Home

ACTinBOX CLASSIC HYBRID AD

1. When Outputs is set to Yes a new tab will be added to the left side panel making it possible to configure the outputs of the device This screen will look as follows lt lt DUTPUTS gt gt GENERAL DUTPUTS lt lt THERMOSTAT gt gt Channel A Disabled y Channel B Disabled z Figure 5 Configuring the outputs The outputs are grouped into channels Channel A and Channel B both disabled by default with two outputs each A drop down list permits configuring the behaviour of each channel as individual outputs or shutter channels GENERAL lt lt DUTPUTS gt gt BE OCH E lt lt THERMOSTAT gt gt Channel A Disabled D Disabled Shutter Channel Figure 6 Configuring the channels 3 2 1 INDIVIDUAL OUTPUTS Figure 7 represents an example of how a channel can be parameterized in this case channel A is parameterized as individual outputs output 1 and 2 GENERAL OUTPUT 1 lt lt DUTPUTS gt gt DUTPUT 2 lt lt THERMOSTAT gt gt TYPE Normally Open y FUNCTIONS Timers No Scenes No X Alarm No Z BUSY Deet BUS volt recovery configuration Default Figure 7 Channel A configured as individual outputs http www zennio com Technical Support http zennioenglish zendesk com 12 Zennio ACTinBOX CLASSIC HYBRID AD Once the output is enabled the ETS topology will automatically display the fo
2. both shown after this option is chosen gt Update by enabling this field Yes the position status object will be sent to the bus as a feedback for the rest of the devices in the installation In addition a delay can be applied to this sending If the value O is set the status is sent immediately Note the initial status is always sent through the object CX Current Shutter position and CX Current Slats position for slats Note in the event of a bus power failure while the shutter is moving ACTinBOX Classic Hybrid opens the output relay prior to being unpowered as a security measure The interrupted movement is not resumed after the bus recovery 3 3 INPUTS If Inputs is set to Yes a new tab will appear in the menu on the left side http www zennio com Technical Support http zennioenglish zendesk com 33 Zennio ACTinBOX CLASSIC HYBRID AD GENERAL lt lt INPUTS gt gt lt lt THERMOSTAT gt gt ger SSC INPUT 2 Disabled S NPUT 3 Disabled X INPUT 4 Disabled D INPUT 5 Disabled e INPUT 6 Disabled z Figure 20 Inputs configuration Inputs can be configured as push button switch sensor temperature probe only input 5 and movement detector only input 6 All these options are explained in detail in the following sections 3 3 1 PUSH BUTTON GENERAL INPUT 1 Push Butto
3. 8 Further presses will make the described sequence start again Note the ast three options require defining the dimming step to be applied Le how much the brightness level will be increased or decreased by the Dimmer after every press Please refer to Table 2 for the configurable steps Note dimmers typically perform step dimming progressively being it possible to interrupt the process as soon as a stop order arrives Therefore it is advisable to parameterize a step of 100 so a sole initial press and a later stop press are enough to set the amount of light at the desired level 1 100 1 2 50 2 3 25 4 4 12 5 8 5 6 25 16 6 3 1 32 7 1 5 64 Table 2 Dimming step gt Sending of a Scene This function allows sending the KNX bus a 1 byte scene control order The Response field is provided to select the action to be carried out on short presses e Run Scene the Ix Short press Run scene 1 byte object is enabled and will send the bus after a short press a value between 1 and 64 parameterizable for the execution of a scene http www zennio com Technical Support http zennioenglish zendesk com 37 Zennio ACTinBOX CLASSIC HYBRID AD e Save Scene the Ix Short press Save scene 1 byte object is enabled and will send after a short press the bus a scene save order so it can be executed afterwards d Long press it allows sel
4. FUNCTIONS Status Object Precise Control Scenes Alarms Reverse Movement Direct Positioning Startup TYPE TIMES Main Time Shutter Length x 0 1 sec Secondary Time Slats Length x 0 1 sec Slats Step Time x 0 1 sec Security Time Pause to change the movement direction x 0 1 sec Are total Time UP and DOWN different Additional Time when shutter gets the limit on Top or at the Bottom BLIND SPECIFIC Maintain Slats Position when shutter completes mation Slats Position at Bottom Pos FUNCTIONS Status Object Precise Control Scenes Alarms Reverse Movement Direct Positioning Startup CHANNEL A Shutter No slats CHANNEL B Figure 13 Channel A configured as a shutter no slats Blind With slats Z 150 20 OA Eb Eb Eb No 4 No 4 Yes 100 Figure 14 Channel B configured as a blind with slats http www zennio com Technical Support http zennioenglish zendesk com 23 Zennio ACTinBOX CLASSIC HYBRID AD d Times this section allows setting the times in tenths of seconds that define to the shutter movement gt Main time Shutter length this is the time the shutter needs to move all the way down or up In case the shutter does not tak
5. inserting it into the corresponding slot d Inputs 5 the remaining screw terminal block bundled with the original packaging must be plugged here to allow the connection of the inputs to the actuator To ensure the adequate behaviour the two terminals of the input devices push button switch sensor temperature probe or movement detector must be connected on the one hand to the corresponding input connection points 1 to 6 in the terminal block and on the other hand to the point identified as C on the terminal block To get detailed information about the technical features of ACTinBOX Classic Hybrid as well as on security and on the installation procedure please refer to the actuator Datasheet bundled with the original package of the device and also available at http www zennio com 2 CONFIGURATION 2 1 INDIVIDUAL OUTPUTS ACTinBOX Classic Hybrid incorporates 4 relay outputs that allow controlling different loads autonomously Each output can be enabled or disabled independently and perform different functionalities Every individual output can be configured as normally open the activation of the output makes the relay close or normally closed the deactivation of the output makes the relay open Besides the output type ACTinBOX Classic Hybrid allows the configuration of the following functionalities for the individual outputs d Timers Permits a timed control over the outputs being possible to set
6. 28 Zennio ACTinBOX CLASSIC HYBRID AD It is important to keep in mind that Alarm 1 has a higher priority than Alarm 2 This means that if a channel is under the Alarm 2 status and Alarm 1 occurs then the shutter will switch to the Alarm 1 status and only switch back to the Alarm 2 status once Alarm 1 finishes Analogously when the channel is under the Alarm 1 status and Alarm 2 occurs Alarm 1 prevails gt Trigger value sets the value 1 or 0 that will trigger the alarm status This value is intended to be received through object CX Alarm or CX Alarm2 gt Cyclical monitoring period minutes defines for the case of having a periodically sent alarm object 1 or 0 as corresponding each time the maximum permitted time without receiving the no alarm value OX Alarm value contrary to the parameterized trigger value before the actuator automatically assumes the alarm status foreseeing the possibility of a failure in the transmitting device If for whatever reason the monitoring period expires ACTINBOX Classic Hybrid will trigger the parameterized action unless it does not imply a change in the output status This will not happen while the no alarm value keeps being sent before each monitoring period expires The cyclical monitoring can be disabled by simply setting a O under this filed The following example illustrates the above behaviour Example Suppose t
7. Are total Time UP and DOWN different Yes ll Total Time Up x 0 18 Time Down is 200 z the param named above as Main Time x Additional Time when shutter gets the limit on Top or at the Bottom Time added x 0 1s 20 The following parameters add functionality or special features to both shutter types with or without slats d Status object this function provides a 1 byte communication object CX Current Shutter Position which will show at any time the exact position of the shutter in percentage This object throws the value O or 0 when the shutter in completely up and 255 or 100 when it is completely down The remaining values represent intermediate positions It is possible to set by parameter whether the shutter position will be sent every second or not This is done by enabling or disabling Send current http www zennio com Technical Support http zennioenglish zendesk com 25 Zennio ACTinBOX CLASSIC HYBRID AD shutter position every second while moving which appears once the Status Object parameter has been enabled For Blinds with slats the 1 byte object CX Current Slats Position is also provided It will show the value 0 0 when the slats are completely up and the value 255 100 when the slats are completely down 2 Precise control this function makes it possible to actually move the shutter to any position via a 1 byte communication ob
8. Direct Positioning 2 1 Go to Position 0 No Action 50 1 Bit C W 1 17 DPT_Trigger 0 1 0 Last CB Direct Positioning 1 Go to Position 0 No Action 51 1 Bit C W 1 17 DPT_Trigger 0 1 0 Last CB Direct Positioning 2 1 Go to Position 0 No Action 52 1 Bit C W 1 17 DPT_Trigger 0 1 0 Last CA Save Position 1 Save Position 0 No Action 53 1 Bit C W 1 17 DPT_Trigger 0 1 0 Last CA Save Position 2 1 Save Position 0 No Action 54 1 Bit C W 1 17 DPT_Trigger 0 1 0 Last CB Save Position 1 Save Position 0 No Action 55 1 Bit C W 1 17 DPT_Trigger 0 1 0 Last CB Save Position 2 1 Save Position 0 No Action 56 1 Byte o CTR 5 001 DPT_Scaling 0 255 0 Parameteriz CA Current Slats Position 0 0 Open 255 100 Closed 57 1 Byte o CTR 5 001 DPT_Scaling 0 255 0 Parameteriz CB Current Slats Position 0 0 Open 255 100 Closed 58 1 Byte C W 5 001 DPT_Scaling 0 255 0 Parameteriz CA Slats Positioning 0 0 Open 255 100 Closed 59 1 Byte C W 5 001 DPT_Scaling 0 255 0 Parameteriz CB Slats Positioning 0 0 Open 255 100 Closed 60 65 1 Bit C W 1 003 DPT_Enable 0 1 0 Last lx Block 1 Input Disabled 0 Input Free 65 1 Bit C W 1 003 DPT_Enable 0 1 0 Last lx Block 1 Input Disabled 0 Input Free 1 Bit O CTRW 1 001 DPT_Switch 0 1 Parameteriz Last lx Sensor Edge Edge gt Sending of 0 or 1 1 Bit JO CTRW 1 001 DPT_Switch 0 1 0 Last lx Short Press 0 Short Pr gt Sending of 0 1 Bit JO CTRW 1 0
9. Switching 0 1 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last lx Short Press Brighter Sh Pr gt Bright Sh Pr gt Stop 72 77 4Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last lx Short Press Darker Sh Pr gt Dark Sh Pr gt Stop 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last lx Short Press Brighter Darker Sh Pr gt Bright Dark Sh Pr gt Stop 1 Byte o CTR 18 1 DPT_SceneControl 0 63 128 191 0 Last lx Short Press Run Scene Short Pr gt Sending of 0 63 SB 1 Byte o CTR 18 1 DPT_SceneControl 0 63 128 191 0 Last lx Short Press Save Scene Short Pr gt Send of 128 191 1 Bit O CTRW 1 001 DPT_Switch 0 1 0 Last lx Long Press Dimmer On Long Pr gt Sending of 1 ON 1 Bit O CTRW 1 001 DPT_Switch 0 1 0 Last lx Long Press Dimmer Off Long Pr gt Send of 0 Off 1 Bit O CTRW 1 001 DPT_Switch 0 1 0 Last lx Long Press Dimmer On Off Long Pr gt Switching 0 1 1 Bit O CTRW 1 007 DPT_UpDown 0 1 0 Last lx Long Press Move Up Shutter Long Pr gt Sending of 0 Up 1 Bit O CTRW 1 007 DPT_UpDown 0 1 0 Last Ix Long Press Move Down Shutter Long Pr gt Send of 1 Down 1 Bit O CTRW 1 007 DPT_UpDown 0 1 0 Last lx Long Press Move Up Down Shutter Long Pr gt Switching 0 1 A 1 Bit JO CTRW 1 7 DPT_Step 0 1 0 Last lx Long Press Stop Step Up Shutter Long Pr gt Sending of 0 1 Bit O CTRW 1 7 DPT_Step 0 1 0 Last lx Long Press Stop Ste
