Ball Camera - Surveillance
Contents
1. Everything s Digital Ball Camera DWC BL2651TIR STAR LIGHT MPR Before installing and using the camera please read this manual carefully Be sure to keep it handy for future reference ABOUT MANUAL 12172014 PRECAUTIONS Do not open or modify Do not open the case except during maintenence and installation for it may be dangerous and can cause damages Do not put objects into the unit Keep metal objects and flammable substances from entering the camera It can cause fire short circuits or other damages Be careful when handling the unit To prevent damages do not drop the camera or subject it to shock or vibration Do not install near electric or magnetic fields Protect from humidity and dust Protect from high temperature Be careful when installing near the ceiling of a kitchen or a boiler room as the temperature may rise to high levels Cleaning To remove dirt from the case moisten a soft cloth with a soft detergent solution and wipe Mounting Surface The material of the mounting surface must be strong enough to support the camera FCC COMPLIANCE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment This equipment generates uses and radiates radio fre2. EXIT M 8 EXIT EXIT 11 EXPOSURE EXPOSURE LENS SUCK Manual Manual mode supports the fixed board lens or the manual BACKLIGHT OFE Abe iris lens DEFOG NOTE MANUAL mode has FOCUS ADJ You can adjust the focus STARLIGHT ki finding the highest number on the FOCUS SET EXIT JUMPd MANUAL Lens Submenu MODI MODE DEBLUR BRIGHTNESS 10 SHUTTER FOCUS ADJ RETURN 12 Mode Set the lens mode to Normal or Deblur Brightness Adjust the camera s brightness from 0 20 The higher the number the brighter the image will appear Shutter Set the shutter speed to AUTO Manual or FLC Flicker less mode Select FLC if the camera is experiencing some flickering in the image If Manual is selected set the shutter speed from 1 60 to 1 60000 Focus Adjustment When on the default level is set automatical ly by controlling lens focus and based on the installation and environment circumstances oj EXPOSURE BACKLIGHT OFF HME HIGHLIGHT MASKING EXPOSURE HME allows objects to appear clearly screen by EMMET masking extremely bright areas To setup HME the LENS MANUAL level and mode The lower the setting the darker the DRC OFF DEFOG OFF 21 masking areas have to be Select from 0 20 Mode Select when to enable HME settings Select from All Day Run HME always or Night Only HME is enabled only in B W mode AGC STARLIGHT 3D DNR EXI
3. is disappeared by wall or curtain The lower the number the more sensitive the camera will be to new motion once detected MOTION MOTION DET SETTING MAARE AA a M WINDOW TONE 8 OBJ KEEP LV 6 1 W ZONE 0 MOTION EST Je W USE SIGNAL OUT ON POS RETURN ALARM 4 QUICK ZOOM OFF WINDO WINDO EXIT JUMP4 H RETURN MOTION SET Window Tone Set the size of the zone s borders Window Zone The camera supports up to 4 different motion detection zones Window Use Select which one of the motion areas to enable DET H POS Move the Zone left or right The higher the number the zone will move to the right DET V POS Move the Zone up or down The higher the number the zone will move down DET H Size Adjust the size horizontally The higher the number the right side panel will move further to the right DET V Size Reset the zone s size vertically The higher the number the bottom side panel will move further down 19 MOTION The camera can detect the movement and display an alarm on the screen when movement is detected ALARM Select to enable or disable the camera s motion detection and select which conditions will trigger the alarm from the following options Shaking ON OFF Camera Moving will appear if the camera is shaken abruptly ALARM Shaking Scale 0 20 The lower the number the more sensitive the SHAKE SCALE BRIGHT CHG ON BRIGHT SCL IIIII 3 camera w
