Sinewave inverter - Sinus Wechselrichter -
Contents
1. Use After connecting the inverter make sure the user devices are correctly plugged in and that there is no possible contact between the Line OUT 6 and a person The working device generates high tensions which could be fatal The inverter can be activated by moving the switch to the Auto position The on indicator green LED 3 is illuminated SI xxxx model If no user device is connected the LED blinks after some seconds which indicates that the standby mode has started If a user device is plugged in the green LED remains illuminated indicating the uninterrupted presence of 230V in the outlet If you wish to deactivate the standby mode put the switch in Lock position The inverter will be then working continuously SI xxxxTP model Twinpower option The green LED remains illuminated indicating the uninterrupted presence of 230V in the outlet The Lock function deactivates the economical mode Warning With the lock mode the load consumption of the inverter is 15 to 20 times greater Remote control The inverter can be controlled remotely with a switch bi stable connected to the Faston 5 connector on the under side of the device The main switch 4 has priority over the working mode of the device If the remote switch is close the inverter is out of use STUDER INNOTEC Adjustments Not automatic with Twinpower version2. 8XX Standby level adjustment Not available with Twinpower option Fault indicator red LED Remote control d Run indicator Green LED Main switch Remote control connector Output 230 VadCaution High voltage C9 9 9 9 Plus battery Line out 230 Vac Minus battery 9 Solar panel connector 2 5mm2 0 Braun Indicator Battery charging Yellow 5 Yellow greenL 11 Indicator battery full charged Green E Bue N 02 Alarm contact 60V 0 5A potential free Battery connection Check battery polarity Max cables lenth 2 m Battery size sould be ajusted to the inverter s power Cbatt Ah 5 x Pnom Unom This value could be divided by tree for short time applications User manual SI V3 2 1 E 7 STUDER INNOTEC SI Wiring diagram for SI 600 800 S Solar charge regulator Max 16A total Caution High voltage 230V Avoid contact i User manual SI V3 2 1 E STUDER INNOTEC Option SI performance 3 phased Three SI inverters can be connected together to build a 3 phased grid They have to be equipped with the PE option Working Two ways of working are possible with the SI performance 1 Working alone One SI inverter can be used alone The inverter works then as a single one like it is described in this manual 2 Working in a grid Thanks to the connecting cable three inverters can be connected together in order to obtain
3. Outside these ranges the inverter is automatically disconnected User manual SI V3 2 1 E SI These values correspond to a no load situation and they are automatically adjusted according to the current of the battery The internal temperature and the maximum power are also submitted to control In the case of prolonged overload or deficient ventilation it is not possible to restart the inverter until it has cooled down Indicators Green Run LED 3 Illuminated the inverter is connected A 230 V tension is present in the outlet Blinking only SI version The inverter is in Autom mode and no voltage is detected by the standby system A 230 V tension is intermittently present Red Fault LED 2 The inverter is stopped The tension of the battery is not correct After an overload overheating or short circuit To restart the inverter after a failure put the switch 4 in OFF position for 10 seconds then connect again Safety The inverter is internally protected against overloads and short circuits Should this protection fail the inverter is equipped with a fuse fire protection If the fuse is broken qualified technicians should control the installation and change the fuse Internal fuse Fuse Inverter SI mod 40A 648 50A 624 1248 60A 824 1448 80A 612 2348 2360 100A 812 1224 3548 3060 2 100A 1212 1624 2324 2 125A 3324
4. eU aee 6 SOLAR CHARGE CONTROLLBB 6 LED Charging IT 3 gei a diei ee Mg esci oben 6 LED Bat 10096 10 i RR ene eR EE REI T RED EUN RUINA 6 MAINTENANCE Bisisisscccsessscessssescossosssoossetnssosecsaacessetesssdectasesssededestecsssensecsesesdesssonsisssuvessosssscassotescesestsdenss 6 LEGISLATION e 6 LIMITATION OF LIABILITY 6 CE DECLARATION OF CONFORMITY cssssccssssscccssssecccssscccssssccccssssccesssccsssssscccessnsccscsssecceses 6 DESCRIPTION AND WIRING DIAGRAM ee eee eese enne eee tone etta eee seen aee teen eee esee eee en aee S 7 WIRING DIAGRAM FOR SI 600 800 S SOLAR CHARGE REGULATOR 8 OPTION SI PERFORMANCE 3 PHASED eee eese eere eese eee seen Pee seen eee seen ae eeS 9 Ado d Sn cmNUR E 9 GONG secre estet RE rt e rete npe nee 9 2 Working ina STI ss ue etch t Rt te ree ed te ete ther 9 CONNECTING Pm 9 COMMISSIONINQG dt eee testet eere et eet eee 9 TECHNICAL DATA iocos erecto se Spr aco eva dU ae eva Ye irodada eiA 10 OPTIONS eae aaa aa eas aaa a aL Ra ae Sen OUI UU 10 User manual SI V3 2 1 E SI STUDER INNOTEC Introduction The SI sine wave inverters have been designed to meet indus