10. respectively assuming that the blind is stopped These step orders allow gradually rotating the slats and modifying their position which may be very useful to prevent glare for example after a change in the position of the sun Note in case of joint controlling slat step movements of multiple shutter channels together through the same group address the time configured for this parameter is recommended to be slightly greater than N tenths of a second where N is the amount of the channels that have been enabled and http www zennio com Technical Support http zennioenglish zendesk com 46 Zennio ACTinBOX CLASSIC HYBRID AD configured as blind with slats in order to ensure that rapidly sent consecutive orders are properly processed Note times referred to slat movements must be shorter than those configured for blind movements usual configuration Besides defining these times it will be necessary to configure the following options which are specific for blinds with slats d Maintain slats position when shutter completes motion this option allows choosing whether the slats should recover their position after the blind reaches the desired position or not Example Suppose the parameter Maintain slats positioning when shutter completes motion has been enabled The initial position of the slats is 50 and the initial position of the blind is 0 up An order to lower the blind is receive
11. whereas the second output sends orders to lower the shutter Therefore the cables of the shutter motor carrying out these actions should be properly connected to the corresponding output of the channel to perform the required action Table 1 shows the action carried out by the outputs of each channel http www zennio com Technical Support http zennioenglish zendesk com 7 Zennio ACTinBOX CLASSIC HYBRID AD 1 Move up l 2 Move down 3 Move up i 4 Move down Table 1 Shutter channels actions ofthe outputs Each channel can be configured as a Shutter No Slats or as a Blind with Slats Besides the shutter type ACTinBOX Classic Hybrid allows the configuration of the following functionalities for the shutter channels d Times Sets the main times that define the movement of the shutter the length of the rising movement the length of the descending movement a security time for making a pause in the movement of the motor when the direction changes and an additional movement time when the shutter gets to its limit top or bottom For blinds with slats it is also possible to configure a secondary time for the slat movement length and for the slat step time d Status objects They report the current position of the shutter and of the slats if applicable d Precise control Allows moving the shutter to a particular position defined by parameter Moreover for bli
12. Ch 1 Scene Reception 0 63 Run Scene 1 64 159 1 Byte I C W 18 1 DPT_SceneControl 0 63 Last I6 Ch 2 Scene Reception 0 63 Run Scene 1 64 160 1 Byte CT 18 1 DPT_SceneControl 0 63 Parameteriz Parameteriz I6 Ch 1 Scene Sending 0 63 Send Scene 1 64 161 1 Byte CT 18 1 DPT_SceneControl 0 63 Parameteriz Parameteriz I6 Ch 2 Scene Sending 0 63 Send Scene 1 64 162 2 Bytes CT 9 001 DPT_Value_Temp 273 670760 Parameteriz Parameteriz I5 Current temperature Temperature sensor value 163 1 Bit CT 1 001 DPT_Switch 0 1 0 Last I5 Overcooling 1 Overcooling 0 No Overcooling 164 1 Bit CT 1 001 DPT_Switch 0 1 0 Last I5 Overheating 1 Overheating 0 No Overheating 165 1 Bit o CTR 1 001 DPT_Switch 0 1 Connection dependant Connection dependant 15 Probe Error 1 Error 0 No Error http www zennio com Technical Support http zennioenglish zendesk com 54 Zennio ACTinBOX CLASSIC HYBRID AD BER O A DATA PE DP S A O 166 2 Bytes C W 9 001 DPT_Value_Temp 273 670760 25 Last T1 Temperature Source 1 External Sensor Measure 167 2 Bytes C W 9 001 DPT_Value_Temp 273 670760 25 Last T1 Temperature Source 2 External Sensor Measure 0 Confort 168 1 Byte C W 20 102 DPT_HVACMode ina Parameteriz Parameteriz T1 Special Mode 1 byte HVAC Mode 4 Building Protection goe 1
13. O CTR 9 001 DPT_Value_Temp 0 00 120 00 0 Last LF Function 4 RESULT 2 bytes FUNCTION 4 Result 7 001 DPT_Value_2_Uncount 0 65535 0 Last LF Function 5 RESULT 2 bytes FUNCTION 5 Result 148 2 Bytes O CTR 9 001 DPT_Value_Temp 0 00 120 00 0 Last LF Function 5 RESULT 2 bytes FUNCTION 5 Result 149 1 Bit CT 1 001 DPT_Switch 0 0 0 Reset 0 Voltage Recovery gt Sending of 0 150 1 Bit CT 1 001 DPT_Switch d 1 1 Reset 1 Voltage Recovery gt Sending of 1 151 1 Bit CT 1 001 DPT_Switch 0 1 0 16 Short circuit 1 Short Circuit 0 No Short Cir 152 1 Bit CT 1 001 DPT_Switch 0 1 Connection dependant Connection dependant 16 Open Circuit 1 Open Circuit 0 No Open Circ 153 1 Byte o CTR 5 001 DPT_Scaling 0 100 Parameteriz Last 16 Luminosity level Luminosity on Input 6 1 Bit l C W 1 001 DPT_Switch 0 1 0 I6 Ch 1 Channel block 1 Block 0 Unblock 154 1 Bit l C W 1 001 DPT_Switch 0 1 1 I6 Ch 1 Channel enabling 1 1 003 DPT_Enable 0 Disable 1 Bit I C W 1 001 DPT_Switch 0 1 0 I6 Ch 2 Channel block 1 Block 0 Unblock 155 1 Bit C W 1 001 DPT_Switch 0 1 1 I6 Ch 2 Channel enabling 1 1 003 DPT_Enable 0 Disable 156 1 Bit CT 1 001 DPT_Switch 0 1 Parameteriz Parameteriz I6 Ch 1 Detection Status According to parameters 157 1 Bit CT 1 001 DPT_Switch 0 1 Parameteriz Parameteriz I6 Ch 2 Detection Status According to parameters 158 1 Byte C W 18 1 DPT_SceneControl 0 63 Last I6
14. Support http zennioenglish zendesk com 4 Zennio ACTinBOX CLASSIC HYBRID AD NIK mu Zennio KNR ACTinBOX Classic FEO SE Moi Figure 1 ACTinBOX Classic Hybrid Actuator 1 2 INSTALLATION ACTinBOX Classic Hybrid connects to the KNX bus through the on board KNX connector Once the device is provided with power from the KNX bus both the physical address and the associated application program can be downloaded This actuator does not need any additional external power since it is entirely powered through the KNX bus 1 Outputs 2 Programming button 3 Programming LED 4 KNX connector 5 Inputs Figure 2 ACTinBOX Classic Hybrid Element Scheme The functionality of the main elements of the actuator is described below d Programming button 2 a short press on this button sets the actuator into the programming mode making the associated LED 3 light in red Note if this button is held while plugging the device into the KNX bus ACTinBOX Classic Hybrid goes into secure mode The LED will blink in red every 0 5 S http www zennio com Technical Support http zennioenglish zendesk com 5 Zennio ACTinBOX CLASSIC HYBRID AD d Outputs 1 the screw terminal block bundled with the original packaging must be plugged here to allow the connection of the different systems to be controlled by the actuator Wiring the terminal block may be carried out before
15. Zennio Passion for KNX innovation ZEN ACTinBOX Classic ACTinBOX HYBRID AD ACTinBOX Classic Hybrid Actuator ZN110 AB46A Application program version 2 1 User manual edition 2 1 _a lt Z lt 2 cc lu Kal 5 www zennio com Zennio ACTinBOX CLASSIC HYBRID AD Contents Document update sacas 3 L Iotrogductlon ANC 4 1 1 ACTinBOX Classic Hybrid ooooooccccccnnnoooooncnoncnonanonnononnnnnonnnnn no nnnnnnnnnnnnn ono nnnnnnnnnnnns 4 1 2 Installation tdt tada tada 5 2 Gonliguratio bebe ee ee a 6 2 1 Individual Outputs o a EE Ea a aeaeaei 6 Eege ee e eebe ebe ebe eebe H 2 3 ul cece cee ese eens ae ee eee ee ARARAT ARNNNUG 9 24 Termostato 9 2 5 Relay control sing the IR remote ai 10 3 GENEE 10 3 1 Default Configuration ccccccccccncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnss 11 3 2 i CEET 12 3 2 1 Individual Outputs e aaa aaa aaa aaa aaa aaa aaa aaa aaa aaaaaaaa ar aawakaaaaaaaariaac 12 3 2 2 Shutter chanel 21 3 3 lut e 33 3 3 1 PUSH DUTTON scvecevecececovncece cosasececesnsneeceanansd O AGA CA 34 3 3 2 SS o PP soucesseccceceaes 39 3 3 3 Temperature prObe oooooocccccccnnonoooonnnnnnnnononnnononnnnnncnnnnnnononnnnnnnnnnnnnnnnnnnnnnnnnnnnns 40 3 3 4 Movement detector eeeeeeee eee aaa aaa aaa aaa aaa nnnnnnns 42 3 4 Logical Tunctlons 43 SC Oe E EE 43 ANNEX I Slats precise Control 44 ANNEX II Communication oblects ono nnnnnncon
16. after an ETS download A default or a custom configuration may be selected If default is chosen after a partial or complete download from ETS ACTinBOX Classic Hybrid will assume the shutter is completely up 0 independently of its actual status For blinds with slats ACTinBOX Classic http www zennio com Technical Support http zennioenglish zendesk com 32 Zennio ACTinBOX CLASSIC HYBRID AD Hybrid assumes that the slats are completely open 0 no matter what their actual status is On the other hand after a bus power failure the device will assume the shutter and the slats maintains the same state as before the power failure When custom is chosen ETS will show the following window 3 1 1 1 ACTinBOX Hybrid AD GENERAL SJ lt lt DUTPUTS gt gt CHANNEL A INITIAL POSITION Curent Postion keeps stepped lt lt THERMOSTAT gt gt UPDATE start up position sending No z Figure 19 Custom Start up configuration Where it is possible to configure the following parameters gt Initial position this field defines the desired initial position for the shutter after a bus power failure or after programming the device The following statuses can be chosen Current position keeps stopped up down or specific position which moves the shutter to the position set for Select shutter position and the slats to the position set for Select slats position
17. is received through the object CX Move and stops it with value 1 Therefore if this function is enabled ACTinBOX Classic Hybrid will also raise the shutter when the value 1 is received through object CX Reversed Movement and will lower it on the reception of the value O This reverse control is compatible with the usual control since CX Move and CX Reversed Movement are provided as separate objects for normal and reverse control respectively Reverse control becomes particularly useful when a centralised OFF order is sent over the installation to turn the lights off and to lower the shutters at the same time In this case the value 0 can be sent to the light ON OFF objects and to the shutter Reverse movement objects d Direct positioning this function allows moving the shutter to a preset position by a simple 1 bit order through CX Direct Positioning and CX Direct Positioning 2 When a 1 is received through one of these objects the shutter will be moved to the parameterized position When a 0 is received no action is performed http www zennio com Technical Support http zennioenglish zendesk com 31 Zennio ACTinBOX CLASSIC HYBRID AD 1 1 11 ACTinBOX Hybrid AD k zl GENERAL Direct Positioning lt lt DUTPUTS gt gt CHANNEL A S TOTAL DIRECT POSITIONINGS One y lt lt THERMOSTAT gt gt z SELECT SHUTTER PO
18. provide a detailed explanation about each of the different functionalities of the application in ETS 3 1 DEFAULT CONFIGURATION This section shows the default configuration the device parameterization starts from When the parameter edition is entered for the first time the following window will come up 2 1 11 ACTinBOX Hybrid AD GENERAL GENERAL lt lt THERMOSTAT gt gt Dutputs Na y Inputs No v Logical Functions No y Sending of Indication Objects 0 and 1 on BUS voltage recovery Figure 4 Configuration screen by default As shown in Figure 4 outputs inputs and logical functions are disabled by default so there will be no communication objects available until the user enables some of the functions of the actuator If the parameter Sending of indication objects on bus voltage recovery is set to Yest two new 1 bit communication objects will show up Reset 0 and Reset 1 which will send to the KNX bus the values 0 and 1 after a bus power failure in order to recover the communication with the rest of the devices in the installation This sending may be immediate or after a configured delay in seconds The left side menu also shows the access to the Thermostat configuration disabled by default see Section 3 5 http www zennio com Technical Support http zennioenglish zendesk com 11 Zennio ACTinBOX CLASSIC HYBRID AD 3 2 OUTPUTS