4. 0 20 AGC enhances the picture brightness in low light conditions A higher level AGC setting makes the images brighter however it could increase the amount of noise STARLIGHT Automatically activates slow shutter function when the image is too dark OFF x2 x64 High values are not recommended as they may causes the image to lag Default X4 Starlight menu cannot be controlled if the SHUTTER setting is above 1 60 3D DNR 3D DIGITAL NOISE REDUCTION OFF LOW 3D DNR reduces the noise on the screen in low light conditions and MID HIGH allows for clearer images even at night 14 DW COLOR WB MODE ATW Auto Tracking White Balance Control mode compensates for color temperature changes between 2400K and 11000K AWB Auto White Balance Control mode compensates for color temperature changes lower than 2000K and higher than 15000K PUSH Push fixes the white balance based on the current lighting automatically MANUAL Users can control the white balance manually by changing RED GAIN and BLUE GAIN see below KELVIN Select from Low Middle or High If enabled the Red and Blue Gain settings will be set automatically according to the Kelvin settings RED GAIN 0 20 Agjusts the amount of red in the image BLUE GAIN 0 20 Adjust the amount of blue in the image COLOR WHITE BAL MANUAL4 KELVIN MIDDLE COLOR GAIN R GAIN Joe t I 110 EXIT JUMP4 B GAIN 110 RETURN COLOR GAIN Set the colo
5. OFF x2 x64 3D DNR OFF Low Middle High White Balance ATW AWB PUSH MANUAL 27 Auto Gain Control 0 20 Intelligent Motion Detection Digital Quick Zoom Motion Detection 4 Motion Regions Privacy Zones 16 Programmable Privacy Masks Enhanced Day amp Night Function LED Operation point selection External LED ON OFF Control Sharpness 0 10 Gamma 0 45 0 65 De Fog OFF ON Operating Temperature 20 C 60 C 4F 140 F Operating Humidity Less than 90 Non Condensing IP Rating IP66 Protects against dust and high pressure water Power Requirement DC12V Power Consumption LED OFF 1 6W 132mA LED ON 3 36W 255mA Dimensions 280 X 79 8 mm 3 15 X 3 14 in Weight 0 83 105 Specification is subject to change without prior notice 28 MEMO DA IGITAL Everything s Digital 5436 W Crenshaw St Tampa FL 33634 Tel 866 446 3595 813 888 9555 Fax 813 888 9262 www Digital Watchdog com technicalsupport dwcc tv Technical Support Hours Monday Friday 9 00am to 8 00pm EST
6. T JUMPd BLC BACK LIGHT COMPENSATION II BLC is selected adjust the size nad position of the mask H POS Move the Zone position left or right The higher the number the zone will move to the right V POS Move the Zone position up or down The higher the number the zone will move down H Size Reset the zone s size horizontally The higher the number the right side panel will move further to the right V Size Reset the zone s size vertically The higher the number the bottom side panel will move further down 1 IC SIZI RETURI WDR Wide Dynamic Range If WDR is selected adjust the WDR level in the submenu Select from Low Middle or High Default 13 EXPOSURE DRC DYNAMIC RANGE COMPRESSOR DRC enables dark areas in images to become more visible without overexposing the bright areas to create one perfect image Select from Off Low Middle or High NOTE If WDR or DEFOG are enabled the DRC settings are set automatically and will not be available for adjustment DEFOG Allows the camera to process a scene that is obscured by fog or weather conditions and provides a visibly improved image AUTO Manual Select AUTO to have the WDR and DRC levels adjusted automatically Set the DEFOG level from LOW MIDDLE HIGH EXPOSURE LENS MANUAL4 BACKLIGHT OFF DRC OFF DEF OC MODE AUTO LEVEL MIDDLI RETURN AGC STARLIGHT 4 3D DNR HIGH EXIT JUMP AGC AUTO GAIN CONTROL
7. e for Night Model Select to keep in color or switch to B amp W At the bottom of the screen the settings will be summarized for your review The information includes according to current settings the EXT level for Day to switch to Night EXT level for Night to switch back to Day and current EXT level for reference DAY amp NIGHT ol ma uir CONTROL AGC THRES AGC MARGII C MARGIN RETURN I 16 DW DAY amp NIGHT CONTROL CONT CDS The camera s Day Night switch will be set according to the LED board in the camera CDS Threshold Marks the light level at which the camera will switch between color and B W The lower the value the camera will require less light more darkness to switch to Night Mode IE PTA CDS Signal The value added to the CDS Threshold Adjust this value MODE COLO based on the environment in which the camera is installed EXT LED AUTO Night Mode Select what will the camera do when the light threshold is BAW BURST OFF met for Night Model Select to keep in color or switch to B amp W EXIT At the bottom of the screen the settings will be summarized for your review The information includes according to current settings the CDS CONTROL threshold for Day to switch to Night CDS threshold for Night to switch AGC THRES b back to Day and current CDS level for reference RETE EXT LED AUTO 0 AUTO Enables the IR LED board OFF disable
