Universal Garage Door Remote Control
Contents
1. position see diagram J Original Position Diagram J If your garage door opener is manufactured by Chamb erlain Sears Lift Master Wayne Dalton or Master Mechanic the switches will have 3 positions 0 Set the connectors on the model G5M to match their corresponding positions If your opener is a Sears Chamberlaine or Lift Master and the existing transmitter has three buttons see diagram K the first connector in the model G5M may need to be changed to another position If your Chamberlaine Sears Lift Master has 9 DIP switches match them to the first 9 connectors on the model G5M and remove the last 3 connectors connectors 10 11 12 If there are only 8 DIP switches on your Chamberlaine Sears Lift Master match them to the 2 9 position on the model G5M and remove the last 3 connectors connectors 10 11 12 2 PROGRAMMING YOUR NEW TRANSMITTER CONT Now you may have to change the positioning of the 1 connector on the model G5M If the large button of Diagram K is used to open the garage door set the 1 connector to position If the middle button is used set the 1 connector tothe 0 or blank position If the smaller button on the left is used s et the 1 connector to the position L c Diagram K 3 OPERATION To operate the model G5M with your GDO properly please press the button on the model GSM NOTE Transmi2. s product or have difficulty getting your Skylink s remote control to work please 1 visit our FAQ section at www skylinkhome com or 2 email us at support skylinkhome com or 3 call our toll free at 1 800 304 1187 from Monday to Friday 9 am to 5 pm EST Fax 800 286 1320 CUSTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y 1J3 Email support skylinkhome com http www skylinkhome com P N 101A396 001 US Patent D380895 5680134 5841390 6005508 6956460 are registered trademarks of their respective corporations 2005 SKYLINK GROUP
3. see diagram F Diagram E Ww Diagram F 4b Set the connectors numbered 1 through 12 to match the code setting of your existing transmitter or receiver There are 2 places you can find out the code setting from a column of small switches of your existing garage door opener 1 your existing transmitter the unit you currently use to open your garage 2 the receiver of your garage door opener the unit with the motor mounted on the ceiling of your garage 2 PROGRAMMING YOUR NEW TRANSMITTER CONT Ac If the connector is placed on the top and 2 or OFF or OPEN middle posts that column is seton gt or ON or CLOSE 0 BLANK or ON or CLOSE If the connector is ee placed on the middle and bottom posts that column is set on or OFF or OPEN If the connector is removed com pletely not placed on any posts it is set to 0 orthe neutral position see diagramG for examples of how to set a column to the three different positions When removing a connector to set a column to the neutral position save the connector in case you change the code at a later date 4d To move the connectors slide an opened paper clip into the side of a connector and lift see diagram H When repositioning connectors place a connector on the two chosen posts then push down on the connector with your finger Diagram H Code connector setting to match your opener
4. these 2 brand jumpers B e ta fas A and B based on the brand jump ers setting Brand Jumper on chart 2 Please identify the group number on chart 2 in order to determine which is the next step to proceed REMOVE JUMPER 0 Diagram C 2 PROGRAMMING YOUR NEW TRANSMITTER CONT For garage door openers belonging to groups 1 to 5 please follow step 3 of the procedures this will complete the setup No need to proceed to step 4 For garage door openers belonging to groups 6 to 0 you can proceed directly to Step 4 Set Code Connector after you have successfully set the brand jumpers Please skip step 3 below Group Brand Brand jumpers setting Proceed to 1 Chamberlain Sears Lift Master without DIP switches but with red orange or purple learn button 2 Chamberlain Lift Master Sears Wayne Dalton Master Mechanic without DIP switches but with yellow white gray or green learn button 3 Genie Intellicode without DIP switches Proceed to Step 3 Overhead Code Dodger without DIP switches 4 5 6 7 a Lift Master oe Wayne Dalton Master Mechanic ith DIP Switches Proceed to Step 4 Step 3 9 Linear Moore O Mai 0 Pulsar Allstar Allister Canada only Chart 2 Note For Genie Intellicode amp Overhead Code Dodger if the brand jumper for group 3 cannot operate your garage door opener properly plea
5. Universal Garage Door Remote Control 1 INTRODUCTION Thank you for your purchase of the Skylink garage door remote control Model G5M There are 3 different steps you need to set up in order to use this universal garage door remote control to operate your existing garage door opener These 3 steps are Model G5M 1 Frequency switch select the correct frequency according to the brand of your existing garage door opener 2 Brand jumpers place the brand jumpers at the correct position according to the brand of your existing garage door opener 3 Code setting Set the jumper connectors on the Model G5M so that they match the code setting of your existing garage door opener In this package you should find a garage door remote control with 12V alkaline battery a mounting bracket and a clip Mounting Bracket Clip Garage Door Remote Control Battery inside Please follow the detailed instructions below in order to set up the Skylink Model G5M to work with your existing opener 2 PROGRAMMING YOUR NEW TRANSMITTER 1 SET FREQUENCY SWITCH 1a Locate frequency switch on the top of the transmitter See diagram A 1b Determine the brand of your garage door opener and set the frequency switch to the corresponding position See chart 1 USA CANADA Set switch Set switch Brand of your opener to position Frequency to position Frequency Chamberlair 390 or 315 315 o