19. zendesk com 43 Zennio ACTinBOX CLASSIC HYBRID AD 5 1 1 ACTinBOX Hybrid AD EJ GENERAL Thermostat 1 lt lt THERMOSTAT gt gt Thermostat 1 Setpoint Thermostat Function Heating x Heating Reference Temperature Temperature Source 1 X Thermostat always ON No X Startup setting on Bus voltage recovery Last before Bus failure MM Automatic ON when a new special mode x B le Disabled X Sending Statuses on BUS voltage recovery No X Figure 27 Thermostat Configuration To find basic theory about the Zennio thermostat as well as information about the related ETS configuration please refer to the specific document Zennio Building Thermostat available at http www zennio com ANNEX I SLATS PRECISE CONTROL Zennio actuators allow controlling the movement of shutters blinds or similar window door automated systems which may be of one of the following types d Shutter No slats d Blind with slats lamellas Depending on the shutter type the ACTinBOX Classic Hybrid application program will show different options This particular section is referred to the parameterization of blinds with slats To begin with it is important to keep in mind the criteria followed by the actuator for shutter positioning d The shutter is in the up position 0 in percentage when it is completely open d The shutter is in the down position 10
20. 0 in percentage when it is completely closed While the slat positioning criteria is as follows http www zennio com Technical Support http zennioenglish zendesk com 44 Zennio ACTinBOX CLASSIC HYBRID AD d The slats are in the up position or open 0 in percentage when their position is such that they can only move downwards d The slats are in the down position or close 100 in percentage when their position is such that they can only move upwards Figure 27 shows a scheme of the positions the slats may adopt It is necessary to take into account that shutter actuators control shutter drives without any feedback about their exact position and that the movement of the slats relays entirely on the movement of shutter drive itself This means that a movement in the slats will always provoke a certain change in the position of the shutter Slats can only move AMD D downward Slats can move M upward A and also downward Slats can only move upward 100 LL Figure 28 Slat positions The ETS configuration screen for Blinds with slats is shown next as well as the details about the available options http www zennio com Technical Support http zennioenglish zendesk com 45 Zennio ACTinBOX CLASSIC HYBRID AD E 111 ACTinBOX Hybrid AD Em GENERAL CHANNEL A lt lt DUTPUTS gt gt CHANNEL A l
21. 0 1 Byte o CTR 5 001 DPT_Scaling 0 100 0 Last T1 Control Variable Heat PI Control Continuous 191 1 Bit o CTR 1 001 DPT_Switch 0 1 0 Last T1 Additional Cool Temp gt Setpoint Band gt 1 192 1 Bit o CTR 1 001 DPT_Switch 0 1 0 Last T1 Additional Heat Temp lt Setpoint Band gt 1 http www zennio com Technical Support http zennioenglish zendesk com 56 Join and send us your inquiries about Zennio devices http zennioenglish zendesk com Zennio Avance y Tecnolog a S L C R o Jarama 132 Nave P 8 11 45007 Toledo Spain Tel 34 925 232 002 Fax 34 925 337 310 www zennio com as C info zennio com K NX Zennio Passion for KNX innovation RoHS
22. 0 2 Bytes O CTR 9 001 DPT_Value_Temp 5 45 Parameteriz Last T1 Basic Setpoint Status Current basic setpoint 181 2 Bytes O CTR 9 002 DPT_Value_Tempd 10 10 0 Last T1 Setpoint Offset Status Current setpoint Offset 1 Bit C W 1 15 DPT_Reset 0 1 0 Parameteriz T1 Offset Reset Reset Offset 1 Bit C W 1 15 DPT_Reset 0 1 0 Parameteriz T1 Setpoint Reset Reset setpoint to default 183 1 Bit l C W 1 100 DPT_Heat_Cool 0 1 Parameteriz Last T1 Mode 0 Cool 1 Heat 184 1 Bit o CTR 1 100 DPT_Heat_Cool 0 1 Parameteriz Last T1 Mode Status 0 Cool 1 Heat 185 1 Bit I C W 1 100 DPT_Heat_Cool 0 1 Parameteriz Last T1 On Off 0 Off 1 On 186 1 Bit o CTR 1 001 DPT_Switch 0 1 Parameteriz Last T1 On Off 0 Off 1 On 1 Bit o CTR 1 001 DPT_Switch 0 1 0 Last T1 Control Variable Cool PI Control PWM wei 1 Bit o CTR 1 001 DPT_Switch 0 1 0 Last T1 Control Variable Cool 2 Point Control 1 Bit o CTR 1 001 DPT_Switch 0 1 0 Last T1 Control Variable Heat PI Control PWM We 1 Bit o CTR 1 001 DPT_Switch 0 1 0 Last T1 Control Variable Heat 2 Point Control 189 1 Byte o CTR 5 001 DPT_Scaling 0 100 0 Last T1 Control Variable Cool PI Control Continuous http www zennio com Technical Support http zennioenglish zendesk com 55 ACTinBOX CLASSIC HYBRID AD Zennio BER O A DATA H DP i A O 19
23. 01 DPT_Switch 0 1 1 Last Ix Short Press 1 Short Pr gt Sending of 1 66 71 1 Bit JO CTRW 1 001 DPT_Switch 0 1 0 Last tx Short Press Switching Short Pr gt Switching 0 1 1 Bit O CTRW 1 007 DPT_UpDown 0 1 0 Last lx Short Press Move Up Shutter Short Pr gt Sending of 0 Up 1 Bit O CTRW 1 007 DPT_UpDown 0 1 1 Last lx Short Press Move Down Shutter Short Pr gt Send of 1 Down 1 Bit JO CTRW 1 007 DPT_UpDown 0 1 0 Last lx Short Press Move Short Pr gt Switching 0 1 http www zennio com Technical Support http zennioenglish zendesk com 50 Zennio ACTinBOX CLASSIC HYBRID AD RA 1 Bit VO CTRW 1 7 DPT_Step 0 1 0 Last lx Short Press Stop Step Up Shutter Short Pr gt Sending of 0 1 Bit VO CTRW 1 7 DPT_Step 0 1 1 Last lx Short Press Stop Step Down Shutter Short Pr gt Sending of 1 1 Bit VO CTRW 1 7 DPT_Step 0 1 0 Last lx Short Press Stop Step Shutter switched Short Pr gt Switching 0 1 1 Bit VO CTRW 1 001 DPT_Switch 0 1 1 Last lx Short Press Dimmer ON Short Pr gt Sending of 1 ON 1 Bit VO CTRW 1 001 DPT_Switch 0 1 0 Last Ix Short Press Dimmer Off Short Pr gt Send of 0 Off 1 Bit VO CTRW 1 001 DPT_Switch 0 1 0 Last Ix Short Press Dimmer Short Pr gt
24. Bit C W 1 001 DPT_Switch 0 1 0 Last T1 Special Mode comfort 0 Off 1 On 1 Bit C W 1 17 DPT_Trigger 0 1 0 Last T1 Special Mode comfort 0 Nothing 1 Trigger 1 Bit C W 1 001 DPT_Switch 0 1 0 Last T1 Special Mode standby 0 Off 1 0n me 1 Bit C W 1 17 DPT_Trigger 0 1 0 Last T1 Special Mode standby 0 Nothing 1 Trigger 1 Bit C W 1 001 DPT_Switch 0 1 0 Last T1 Special Mode economy 0 Off 1 On E 1 Bit C W 1 17 DPT_Trigger 0 1 0 Last T1 Special Mode economy 0 Nothing 1 Trigger 1 Bit C W 1 001 DPT_Switch 0 1 0 Last T1 Special Mode protection 0 Off 1 On are 1 Bit C W 1 17 DPT_Trigger 0 1 0 Last T1 Special Mode protection 0 Nothing 1 Trigger 173 1 Bit C W 1 19 DPT_Window_Door 0 1 0 Last T1 Window Status input 0 Closed 1 Open 174 1 Bit C W 1 17 DPT_Trigger 0 1 0 0 T1 Comfort Prolongation 0 Nothing 1 Timed Comfort 175 1 Byte o CTR 20 102 DPT_HVACMode 0 255 Parameteriz Last T1 Special Mode Status 1 byte HVAC Mode 476 2 Bytes C W 9 001 DPT_Value_Temp 5 45 Parameteriz Last T1 Basic Setpoint Reference setpoint 2 Bytes C W 9 001 DPT_Value_Temp 5 45 Parameteriz Last T1 Setpoint Thermostat setpoint input 177 1 Bit C W 1 7 DPT_Step 0 1 0 Parameteriz T1 Setpoint Step 0 5 C 1 0 5 C 178 2 Bytes C W 9 002 DPT_Value_Tempd 10 10 0 Last T1 Setpoint Offset Float Offset value 179 2Bytes O CTR 9 001 DPT_Value_Temp 5 45 25 Last T1 Setpoint Status Current setpoint 18
25. Darker Lg Pr gt Bright Dark Lg Pr gt Stop 93 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 14 Long Press Brighter Lg Pr gt Bright Lg Pr gt Stop http www zennio com Technical Support http zennioenglish zendesk com 51 Zennio ACTinBOX CLASSIC HYBRID AD BER O A DATA PE DP a 8 A 4Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 14 Long Press Darker Lg Pr gt Dark Lg Pr gt Stop 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 14 Long Press Brighter Darker Lg Pr gt Bright Dark Lg Pr gt Stop 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 15 Long Press Brighter Lg Pr gt Bright Lg Pr gt Stop 94 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 15 Long Press Darker Lg Pr gt Dark Lg Pr gt Stop 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 15 Long Press Brighter Darker Lg Pr gt Bright Dark Lg Pr gt Stop 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 16 Long Press Brighter Lg Pr gt Bright Lg Pr gt Stop 95 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 16 Long Press Darker Lg Pr gt Dark Lg Pr gt Stop 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 16 Long Press Brighter Darker Lg Pr gt Bright Dark Lg Pr gt Stop 1 Byte o CTR 18 1 DPT_SceneControl 0 63 128 191 0 Last 11 Long Press Run Scene Long Pr gt S
26. ECTOR Note this option is only available for input 6 The ACTinBOX Classic Hybrid actuator allows configuring input 6 as a movement detector with the possibility of enabling up to 2 detection channels GENERAL lt lt INPUTS gt gt INPUT 6 Movement detector lt lt THERMOSTAT gt gt INPUT 6 Movement detector Luminosity sending CHANNEL 1 CHANNEL 2 Don t send y o No e Figure 24 Input 6 Movement detector After enabling the desired channels the next configuration screen will be shown GENERAL lt lt INPUTS gt gt INPUT 6 Movement detector lt lt THERMOSTAT gt gt ENABLE BLOCK LENGTH OF DETECTION x 1sec Reset Luminosity after No Detection BLIND TIME x 1sec DETECTION Sent value Send status Delay x 1sec Constrained by luminosity only enabled under threshold NO DETECTION Sent value Send status Delay x 1sec S111 Y 3 CHANNEL 1 Always enabled A 10 No X 0 2 1 switch on X Once y 0 a No X D switch off X Once X o El Figure 25 Channel configuration http www zennio com Technical Support http zennioenglish zendesk com 42 Zennio ACTinBOX CLASSIC HYBRID AD For further information on the behaviour and ETS parameterization of the detection channels please refer to the specific document Motion detector available at http www zennio
27. L lt lt DUTPUTS gt gt DUTPUT 1 DUTPUT 2 lt lt THERMOSTAT gt gt Timers SIMPLE TIMER FLASHING ON Duration x 0 1 sec OFF Duration x 0 1 sec Repetitions 0 Endless Status after last repetition Timers T te 25 25 E 0 OFF y Figure 9 Flashing It is important to keep in mind that ACTinBOX Classic Hybrid allows parameterizing both a simple timer and an intermitting sequence for the same output d Scenes scenes consist of a synchronized activation of the devices in the domotic installation so that different predefined atmospheres can be generated by simply sending a scene value over the bus GENERAL lt lt DUTPUTS gt gt OUTPUT 1 Seene 164 0 Disabled OUTPUT 2 lt lt THERMOSTAT gt gt Response Scene 1 64 0 Disabled Response Scene 1 64 0 Disabled Response Scene 1 64 0 Disabled Response Scene 1 64 0 Disabled Response Scenes OFF y 0 OFF y 0 DFF e 0 OFF 0 OFF z Figure 10 Scenes http www zennio com Technical Support http zennioenglish zendesk com L Zennio ACTinBOX CLASSIC HYBRID AD There is a 1 bye communication object associated with Scenes for the individual outputs Scenes Individual Outputs which shows when the Outputs tab in ETS is enabled even if the outputs are d
28. PT_Switch 0 1 Last LF 1 bit Data Entry 14 Binary Data Entry 0 1 116 1 Bit C W 1 001 DPT_Switch 0 1 Last LF 1 bit Data Entry 15 Binary Data Entry 0 1 117 1 Bit C W 1 001 DPT_Switch 0 1 Last LF 1 bit Data Entry 16 Binary Data Entry 0 1 118 1 Byte C W 5 010 DPT_Value_1_Uncount 0 255 Last LF 1 byte Data Entry 1 1 byte Data Entry 0 255 119 1 Byte C W 5 010 DPT_Value_1_Uncount 0 255 Last LF 1 byte Data Entry 2 1 byte Data Entry 0 255 120 1 Byte C W 5 010 DPT_Value_1_Uncount 0 255 Last LF 1 byte Data Entry 3 1 byte Data Entry 0 255 121 1 Byte C W 5 010 DPT_Value_1_Uncount 0 255 Last LF 1 byte Data Entry 4 1 byte Data Entry 0 255 122 1 Byte C W 5 010 DPT_Value_1_Uncount 0 255 Last LF 1 byte Data Entry 5 1 byte Data Entry 0 255 123 1 Byte C W 5 010 DPT_Value_1_Uncount 0 255 Last LF 1 byte Data Entry 6 1 byte Data Entry 0 255 124 1 Byte C W 5 010 DPT_Value_1_Uncount 0 255 Last LF 1 byte Data Entry 7 1 byte Data Entry 0 255 125 1 Byte C W 5 010 DPT_Value_1_Uncount 0 255 Last LF 1 byte Data Entry 8 1 byte Data Entry 0 255 7 001 DPT_Value_2_Uncount 0 65535 Last 126 2 Bytes C W LF 2 bytes Data Entry 1 2 bytes Data Entry 9 001 DPT_Value_Temp 0 00 120 00 Last 7 001 DPT_Value_2_Uncount 0 65535 Last 127 2 Bytes C W LF 2 bytes Data Entry 2 2 bytes Data Entry 9 001 DPT_Value_Temp 0 00 120 00 Last 7 001 DPT_Value_2_Unco
