Home

CPD517, 515, 511 quick_V0.93 Please read instructions

1. The cameras must be connected and power supplied before the DVR is turned on Connect the camera with the indicated power supply And then connect the camera video output to the DVR video input port with a coaxial cable or RCA lines with BNC connectors The DVR will automatically detect the video system of the camera Note For detailed DVR video input output ports please refer to 2 2 Rear Panel at page 2 For detailed camera operation please refer to its own manual Note If you want to make a video backup with audio please connect audio cameras to the channels which support the audio function For 16CH amp 8CH DVR the audio channels are CH1 CH2 CH3 and CH4 For 4CH DVR the audio channel is CH1 3 3 Power Setup This device should be operated only with the type of power source indicated on the manufacturer s label Connect the indicated AC power cord to the power adapter and plug into an electrical outlet Power LED D gt will be on as blue lt takes approximately 10 to 15 seconds to boot the system 3 4 Date and Time Setting Before operating your DVR please set the date and time on your DVR first Press MENU button and enter the password to go to the quick start menu list The default admin password is 0000 Move the cursor to the icon and you can set the date time daylight saving in this menu list CHANNEL TITLE EVENT STATUS IMAGE SIZE QUALITY IMAGE PER SECOND RECORD TIMER DETECTION TIMER DATE FOR
2. 263Z EVOLUTION CAM For Your Demand MPEG 4 DVR QUICK Please read instructions thoroughly before operation and retain it for future reference The image shown above may differ from the actual product appearance CPD517 515 511 quick V0 93 Ll iii tttltctctttttcctttttttttti 1 1 Package Contents Digital video recorder DVR 1 HDD bracket screws spare parts 4 Adapter and power cord 1 DSUB PIN connector 1 Free licensed software AP disc 1 IR remote controller 1 Manual amp quick start amp IR remote control manual 1 AAA size battery 2 Note Before using the IR remote controller please install the batteries first 1 2 Front Panel 1 2 LED Indication The following LEDs will be on when Q POWER power is connected HDD HDD is reading or recording HDD Full HDD is full Je ALARM any event alarm is triggered TIME timer recording is activated gt PLAY when the DVR is playback STANDBY when the DVR is standby HDD Full HDD is full REC when the DVR is recording USB port To quickly backup or upgrade firmware OSD you can insert a compatible USB flash drive into this USB port Before using the USB flash drive please use your PC to format the USB flash drive as FAT32 first Note For the list of compatible USB flash drives please refer to APPENDIX 2 COMPATIBLE USB FLASH 3 DRIVE BRAND in the user manual IR receiving zone lf
3. the control panel is removed from the DVR and used as a remote controller aim the remote controller at this area to control the DVR operation Password Entering Use the number buttons to enter the DVR password Or use buttons to setup the password Channel Display Selection Use the number buttons select the channel Or press SHIFT CH and SHIFT CH buttons to select the channel SNAP When the DVR is not under the menu mode connect a USB drive to the DVR and then press SNAP button to take a snapshot picture of the current live image on the monitor LIST Event List Search To quick search the recorded files by event list press LIST button or SHIFT LIST buttons to show all types of the event lists ALARM List the information of the alarm trigger recorded files MANUAL List the information of the manual recorded files The DVR will save one recorded file once any recording setting is changed e MOTION List the information of the motion trigger recorded files SYSTEM List the information of the system recorded files The DVR system will save one recorded file every one hour TIMER List the information of the timer recorded files 13 14 PLAY Press this button to playback the recorded video MENU Press this button to enter exit the quick start menu In the sub layer of the advanced setting menu press this button to confirm the settings and go back to the upper lay
4. 3 seconds 8192 images 30 IPS for the playback to work properly 1 Fast Forward gt gt Fast Rewind lt lt You can increase the speed for fast forward and rewind on this device In the playback mode Press gt once to get 4X speed forward and press twice to get 8X speed etc And the maximum speed Is 32X Press lt 4 lt once to get 4X speed rewind and press twice to get 8X speed etc And the maximum speed is 32X Note During playback the image size of the recording Frame Field or CIF will be shown on the screen 2 Pause ii Image Jo Press PAUSE or IF button to pause the playback In the Pause mode Press gt button once to get one frame forward Press lt lt button once to get one frame rewind 3 Stop E Press STOP or W button under playback mode the screen of this device will return to live monitoring mode 4 Slow Playback Press SLOW button to get 1 4X speed playback and press twice to get 1 8X speed playback 5 Audio Playback Press SLOW ZOOM buttons or SHIFT AUDIO buttons to select the live or playback sound of the audio channels ih Icon xip means Live audio of the 1 audio channel Icon J Icon Ki 4 i means Live audio of the 3 audio channel Icon means Playback audio of the 1 audio channel a means Live audio of the 2 audio channel Icon Q means Playback a
