Owner`s Manual
Contents
1. m S ie 2 GENERAL System Ready green The motor is equipped with a system ready indicator Indicator light will be on when motor is deployed and power is applied to the motor When the motor is properly stowed the indicator light will go off indicating all power has been turned off to the motor If this indicator light does not come on when deployed check that motor is connected to battery properly and motor is completely deployed If indicator light does not go off when stowed be sure that stow deploy lever is fully latched and locked into the stowed position TO STOW Push and hold the stow deploy lever down Gently tilt and pull the composite shaft or control head until the motor engages the motor ramps Motor should rest on the motor ramps and lock into place The stow deploy lever should latch auto matically into the stowed position System ready indicator light green MUST go off for the motor to be stowed properly TO DEPLOY Push in and rotate the stow deploy lever down Gently slide the motor out from the ramps Lower the motor to the desired depth making sure it clicks into a secure vertical position System ready indicator light green will be lit indicating motor is ready for operation TRANSPORTATION In conditions where the stowed motor is subject to high levels of shock or vibration take care to provide a secure stow Move the depth collar snug against the steering motor and tighten System Ready Indicator2. 12 Propeller Replacement pg 13 Maintenance pg 13 Troubleshooting pg 13 20 SYSTEM COMPONENTS COPILOT RIPTIDE ST REMOTE High Speed Bypass n 5 c m Decrease Speed AutoPilot ON OFF Steer Left Increase Speed Steer Right Prop ON OFF COPILOT RIPTIDE ST RECEIVER Preinstalled in sideplate Side Plate Cover Preinstalled Learn Button Specifications subject to change without notice nor mr Depth Drive Collar pe Fall away motor ramps q v 4 5 c 3 o v Factory installed CoPilot Maximizer Permanently Sealed Electronics Wireless remote P Lifetime Warranty Flexible Composite Shaft Cool Running Permanent Magnet Motor Weedless Wedge Propeller 3 Cu Auto Pilot Indicator functional on equipped motors only Push Button Battery Gauge System Ready Indicator Tilt Lock Lever Allows Easy Retraction To Storage Position gt 2 gt rm m D Y 2 INSTALLATION OF THE RIPTIDE ST We recommend that you have another person help with this procedure Tools required 7 16 wrench 3 phillips screw 1 2 driver and electric drill with a 9 32 bit Remove the four sideplate screws Remove the right sideplate and swing the left sideplate out and away from the base extrusion Place the motor on the bow of the boat in the deployed position We recommend that the motor be mounted as close to the cente
3. Federal Regulations CFR 33 183 bateaux et quipement connexe ABYC E 11 AC et DC des syst mes lectriques bord de bateaux Jauge de conducteur et disjoncteur Table de dimensionnement Longueur totale de chef d orchestre Fil Longueur d extension Moteur Disjoncteur pouss e Knee J 1 5 7 5 mI ETA 304 50 Amp 12 VDC 5mm mm 5mm mm 21mm mm bere in Me os 55e 50 S0AmpG i2VDC emm 2 21 3 Le disjoncteur tableau ci dessus de dimensionnement et chef d orchestre est uniquement valable pour les hypoth ses suivantes 1 Pas plus de 3 conducteurs sont regroup s l int rieur d une gaine ou conduites l ext rieur des espaces de moteur 2 Chaque conducteur a 1050c temp valu isolation 8 Pas plus d une chute de tension de 5 a permis la puissance du moteur complet en fonction des besoins de puissance produit publi Tus IS AUNIVERSAL MULTI VOLTAGE DIAGRAM DOUBLE CHECK YOUR MOTORS VOLTAGE FOR PROPER CONNECTIONS Over Current Protection Devices not shown in illustrations zy S ACCE
4. are unobstructed in all locations to avoid damaging the wire insula tion Damage to the insulation could result in failure or injury Always inspect the insulation of the power cables prior to use to ensure they are not damaged Disregarding these safety precautions may result in an electrical short of the battery s and or motor Always disconnect the motor from the battery s before cleaning or checking the propeller Avoid submerging the complete motor as water may enter the lower unit through control head and shaft Water in the lower unit may cause an electrical short and damage the lower unit This damage will not be covered by warranty Caution Always operate the motor in a safe distance away from obstructions Never approach the motor when the propeller is running Contact with a spinning propeller may endanger you or others Always exercise safe practices when using your motor stay clear of other watercrafts swimmers and any floating objects Always obey water regulations applicable to your area of operation Never operate the motor while under the influence of alcohol drugs medication or other substances which may impair your ability to safely operate equipment This motor is not suitable for use in strong currents exceeding the thrust level of the motor The constant noise pressure level of the motor during use is less than 70dB A The overall vibration level does not exceed 2 5m sec gt c Y o gt 2 O
5. ga 1 220 2320201 Cover ctrl box 1 515 2305403 Shrink tube 5 ID x 1 0 Adhesive 4 225 2324032 Ctrl board compass Autpillot only 1 520 2305410 Shrink tube 315 OD x 2 25 3 230 2302960 Grommet compass Autopilot only 3 521 2305415 Shrink tube 472 OD x 2 25 1 235 2305415 Wire insulator 2 525 2991271 Coil cord 60 1 245 2372100 Screw 8 18 x 625 3 530 2320202 Cap dust coil cord non AP only 1 250 2052510 Cable clamp 3 535 2325643 Decal sideplate left 1 255 2322501 Control box 1 540 2323405 Screw 1 4 20 4 260 2332102 Screw 10 24 1 545 2321916 Sideplate left 1 265 2372100 Screw 8 18 x 625 4 550 2323403 Screw 1 4 20 x 375 SS 2 270 2333101 Nut 10 24 1 555 2321927 Skid left 1 275 2224702 Plug ctrl box 1 560 2323422 Screw 10 24 x 375 2 305 2771500 Depth collar assembly 1 565 2321700 Washer 10 SS 2 315 2260906 Knob included in 305 1 570 2322921 Stand off aluminum anodized 2 320 2321706 Washer included in 305 1 571 2323405 Screw 1 4 20 x 1 2 SS 2 321 2323102 Nut included in 305 1 575 2323907 Ramp 4 5 left 1 580 2325117 Pad rubber rest 4 325 2997028 Steering hsg asy includes 330 500 1 585 2321706 Washer 8 4 330 2326502 Steering housing top 1 590 2323412 Screw 8 18 x 25 4 335 2324604 O ring case seal 1 595 2324706 Insert ramp 2 345 2302605 Roll pin 5 16 4 600 2994203 Arm release left 1 This item is part of an assembly This item cannot be sold separately due to machining and or assembly that is req