29. Result http www zennio com Technical Support http zennioenglish zendesk com 53 Zennio ACTinBOX CLASSIC HYBRID AD RA 140 1 Byte o CTR 5 010 DPT_Value_1_Uncount 0 255 0 Last LF Function 2 RESULT 1 byte FUNCTION 2 Result 141 1 Byte o CTR 5 010 DPT_Value_1_Uncount 0 255 0 Last LF Function 3 RESULT 1 byte FUNCTION 3 Result 142 1 Byte o CTR 5 010 DPT_Value_1_Uncount 0 255 0 Last LF Function 4 RESULT 1 byte FUNCTION 4 Result 143 1 Byte o CTR 5 010 DPT_Value_1_Uncount 0 255 0 Last LF Function 5 RESULT 1 byte FUNCTION 5 Result 7 001 DPT_Value_2_Uncount 0 65535 0 Last LF Function 1 RESULT 2 bytes FUNCTION 1 Result 144 2Bytes O CTR 9 001 DPT_Value_Temp 0 00 120 00 0 Last LF Function 1 RESULT 2 bytes FUNCTION 1 Result 7 001 DPT_Value_2_Uncount 0 65535 0 Last LF Function 2 RESULT 2 bytes FUNCTION 2 Result 145 2 Bytes O CTR 9 001 DPT_Value_Temp 0 00 120 00 0 Last LF Function 2 RESULT 2 bytes FUNCTION 2 Result 7 001 DPT_Value_2_Uncount 0 65535 0 Last LF Function 3 RESULT 2 bytes FUNCTION 3 Result 146 2Bytes O CTR 9 001 DPT_Value_Temp 0 00 120 00 0 Last LF Function 3 RESULT 2 bytes FUNCTION 3 Result 7 001 DPT_Value_2_Uncount 0 65535 0 Last LF Function 4 RESULT 2 bytes FUNCTION 4 Result 147 2Bytes
30. SITION 50 SELECT SLATS POSITION 50 NEW POSITIONS SAVING No M Figure 18 Direct positioning It is possible to configure the following parameters gt gt Total direct positionings one or two direct positioning functions can be enabled Select shutter position sets the exact position to move the shutter to 0 Top 100 Bottom For blinds with slats an option called Select Slats position will also become visible making it possible to set a position for the slats when the value 1 is received through the corresponding positioning object If two direct positioning controls are configured two boxes will be available here Select Shutter Position 1 and Select Shutter Position 2 as well as Select Slats position 1 and Select Slats position 2 for blinds with slats New positions saving allows Yes or not No saving new direct positions After enabling this option one or two new communication objects appear depending on the number of direct positioning controls CX Save Position and CX Save Position 2 To overwrite the parameterized direct position it is necessary to send a 1 to these objects when the shutter is at the desired position Note saving a new position is not possible while the shutter is moving d Start up configuration defines the shutter state that the device will assume order when it recovers from a bus power failure or
31. THERMOSTAT TYPE Blind with slats D TIMES Main Time Shutter Length 150 x 0 1 sec Secondary Time Slats Length 20 x 0 1 sec Slats Step Time 2 x 0 1 sec Security Time Pause to change the 5 movement direction x 0 1 sec Are total Time UP and DOWN different No y Additional Time when shutter gets the N limit on Top or at the Bottom a BLIND SPECIFIC Maintain Slats Position when shutter N completes motion 2 Slats Position at Bottom Pos 100 Figure 29 Blinds with slats Configuration screen ETS As shown in Figure 28 for this type of shutters multiple time parameters need to be parameterized On the one hand time parameters referred to the movement of the blind Main Time shutter length Security time Are total time up and down different and Additional time when shutter gets the limit All of them were already explained in Section 3 2 2 of this manual On the other hand time parameters referred to the movement of the slats d Secondary time slats length sets the time in tenths of a second the drive takes to perform a complete slat movement cycle from 0 completely up to 100 completely down or vice versa This time must be manually measured d Slats Step Time sets the time in tenths of a second the drive will keep moving the slats every time it receives the order to perform an up down step movement CX Stop Step 0 or 1
32. Up m Figure 16 Scenes The Scene parameter indicates the scene value the shutter will react to If this value is O the corresponding option is disabled Response sets the precise position where the shutter will be moved to when the above scene number arrives from the bus The shutter can be moved completely up completely down or to a specific intermediate position in percentage from 0 to 100 In case of choosing the latter parameter Shutter specific position will become visible to allow the definition of a specific shutter position through the Select Shutter Position parameter after selecting Yes or to make the shutter stay as is For blinds with slats it is also possible to configure a specific position for the slats via the parameter Select Slats Position when the configured scene number is received or to make them maintain their current position The following example illustrates the configuration process Example Consider a facility where 3 scenes will be distinguished values 4 6 and 18 and where ACTinBOX Classic Hybrid will be used to move a blind with slats to precise positions on the reception of these scene values Scene 4 shutter up http www zennio com Technical Support http zennioenglish zendesk com 27 Zennio ACTinBOX CLASSIC HYBRID AD 2 Scene 6 shutter down d Scene 18 central position 50 The slats maintain their cur
33. annnnnnnnnos 49 http www zennio com Technical Support http zennioenglish zendesk com 2 Zennio ACTinBOX CLASSIC HYBRID AD DOCUMENT UPDATES Version Changes Changes in the application program e Improved management of the output order buffer Example added about the Multiply parameter General revision of texts and styles Changes in the application program e Integration of version 1 1 of the Building Thermostat e Slat precise control and direct positioning implemented http www zennio com Technical Support http zennioenglish zendesk com 3 Zennio ACTinBOX CLASSIC HYBRID AD 1 INTRODUCTION 1 1 ACTINBOX CLASSIC HYBRID ACTinBOX Classic Hybrid is a KNX actuator that combines in only one device the following features d 4 multifunction binary outputs up to 10A each configurable as gt Up to 2 shutter channels with or without slats lamellas gt Up to 4 individual outputs Note outputs 3 and 4 also admit the connection of capacitive loads d 6 specific inputs configurable as gt Inputs 1 4 multifunction binary entries gt Input 5 multifunction binary input or temperature probe gt Input 6 multifunction binary input or movement detector d Zennio Building Thermostat d 5x multi operation logical function module d Manual operation over the actuator outputs by means of the Zennio infrared remote control http www zennio com Technical
34. com 3 4 LOGICAL FUNCTIONS This option in ACTinBOX Classic Hybrid makes it possible to perform mathematical or binary logic operations to incoming values received from the KNX bus and to send the result through other communication objects specifically enabled in the actuator for this purpose Up to 5 different and independent logical functions can be enabled being each of them capable of carrying out up to 4 operations To use any of them it is necessary to enable it from the following ETS screen which becomes available after selecting Yes under Logical Functions in the General parameter screen 2 111 ACTinBOX Hybrid AD GENERAL lt lt LOGICAL FUNCTIONS gt gt lt lt LOGICAL FUNCTIONS gt gt lt lt THERMOSTAT gt gt LOGICAL FUNCTIONS SELECTION FUNCTION 1 Disabled y FUNCTION 2 Disabled y FUNCTION 3 Disabled y FUNCTION 4 Disabled y FUNCTION 5 Disabled y TOTAL DATA ENTRY OBJECTS 1bi 0 1byte D 2bytes D Figure 26 Logical functions To get further information about how to use and parameterize the logical functions please refer to the specific document Logical Functions X5 available at http www zennio com 3 5 THERMOSTAT The ACTinBOX Classic Hybrid actuator offers the possibility to enable and configure one thermostat of the type Zennio Building Thermostat http www zennio com Technical Support http zennioenglish
35. d thus making the blind and therefore the slats start moving downwards until the position of the blind reaches 100 At this point the blind has completed its movement and ACTinBOX Classic Hybrid will revert the position of the slats by additionally moving the drive until they reach the position they had before 50 in this example thus causing a minor deviation in the position of the blind If parameter Maintain slats positioning when shutter completes motion had not been enabled when the position of the blind reaches 100 down the slats will maintain their resulting position after the movement of the blind Slats position at Bottom pos allows establishing the slats position in percentage when the blind is completely closed i e its position is equal to 100 This means that when the blind stops moving downwards and reaches 100 the slats will correct their position to the one established by parameter Apart from these configuration options it is necessary to define the Slats specific position for those enabled functions where particular positions are required to be parameterized These functions are http www zennio com Technical Support http zennioenglish zendesk com 47 Zennio ACTinBOX CLASSIC HYBRID AD gt Scenes Response Specific position The positions of the blind and the slats in percentage can be configured independently gt Alarms Response Specific po
36. d the value 0 to the KNX bus through the Ix Sensor Edge 1 bit object 1 ACTinBOX Classic Hybrid will send the value 1 to the KNX bus through the Ix Sensor Edge 1 bit object Switching 0 1 ACTinBOX Classic Hybrid will send the values 0 and 1 alternatively to the KNX bus through Ix Sensor Edge when a rising edge is detected in the input d Falling edge sets the option to be performed by ACTinBOX Classic Hybrid when it detects a falling edge in the input signal The available options are the same as for Rising edge Sending of 0 delay sets a delay in tenths of a second to be applied by ACTinBOX Classic Hybrid prior to sending the value 0 through Ix Sensor Edge once the corresponding edge has been received from the switch sensor For an immediate response just leave this field as 0 http www zennio com Technical Support http zennioenglish zendesk com 39 Zennio ACTinBOX CLASSIC HYBRID AD d Sending of 1 delay sets a delay in tenths of a second to be applied by ACTinBOX Classic Hybrid prior to sending the value 1 through Ix Sensor Edge once the corresponding edge has been received from the switch sensor For an immediate response just leave this field as O d Periodical sending of 0 sets a period time in seconds if a cyclic sending of the value 0 through the object Ix Sensor Edge is preferred instead of a unique
37. e actual temperature of the room Temperature sending period sets the period time in tens of a second in case a cyclical sending of the current temperature through the Ix Current Temperature communication object is required The value 0 disables the periodical sending d Send with a temperature change ACTinBOX Classic Hybrid will automatically make an extra sending of the value of the current temperature to the KNX bus when due to a temperature increase or decrease the difference between two consecutive measurements is found to be greater or equal than the amount set here from 0 to 200 tenths of a degree To disable this sending simply set this field to O d Temperature protection enables the overheating or the overcooling protection or both together Depending on the option selected one or two communication objects will be enabled I5 Overheating and I5 Overcooling which will show at any time if the upper or lower limits have http www zennio com Technical Support http zennioenglish zendesk com 41 Zennio ACTinBOX CLASSIC HYBRID AD been reached in such case the value 1 will be sent These overcooling overheating limits need to be defined in degrees as well as a if desired a hysteresis value in tenths of a degree which will help prevent consecutive warnings to the bus when the temperature moves continuously around the parameterized limit 3 3 4 MOVEMENT DET