8. ill be to shocks or vibrations RETURN Bright Change ON OFF Birght Change will appear if the brighness in the scene changes suddenly and drstically Bright Scale 0 20 The lower the number the more sensitive the camera is to brightness changes in the scene QUICK ZOOM The camera can automatically digitally Zoom in when motion is detected ae In the submenu setup the following MOVING Set the camera s movement speed 30 60 0 5 Second is the default TRACKING OFF speed Max speed 240 60 4 Seconds RETURN ZOOM IN Set the camera s zooming speed 240 60 4 Seconds is the default speed Max speed 240 60 4 Seconds TRACKING The camera keeps tracking the moving area and operates Zoom In Out REPEAT The camera will continue to zoom into motion as it detects it in different parts of the camera s view 20 DW PRIVACY You can hide some parts of the screen for privacy masking A total of 8 different privacy masking zones are available PRIVACY SET Select the zone number you want to setup To enable it turn the display option ON ZONE NUM H POS Move the Zone position Left or right The higher the t4 number the zone will move to the right 2 V POS Move the Zone position up down The higher the number the zone will move down H Size Reset the zone s size horizontally The higher the number the right side panel will move further to the right V Si
9. option at no charge PARTS In addition the Warrantor will supply replacement parts for the initial five 5 years and one 1 year on IR LED To obtain warranty or out of warranty service please contact a Technical Support Representative at 1 866 446 3595 Monday through Friday from 9 00AM to 8 00PM Eastern Standard Time A purchase receipt or other proof of the original purchase date is required before warranty service is rendered This warranty only covers failures due to defects in materials and workmanship which arise during normal use This warranty does not cover damage which occurs in shipment or failures which are caused by products not supplied by the Warrantor or failures which result from accident misuse abuse neglect mishandling misapplication alteration modification faulty installation set up adjustments improper antenna inadequate signal pickup maladjustment of consumer controls improper operation power line surge improper voltage supply lightning damage rental use of the product or service by anyone other than an authorized repair facility or damage that is attributable to acts of God 25 LIMITS 8 EXCLUSIONS There are no express warranties except as listed The warrantor will not be liable for incidental or consequential damages including damage to recording media without limitation resulting from the use of these products or arising out of any breach of the warranty All express and implied warranties incl
10. quency energy and if it is not installed and used in accordance with the instruction manual it may cause harmful interference to radio communications WARNING Changes or modifications are not expressly approved by the manufacturer ABLE OF CONTENTS Introduction Features 2 _ __ ee ee 4 Parts and Descriptions _____ _ _ _ _ _ ______ 5 Dimensions asa i a RE 6 Installation _______ _ Inside the BOX um ee aw iwa 7 Mount Installation Instructions 8 Connecting to Monitors __ __ 9 Control Board s uus eus 2 2 edm 10 Module OSD Menu 11 22 Troubleshooting 23 Warranty Information Le 24 25 gt 26 27 FEATURES 1 3 Sony 1 3MP CMOS 820TVL B W 800TVL Color QuickZoom Full Frame 8x Digital Zoom with no Loss in Resolution Star Light Super Low Light Technology Wide Dynamic Range WDR 3 6mm Fixed Lens Smart IR with Intelligent Camera Sync 50ft Range 3D Digital Noise Reduction DNR Highlight Masking Exposure HME De Fog Extreme Weather Image Compensation Secondary Video BNC Output True Day Night Mechanical IR Cut Filter Programmable Privacy Zones Auto Gain Control AGC Back Light Compensation BLC Dynamic Range Compressor DRC Reveals Low Light Detail Auto White Balance AWB IP66 Certified Weather Resistant PARTS 8 DESCRIPTION Ball Cover Gap Sponge Ball Base Set Sc