6. interference received including interference that may cause undesired operation Warning Part 15 21 Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Industry Canada Statement The term IC before the certification registration number only signifies that the Industry Canada technical specifications were met LIMITED LIFETIME WARRANTY ON COMPOSITE SHAFT LIMITED TWO YEAR WARRANTY ON ENTIRE PRODUCT Composite Shaft Johnson Outdoors Marine Electronics Inc warrants to the original pur chaser that the composite shaft of the purchaser s Minn Kota trolling motor is free from defects in materials and workmanship appearing within the original purchaser s lifetime Johnson Outdoors Marine Electronics Inc will provide a new shaft free of charge to replace any composite shaft found to be defective more than two 2 years after the date of pur chase Providing such a new shaft shall be the sole and exclusive liability of Johnson Outdoors Marine Electronics Inc and the sole and exclusive remedy of the purchaser for breach of this warranty and purchaser shall be responsible for installing or for the cost of labor to install any new composite shaft provided by Johnson Outdoors Marine Electronics Inc Entire Product Johnson Outdoors Marine Electronics Inc warrants to the original pur chaser that the purchaser s entire Minn
7. the motor is switched off speed selector on 0 2 Three 12 volt batteries are required LOCATE BATTERY IN A VENTILATED COMPARTMENT 3 The batteries must be wired in series only as directed in wiring dia gram to provide 36 volts SOLID TO BATTERY TERMINALS MAXIMIZERT The built In Maximizer s electronics create pulse width modulation to provide longer running time and extended battery life With the Maximizer speed control you may in some applications experience interference in your depth finder dis play We recommend that you use a separate deep cycle marine battery for your trolling motor and that you power the depth finder from the starting cranking battery If problems still persist call our service department at 1 800 227 6433 x N 2 D Q w m x a BOAT RIGGING AND PRODUCT INSTALLATION For safety and compliance reasons we recommend that you follow American Boat and Yacht Council ABYC standards when rigging your boat Altering boat wiring should be completed by a qualified marine technician The following specifications are for general guidelines only CAUTION These guidelines apply to general rigging to support your Minn Kota motor Powering multiple motors or additional electrical devices from the same power circuit may impact the recommended conductor gauge and circuit breaker size If you are using wire longer than that provided with your unit follow the conductor gauge and c
8. trolling motor is free from defects in materials and workmanship appearing within two 2 years after the date of purchase Johnson Outdoors Marine Electronics Inc will at its option either repair or replace free of charge any parts including any composite shaft found to be defective during the term of this warran ty Such repair or replacement shall be the sole and exclusive liability of Johnson Outdoors Marine Electronics Inc and the sole and exclusive remedy of the purchaser for breach of this warranty Terms Applicable to Both Warranties These limited warranties do not apply to motors used commercially nor do they cover normal wear and tear blemishes that do not affect the opera tion of the motor or damage caused by accidents abuse alteration modi fication misuse or improper care or maintenance DAMAGE TO MOTORS CAUSED BY THE USE OF REPLACEMENT PROPELLERS OR OTHER REPLACEMENT PARTS NOT MEETING THE DESIGN SPECIFICA TIONS OF THE ORIGINAL PROPELLER AND PARTS WILL NOT BE COVERED BY THIS LIMITED WARRANTY The cost of normal mainte nance or replacement parts which are not defective are the responsibility of the purchaser To obtain warranty service in the U S the motor or part believed to be defective and proof of original purchase including the date of purchase must be presented to a Minn Kota Authorized Service Center or to Minn Kota s factory service center in Mankato MN Any charges incurred for service calls tra
9. 8129 3ONVISISSV TVIINHDAL m e m gt S lt D y pa gt 2 FREQUENTLY ASKED QUESTIONS PO PO PO PO Are there any on off switches No The receiver is always powered up whenever the motor is deployed and connected to the battery or batteries The remote automatically goes into a low power sleep mode whenever there are no buttons being pressed Does the remote float The remote will float by itself Can other CoPilot users control my CoPilot if they get too close No Each remote has it s own unique ID number your CoPilot receiver will not respond to commands from other unlearned remotes How many remote ID numbers can my receiver learn 10 What happens if my receiver has 10 different remote ID numbers learned and 1 attempt to teach it another one The first remote ID number that was learned will be erased first in first out How long should the battery in the remote last Under normal use and conditions the battery should last for at least two regular fishing seasons Where can purchase additional remotes Through any regular Minn Kota retail outlet FCC DISCLAIMER Compliance Statement Part 15 19 This device complies with Part 15 of the FCC Rules and with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any