38. e similar times for both directions parameter Are total time up and down different should be set to Yes In such case this Main time will define the time required to move the shutter all the way down while a secondary parameter Total Time Up will become available to define the time required for the inverse movement It is not necessary to periodically calibrate this parameter since the exact shutter position is stored by ACTinBOX Classic Hybrid at any time even after power failures gt Security time pause to change the movement direction this is the time reserved by the actuator as a preventive measure to protect the shutter drive when the movement switches from one direction to the inverse If the device receives an order to lower the shutter while it is being raised ACTinBOX Classic Hybrid will temporarily interrupt the movement security time and will afterwards lower the shutter It is advisable to set a value not lower than 5 tenths of a second the default value gt Are total time Up and Down different Heavy shutters may require different times to move up and to move down When this happens this field should be set to Yes making the already mentioned Main time Shutter length parameter be interpreted as the time required to lower the shutter while a secondary parameter will be provided to define the time required to raise it gt Additional time when the shutter gets the limit t
39. ecting the option that will be carried out when a long press is performed on the pushbutton connected to ACTinBOX Classic Hybrid The available options are the same as for Short press however the orders to increase decrease the light level will not require a second press to be interrupted they will be as soon as the first long press ends d Threshold time defines the minimum time in tenths of a second that the pushbutton must be held in order to consider the action as a long press d Response delay short press sets a delay in tenths of a second for the sending of the object associated to the reaction to the short press Therefore after a short press ACTinBOX Classic Hybrid will wait for this parameterized time before sending the bus the value of the corresponding object For an immediate sending no delay just leave the value 0 for this field d Response delay long press sets a delay in tenths of a second for the sending of the object associated to the reaction to the long press Therefore after a long press ACTinBOX Classic Hybrid will wait for this parameterized time before sending the bus the value of the corresponding object For an immediate sending no delay just leave the value O for this field d Block the Ix Block binary object is enabled making it possible to block any action performed over the ACTinBOX Classic Hybrid input i e disabling the input control by simply sending the value 1
40. elay x 0 1 sec 0 No delay ON Duration x 0 1 sec 0 Endless Multiply No y FLASHING No D Figure 8 Timers screen Simple timer http www zennio com Technical Support http zennioenglish zendesk com 13 Zennio ACTinBOX CLASSIC HYBRID AD gt Simple timer allows switching the output on and off on the reception of the values 1 and 0 through the OX Timer object These switches are subject to a set of parameterizable times e On Delay time the actuator will wait before switching on the output once the ON order has been received through the OX Timer object The value 0 will cause an immediate response e Off delay time the actuator will wait before switching off the output once the OFF order has been received through the OX Timer object The value 0 will cause an immediate response e On Duration time the output remains ON before switching back to the OFF status A 0 in this field means the output will remain permanently ON These parameters apply as follows o When ACTinBOX Classic Hybrid receives a 1 through the OX Timer communication object an ON order is sent to the output after waiting for the On Delay time The output will stay switch off again after the On Duration time if other than 0 o When ACTinBOX Classic Hybrid receives a 0 through the OX Timer communication object an OFF o
41. ending of 0 63 SZ 1 Byte o CTR 18 1 DPT_SceneControl 0 63 128 191 0 Last 11 Long Press Save Scene Long Pr gt Send of 128 191 1 Byte o CTR 18 1 DPT_SceneControl 0 63 128 191 0 Last 12 Long Press Run Scene Long Pr gt Sending of 0 63 ar 1 Byte o CTR 18 1 DPT_SceneControl 0 63 128 191 0 Last 12 Long Press Save Scene Long Pr gt Send of 128 191 1 Byte o CTR 18 1 DPT_SceneControl 0 63 128 191 0 Last 13 Long Press Run Scene Long Pr gt Sending of 0 63 ww 1 Byte o CTR 18 1 DPT_SceneControl 0 63 128 191 0 Last 13 Long Press Save Scene Long Pr gt Send of 128 191 1 Byte o CTR 18 1 DPT_SceneControl 0 63 128 191 0 Last 14 Long Press Run Scene Long Pr gt Sending of 0 63 1 Byte o CTR 18 1 DPT_SceneControl 0 63 128 191 0 Last 14 Long Press Save Scene Long Pr gt Send of 128 191 1 Byte o CTR 18 1 DPT_SceneControl 0 63 128 191 0 Last 15 Long Press Run Scene Long Pr gt Sending of 0 63 e 1 Byte o CTR 18 1 DPT_SceneControl 0 63 128 191 0 Last 15 Long Press Save Scene Long Pr gt Send of 128 191 1 Byte o CTR 18 1 DPT_SceneControl 0 63 128 191 0 Last 16 Long Press Run Scene Long Pr gt Sending of 0 63 Ko 1 Byte o CTR 18 1 DPT_SceneControl 0 63 128 191 0 Last 16 Long Press Save Scene Long Pr gt Send of 128 191 102 1 Bit C W 1 001 DPT_Switch 0 1 Last LF 1 bit Data Entry 1 Binary Data Entry 0 1 103 1 Bit C W 1 001 DPT_Switc
42. ep Down the Ix Short press Stop Step down shutter 1 bit communication object becomes enabled and will send the KNX bus the stop shutter order value 1 If the shutter was not in motion this stop http www zennio com Technical Support http zennioenglish zendesk com 35 Zennio ACTinBOX CLASSIC HYBRID AD order performs a short movement downwards in the case of blinds with slats this permits moving them one step down In both cases the value sent to the KNX bus is 1 Stop Switched Step the Ix Short Press Stop Step Shutter switched 1 bit communication object becomes enabled and will send the KNX bus the stop shutter order with values 1 and 0 alternating after every short press If the shutter was not in motion this stop order performs a short movement upwards or downwards in the case of blinds with slats this permits moving them one step up or down gt Dimmer control This function allows sending the KNX bus orders to control a dimmer light regulator The field Response is provided for the selection of the order to be sent after a short press Light ON the Ix Short press Dimmer ON 1 bit communication object becomes enabled and will send the KNX bus a switch on order value 1 after a short press Light OFF the Ix Short press Dimmer OFF 1 bit ommunication object becomes enabled and will send the KNX bus a switch off order value 0 after a short pres
43. g the actuator outputs by making use of the Zennio infrared remote control the one used to control the InZennio Z38i and ZAS touch panels See Figure 3 Note fo control the outputs from the IR remote it is necessary to have the programming LED on lighting in red The control of the outputs is carried out as follows d Press over the right button closes the relay of the corresponding output d Press over the left button opens the relay of the corresponding output Figure 3 shows a representation of the buttons of the IR remote that must be pressed depending on the output to be remotely controlled Output 1 Output 2 we Output 4 Figure 3 Controlling the outputs from the IR remote The IR control of the device outputs is only provided for testing purposes None of the parameterized functions such as scenes timers etc is taken into account for opening closing the relays remotely 3 ETS PARAMETRIZATION To begin with the parameterization of the ACTinBOX Classic Hybrid actuator it is necessary once the ETS application is running to import the database of the product ACTinBOX Hybrid AD application program http www zennio com Technical Support http zennioenglish zendesk com 10 Zennio ACTinBOX CLASSIC HYBRID AD Next the device must be added to the project where desired Finally right click on the device and select Edit parameters to start with the configuration The following sections
44. h 0 1 Last LF 1 bit Data Entry 2 Binary Data Entry 0 1 104 1 Bit C W 1 001 DPT_Switch 0 1 Last LF 1 bit Data Entry 3 Binary Data Entry 0 1 105 1 Bit C W 1 001 DPT_Switch 0 1 Last LF 1 bit Data Entry 4 Binary Data Entry 0 1 106 1 Bit C W 1 001 DPT_Switch 0 1 Last LF 1 bit Data Entry 5 Binary Data Entry 0 1 107 1 Bit C W 1 001 DPT_Switch 0 1 Last LF 1 bit Data Entry 6 Binary Data Entry 0 1 108 1 Bit C W 1 001 DPT_Switch 0 1 Last LF 1 bit Data Entry 7 Binary Data Entry 0 1 109 1 Bit C W 1 001 DPT_Switch 0 1 Last LF 1 bit Data Entry 8 Binary Data Entry 0 1 110 1 Bit C W 1 001 DPT_Switch 0 1 Last LF 1 bit Data Entry 9 Binary Data Entry 0 1 111 1 Bit C W 1 001 DPT_Switch 0 1 Last LF 1 bit Data Entry 10 Binary Data Entry 0 1 112 1 Bit C W 1 001 DPT_Switch 0 1 Last LF 1 bit Data Entry 11 Binary Data Entry 0 1 113 1 Bit C W 1 001 DPT_Switch 0 1 Last LF 1 bit Data Entry 12 Binary Data Entry 0 1 114 1 Bit C W 1 001 DPT_Switch 0 1 Last LF 1 bit Data Entry 13 Binary Data Entry 0 1 http www zennio com Technical Support http zennioenglish zendesk com 52 Zennio ACTinBOX CLASSIC HYBRID AD RA 115 1 Bit C W 1 001 D
45. hat a cyclical monitoring period of 3 minutes is configured The trigger value is 1 and the reaction of the actuator when the alarm is activated consists in moving the shutter all the way up while when the alarm is deactivated the shutter will be raised Assuming that the shutter has been lowered when the alarm becomes active the actuator will begin raising the shutter While the alarm is not deactivated any action over the shutter channel will be ignored by the actuator After some time t2 one 0 arrives through the alarm object which makes the alarm turn off and the shutter be raised Before the parameterized cyclical monitoring period 3 minutes ends a new alarm deactivation order arrives so the time count starts again After 3 minutes without receiving further values through the alarm object the alarm will be automatically http www zennio com Technical Support http zennioenglish zendesk com 29 Zennio ACTinBOX CLASSIC HYBRID AD activated making the shutter move up again As before any action over the shutter will be ignored until the alarm is deactivated See the following figure CX Alarm 1 Automatic Alarm CX Alarm 0 Activation CX Alarm 0 Output status 3 minutes 3 minutes gt Response sets the response order to be sent to the shutter when the alarm is activated e Stop e Up e Down e Specific position When the latter is chosen a new drop down l
46. he parameterized time being n the number of times the value 0 is received Note the Multiply option may result particularly useful under parameterizations with no ON and OFF delays Nevertheless as already explained and as the following example shows these delay times if parameterized with a value other than 0 do also admit multiplication http www zennio com Technical Support http zennioenglish zendesk com 15 Zennio ACTinBOX CLASSIC HYBRID AD Example the following is parameterized On Delay 3 seconds Off Delay 3 seconds On Duration 5 seconds The graphs bellow reflect some possible situations if the values 0 or 1 are received from the which is represented as gt 0 and 1 respectively for the cases of having the multiply option enabled and disabled With no multiplication http www zennio com Technical Support http zennioenglish zendesk com 16 Zennio ACTinBOX CLASSIC HYBRID AD gt Flashing Figure 9 This function allows the execution of alternating ON OFF sequences when needed It is possible to parameterize the ON and an OFF time length as well as the number of repetitions the value 0 makes the sequence endless until a 0 is received through the OX Flashing communication object It is also possible to define the final status ON or OFF of the output after the last repetition GENERA