11. r gain from 0 20 15 A DAY 8 NIGHT D amp N E AUTO In AUTO mode the camera switches between day and night automatically depending COLOR light level If COLOR is selected the camera always stays in day color mode B amp W B amp W is selected camera always stays in night B amp W mode CONTROL Select if the Day Night switch will be based on the AGC levels AUTO or using IR LED lights EXT AUTO if selected Day Night switch will depend on the AGC levels e perl AGC Threshold Set when the camera switches between Day amp Night ry PESE Ue AGC Margin Set the value added to the AGC Threshold Adjust the E EE value based on the environment in which the camera is installed Night Mode Select what will the camera do when light threshold is met for Night Mode Select to keep in color or switch to B amp W At the bottom of the screen the settings will be summarized for your review The information includes according to current settings the AGC threshold for Day to switch to Night AGC threshold for Night to switch back to Day and current AGC level for reference if selected adjust the external signal to CDS or LOW HIGH Low High The camera s Day Night switch will be set according to an external LED board Set to HIGH to make the camera switch to night mode only when there is very little light Night Mode Select what will the camera do when light threshold is met for Night Mod
12. r that you use from RED and PASS then reboot the camera to use RETURN INITIAL Reset the camera to its factory default settings To do so press and hold the select button for five 5 seconds 22 BB EXIT Exit the OSD menu after saving recent changes INITIAL Exit the OSD menu after resetting the camera to factory default XIT SAVEREXITd EXIT EXIT4 MODE 5 60Hz MODE NTSC 60Hz 23 ROUBLESHOOTING Before sending your camera for repair check the following or contact our technical specialist FOR NO VIDEO Check the coaxial cable and make sure it is connected securely Check the lens iris adjustment at the camera s OSD menu Check the power supply and make sure the camera has the proper voltage and current FOR OUT OF FOCUS VIDEO Check the clear dome cover and the lens for dirt or fingerprints Use a soft cloth and gently clean Check the lens manual focal and zoom adjustment The use of a field test monitor is recommended 24 DW WARRANTY INFORMATION Digital Watchdog referred to as the Warrantor warrants the Digital Watchdog Camera against defects in materials or workmanship as follows LABOR For the initial five 5 years and one 1 year on IR LED from the original purchase date if the camera is determined to be defective the Warrantor will repair or replace the unit with a new or refurbished product at its
13. rew 69 Camera s Lens Ball Camera Module OSD Plug DIMENSIONS IN MILLIMETERS IN 46 0 1 81 INSIDE THE BOX Included with Ball Camera User Manual 69 Mounting Template 4 Machine Screws and 4 Dry Wall Anchors Secondary Video BNC Cable External OSD Controller Mounting template INSTALLATION INSTRUCTIONS 1 To disassmble the camera uncrew the small screw at the base of the camera s housing The ball with the camera module will get loose and separate from the ball housing 2 Use the camera or mounting template to mark and drill the necessary holes in the wall or ceiling 3 Pull wires through and make connections gt 4 Using the four 4 included screws mount and secure the camera to the wall or ceiling 5 Use the joystick to adjust the OSD menu See pages 11 22 for more information 6 Secure the camera s ball module into the housing using the small screw at the base of the camera s housing CONNECTING TO MONITORS Use the diagram below to connect to a Monitor or CRT Monitor properly 12VDC Monitor Power Connection 12VDC All cameras are equipped with a second video output for on site configuration The Ball camera includes an exte
14. rnal OSD Joystick to control the camera s OSD setup menu Unscrew the protecting cover at the top of the camera s ball module Connect the included external OSD Joystick Controller Use the Joystick to control the camera s OSD options MODULE OSD MENU EXPOSURE LENS MANUAL BACKLIGHT OFF HME BLC WDR DRC OFF LOW MIDDLE HIGH DEFOG OFF ON AGC 0 20 STARLIGHT OFF x2 x64 3D DNR OFF LOW MIDDLE HIGH EXIT JUMP SAVE 8 EXIT EXIT MOTION MOTION OFF ON ALARM SHAKING OFF ON SHAKE SCALE 0 20 BRIGHT CHG OFF ON BRIGHT SCL 0 20 QUICK ZOOM OFF ON EXIT JUMP SAVE 8 EXIT EXIT COLOR WB BAL ATW AWB PUSH MANUAL COLOR GAIN EXIT JUMP SAVE EXIT EXIT PRIVACY ZONE NUM 0 15 ZONE DISP OFF ON CB LEVEL 0 20 EXIT JUMP SAVE 8 EXIT EXIT DAY amp NIGHT D amp N MODE AUTO COLOR B amp W CONTROL AUTO EXT EXT LED AUTO OFF DELAY LOW MIDDLE HIGH B amp W BURST 0 EXIT JUMP SAVE amp EXIT EXIT SETUP COMMUNICA CAM ID 0 255 BAUDRATE 2400 4800 9600 57600 115200 VIEW ANGLE NORMAL 4 3 16 9 LANGUAGE ENGLISH CHINESE CHINESE S JAPANESE KOREAN SPECIAL DEFECT DET TV MODE O L P F INITIAL EXIT JUMP SAVE amp EXIT EXIT DW FUNCTION SHARPNESS GAMMA 0 45 0 65 MIRROR x1 0 x8 0 EXIT JUMP SAVE amp EXIT EXIT