10. LES ni Master User Manual for RIPTIDEST NOTE DO NOT RETURN YOUR MINN KOTA MOTOR TO YOUR RETAILER YOUR RETAILER IS NOT AUTHORIZED TO REPAIR OR REPLACE THIS UNIT YOU MAY OBTAIN SERVICE BY CALLING MINN KOTA AT 1 800 227 6433 OR 1 507 345 4623 RETURNING YOUR MOTOR TO THE MINN KOTA FACTORY SERVICE CENTER SENDING OR TAKING YOUR MOTOR TO ANY MINN KOTA AUTHORIZED SERVICE CENTER ON ENCLOSED LIST PLEASE INCLUDE PROOF OF PURCHASE SERIAL NUMBER AND PURCHASE DATE FOR WARRANTY SERVICE WITH ANY OF THE ABOVE OPTIONS PLEASE THOROUGHLY READ THIS USER MANU AL FOLLOW ALL INSTRUCTIONS AND HEED ALL SAFETY amp CAUTIONARY NOTICES BELOW USE OF THIS MOTOR IS ONLY PERMITTED FOR PERSONS THAT HAVE READ AND UNDERSTOOD THESE USER INSTRUCTIONS MINORS MAY USE THIS MOTOR ONLY UNDER ADULT SUPERVISION SERIAL NUMBER Copilot Control Autopilot Saltwater olling Motors Y PURCHASE DATE Riptide ST CoPilot Features pg 2 3 Feature Information pg 14 Installation pg 4 Adding Removing Remotes pg 14 Cautions pg 5 Misc Information pg 15 Operation pg 6 Battery Replacement pg 15 Controls pg 7 General Operation pg 16 Adjustments pg 7 Audio Modes pg 16 17 Battery Information pg 8 Troubleshooting pg 17 Circuit Breaker pg 10 11 Technical Assistance pg 17 Battery Connections pg 9 FAQ s FCC Disclaimer pg 18 Maximizer pg 9 Limited Warranty pg 19 Wiring Diagram pg
11. ODE 3 COPILOT TROUBLESHOOTING SAGOW OIGNV AUDIO OCCURS IN WHAT CONDITION CAUSES IT WHICH AUDIO PATTERN MODE 1 be Pressing the INCREASE SPEED or DECREASE SPEED Modes 2 and button 3 1 Bes Pressing the PROP ON OFF button to turn the Modes 2 and P prop on 3 2 beeps Pressing the PROP ON OFF button to turn the Mode 2 and 3 prop off Single tick every 1 5 sec When the prop is active including when speed is Mod set to 0 pug Switching to Audio Mode 1 pressing the 1 beep INCREASE SPEED and DECREASE SPEED buttons All simultaneously for 1 second Switching to Audio Mode 2 pressing the 2 beeps INCREASE SPEED and DECREASE SPEED buttons Al simultaneously for 1 second Switching to Audio Mode 3 pressing the 3 beeps INCREASE SPEED and DECREASE SPEED buttons All simultaneously for 1 second Every time the receiver is powered up and there is at least one remote ID learned AUDIO OCCURS IN WHAT CONDITION CAUSES IT WHICH AUDIO PATTERN MODE 2 second long Every time the receiver is powered up an there are no remote All D beep IDs learned 5besps Foot pedal speed control is moved after speed has been adjusted with remote All E Steady tone Heard while holding down the learn button on the receiver e 4 beeps After a remote button is pressed while the receiver learns it s ID A ten second long warbling Heard during the pr
12. SSORY PLUG STEERING MOTOR BATTERY GAUGE RED e WHITE OO Og BLACK COMPASS m BLACK C O ACCESSORY PLUG 2 E T 5 de M ga AUTOPILOT INDICATOR RED 2 RED M lt 3 b Z H 2 d ad SYSTEM READY INDICATOR GREEN 5 B d EA i D 8 9 a v REED SWITCH a 9 z 3 E sd E o RED B E z 2 SENSOR o E Ho 5 E BE 9 zi amp 1 a S a E V 1 B 5 lt a FOOT PEDAL ACCESORIO CONTROL BOARD E 1 qe 3 6 Og l BATTERY 1 o 1 l a Bros J E A AAA ez 2 ia ii ii i SS 5 amp lt ox 22 oli a 5 ow RED M 25 15 58 Ey 2 a zin lt ao 52 o5 ac E a gt O BLACK M SZ A MOTOR BATTERY 2 BATTERY 3 PROPELLER REPLACEMENT 4a MOTOR MAINTENANCE Le NOTICE DO NOT APPLY LUBRICANT OR ANY TYPE OF GREASE TO TROLLING MOTOR CONNECTORS MOTOR TROUBLESHOOTING 1 2 3 Motor is hard to steer 4 Motor does not respond to foot pedal commands 5 Control head vibrates during normal operation NOTE For all other malfunctions see enclosed authorized service center listing for nearest service center The propeller must be cleaned of weeds and fishing line The line can get behind the prop wear away the seals and allow To prevent accidental damage during trailering or storage disconnect the battery whenever the motor is off of the water For For maximum performance restore battery t
13. Tilt Lock Lever Operation Fall away motor ramps 1 PUSH IN WARNING WHEN RAISING OR LOWERING MOTOR KEEP FINGERS CLEAR OF ALL HINGE AND PIVOT a POINTS AND ALL MOVING PARTS 2 PUSH DOWN TO DEPLOY AUTOPILOT CONTROLS AUTOPILOT ON EQUIPPED MOTORS ONLY The MINNKOTA AutoPilot uses a magnetic compass and a microprocessor chip to keep the trolling motor pointed in the direction you want to go Each time the wind or water current moves the boat off course the AutoPilot senses the change and steers itself back to the original heading The AutoPilot direction is set every time a steering change is made To change direction steer until the control head points to the desired course The AutoPilot will pull the bow of the boat around and correct automatically until the boat is moving in the direction you chose 1 This unit has an automatic steering shutdown for safety In conditions where an obstruction prevents the trolling motor from turning or in extremely windy conditions the automatic steering may stop Any steering input on the foot pedal will reset the system to normal 2 When the AutoPilot is on and the trolling motor is pulled out of the water to the stow position the steering motor will continue to run until the motor is stowed properly Once the motor is stowed properly AutoPilot will turn off and the System ready indicator will go off 3 This unit uses a magnetic compass to detect direction of travel The compass can be advers