5. he use of higher fuse value will not improve the performance of the inverter and will degrade Safety protection STUDER INNOTEC Options Alarm contact A contact with no potential 0 5A 60V is available 12 It warns the user alarm or control system when the inverter has been stopped due to a failure or is out of use It is closed when the inverter is working Solar charge controller This controller has been designed to charge the batteries with solar installation only The maximum no load tension of the solar installation should be of 23V for the 12V applications and of 46V for the 24V applications The max DC current is 16A and should never be exceeded 20A 1min The mode of adjustment is of the I U floating type and assures optimal charging conditions for the life Shine Charging diagram 14 4V 28 8V SI Maintenance The SI inverters do not need any special maintenance The casing may be cleaned with a damp cloth not wet In the case of malfunction the inverter should be sent to the salesperson for control Legislation In all cases the assembly and installation must be done by qualified technicians observing the national requirements and rules stipulated You will find complete information about this in the relevant institutions Limitation of liability STUDER INNOTEC SA cannot control the installation use and maintenance of the inverter Thus we are not resp
6. Standby Level 1 The activation of the inverter when working in automatic mode is dictated by the detection of a load With this function it is possible to adjust the minimum load detected between 0 3 and 20 Watts This level is factory adjusted to 2 watts and so no further adjustment will probably be needed Adjustment procedure Make sure that no device is connected Check for the presence of hidden users such as television fax video which often have a standby mode and remain working even after being turned off Put the switch in Autom position Introduce a screw driver N 1 delicately in the hole 1 provided and turn gently until you feel the screw driver insert in the groove of the screw Turn clockwise Y until tight without pressing do not force Wait until the green LED blinks Activate the minimum charge you wish to detect Turn the screw slowly anti clockwise Vv without pressing until the inverter activates green LED illuminated Check that the inverter goes back to standby mode a couple of seconds after deactivation of all charges Warning In maximum anti clockwise position the inverter continues to work even if there is no load Control The tension of the batteries is submitted to control During their use the tension must be between the following ranges 11 4 V and 16 V in the 12 Volt models 22 8 V and 32 V in the 24 Volt models 45 6 V and 61 V in the 48 Volt models
7. x 1 33 10 at Pnom True sine 230 Vac 3 2 at Pnom From 095 to 10095 load change Normalization 0 5 ms 50 Hz 0 01 Crystal control Adjustable 0 3 gt 20 W 2324 2348 Maximum power 15 min Maximum power 3 min Peak power 5s Asymmetric load Cos o Protections IP protection index Forced ventilation EN 61000 6 1 EN 61000 6 3 EN 55014 EN 55022 EN 61000 3 2 Dir 89 336 EEC LVD 73 23 EEC Overheating protection Required battery capacity Acoustic level EEC conformity Options 3 phased system per unit from SI 1200 TwinPower system from SI 1200 Top cover IP 23 Potential free alarm contact 60V 0 5A for all models Solar charge controller 16A 12 24V for SI 600 and SI 800 Industrial casing in 19 rack 3U x 400 mm from SI 1200 Other specifications on request Ex 115V 60Hz These data are for information only and may change without notice SIxxxxPE SIxxxxTP C IP23 SIxxxxA SIxxxS SIxxxxIND SI in industrial casing 19 rack User manual SI V3 2 1 E 10
8. STUDER INNOTEC SI Sine wave inverter SI SERIES User and Installer Manual STUDER INNOTEC SA Rue des Casernes 57 CH 1950 Sion Tel 41 0 27 205 60 80 Fax 4441 0 27 205 60 88 info studer innotec com 5 Ti UDER www studer innotec com User manual SI V3 2 1 E STUDER INNOTEC Summar INTRODUCTION er 3 NOTE or C 3 APPLICATIONS AND PERFORMANCE eee ee ee ee een nee ee to oeste tone eee see enne eese enne e eese eese en aa 3 PRODUCT PRESENTA TION to o aero o Pe PR pa ke e Eee e PE eR Y pea e eS Ene e Pasa den 3 4 LOCATION one mie enean NeunIeeueINgUeueiNe eee NIU 4 4 CONNECTION p 4 jo C E 4 REMOTE CONTROE eccle eren eterne iiec T demi intu eee ud inei de 4 Sandoy Tevel CI c der tere aud eh a Ges ree ERU n ev 5 Adjustment procedure ECT EI ee qd Ide 5 CCP S 5 INDICATORS E A OE EEE 5 Green Run LED 3 iiis tec tet desddececadsbueysecddesddacsbaeddecdgeetsessduetdaesteet 5 Red Fault LED 5 SABECEY Aor 5 INTERNAL FUSE SER 5 OPTIONS rs LD iss 6 ATARM CONTACT etie EE E ved ubi EE EAE
9. a 3 400V 3 phased grid Connecting 1 Check that the inverters are in OFF position 2 First link together the neutral of all 3 devices by taking care that this connecting point is not further than 1 m from each inverter 3 Link together the battery cables take care to not reverse the polarity The 3 inverters have to be connected together to only one battery bank Commissioning At the time of commissioning it is necessary to operate all the 3 inverters The inverters work independently from each other and can be loaded in an asymmetrical way They can work either in stand by mode or in ON mode see working description in this manual 3 phase recommended wiring 2 24 ur 95 JA RAP pp di User manual 1144 d L max 1 5m A LLO ALT A Line OUT SI V3 2 1 E 9 STUDER INNOTEC Technical data Input voltage Unom V Nominal power W Standby current mA Power ON no load W Power ON no load W TWINPOWER system Maximum efficiency 96 Length L x 124 H x 215 W Weight kg mm Input voltage Dynamic correction of Umin Output voltage Distortion Dynamic behaviour Frequency Charge detection standby SI 612 812 1212 624 824 1224 648 1248 25 21 10 25 21 25 21 12 21 25 17 25 30 2 6 2 8 4 8 5 8 9 13 17 276 276 391 391 591 636 791 69 104 132 152 27 30 Min x 0 95 to Unom