15. the camera s LEDs DELAY Low Mid High Time interval delay before switching from day mode to night mode B amp W BURST ON OFF If ON is selected the camera provides a color burst signal in night mode SMART IR 0 20 Enable Smart IR and set the level Higher values will make Smart IR stronger 17 FUNCTION SHARPNESS 0 10 Sets the image sharpness The higher the number the sharper the image GAMMA 0 45 0 65 Select the desired gamma level 0 55 is default setting MIRROR FLIP OFF MIRROR Reflects the camera horizontally FLIP Reflects the camera vertically SHARPNESS 7 Pe 62 Mirror Flip OFF Mirror ON Flip ON Mirror amp Flip ON D Zoom 1 0x 8 0 Enable or Disable Digital zoom to the camera s field of view By default the zoom will go to the center of the camera s Field of View 18 DW MOTION The camera can detect the movement and display an alarm on the screen when movement is detected MOTION OFF ON Select to enable or disable the camera s motion detection If ON is selected DET SETTINGS Use this submenu to adjust the motion detection s sensitivity detection dwell time Motion Estimate and setup a Signal Output Action Sensitivity The smaller the movement you want to detect the higher the sensitivity value must be Object Keep LV Set the dwell time for how long motion is detected Motion Estimate Predicts possible direction once motion
16. uding the warranties of merchantability and fitness for particular purpose are limited to the applicable warranty period set forth above Some states do not allow the exclusion or limitation of incidental or consequential damages or limitatons on how long an implied warranty lasts so the exclusions or limitations listed above may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state If the problem is not handled to your satisfaction then write to the following address Digital Watchdog Inc ATTN RMA Department 5436 W Crenshaw Street Tampa FL 33634 Service calls which do not involve defective materials or workmanship as determined by the Warrantor in its sole discretion are not covered Costs of such service calls are the responsibility of the purchaser 26 SPECIFICATIONS Image Sensor 1 3 Sony 1 3 Mega Pixel CMOS Sensor Active Pixels 1280 H x 1024 V Scanning System 2 1 Interlace Frequency 15 734KHz 59 95Hz V Synchronization Internal Horizontal Resolution Minimum Illumination 820 TV Lines B W 800 TV Lines Color 0 14Lux F1 2 SOIRE at Color 0 03Lux F1 2 at TDN B W S N Ratio Video Output Focal Length 5598 AGC off CVBS 1 0Vp p 750 3 6mm Fixed Lens IR Distance 508 Range IR Shutter Speed 50 60 60 000s Backlight OFF HME BLC WDR Star Light Sense Up
17. ze Reset the zone s size vertically The higher the number the bottom side panel will move further down MASK COLOR To adjust the mask s color use the Y CR and CB Levels Y Level The higher the number the brighter the color will appear Level The higher the number the more red tone will be added to the zone s color The lower the number the more green will be added to the zone s color Level High CB Level High CR Level Red High CB Level Low CR Level Blue Low CB Level High CR Level Orange 21 0 SETUP COMMUNICATION Use this setup menu to adjust the camera s ID and Baudrate A II The camera s default Protocol is Pelco D COMMUNICA CAM ID Provide an ID number for the camera 0 255 LANGUAGI BAUDRATE 9600bps is default Select the baudrate from the EXIT JUWP following options 2400 4800 9600 57600 115200 bps VIEW ANGLE 4 3 16 9 Adjust the camera s aspect ratio By default the camera is set to NORMAL 4 3 If applicable set it to 16 9 LANGUAGE The Camera supports the following languages English Default Chinese Chinese S Japanese and Koran SPECIAL SPECTA DEFECT DET The camera can detect and correct dead pixels in the DEFECT DET image To do so press the select button and set the threshold level r RED The camera will detect and adjust the pixels automatically TV MODE Set the camera to NTSC Default or PAL OLPF Select the filte
Download Pdf Manuals
Related Search