14. attery with at least an 115 ampere hour rating The actual ampere draw is subject to your particular environmental conditions and operation requirements Maintain battery at full charge Proper care will significantly improve the battery life Failure to recharge lead acid batteries within 12 24 hours is the leading cause of premature battery failure For best results use a variable rate MinnKota charger If you are using a crank battery to start a gasoline outboard we recommend that you use a separate deep cycle marine battery for your trolling motor Advice regarding batteries Never connect the and the terminals of the battery together Take care that no metal object can fall onto the battery and short the terminals This would immediately lead to a short and utmost fire danger Recommendation Use battery boxes and covered battery terminal clamps like Minn Kota accessory 1 The motor is equipped with a battery gauge This LED gauge provides an accurate display of the remaining charge in the battery The gauge is only accurate when the motor is off The gauge reads as Four lights full charge Three lights good charge Two lights low charge One light recharge BATTERY CONNECTION a Connect a connector cable to positive terminal of battery 1 and to negative terminal of battery 2 wm 12 Volt Systems b Connect a connector cable to positive terminal of battery 1 Make sure that th
15. board 4 Pull back the retaining fingers of the battery holder to remove the battery underside of circuit board 5 Install the new battery with the positive side of the battery facing up away from the circuit board Ensure battery is snapped securely in place 6 Reassemble the remote Note that the alignment peg in the remote case must line up with the corresponding alignment hole in the circuit board Also note that the keypad must be positioned so that the buttons are over the end of the circuit board opposite from the alignment peg and hole Reinstall the four case screws and tighten them as required BATTERY ALIGNMENT PEG GENERAL OPERATION Using the CoPilot with the corded foot pedal The CoPilot Riptide ST and corded foot pedal can be used for motor control simultaneously The corded foot pedal and CoPilot remote operate on a first in line priority basis If a button is pressed and held down on the foot pedal and a button with the same function is then press on the remote the foot pedal will have priority The remote would have priority if the remote was first to send the command NOILVWAOZNI OSIN 0 gt A lt A 0 m D m 2 im Multiple functions can be done at the same time For instance AutoPilot can be tumed on or off at the same time speed is being adjusted on the foot pedal If the momentary button is being held down on the corded foot pedal steering adjustments can be made at the
16. c legal rights and you may also have other legal rights which vary from state to state WARNING This product contains chemical s known to the state of California to cause cancer and or reproductive toxicity ENVIRONMENTAL COMPLIANCE STATEMENT It is the intention of Johnson Outdoors Marine Electronics Inc to be a responsible corporate citizen operating in compliance with known and applicable environmental regulations and a good neighbor in the communities where we make or sell our products WEEE Directive EU Directive 2002 96 EC Waste of Electrical and Electronic Equipment Directive WEEE impacts most distributors sellers and manufacturers of consumer electronics in the European Union The WEEE Directive requires the producer of consum er electronics to take responsibility for the management of waste from their products to achieve environmentally responsible disposal during the product life cycle WEEE compliance may not be required in your location for electrical amp electronic equipment EEE nor may it be required for EEE designed and intended as fixed or temporary installation in transportation vehicles such as automobiles aircraft and boats In some European Union member states these vehicles are considered outside of the scope of the Directive and EEE for those applications can be considered excluded from the WEEE Directive requirement This symbol WEEE wheelie bin on product indicates the product must not be disp
17. d Questions under the Service tab to find an answer to your question http www minnkotamotors com service faq aspx linkidentifier id amp itemid 817 ED AUTHORIZED SERVICE CENTERS Minn Kota has over 300 authorized service centers in the United States and Canada where you can purchase parts or get your products repaired Please visit www minnkotamotors com and click on Service Center Locator under the Service tab to locate a service center in your area http www minnkotamotors com service asclocator aspx S s CALL US FOR U S AND CANADA Our customer service representatives are available Monday Friday between 7 00am 4 30pm CST at 800 227 6433 If you are calling to order parts please have the 11 character serial number from your product specific part numbers and credit card information available This will help expedite your call and allow us to provide you with the best customer service possible You can reference the parts list located in your manual to identify the specific part numbers DA emai us You can email our customer service department with questions regarding your Minn Kota products To email your quesiton visit www minnkotamotors com and click on Contact Us under the Service tab http www minnkotamotors com service contact aspx 112 5 112 LBS THRUST 36 VOLT 52 AMPS 60 SHAFT This page provides MinnKota amp WEEE compliance disassembly instructions For more information about wh
18. e motor is Switched off speed selector on 0 2 and to negative terminal of battery 3 2 Connect positive red lead to positive battery terminal c Connect positive red lead to positive terminal on bat m 3 Connect negative black lead to negative battery terminal tery 3 m 4 For safety reasons do not switch the motor on until the propeller d Connect negative black lead to negative terminal of lt is in the water battery 1 4 For safety reasons do not switch the motor on until the propeller Me 24 Volt Systems is in the water 1 Make sure that the motor is switched off speed selector on 0 2 Two 12 volt batteries are required m 3 The batteries must be wired in series only as directed in wiring If installing a leadwire plug observe proper polarity and fol diagram to provide 24 volts low instructions in your boat owner s manual a Connect a connector cable to positive terminal of battery 2 gt 1 and to negative terminal of battery 2 See wiring diagram on following pages b Connect positive red lead to positive terminal on bat tery 2 c Connect negative black lead to negative terminal of battery 1 4 For safety reasons do not switch the motor on until the propeller IMPROPER WIRING OF 24 VOLT SYSTEM COULD CAUSE is in the water BATTERY EXPLOSION 36 Volt Systems KEEP LEADWIRE WING NUT CONNECTION TIGHT AND 1 Make sure that