47. his parameter is useful to prevent small maladjustments and to ensure that the shutter always gets to the lowest or highest position This is done by defining an extra time to keep the drive moving once the rising lowering times end This parameter is not visible by default however it is advisable to give it a value to guarantee a proper behaviour in the shutter http www zennio com Technical Support http zennioenglish zendesk com 24 Zennio ACTinBOX CLASSIC HYBRID AD If the shutter is configured as a blind with slats Figure 14 some more specific parameters appear All of them are explained in detail in ANNEX I Slats precise control Note after programming the device from ETS from ETS and unless a custom start up configuration has been parameterized ACTinBOX Classic Hybrid will assume the shutter as completely raised so any raising order will be ignored The following is an example of a possible shutter configuration Example Channel A shutter without slats takes 15 seconds to be lowered and 20 to be raised Additional times for direction changes 5 tenths of a second and at the end of the movement 2 seconds are also required The required parameterization is as follows TYPE Shutter No slats NOTE Slats Positions will be ignored for Shutter types TIMES Main Time Shutter Length 150 z x 0 1 sec z Security Time Pause to change the 5 movement direction x 0 1 sec
48. hutter Position 0 0 Top 255 100 Bottom http www zennio com Technical Support http zennioenglish zendesk com 49 Zennio ACTinBOX CLASSIC HYBRID AD BER O A DATA PE DP S A O 40 1 Byte C W 5 001 DPT_Scaling 0 255 0 Parameteriz CA Shutter Positioning 0 0 Top 255 100 Bottom 41 1 Byte C W 5 001 DPT_Scaling 0 255 0 Parameteriz CB Shutter Positioning 0 0 Top 255 100 Bottom 1 Bit C W 1 5 DPT_Alarm 0 1 Last CA Alarm 0 Alarm 1 No Alarm gt 1 Bit C W 1 5 DPT_Alarm 0 1 Last CA Alarm 1 Alarm 0 No Alarm 1 Bit C W 1 5 DPT_Alarm 0 1 Last CA Alarm 2 0 Alarm 1 No Alarm di 1 Bit C W 1 5 DPT_Alarm 0 1 Last CA Alarm 2 1 Alarm 0 No Alarm 1 Bit C W 1 5 DPT_Alarm 0 1 Last CB Alarm 1 Alarm 0 No Alarm 1 Bit C W 1 5 DPT_Alarm 0 1 Last CB Alarm 0 Alarm 1 No Alarm 1 Bit C W 1 5 DPT_Alarm 0 1 Last CB Alarm 2 0 Alarm 1 No Alarm Bi 1 Bit C W 1 5 DPT_Alarm 0 1 Last CB Alarm 2 1 Alarm 0 No Alarm 46 1 Bit C W 1 16 DPT_Ack 0 1 0 Last CA Unfreeze Alarm Alarm 0 Unf 1 gt End Alarm 47 1 Bit C W 1 16 DPT_Ack 0 1 0 Last CB Unfreeze Alarm Alarm 0 Unf 1 gt End Alarm 48 1 Bit C W 1 17 DPT_Trigger 0 1 0 Last CA Direct Positioning 1 Go to Position 0 No Action 49 1 Bit C W 1 17 DPT_Trigger 0 1 0 Last CA
49. ined in section 3 of this manual Input 5 may be configured as a binary input or as a temperature probe For this configuration it will be possible to set different parameters regarding the measurement and sending of the temperature Input 6 may be configured as a binary input or as a movement detector For this configuration up to 2 different detection channels can be enabled and configured to react on movement detections or on the absence of movement by setting custom timings As a result of the movement detection or non detection the channel will transmit the corresponding information through the KNX bus provided that the channel is enabled not locked The movement detector also features a luminosity sensor that allows configuring the sending of the movement detection or non detection restricted to a luminosity level according to the parameterization 2 4 THERMOSTAT It is possible to enable and configure one thermostat with the Building functionality The operation and ETS configuration of the Zennio thermostat are described in the specific documentation Zennio Building Thermostat available at http www zennio com http www zennio com Technical Support http zennioenglish zendesk com 9 Zennio ACTinBOX CLASSIC HYBRID AD 2 5 RELAY CONTROL USING THE IR REMOTE The ACTinBOX Classic Hybrid actuator incorporates a built in infrared receiver located next to the programming LED This functionality allows testin
50. isabled In the case of the individual outputs scenes allow linking a numerical value between 1 and 64 where O means that the option is disabled to an output status OFF or ON Thus when the predefined scene value is received through the Scenes object the parameterized action for the output a switch off or a switch on will be performed so it will be possible to create different environments in the installation Besides running scenes it is possible to learn save scenes taking into account that the associated numerical values for learning scenes are in the range 128 191 ACTinBOX Classic Hybrid allows running and or learning up to 5 different scenes for each output Alarm for each output it is possible to configure an alarm which once activated will have priority over the rest of the orders that the actuator may recelve i e any order received while the alarm is active will be ignored until the alarm becomes inactive 5 1 1 1 ACTinBOX Hybrid AD GENERAL lt lt DUTPUTS gt gt OUTPUT 1 TRIGGER VALUE 1 OUTPUT 2 CYCLICAL MONITORING PERIOD 0 2 lt lt THERMOSTAT gt gt x 1 min O Disabled RESPONSE No Change e DEACTIVATION Mei alarm acknowledgement cma END reaction when alarm ends No Change e Alarm Figure 11 Alarm The following parameters can be configured for alarms gt Trigger value sets the value that will trigger the ala
51. ist is shown letting the integrator set a value for this specific position in the range 0 completely up to 100 completely down For blinds with slats an option called Select Slats position will also become visible making it possible to set a position for the slats between 0 totally open or up and 100 totally closed or down gt Deactivation two different procedures are provided to deactivate an active alarm e Normal depending on what was parameterized under Trigger Value the alarm will be deactivated as soon as the actuator receives a 0 or a 4 through the corresponding alarm object http www zennio com Technical Support http zennioenglish zendesk com 30 Zennio ACTinBOX CLASSIC HYBRID AD e Frozen this method requires a normal deactivation plus the reception of the value 1 over the corresponding unfreeze alarm object if the latter does not occur the alarm status will still be active This method makes the channel output remain locked even when the alarm situation is over until it is externally or manually enabled gt End this parameter sets the desired shutter position once the alarm becomes inactive e Current position e Up e Down e Last position before the alarm d Reverse movement this function makes it possible to control a shutter with the usual orders inverted ACTinBOX Classic Hybrid normally raises the shutter when the value 0
52. ject CX Shutter Positioning in percentage Every time ACTinBOX Classic Hybrid receives a new percentage value through this object e g 50 the shutter moves to the corresponding position e g the central position For blinds with slats the actuator also implements the 1 byte object CX Slats Positioning for setting the desired position in percentage for the slats d Scenes this function makes it possible to use scenes to control the shutters It allows choosing precise positions where the shutter will be moved to upon the reception of certain scene numbers through the 1 byte object Scenes Shutter Channels Apart from running scenes it is possible to learn save scenes taking into account that the values that should be received to learn a scene must be in the range 128 191 values 0 63 are reserved for running scenes Up to 5 scenes can be run and or leant for each shutter channel http www zennio com Technical Support http zennioenglish zendesk com 26 Zennio ACTinBOX CLASSIC HYBRID AD 311 11 ACTinBOX Hybrid AD GENERAL Scenes lt lt QUTPUTS gt gt CHANNEL A Sears e x Scenes 1 64 0 Disabled Z lt lt THERMOSTAT gt gt pS ek y Up Down 0 Scene 1 64 0 Disabled Response Up y Scene 1 64 0 Disabled Response Up m Scene 1 64 0 Disabled Response Up m Scene 1 64 0 Disabled Response
53. ll be ignored The channel outputs will become unlocked when a 0 is sent through this object Note only the alarm function has a higher priority than the block function If an alarm signal arrives while the channel is locked the shutter will adopt the position http www zennio com Technical Support http zennioenglish zendesk com 21 Zennio ACTinBOX CLASSIC HYBRID AD configured for the alarm Once the alarm is deactivated the shutter will recover the position defined for the locked status The first parameter to be configured is the type of the shutter d Shutter no slats typical shutter with a simple movement up down If this type is selected two communication objects are enabled CX Move and CX Stop to move the shutter up down and to stop it respectively In addition the following remark is shown for this type Slats positions will be ignored for Shutter types which means that function parameters related to slat positions will not be taken into account d Blind with slats special slat shutters where both the shutter itself and the slats lamellas are controlled with a single drive ACTinBOX Classic Hybrid allows controlling both movements the slat rotation which permits varying the level of the incident light and the movement up down of the blind Two communication objects are enabled for this purpose CX Move which will send the orders to move the blind u
54. llowing communication objects 1 bit each d OX ON OFF allows activating ON or deactivating OFF the corresponding output by sending the value 1 or 0 depending on the parameterized output type d OX Status shows the current status of the output active or inactive d OX Block allows locking unlocking the output e disabling enabling its control by sending the values 1 or 0 to the object respectively Note only the Alarm function has a higher priority than the block function if an alarm signal arrives when the output is locked the output will be set to the status defined by the alarm function When the alarm gets deactivated the output returns to the lock status The first thing to be parameterized is the type of each output of the channel d Normally open the output will be considered as active ON when the relay stays closed and inactive OFF when the relay stays open d Normally closed the output will be considered as active ON when the relay stays open and inactive OFF when the relay stays closed Next the list of functions available for each output d Timers allow performing a timed control of the outputs both through a simple timer and or through an intermittent sequence flashing 3 111 ACTinBOX Hybrid AD Ea GENERAL Timers lt lt DUTPUTS gt gt DUTPUT 1 la Yes z DUTPUT 2 ON Delay 0 lt lt THERMOSTAT gt gt x 0 1 sec 0 No delay z OFF D
55. n lt lt INPUTS gt gt INPUT 1 Push Button i lt lt THERMOSTAT gt gt SHORT PRESS No Action D LONG PRESS No Action y THRESHOLD TIME 5 pressing down x 0 1 sec Y RESPONSE DELAY after Short Press 0 x x 0 1 sec Y RESPONSE DELAY after Long Press x 0 1 sec y BLOCK No y Figure 21 Binary input Push button From the default window Figure 20 it will be possible to customize the behaviour of the push button connected to the actuator input through the following options d Short press it allows selecting an action to be carried out after a short press on the pushbutton connected to the input channel The options are gt No action Nothing no action is performed gt Sending of 0 1 A new window is shown from which through the Response field it is possible to select a value that will be sent to the KNX bus after a short press e 0 the Ix Short press 0 binary communication object becomes visible and will send the value 0 to the bus after a short press http www zennio com Technical Support http zennioenglish zendesk com 34 Zennio ACTinBOX CLASSIC HYBRID AD 4 the Ix Short press 1 binary communication object becomes visible and will send the value 0 to the bus after a short press gt Switching 0 1 the Ix Short press Switching binary communication object becomes visible and will perform an alternate sending of the value
