dipswitch set to on TE E C1 IMPORTANT When programming make sure that no detectors are 2 Press the Delete Button transmitting as they will interfere with your e programming Delete procedure 3 All remote controls will now have been erased from the memory of the receiver 4 Return dipswitch 8 to the OFF position The yellow Program light will turn off Programming Wireless Detectors Wireless PIR Wireless Reed Switch Wireless Smoke Sensor or Wireless Emergency Button TO ADD A DETECTOR 1 On Bank 1 select the Zone 1 4 that you wish to program a detector into The yellow Program LED will come on If the LED flashes check that you don t have more than one dipswitch set to on E m m m m m m m 4 E g programming a detector into Zone 1 075 1 2 3 4 5 6 7 8 OFF Bank 1 Note Learning a new detector into a zone which already had a detector learnt into that zone wil
Download Pdf Manuals
Related Search
KISSRX_Manual.101007..