19. ely affected by magnets or large ferrous metal objects near within 12 of the trolling motor control head 4 After steering to a new direction there is a short delay before the direction is locked in to allow the compass to stabi lize 5 Obstructions on the propeller may cause excessive vibration of the motor head This vibration can cause the compass to wander and erratic steering to occur Clear the obstruction to return the motor to normal operation 6 When broad speed changes are made the motor heading may change slightly This is normal DEPTH ADJUSTMENTS Firmly grasp and hold the composite shaft above the PowerDrive housing Loosen the depth drive collar knob until the shaft slides freely Raise or lower the motor to the desired depth Tighten the depth drive collar knob to secure the motor in place EXTERNAL TRANSDUCER INSTALLATION Transducer cables should be routed through the coil cable and han dle as shown Leave enough slack for proper deployment and retraction Mount transducer according to transducer instructions NOTE An external transducer is included with your trolling motor Leave slack hy Tie wrap cable STOYLNOD 5 2 5 9 00 gt J 2 lt gt 2 Y 2 BATTERY INFORMATION The motor will operate with any deep cycle marine 12 volt battery 24 volts require two and 36 volts requires three For best results use a deep cycle MinnKota marine b
20. ere you should dispose of your waste equipment for recycling and recovery and or your European Union member state requirements please contact your dealer or distributor from which your product was purchased Tools required Flat head screw driver Phillips screw driver Socket set Pliers Wire cutters A AutoPilot Equipped Motors Only E Ay 321 902 LE gt In the U S A replacement parts may be ordered directly from MINN KOTA Parts Dept 121 Power Drive P O Box 8129 Mankato Minnesota 56002 8129 In Canada parts may be ordered from any of the Canadian Authorized Service Centers shown on the enclosed list Be sure to provide the and seriaL numbers of your motor ordering parts Please use the correct part numbers parts VISA To order cali 1 800 227 6433 or FAX 1 800 527 4464 Re Item P N Description Qty Item P N Description Qty 1 2777091 36V Motor 60 SW w tube 1 350 2308601 Breather filter 1 r 5 2 100 245 Armature assembly 1 360 2302240 Pinion gear 1 o 10 140 014 Bearing 1 365 2300265 Cap motor plastic 1 mE 15 788 040 Retaining ring 1 m 2777024 Dual steering motor assembly 36V 20 Center hsg w tube Included in 200 370 2777025 Motor steering 36V 1 25 2 300 151 Brush end housing assembly 1 380 2302255 Gear cluster 3rd stage 1 30 421 241 Plain end housing assembly SW 1 385 2302250 Gear cluster 2nd stage 1 35 144 017 Flange bearing 1 390 2302245 Gear cluste
21. he battery AFINVNALNIVN YOLOW lubrication for proper retraction and deployment A coating of Armor AII amp will provide like new operation performance the leading edge of the blades must be kept smooth If this edge is rough or nicked restore to smooth by sand ing with fine sandpaper Motor fails to run or lacks power Check battery connections for proper polarity Make sure terminals are clean and corrosion free Check battery water level Add water if needed Motor loses power after a short running time Check battery batteries charge if low restore to full charge Make sure the drive depth collar is tight and fully engaged with the drive motor Lubricate the composite shaft ONILOOHSATENOUL dOLON Make sure the cable connector plugs at the drive mount are secure Remove and rotate the prop 180 See removal instructions in prop section S3YNLVAsA 1011909 gt 9 gt m D SYSTEM FEATURES CoPilot for Riptide ST setup and use instructions Your motor is factory installed with CoPilot for Riptide ST Wireless control for Riptide ST Plug n play design allows for easy hook up Functions include steering right left prop on off AutoPilot on off high speed bypass and speed control Receiver mounts into the right side plate of the Riptide ST motor for seamless installation Remote allows motor to be controlled from anywhere in the boat Copil
22. ilot the AUTOPILOT ON OFF button will be non functional Pressing the HIGH SPEED BYPASS button toggles the speed between the current setting and the maximum setting level 10 Pressing the button sets the motor at speed 10 instantly pressing the button again sets the motor speed back to the previous Speed setting Pressing and releasing the INCREASE SPEED or DECREASE SPEED buttons will cause the speed to increase or decrease by one level The speed is adjustable from level 0 10 At level 0 the prop will not turn An audible beep is heard for each step change in speed Attempting to go higher than speed 10 or lower than speed 0 will result in the speed not changing and no beep will be heard See the Audio Mode section for more information If the receiver senses no foot pedal or remote operation for 1 hour the remote speed setting is automatically set to zero This could help prevent unintentional activation of the propeller if the prop on off remote button is inadvertently pressed or bumped while in storage BATTERY REPLACEMENT THE REPLACEMENT BATTERY MUST BE A MODEL CR2032 COIN CELL TYPE IT IS STRONGLY REC OMMENDED THAT A NAME BRAND BATTERY IS USED To replace the battery follow these steps 1 Temporarily ground yourself by touching a grounded metal object in order to discharge any static electricity in your body 2 Remove the four screws on the bottom of the remote case 3 Separate the case halves to access the circuit