10. esult in its destruction User manual SI V3 2 1 E SI As for the usage of batteries follow the manufacturer s instructions Important After disconnecting the battery the output tension 230V may still remain for 30 seconds The ventilation of the device should never be obstructed Should the device be installed in an enclosed structure make sure that ventilation is possible and adequate The installation and assembly of the device must follow the rules stipulated This document is an essential part of the inverter and must always be carried with it and be at the disposition of anyone working on the installation Applications and Performance As well as its modern design and its technical characteristics the SI inverter is also easy and economical to use in almost all applications All devices working within the public electrical network 230V 50Hz may be used with the inverter up to its nominal power The inverter generates a perfectly sinusoid output tension precisely adjusted by a high technology regulation system Thus the output tension is totally independent of the charge and the fluctuation of tension in the battery All inverters in the SI series are protected against overloading and short circuits Due to obvious safety reasons the inverter is not automatically reactivated after a failure overload short circuit Product presentation The inverters of the SI series are p
11. onsible for damages costs or losses resulting from an installation which is not in accordance with the regulations or inappropriate use or maintenance 13 5V 27V The customer is always responsible for Ubatt the use of the inverters STUDER INNOTEC SA Bat 100 3X A Indicateur LED Charging 14 It is illuminated when the solar module provides current to charge or maintain the battery LED Bat 100 10 It is illuminated when the battery has reached its max tension 14 4V or 28 8V It goes off when the tension is above 13V 26V gt This device has not been designed and is not warranted for use in life support apparatus or any other critical apparatus with potential risks of serious harm to people or to the environment We do not accept any responsibility for any violation of patent rights or other third person rights resulting from the use of the inverter STUDER INNOTEC SA reserves the right to modify their products without previous notice CE declaration of conformity declare under that products mentioned on page 11 of this manual are in conformity with the following standards or standardisation documents EN 61000 6 1 EN 61000 6 3 EN 55014 EN 55022 EN 61000 3 2 Dir 89 336 EEC LVD 73 23 EEC Sion June 19 1999 User manual SI V3 2 1 E Roland Studer Studer Innotec SA STUDER INNOTEC Description and wiring diagram SI 12XX 3548 SI 6XX
12. resented fully equipped with battery cables 230V cable and the user s handbook STUDER INNOTEC Assembly Location The place where the inverter is to be mounted should meet the following requirements Out of reach of non authorised persons In a dry place with no condensation No inflammable material in the same room Not directly on top of the batteries Adequate ventilation Keep min 10 cm distance to other object except mountin P 9 13548 Warning The casing of the inverter may reach high temperatures 80 C Fitting The inverter has been designed to be used in a vertical position and against the wall The inverter is fitted using the four external holes 5 5 mm The fitting screws are not supplied with the inverter Should the inverter be mounted on a flat surface the maximum continuous power of the inverter may be slightly reduced Connection Check the switch 4 is in OFF position First connect the 230V outlet 6 to the user device so as to prevent any possible accidental contact Check the tension and polarity of the battery User manual SI V3 2 1 E SI The tension of the battery should coincide with that mentioned in the technical characteristics of the inverter Battery connection This connection should done be very carefully observing the polarity in order not to damage the device Check that the connections are fixed correctly
13. trial and domestic needs They satisfy the highest demands of comfort safety and reliability Any device designed for the public electrical network of 230V 50 Hz can be connected to them The 51 inverters are the perfect solution as sources of tension in any place where the public network is not available Read the connection instructions thoroughly and give them to the technician who is to install the inverter so as to prevent any malfunction Thus you will have a modern and reliable installation which meets requirements Should you have any doubt or question do not hesitate to contact your specialist salesperson who will give you the best advice Note A deficient assembly could damage the device cause function failures or potential damage to the users The working device generates a high tension which might be fatal in case of contact So any manipulation of the inverter must be carried out with utmost care The following points must be strictly observed The installation of the SI can only be performed by a qualified technician In case of malfunction only a technician specially designated and trained by STUDER INNOTEC is allowed to repair the device Warning Opening the inverters using them incorrectly will result in the immediate loss of the warranty No current or tension generating devices public network generator may be connected to the output of the inverter because this could r
Download Pdf Manuals
Related Search