56. n input 5 is configured as a temperature probe the ETS topology window will show the communications objects I5 Current Temperature 2 bytes and I5 Probe Error http www zennio com Technical Support http zennioenglish zendesk com 40 Zennio ACTinBOX CLASSIC HYBRID AD 1 bit The first one reports the temperature value measured by the probe connected to ACTinBOX Classic Hybrid while through the second object it is possible to monitor errors due to a wrong connection of the probe or a defective probe in such case the object will acquire the value 1 and will be sent every 30 seconds Once the problem is solved the error object acquires the value 0 again The default configuration screen of the temperature sensor is shown in Figure 22 111 ACTinBOX Hybrid AD GENERAL INPUT 5 Temp Sensor lt lt INPUTS gt gt INPUT 5 Temp Sensor Temperature Sensor CALIBRATION 0 lt lt THERMOSTAT gt gt x 0 120 Temperature sending PERIOD 3 x 10sec O Disabled Send with a Temperature Change 0 x 0 1 SC O Disabled Temperature protection Na X Figure 23 Input 5 Temperature probe The following parameters can be parameterized d Temperature sensor calibration allows making an adjustment by setting a positive or negative value in tenths of a degree over the measured temperature when due to whatever external factor a deviation is found between the measured value and that of th
57. nds with slats it is also possible to establish a particular position for the slats value between 0 and 100 d Scenes Allows running and or saving a specific action over the channel s where this function is enabled Alarms Two alarms are available for each shutter channel The parameterized action will be executed when an alarm event is received d Reverse movement Allows inverse shutter control d Direct positioning Function that permits moving the shutter to a preset specific position by sending a 1 bit communication object d Start up configuration Default or custom All these options are explained in detail in section 3 ETS Parametrization http www zennio com Technical Support http zennioenglish zendesk com 8 Zennio ACTinBOX CLASSIC HYBRID AD 2 3 INPUTS The actuator ACTinBOX Classic Hybrid features 6 inputs which may be configured as Binary input all inputs 1 6 d Temperature probe only input 5 d Movement detector only input 6 Depending on the selected configuration it may be necessary to connect different external elements to the actuator inputs push buttons or switches temperature probes like model ZN1AC NTC68 S E F from Zennio or movement sensors like model ZN1IO DETECT from Zennio Inputs configured as binary inputs may be push buttons or switches sensors depending on the connected element For every type different customizable options are available as expla
58. p Down Shutter Long Pr gt Sending of 1 1 Bit O CTRW 1 7 DPT_Step 0 1 0 Last lx Long Press Stop Step Shutter switched Long Pr gt Switching 0 1 1 Bit JO CTRW 1 001 DPT_Switch 0 1 0 Last Ix Long Press 0 Long Pr gt Sending of 0 1 Bit JO CTRW 1 001 DPT_Switch 0 1 0 Last lx Long Press 1 Long Pr gt Sending of 1 1 Bit O CTRW 1 001 DPT_Switch 0 1 0 Last lx Long Press Switching Long Pr gt Switching 0 1 4 Bit O CTR 3 007 DPT_Control_Dimming 0 15 0 Last 11 Long Press Brighter Lg Pr gt Bright Lg Pr gt Stop 90 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 11 Long Press Darker Lg Pr gt Dark Lg Pr gt Stop 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 11 Long Press Brighter Darker Lg Pr gt Bright Dark Lg Pr gt Stop 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 12 Long Press Brighter Lg Pr gt Bright Lg Pr gt Stop 91 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 12 Long Press Darker Lg Pr gt Dark Lg Pr gt Stop 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 12 Long Press Brighter Darker Lg Pr gt Bright Dark Lg Pr gt Stop 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 18 Long Press Brighter Lg Pr gt Bright Lg Pr gt Stop 92 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last I3 Long Press Darker Lg Pr gt Dark Lg Pr gt Stop 4 Bit o CTR 3 007 DPT_Control_Dimming 0 15 0 Last 18 Long Press Brighter
59. p down and CX Stop Step If the device receives a 0 or a 1 through the latter when the blind is already in motion the movement will be interrupted while if the blind was not in motion receiving a O through this communication object will make the slats rotate upwards while receiving a 1 will make them rotate downwards These step movements are useful to correct both the slat and the blind position together To get detailed information about blinds with slats and their ETS configuration please refer to ANNEX I Slats precise control The next figures show the screens that contain the parameterizable options for channels configured as shutters no slats or as blinds with slats http www zennio com Technical Support http zennioenglish zendesk com 22 Zennio ACTinBOX CLASSIC HYBRID AD GENERAL lt lt DUTPUTS gt gt CHANNEL A lt lt THERMOSTAT gt gt GENERAL lt lt DUTPUTS gt gt CHANNEL A CHANNEL B lt lt THERMOSTAT gt gt Apart from the shutter type it is necessary to configure some specific functions which are common to both types TPE NOTE Slats Positions will be ignored for Shutter types TIMES Main Time Shutter Length x 0 1 sec Security Time Pause to change the movement direction x 0 1 sec Are total Time UP and DOWN different Additional Time when shutter gets the limit on Top or at the Bottom
60. rder is sent to the output after waiting for the Off Delay time e Multiply allows progressively increasing multiplying in runtime the On Duration time or the On Off delays of the output Two situations are distinguished o No multiply If the On delay count is already running it will be reset every time a new 1 is received through the OX Timer object If the output has already been activated and the On Duration time is counting it will be reset whenever a new 1 is received http www zennio com Technical Support http zennioenglish zendesk com 14 Zennio ACTinBOX CLASSIC HYBRID AD If the Off delay count is already running it will be reset every time a new 0 is received o Multiply If the On delay count is already running and the value 1 is received several times through the OX Timer object then the actual delay time will be mn times the parameterized time being n the number of times the value 1 is received If the output has already been activated and while the On Duration time is counting the value 1 is received several times then the actual duration will be n times the e parameterized time being n the number of times the value 1 is received If the Off delay count is already running and the value 0 is received several times then the actual delay time will be n times t
61. rent position The associated parameterization should be as follows Scenes Scene 4 1 64 0 Disabled Response Up e Scene 6 gt 1 64 0 Disabled Response Down m Scene 18 a 1 54 0 Disabled z Response Specific Position X Shutter Specific Position Yes Move to Position z Select Shutter Position 2 50 Slats Specific Position No Current Position will be maintained Z d Alarms ACTinBOX Classic Hybrid allows configuring up to 2 alarms for each shutter channel This function is designed for cases in which the actuator must react to an alarm situation Having two alarms configured allows carrying out different reactions to two external events 1 1 1 ACTinBOX Hybrid AD GENERAL Alarms lt lt DUTPUTS gt gt CHANNEL A i AIZ NUMBER OF ALARMS One lt lt THERMOSTAT gt gt TRIGGER YALUE z SA CYCLICAL MONITORING PERIOD 0 z x 1 min O Disabled z RESPONSE Stop DEACTIVATION p alarm acknowledgement ama A Current Position e Figure 17 Alarms The following parameters can be configured gt Number of alarms sets whether to use one or two alarms Both of them can be independently managed through their corresponding communication objects CX Alarm for Alarm 1 and CX Alarm 2 for the second one http www zennio com Technical Support http zennioenglish zendesk com
62. rm status lt can be 1 or 0 The alarm status will be activated when the value set in this field is sent to the OX Alarm object and it will be deactivated when the opposite value is sent to the aforementioned communication object http www zennio com Technical Support http zennioenglish zendesk com 18 Zennio ACTinBOX CLASSIC HYBRID AD Cyclical monitoring period minutes defines for the case of having a periodically sent alarm object 1 or O as corresponding each time the maximum permitted time without receiving the no alarm value OX Alarm value contrary to the parameterized trigger value before the actuator automatically assumes the alarm status foreseeing the possibility of a failure in the transmitting device If for whatever reason the monitoring period expires ACTinBOX Classic Hybrid will trigger the parameterized action unless it does not imply a change in the output status This will not happen while the no alarm value keeps being sent before each monitoring period expires The cyclical monitoring can be disabled by simply setting a O under this filed The following example is provided for a better comprehension Example Suppose that a cyclical monitoring period of 2 minutes is configured The trigger value is 1 and the reaction of the actuator when the alarm is activated consists in switching on the output while when the alarm is deactivated the ou
63. s 0 and 1 to the bus on short presses The transmission of the selected value can be carried out cyclically i e it is possible to parameterize a periodical sending to the KNX bus through the field Cyclical response sending gt Shutter control This function allows sending the KNX bus a 1 bit object to control shutters The field Response defines the order to be sent after a short press Up the Ix Short press Move up shutter 1 bit communication object becomes enabled and will send the KNX bus the move up order value Q after a short press Down the Ix Short press Move down shutter 1 bit object becomes enabled and will send the KNX bus the move down order value 1 after a short press Up Down switched the Ix Short press Move up down shutter 1 bit communication object becomes enabled and will perform an alternate sending to the KNX bus of the orders to move up and to move down the shutter values 0 and 1 respectively after short presses This option allows handling the shutter through just one input button Stop Step Up the Ix Short press Stop Step up shutter 1 bit communication object becomes enabled and will send the KNX bus the stop shutter order value 0 If the shutter was not in motion this stop order performs a short movement upwards in the case of blinds with slats this permits moving them one step up In both cases the value sent to the KNX bus is 0 Stop St
64. s Light ON OFF switched the Ix Short press Dimmer ON OFF 1 bit communication object becomes enabled and will send the KNX bus an alternate switch order values 1 and 0 respectively for switch on and switch off orders after short presses Brighter the Ix Short press Brighter 4 bit communication object becomes enabled and will send the dimmer after a short press an order to increase the light level according to the parameterized dimming step see Table 2 A second short press will send an order to interrupt the dimming process value 0 Darker the Ix Short press Darker 4 bit communication object becomes enabled and will send the dimmer after a short press an order to decrease the light level according to the parameterized dimming step see Table 2 A second short press will send an order to interrupt the dimming process value 8 http www zennio com Technical Support http zennioenglish zendesk com 36 Zennio ACTinBOX CLASSIC HYBRID AD e Brighter Darker switched the Ix Short press Brighter darker A but communication object becomes enabled and will send the dimmer after a short press an order to increase the light level according to the parameterized dimming step see Table 2 A second short press will send an order to interrupt the dimming process 0 A third press Causes sending an order to decrease the light level while another one will interrupt such order