23. ircuit breaker sizing table below If your wire extension length is more than 25 feet we recommend that you contact a qualified marine technician An over current protection device circuit breaker or fuse must be used Coast Guard requirements dictate that each ungrounded current carrying conductor must be protected by a manually reset trip free circuit breaker or fuse The type voltage and current rating of the fuse or circuit breaker must be sized accordingly to the troll ing motor used The table below gives recommended guidelines for the circuit breaker sizing Reference United States Code of Federal Regulations 33 CFR 183 Boats and Associated Equipment ABYC E 11 AC and DC Electrical Systems on Boats Conductor Gauge and Circuit Breaker Sizing Table Max Wire Extension Length motor Amp Circuit Breaker Thrust Draw 30 10AWG 10AWG 8AWG 6 AWG 4 AWG 50 Amp 12 VDC 40 45 10AWG 8AWG 6 AWG 4 AWG 4 AWG 55 60 Amp 12 VDC 8AWG 6 AWG 4 AWG 4 AWG 2 AWG 70 80 The conductor and circuit breaker sizing table above is only valid for the following assumptions 1 No more than three 3 conductors are bundled together inside a sheath or conduit outside of engine spaces 2 Each conductor has 105 degree C temp rated insulation 3 more than 5 voltage drop allowed at full motor power based on published product power requirements BATEAU GR EMENT ET PRODUIT DE L INSTALLATION Pour des rais
24. l sideplate right Re ltem P N Description Qty ltem P N Description Qty 605 2322710 Spring extension 1015 2091701 Washer prop large 1 P Ci 2770251 Cover speed control with decal 1020 2198401 Nut Anode nylock prop large 1 r o im a 2994864 Mounting hardware bag assy ax pm aSnrna2a29aana2aNa2a2NNNNaa2a2ayNaanahanNanN 850 2994095 Remote assembly 1 851 2372502 Case cover transmitter 1 860 2375112 Keypad transmitter 1 865 Transmitter board 1 870 Battery transmitter 1 875 2372505 Case bottom transmitter 1 880 2373440 Screw 4 24 4 a 1378160 Propeller kit WW2 1000 1020 L 2994876 Propeller bag assy 1010 1020 1000 2341160 Propeller WW2 1 1010 2262658 Drive pin large 1 P N 2324945 REV A ECN 34956 12 13 Minn Kota accessories available for your motor OnBoard Chargers Portable Chargers Quick Release Brackets ED csse a gt War Y 184068 ROO cJ lt Stabilizer Kits gt Circuit Breakers Z9 2822 DTA Anywhere Anytime Visit our website at www minnkotamotors com 2010 Johnson Outdoors Marine Electronics Inc p n 2327103 REV L ECN 34956 12 13
25. nsportation or shipping freight to from the Minn Kota Authorized Service Center or factory labor to haul out remove re install or re rig products removed for warranty service or any other similar items are the sole and exclusive responsibility of the purchaser Motors pur chased outside of the U S must be returned pre paid with proof of purchase including the date of purchase and serial number to any Authorized Minn Kota amp Service Center in the country of purchase Warranty service can be arranged by contacting a Minn Kota Authorized Service Center listed on the enclosed sheet or by contacting the factory at 1 800 227 6433 or fax 1 800 527 4464 Note Do not return your Minn Kota motor to your retailer Your retailer is not authorized to repair or replace them S 3 gt 2 im lt THERE ARE NO EXPRESS WARRANTIES OTHER THAN THESE LIM ITED WARRANTIES IN NO EVENT SHALL ANY IMPLIED WAR RANTIES EXCEPT ON THE COMPOSITE SHAFT INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE EXTEND BEYOND TWO YEARS FROM THE DATE OF PURCHASE IN NO EVENT SHALL JOHNSON OUT DOORS MARINE ELECTRONICS INC BE LIABLE FOR INCIDENTAL CONSEQUENTIAL OR SPECIAL DAMAGES Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations and or exclusions may not apply to you This warran ty gives you specifi
26. o full charge before each use Unless you are using a power panel or The composite shaft requires periodic cleaning and The weedless wedge propeller is designed to provide absolute weed free operation with very high efficiency To maintain top WEEDLESS y Disconnect motor from battery prior to changing the PROPELLER 2 propeller e Hold the propeller and loosen the prop nut with a pliers ANODE NUT m or a wrench m Remove prop nut and washer If the drive pin is sheared m broken you will need to hold the shaft steady with a m screwdriver blade pressed into the slot on the end of the shaft Turn the old prop to horizontal as illustrated and pull it straight off If drive pin falls out push it back in Align new propeller with drive pin Install prop washer and prop nut WASHER Tighten prop nut 1 4 turn past snug 25 35 inch Ibs Be careful over tightening can damage prop CAUTION DISCONNECT THE MOTOR FROM THE BATTERY BEFORE BEGINNING ANY PROP WORK OR MAINTENANCE DRIVE PIN Y After use in salt or brackish water these units should be rinsed with fresh water then wiped down with a cloth dampened with an aqueous based silicone spray such as Armor All water to enter the motor Disconnect battery and check this after every 20 hours of operation prolonged storage lightly coat all metal parts with silicone spray MINNKOTA battery charger disconnect the trolling motor when charging t
27. ocess used to clear all stored remote IDs sound that After the learn switch is released a 2 second long beep will be transitions intoa heard steady tone TECHNICAL ASSISTANCE CAUSE EFFECT SOLUTION REMOTE IS NOT TRANSMITTING The battery is discharged Replace battery Receiver may not have learned the ID number of the remote Remote needs to be learned See ADDING REMOVING REMOTES section to learn the remote ID number If remote has been taken apart the keypad and top case may have been installed backwards Take remote apart BATTERY REPLACEMENT SECTION and reinstall case halves with the proper orientation THE PROP IS NOT TURNING BUT THE PROP ON AUDIO TICK IS STILL GOING Prop speed is set at 0 Increase the prop speed above NO Prop ON tick occurs only in Audio mode 3 Switch Audio mode to either Audio 1 or 2 See Audio Modes section Q o rm 4 D e 00 rm m I Q Y 19 Do not take your CoPilot receiver or remote to your dealer or a Minn Kota Authorized Service Center for repair or replace ment The CoPilot remote has no field replaceable or user serviceable parts other than battery replacement For service technical assistance call 1 800 227 6433 or send the CoPilot receiver and remote s along with proof of purchase date to Johnson Outdoors MinnKota Service 121 Power Drive Mankato MN 56002