5. MAT DAYLIGHT SAVING v ADVANCE f SELECT BACK ON ON CIF BEST 120 OFF OFF 2007 AUG 08 21 30 00 Y M D OFF gt NEXT ENTER Note If the time and date settings return to their default value after the DVR is rebooted please charge the DVR for at least 24 48 straight hours Please contact your local retailer if the situation still Occurs 3 5 Password Setting Press MENU button and enter the password to go to the quick start menu list And then move the cursor to ADVANCE to enter the advanced setting menu In the ADVANCE menu move the cursor to SYSTEM INFO Select PASSWORD and press ENTER button to enter the submenu to set the password four digits The default admin password is 0000 SERIAL TYPE BAUD RATE HOST ID PASSWORD RESET DEFAULT CLEAR HDD UPGRADE AUTO KEYLOCK SEC LANGUAGE VIDEO FORMAT VERSION RS485 2400 0 XXXX RESET HDD MASTER 1 START 30 ENGLISH NTSC 1049 1007 1011 1001 L6 6C1B PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTINGS ty SELECT BACK gt NEXT ENTER 4 BASIC OPERATION Take 16CH DVR as an example 4 1 Live Page In this live page of the DVR you can see the live viewing of 1 4 9 16 cut screen Key lock Audio Channel System time Digital Zoom Timer Recoding gioa Yi a E TAA a Motion w to Channel title Recording 1 live audio 2nd live audio Key lock Key unlock Digital zoom imer rec
6. er ENTER Confirm the password entering Under the advanced menu use this button to confirm the settings and go back to the upper layer EJECT M Press this button to open close the DVD RW drive SLOW Under the playback mode press SLOW button or SHIFT SLOW buttons to slowly playback the recorded file by 1 4 speed or 1 8 speed ZOOM Press this button to enlarge the image of the selected channel AUDIO Press SLOW ZOOM buttons or SHIFT AUDIO buttons to select the live or playback sound of the audio channels 4 Icon Icon Ghi means Live audio of the 2 audio channel Icon 4 W means Live audio of the 1 audio channel Icon means Playback audio of the 1 audio channel means Playback audio of the 2 audio channel Icon means Live audio of the 3 audio channel Icon means Playback audio of the 3 audio channel Icon Hh means Live audio of the 4 audio channel Icon 2 means Playback audio of the 4 audio channel Icon amp means The audio channel is not selected Note If you want to make a video backup with audio please connect audio cameras to the channels 15 16 17 which support the audio function For 16CH amp 8CH DVR the audio channels are CH1 CH2 CH3 and CH4 SEQ Sequence Press SEQ button or SHIFT SEQ buttons the DVR will enter full screen se
7. erwise switch to 75Q Note The default setting is 75Q 2 LOOP INPUT 1 16CH or 1 8CH LOOP Video output connector INPUT Connect to video sources such as cameras Note The DVR will automatically detect the video system of the camera please make sure that the cameras are properly connected to the DVR and power supplied before the DVR is turned on Note If you want to make a video backup with audio please connect audio cameras to the channels which support the audio function For 16CH amp 8CH DVR the audio channels are CH1 CH2 CH3 and CH4 3 MONITOR Connect to a CRT monitor for video output 4 5 10 11 12 CONNECTIONS AND SETUP CALL Connect to CALL monitor to show the channel display one by one When any alarm is triggered CALL monitor will show the image of the triggered channel for a period of time Audio IN 1 2 3 4 Connect to audio sources such as cameras equipped with the audio function When users start recording the audio input will also be recorded with corresponding video channel The audio source connected to the Audio 1 will be recorded with the video of the CH1 The audio source connected to the Audio 2 will be recorded with the video of the CH2 The audio source connected to the Audio 3 will be recorded with the video of the CH3 The audio source connected to the Audio 4 will be recorded with the video of the CH4 Note If you
8. ording unselected Alarm 4 2 Recording a 3 live audio 4 live audio Audio channel E Ma A O aea R Dotai zoom mose a When the recording and the pre alarm function are activated this device will overwrite 8GB data from the oldest for continuous recording without notice 1 Continuous Recording Icon When the DVR is properly connected with camera you can see the icon recording on the screen 2 Event Recording Icon When the motion alarm detection is activated once motion or external alarm happens you will see the icon Eb motion or 8 external alarm on the screen 3 Timer Recording Icon When the timer record is activated you will see the icon timer on the screen Note The audio source connected to the Audio 1 will be recorded with the video of the CH1 The audio source connected to the Audio 2 will be recorded with the video of the CH2 The audio source connected to the Audio 3 will be recorded with the video of the CH3 The audio source connected to the Audio 4 will be recorded with the video of the CH4 4 3 Playback Press the PLAY button on the DVR control panel and the device will playback the latest recorded video Note There must be at least 8192 images of recorded data for playback to work properly If not the device will stop playback For example if the IPS is set to 30 the recording time should be at least 27