6. motor Linear Position tto8 OR J Posiiontto8 OR Stanley 810 Canada Postion tto10 OR 11 12 setto vor Position 1 to 10 Position 1 to 10 Position 1 to 9 0 blank OR Wayne Dalton Position 1to9 0 blank OR Position 1 to 9 Genie 12 postions Posiionitoi2 OR 0 blank OR Position 1 to 10 11 12 set to Posion 1to9 O blank OR Set the connectors numbered 1 through 12 to match the switches of your existing transmitter or receiver If your garage door opener is manufactured by Stanley Genie Multi Code Lineare Moore O Matice these switches may only have two positions ON CLOSED and OFF OPEN see diagram I Set the connectors on the model G5M to if your existing switches are either ON CLOSE and set to if your existing switches are either OFF OPEN Do not use the blank position 0 Examples of how to set Model G5M Model G5M ORG gt Page HAEA Diagram I Existing Transmitter If your existing transmitter has fewer than 12 switches match only the first corresponding connectors Leave the remaining posts blank remove the connectors Press the button on the transmitter If the garage door does not open reverse all of the connectors on the model G5M The will be changed to the position and the position will be changed to the
7. r 390 Lift Master AorB 390 0r315 CorA 315 or 390 Sears AorB 3900r315 CorA 315 or 390 Wayne Dalton DorA 3000r390 CorA 315 or 390 Master Mechanic A 390 CorA 315 or 390 Genie A 390 CorA 315 or 390 Overhead 390MHz only A 390 A 390 Linear G 310 D 310 M O M Cc 310 D 310 Stanley C 310 D 310 Multi Code Dorc 300 or 310 D 310 Martec Teckey D 300 N A Skylink UR 100 A 390 A 390 Pulsar Allstar Allister N A B 318 Linear MegaCode N A B 318 Skylink 18 series N A B 318 Chart 1 2 SET BRAND JUMPER 2a To set the brand jumpers open the case with a coin see diagram B Diagram B 2b The Model G5M contains 2 brand jumpers and 12 code connectors see diagram C The brand jumpers are located just above the battery with markings A and B There are 2 connectors one is placed on the A column the other one is placed on the B column For each column there is a connector If the connector is placed on the top and middle post of that column that column is set on placed on the middle and bottom posts that column is set on If the connector is removed completely that column is set on 0 see diagram C In order for the Model G5M to work with your existing garage door opener motor you need to set the brand jumpers 7 Code connector Location If the connector is EAEE EAE Eleea Ha C based on the brand of your existing garage ia door opener Please set
8. se use setting A B 3 LEARN CODE Note Proceed to this step only if the brand of your garage door opener belongs to either group 1 2 3 4 or 5 on chart 2 Otherwise proceed to Step 4 Set code connector 3a If your existing garage door opener belongs to any brand from group 1 2 3 40r 5 then you should find a learn button from the garage door opener the unit with the motor located on the ceiling of your garage see diagram D Press this learn button for approximately 2 seconds The LED light beside the learn button will go on and then press the button on the Model G5M to activate it The LED light on the garage door opener will flash then go off The Model G5M is now programmed to your existing garage door opener and will operate your garage door Programming is now completed and please refer to the Battery 7 i section of this manual for battery Learn Button maintenance Garage Door Opener GDO Diagram D 4 SET CODE CONNECTORS Note Proceed to this step only if the brand of your garage door opener belongs to either group 6 7 8 9 or 0 on chart 2 Otherwise proceed to Step 3 Learn code 4a If the brand of your garage door opener belongs to groups 6 to 0 that means you need to program the correct code setting in order for the Model G5M to work with your existing garage door opener There are 12 code connectors on 12 columns from 1 to 12 see diagram E Each column has one connector
9. ssion range may be reduced with use on a metal garage door 4 BATTERY 12 volt alkaline battery size 23A included cal WARNING If this transmitter triggers other garage doors in your neighborhood change all your transmitters and receiver to a new code setting DO NOT let children use the garage door transmitter without adult supervision Children can injure themselves or others by the garage door 6 FCC The Universal Garage Door Remote Control is approved by the FCC and it complies with Part 15 of the FCC Rules Its operation is subject to the f ollowing two conditions 1 This device may not cause harmful interference 2 This device must accept any interference that may cause undesired operation WARNING Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user s authority to operate the equipment 7 WARRANTY If within one year from date of purchase this product should become defective except battery due to faulty workmanship or materials it will be repaired or replaced without charge Proof of purchase and a Return Authorization are required 8 CUSTOMER SERVICE If your Skylink Universal Remote Control does not activate your Garage Door Opener the reason may be that your GDO age or manufacturer is not listed on the compatibility chart The solution is the Skylink SG 18R Universal Receiver If you would like to order Skylink
Download Pdf Manuals
Related Search