28. ons de s curit et de conformit nous recommandons de suivre les normes de l American Boat And Yacht Council ABYC lorsque truquer votre bateau Modifier le c blage du bateau doit tre compl t par un technicien marin qualifi Les sp cifications suivantes sont uniquement des directives g n rales Avertissement Ces directives s appliquent au gr ement g n rale l appui de votre moteur Minn Kota Alimenter plusieurs moteurs ou des dispositifs lectriques suppl mentaires depuis le m me circuit de puissance peut influencer la taille recommand e de la jauge du conducteur et disjoncteur Si vous utilisez fil plus long que celui fourni avec votre unit suivre le conducteur jauge et le disjoncteur dimensionnement tableau ci dessous Si votre fil longueur d extension est plus de 7 5 metres nous recommandons que vous contacter un technicien marin qualifi 2 D Q S w m m a Un dispositif de protection de surintensit disjoncteur ou fusible doit tre utilis Les exigences de la Garde C te am ricain disent que chaque conducteur sans fondement de porteurs de courant doit tre prot g par un disjoncteur mise en circuit a d clenchement libre ou un fusible Le type tension et courant nom inal du fusible ou disjoncteur doit tre dimensionn en cons quence pour le moteur utilis Le tableau ci des sous donne les directives pour le calibrage de disjoncteur R f rence United States Code of
29. osed of with other household refuse It must be disposed of and collected for recycling and recovery of waste EEE Johnson Outdoors Marine Electronics Inc will mark all EEE products in accordance with the WEEE Directive It is our goal to com ply in the collection treatment recovery and environmentally sound disposal of those products however these requirement do vary within European Union member states For more information about where you should dispose of your waste equipment for recycling and recovery and or your European Union member state requirements please contact your dealer or distributor from which your product was purchased Disposal Minn Kota motors are not subject to the disposal regulations EAG VO electric devices directive that imple ments the WEEE directive Nevertheless never dispose of your Minn Kota motor in a garbage bin but at the proper place of collection of your local town council Never dispose of battery in a garbage bin Comply with the disposal directions of the manufacturer or his representative and dispose of them at the proper place of collection of your local town council REPAIR AND TROUBLESHOOTING We offer several options to help you troubleshoot and or repair your product Please read through the options listed belou FREQUENTLY ASKED QUESTIONS Did you know that we have over 100 FAQ s to help answer all of your Minn Kota questions Visit www minnkotamotors com and click on Frequently Aske
30. ot Riptide ST can be used with or without the corded foot pedal Remote will not interfere with Autopilot or Universal Sonar Operation Up to 10 remotes can be used interchangeably with the same receiver Components are environmentally sealed to protect against rain wind or snow ADDING REMOVING REMOTES THE COPILOT RECEIVER IN THIS KIT HAS ALREADY LEARNED THE ID NUMBER OF THE REMOTE IT IS PACKAGED WITH THE RECEIVER MUST LEARN THE ID NUMBER OF ANY ADDITIONAL REMOTE S THAT YOU INTEND TO USE WHEN THE RECEIVER LEARNS THE ID NUMBER OF A REMOTE THAT ID NUMBER IS RETAINED IN THE RECEIVER EVEN WHEN THE MOTOR IS DISCONNECTED FROM ITS POWER SOURCE To learn the ID number of additional remotes follow these steps 1 The system ready light must be on To do so push in the release handle and rotate it down 2 Press and hold the LEARN button located on the side of the receiver receiver will emit a continuous tone A small blunt object must be used to depress the LEARN button pen or screwdriver 3 Press any button on the remote receiver will beep 4 times confirming that it has learned the ID number of the remote and that the programming is valid and complete Re leaming the ID number of the same remote will not overwrite previously learned remotes If the receiver has learned the ID number of ten remotes learning an eleventh remote will erase or over write the first learned remote The CoPilo
31. r 1st stage 1 40 880 025 Seal 2 395 2302610 Shaft gear 1st stage 1 41 725 095 Paper tube seal bore 1 400 2302620 Shaft gear 3rd stage 1 50 188 095 Brush 2 405 2302615 Shaft gear 2nd stage 1 60 9 738 011 Brush plate assembly 1 410 2321704 Washer thrust 2 65 975 045 Brush spring 2 415 2321515 Liner output tube 2 a 2881450 Seal amp Oring Kit includes 40 70 80 420 2324608 O ring 224 2 70 701 098 O ring plain end 1 425 2321720 Shim O ring 2 71 701 046 O ring brush end 1 430 2327315 Bushing Aluminum Spacer 2 80 701 009 O ring thru bolt 2 435 2322200 Gear output 1 85 2053410 Screw 10 32 x 1 2 2 440 2327314 Bushing Pro Steering SW 2 90 830 094 Thru bolt 12 24 2 445 2322031 Tube output machined 1 95 990 051 Washer steel 2 450 2321510 Collar drive bottom 1 100 990 052 Washer nylatron 2 455 2326507 Steering housing Bottom 1 110 2777312 Ferrite bead w shrink 1 460 2320605 Leadwire Steering 1 115 992 011 Washer belleville 2 465 2322601 Pin latch SS 1 120 990 011 Washer shim 1 470 2322603 Pin pivot SS 1 125 582 016 Clip retaining sonar 1 475 2327310 Bushing pivot pin 2 135 640 044 Leadwire black 60 1 480 2321702 Washer flat 375 2 136 640 144 Leadwire red 60 1 485 2263011 E ring 375 2 490 2322702 Spring latch pin 2 200 2777345 Tube comp 60 SW includes 20 1 495 2323410 Screw 8 32 x 75 1 500 2323408 Screw 8 32 x 2 7 210 2325666 Decal cover 2 215 2325690 Decal ctrl box cover RT Autopilot 1 510 2090651 Leawire 10