9. quence mode Press again to exit the sequence mode HA 16CH Press this button to show the 4 9 16 channel display modes 8CH Press this button to show the 4 9 channel display modes PTZ Press SEQ EX buttons or lt lt gt gt buttons at the same time to enter exit the PTZ control mode In the PTZ control mode Indicated by the icon AW Dn Zoom in Press button Zoom out Press button Adjust PTZ angle Press UP DOWN LEFT or RIGHT buttons CONNECTIONS AND SETUP 18 BE PAUSE UP lt lt REW LEFT gt gt FF RIGHT 3 TOP DOWN Press one of these direction buttons to move the cursor up down left right Under the DVR menu mode these direction buttons can use for the following operation A VY Make the selection Change the settings lt gt Go to the upper layer or sub layer Make the selection Under the playback mode press these buttons to pause stop fast rewind fast forward the playback file 2 2 Rear Panel 16CH LINK O ACT 8CH hiatal 4CH AUDIO LINK ACT EXTERNAL I O LAN 1 750 HI IMPEDANCE When using LOOP function set the impedance switch at your DVR rear panel to HI IMPEDANCE to decrease interferences Oth
10. udio of the 2 audio channel Icon means Playback audio of the 3 audio channel Gh Icon means Live audio of the 4 audio channel Icon i means Playback audio of the 4 audio channel Icon Q means The audio channel is not selected Note If you want to make a video backup with audio please connect audio cameras to the channels which support the audio function For 16CH amp 8CH DVR the audio channels are CH1 CH2 CH3 and CH4 For 4CH DVR the audio channel is CH1 4 4 Key Lock and Unlock 1 Key Lock On Press MENU ENTER buttons on the DVR control panel to lock keys Or set the time out after which the key lock function is activated Never 10 SEC 30 SEC 60 SEC 2 Key Lock Off Enter the DVR password to exit Key Lock mode Note For the password setting please refer to the section 3 5 Password Setting at page 5 INDEX 4 5 Upgrade Firmware Multilanguage OSD Upgrade 1 Use USB to upgrade firmware or OSD Step 1 Format the USB memory device as FAT32 format first Step 2 Get the upgrade files from your distributor and save the upgrade files in your USB flash device do not change the file name 4 Step 3 In the Zal SYSTEM INFO menu move the cursor to UPGRADE and press ENTER button Step 4 Select YES and press ENTER button again to confirm upgrade 2 Use AP software to remotely upgrade firmware or OSD Step 1 Save the
11. upgrade files at your PC do not change the file name and then login to the AP software Step 2 Press Ep Miscellaneous Control button to show the miscellaneous control panel In the miscellaneous control panel press Ei Tools button on the miscellaneous control panel to enter the AP upgrade window Step 3 Enter the user name password IP address and port number of the DVR Step 4 Press Firmware or Language tab as needed and press Add to select the firmware or OSD files to upgrade Step 5 Press Update Firmware or Update Language button to start the upgrade 4 6 Search 1 Search by List Press LIST button on the DVR control panel to show the list for all types of the recorded files Choose the list you want to view and press ENTER button to start playback ALARM List the information of the alarm trigger recorded files MANUAL List the information of the manual recorded files The DVR will save one recorded file once any recording setting is changed MOTION List the information of the motion trigger recorded files SYSTEM List the information of the system recorded files The DVR system will save one recorded file every one hour TIMER List the information of the timer recorded files 2 Search by Time In the T EVENT LOG menu list move the cursor to QUICK SEARCH and press ENTER button to enter the quick search menu You can search any specific events by time Year Month Day Hour Min and directl
12. want to make a video backup with audio please connect audio cameras to the channels which support the audio function For 16CH amp 8CH DVR the audio channels are CH1 CH2 CH3 and CH4 For 4CH DVR the audio channel is CH1 Audio OUT Connect to a monitor or speaker with 1 mono audio output IR Connect the IR receiver extension line for remote control EXTERNAL I O Insert the supplied 25PIN DSUB to this port for connecting external devices external alarm etc For detailed I O port PIN configuration please refer to APPENDIX 1 PIN CONFIGURATION LAN Connect to Internet by LAN cable LINK ACT When your DVR is connected to the Internet this LED will be on DC 19V Connect to the supplied adapter Fan 3 CONNECTIONS AND SETUP Take 16CH DVR as an example 3 1 HDD Installation The HDDs must be installed before the DVR is turned on Step 1 Loose the screws on the upper cover and open the upper cover of the DVR Step 2 Screw out the HDD bracket Step 3 Get a suitable brand HDD and set the HDD mode Master Step 4 Align the screw holes of the bracket with the HDD s screw holes Screw the HDD onto the HDD bracket Step 5 Screw the HDD bracket back to the DVR base Step 6 Connect the HDD to the power connector and IDE BUS make sure to align the HDD precisely for pin connection Step 7 Close the upper cover of the DVR and fasten all the screws you loosened in Step 1 3 2 Camera Connection
13. y play the file you find 3 Search the Record Event by Log on the AP Software Press EL Miscellaneous Control button to show the miscellaneous control panel In the miscellaneous control panel press Ce Log button to enter the Log View page In this log view page you can see the list of three different types of recording User Motion Alarm and press Play button to directly playback the file

CPD517, 515, 511 quick_V0.93 Please read instructions

Contents

Download Pdf Manuals

Related Search

Related Contents