65. sending ACTinBOX Classic Hybrid will send this value to the KNX bus in cyclically and endlessly according to the parameterized time For a non cyclical sending simply set a O as the period time d Periodical sending of 1 sets a period time in seconds if a cyclic sending of the value 1 through the object Ix Sensor Edge is preferred instead of a unique sending ACTinBOX Classic Hybrid will send this value to the KNX bus in cyclically and endlessly according to the parameterized time For a non cyclical sending simply set a O as the period time d Block the Ix Block binary object is enabled making it possible to block any action performed over the ACTinBOX Classic Hybrid input e disabling the input control by simply sending the value 1 through the block object after which ACTinBOX Classic Hybrid will ignore any edges or signals received from the input device Once the value 0 arrives the input will be enabled again Actions or edges received while the input is locked will not be taken into account when the input becomes unlocked again d Sending Status on Bus voltage recovery if enabled the status of the ACTinBOX Classic Hybrid input will be automatically sent after the parameterized delay in seconds to the bus values 0 and 1 depending of which one applies when the device recovers from a bus power failure 3 3 3 TEMPERATURE PROBE Note this option is only available for input 5 Whe
66. sition The same as above gt Direct positioning Independent configuration of positions 1 or 2 depending on the parameterized number in percentage of the blind and the slats gt Start up configuration Initial position Specific position The position percentages of the blind and slats can be configured independently To obtain further information about the configuration and options of the functions of the shutter channels please refer to the section 3 2 2 of this manual http www zennio com Technical Support http zennioenglish zendesk com 48 Zennio ACTinBOX CLASSIC HYBRID AD ANNEX II COMMUNICATION OBJECTS Column RESET shows the values of the communication objects after a bus failure However this does not necessarily imply that such values are sent to the bus NUMBER SIZE I O FLAGS DATA TYPE DPT ko FUNCTION AAA 1ST TIME 0 1 Byte C W 18 1 DPT_SceneControl Gero Scenes Individual Outputs 0 63 Run 1 64 128 191 Learn 1 1 Byte C W 18 1 DPT_SceneControl de doi eer Scenes Shutter Channels 0 63 Run 1 64 128 191 Learn 1 Bit C W 1 001 DPT_Switch 0 1 Parameteriz Parameteriz Ox ON Off N O 0 Open Relay 1 Close ES 1 Bit C W 1 001 DPT_Switch 0 1 Parameteriz Parameteriz Ox ON Off N C 0 Close Relay 1 Open 6 9 1 Bit o CTR 1 001 DPT_Switch 0 1 Parameteri
67. tart up position sending 2 Figure 12 Start up configuration custom Where the following parameters can be configured gt Initial status this field defines the initial status of the output after a bus power failure or after a download The following options are available last saved position e the status of the output before the bus power failure ON or OFF gt Update enabling this field Yes will make the actuator send the output status to the bus through the corresponding communication object after the start up as a feedback for the rest of the devices in the installation A parameterizable delay can also be applied to this sending If the delay is set to 0 the status will be sent immediately The initial status is always sent through the object OX Status 3 2 2 SHUTTER CHANNEL ACTinBOX Classic Hybrid also allows configuring its outputs as shutter channels making it possible to control up to 2 separate shutters in an installation When a channel is configured in ETS as a shutter channel a 1 bit communication object CX Block related to each enabled channel becomes visible This object allows locking the channel outputs i e disabling the control over them through both the ON OFF and the timed control objects when it is received with value 1 Moreover if the shutter is already moving at the moment of being locked the movement will be interrupted and any order over it wi
68. through the block object after which ACTinBOX Classic Hybrid will ignore any press or signal received from the input device Once the value 0 arrives the input will be enabled again Actions or presses performed while the input is locked will not be taken into account when the input becomes unlocked again http www zennio com Technical Support http zennioenglish zendesk com 38 Zennio ACTinBOX CLASSIC HYBRID AD 3 3 2 SWITCH SENSOR Je 3 1 11 ACTinBOX Hybrid AD k zel GENERAL lt lt INPUTS gt gt The default window Figure 21 provides with the required parameters to customize the INPUT 1 Switch Sensor lt lt THERMOSTAT gt gt INPUT 1 Switch Sensor RISING EDGE No Action y FALLING EDGE No Action y Sending of 0 DELAY x 0 1 sec Sending of 1 DELAY x 0 1 sec PERIODICAL SENDING OF 0 x 1 sec O No cyclical sending PERIODICAL SENDING OF 1 x 1 sec O No cyclical sending 0 0 0 0 BLOCK No y Sending of Status 0 and 1 on BUS Na voltage recovery Figure 22 Binary entry Switch Sensor behaviour of a switch or sensor connected to the ACTinBOX Classic Hybrid input d Rising edge sets the action to be performed by ACTinBOX Classic Hybrid when it detects a rising edge in the input signal The options are gt No action no action is performed gt 0 ACTinBOX Classic Hybrid will sen
69. times for the switch on and for the switch off of the output http www zennio com Technical Support http zennioenglish zendesk com 6 Zennio ACTinBOX CLASSIC HYBRID AD d Scenes Allows running and or saving a specific action over the output s where this function is enabled The status of the outputs will vary depending on the action set for the parameterized scene d Alarm Allows changing the status of the output where this function is enabled being possible to configure the status the output will be set to both on the alarm activation and on the alarm deactivation Note the alarm behaves with priority over the other functionalities d Start up configuration default or custom All these configuration options are explained in detail in section 3 ETS Parametrization 2 2 SHUTTER CHANNELS The output channels of ACTinBOX Classic Hybrid allow controlling up to 2 different shutter drives or similar window door automated systems Thus it is possible to control the movement of the shutter within the domotic installation d Basic control moving the shutter up down d Precise control precise control of the shutter and the slats for blinds featuring slats Each channel A and B consists of two consecutive individual outputs i e Channel A is made of the individual outputs 1 and 2 while channel B consists of outputs 3 and 4 The first output of every channel sends orders to raise the shutter
70. tput will be switched off Assuming that the output is off the alarm becomes active OX Alarm 1 so the output is switched on While the alarm is not deactivated any action over the output will be ignored After some time t2 the alarm is deactivated OX Alarm 0 which makes the output switch from ON to OFF Before the parameterized cyclical monitoring period 2 minutes ends a new alarm deactivation order arrives so the time count starts again After 2 minutes without receiving further values through the alarm object the alarm will be automatically activated making the output status switch on As before any action over the output will be ignored until the alarm is deactivated See the following figure OX Alarm 1 Automatic Alarm TOX Alarm 0 Activation l OX Alarm 0 Output status e 2 minutes 2 minutes http www zennio com Technical Support http zennioenglish zendesk com 19 Zennio ACTinBOX CLASSIC HYBRID AD gt Response sets the response status of the actuator output when the alarm is activated No change ON OFF Flashing 3 drop down lists are shown to configure the ON Duration the OFF Duration and the number of repetitions of the sequence gt Deactivation two different procedures are provided to deactivate an active alarm Normal depending on what was parameterized under Trigger Value the alarm will be deactivated as soon as the ac
71. tuator receives a 0 or a 1 through the alarm object Frozen this method requires a normal deactivation plus the reception of the value 1 over the OX Unfreeze Alarm object if the latter does not occur the alarm status will still be active This method makes the channel output remain locked even when the alarm situation is over until it is externally or manually enabled gt End reaction when alarm ends this parameter sets the status that will be adopted by the output once the alarm finishes No change ON OFF Last the output returns to the status it had before the alarm d Start up configuration defines the state ON OFF that will be adopted by the outputs when the device recovers from a bus power failure or after an ETS download A default or a custom configuration may be selected Selecting the default configuration will make the output stay off after a partial or complete ETS download while after a bus power failure the status of the output will be the same it had before the failure ON or OFF http www zennio com Technical Support http zennioenglish zendesk com 20 Zennio ACTinBOX CLASSIC HYBRID AD If custom is chosen ETS will show the following window 3 111 ACTinBOX Hybrid AD GENERAL ZE lt lt DUTPUTS gt gt OUTPUT 1 INITIAL STATUS Start up Last saved position y OUTPUT 2 UPDATE P z lt lt THERMOSTAT gt gt s
72. unt 0 65535 Last 128 2 Bytes C W LF 2 bytes Data Entry 3 2 bytes Data Entry 9 001 DPT_Value_Temp 0 00 120 00 Last 7 001 DPT_Value_2_Uncount 0 65535 Last 129 2 Bytes C W LF 2 bytes Data Entry 4 2 bytes Data Entry 9 001 DPT_Value_Temp 0 00 120 00 Last 7 001 DPT_Value_2_Uncount 0 65535 Last 130 2 Bytes C W LF 2 bytes Data Entry 5 2 bytes Data Entry 9 001 DPT_Value_Temp 0 00 120 00 Last 7 001 DPT_Value_2_Uncount 0 65535 Last 131 2 Bytes C W LF 2 bytes Data Entry 6 2 bytes Data Entry 9 001 DPT_Value_Temp 0 00 120 00 Last 7 001 DPT_Value_2_Uncount 0 65535 Last 132 2 Bytes C W LF 2 bytes Data Entry 7 2 bytes Data Entry 9 001 DPT_Value_Temp 0 00 120 00 Last 7 001 DPT_Value_2_Uncount 0 65535 Last 133 2 Bytes C W LF 2 bytes Data Entry 8 2 bytes Data Entry 9 001 DPT_Value_Temp 0 00 120 00 Last 134 1 Bit o CTR 1 001 DPT_Switch 0 1 0 Last LF Function 1 RESULT 1 bit FUNCTION 1 Result 135 1 Bit o CTR 1 001 DPT_Switch 0 1 0 Last LF Function 2 RESULT 1 bit FUNCTION 2 Result 136 1 Bit o CTR 1 001 DPT_Switch 0 1 0 Last LF Function 3 RESULT 1 bit FUNCTION 3 Result 137 1 Bit o CTR 1 001 DPT_Switch 0 1 0 Last LF Function 4 RESULT 1 bit FUNCTION 4 Result 138 1 Bit o CTR 1 001 DPT_Switch 0 1 0 Last LF Function 5 RESULT 1 bit FUNCTION 5 Result 139 1 Byte o CTR 5 010 DPT_Value_1_Uncount 0 255 0 Last LF Function 1 RESULT 1 byte FUNCTION 1
73. z Parameteriz Ox Status 0 Output Off 1 Output ON 10 13 1 Bit C W 1 001 DPT_Switch 0 1 Last Ox Timer 0 to turn Off 1 to turn ON 14 17 1 Bit C W Start stop 0 1 Last Ox Flashing 1 Start Flashing 0 End Flash 18 21 1 Bit C W 1 003 DPT_Enable 0 1 0 Last Ox Block 1 Block 0 Unblock 1 Bit C W 1 5 DPT_Alarm 0 1 Last Ox Alarm 0 Alarm 1 No Alarm weg 1 Bit C W 1 5 DPT_Alarm 0 1 Last Ox Alarm 1 Alarm 0 No Alarm 26 29 1 Bit C W 1 16 DPT_Ack 0 1 0 Last Ox Unfreeze Alarm Alarm 0 Unf 1 gt End Alarm 30 1 Bit C W 1 007 DPT_UpDown 0 1 0 Last CA Move 0 Up Shutter 1 Down Shutter 31 1 Bit C W 1 007 DPT_UpDown 0 1 0 Last CA Reverse Movement 0 Down Shutter 1 Up Shutter 32 1 Bit C W 1 007 DPT_UpDown 0 1 0 Last CB Move 0 Up Shutter 1 Down Shutter 33 1 Bit C W 1 007 DPT_UpDown 0 1 0 Last CB Reverse Movement 0 Down Shutter 1 Up Shutter 1 Bit C W 1 7 DPT_Step 0 1 0 Last CA Stop 0 or 1 Stop Shutter ds 4 Bit C W 1 7 DPT_Step on 0 Last CA Stop Step eege 35 1 Bit C W 1 003 DPT_Enable 0 1 0 Last CA Block 1 Block 0 Unblock 1 Bit C W 1 7 DPT_Step 0 1 0 Last CB Stop 0 or 1 Stop Shutter ki 1 Bit GW 1 7 DPT_Step o 0 Last CB Stop Step oa 37 1 Bit C W 1 003 DPT_Enable 0 1 0 Last CB Block 1 Block 0 Unblock 38 1 Byte o CTR 5 001 DPT_Scaling 0 255 0 Last CA Current Shutter Position 0 0 Top 255 100 Bottom 39 1 Byte o CTR 5 001 DPT_Scaling 0 255 0 Last CB Current S

ACTinBOX CLASSIC HYBRID AD

Contents

Download Pdf Manuals

Related Search

Related Contents