32. rline of the boat as possible Make sure the bow area under the mounting location is clear and unobstructed for drilling and accessible for you to attach the nuts and washers Make sure the mount is positioned so that the shaft is out beyond the rub strip of the boat by 1 1 2 The lower unit as it is lowered into the water or raised into the boat must not encounter any obstructions Once in position mark four of the six holes provided in the bow mount base for drilling If possible use the four holes that are farthest apart Drill through the marked holes using a the 9 32 drill bit Mount the plate to the bow using the provided bolts nuts and washers Replace the sideplates and sideplate screws Mount Bracket so that during stow and deploy the shaft will not encounter boat s rub strip Mounting Holes Le fait de Monter des Trous CAUTION MAKE SURE YOU MOUNT YOUR MOTOR ONALEVEL SURFACE USE THE RUBBER WASHERS TO CREATE A LEVEL SURFACE IF NECESSARY Attention Avoid running your motor with the propeller outside of the water This may result in injuries from the rotat ing propeller lt is recommended to set the speed selector to zero and place the motor in the deployed position prior to connecting power cables Disconnect power cables prior to stowing Always ensure that the power cables are not twisted or kinked and that they are securely routed to avoid a safety or trip hazard Ensure cables
33. same time from the remote When the momentary button is being held down on the corded foot pedal speed increase decrease and prop on off will not function on the remote When the foot pedal has priority over the remote and remote commands are received the receiver will emit and audible chirp This will indicate that the remote is functioning properly however the foot pedal is taking priority Using the CoPilot without the corded foot pedal Some anglers will prefer to have the deck completely clear of any unnecessary cables and foot pedals When using the Copilot in this manner the receiver will always react to any commands from the remote m S rm S gt gt AUDIO MODES There are three receiver audio modes available To switch from one audio mode to another press and hold both the INCREASE and DECREASE speed buttons on the remote down for one second The receiver will respond with 1 2 or 3 audible beeps indicating the corresponding receiver audio mode change Audio Mode 1 All of the normal audible sounds mentioned in this owners manual Audio Mode 2 Same as audio mode 1 plus an audible beep for speed increase decrease and prop on off UNIT IS FACTORY PRE SET TO AUDIO MODE 2 Audio Mode 3 Same as audio mode 2 plus the prop on audible click every few seconds NOTE WHEN THE CORDED FOOT PEDAL IS IN CONTROL AND THE PROPELLER IS ON THE PROP ON INDICATOR CLICK WILL BE HEARD IF THE RECEIVER IS SET TO AUDIO M
34. t allows the angler to erase all stored remote ID numbers from the receiver To do so follow these steps 1 Remove power from the receiver by stowing the motor 2 Press and hold the LEARN button and power up the receiver by pushing in the release handle and rotate it down Hold the LEARN button down for 10 seconds During this time the receiver audio will emit a warble sound slowly transition to a constant beep and then shut off 3 Release the Learn button and the receiver will reboot The receiver will emit a 2 second long beep indicating memory is empty This audio panen will occur each time the receiver powers up until a remote ID number is learned a F or gt Learn Button MISCELLANEOUS INFORMATION The seven buttons are for PROP ON OFF STEER LEFT STEER RIGHT AUTOPILOT ON OFF HIGH SPEED BYPASS INCREASE SPEED AND DECREASE SPEED Pressing the PROP ON OFF button will tum the propeller on or off The button does not need to be held down Press the button once to turn the motor ON press button a second time to turn it OFF Pressing either STEERING button will cause the motor to turn in the desired direction as long as the button is held down If a Steering button is held for more than seven seconds the steering will automatically stop Pressing the AUTOPILOT ON OFF button will turn the autopilot on or off The button does not need to be held down If the motor does not have AutoP
35. uired Fuera de los Estados Unidos consultar la lista anexa para ubicar el Centro de servicio autorizado MINN KOTA No dejar de incluir el n mero del MODELO y el n mero de SERIE del motor para el cual se solicitan las piezas Usar siempre los n meros de pieza correctos indicados en la lista de piezas 620 2325651 Decal speed control 625 2320211 Cover speed control 630 2322901 Strain relief L 2884050 Switch reed repair kit 635 2324017 Control board 24 36v 636 2320208 Dust plug 640 2320203 Cap dust control board 645 2323406 Screw 10 24 x 650 2321315 Holder connector 655 2332103 Screw 6 20 x 375 660 2074082 Battery meter 36v 665 2323402 Screw 1 4 20 x 375 670 2321941 Bracket strain relief 675 2321310 Strain relief wire 680 2323405 Screw 1 4 20 x 5 685 2333100 Speed nut 375 690 2320216 Handle release cover 695 2301700 Bushing 700 2322701 Spring release handle 710 2320401 Handle release SW 715 2322712 Spring release handle 720 2322604 Bushing handle 725 2332104 Screw 1 4 20 x 625 730 2323000 E clip 3 16 SS 735 2322607 Pin follower handle 740 2321906 Base extrusion machined 741 2321721 Shim 2 x 4 x 025 745 2322912 Spring pin 750 2321951 Bracket sideplate 755 2323902 Ramp 4 5 right 757 2994201 Arm release Right 760 2321922 Skid right 765 2301310 Screw 8 18 x 5 770 2370221 Cover access SW 772 2374097 Copilot Reciever Board 775 2321911 Sideplate right SW 780 2325642 Deca
Download Pdf Manuals
Related Search