Seasafe Transmitter User Manual
Contents
1. SEASAFE MODEL SSTX 01 amp SSTX DV PERSONAL MAN OVERBOARD and LOST DIVER ALARM amp TRACKING TRANSMITTER USER MANUAL WWW Sea safe com au Seasafe SSTX 01 amp SSTX DV Transmitter User Manual Contents Page 1 Technical support 3 2 Warranty 3 3 Regulatory compliance 3 4 Box contents 3 5 Layout 4 6 Equipment introduction 5 7 Equipment specification 5 8 1 Operation SSTX 01 Man Overboard amp Diving to 30 metres Battery Antenna Arm Band amp Belt Clip Optional Dive Cap Man Overboard Operation Lost Diver Operation ooocp NN 8 2 Operation SSTX DV Diving to 40 metres a Lost Diver surface location 8 9 Accessories 8 10 Copyright 8 11 Warranty Registration Certificate 9 1 Technical Support For any technical questions or for support please contact your local Seasafe distributor or visit Internet www sea safe com au Email info sea safe com au Telephone 61 7 3488 2622 2 Warranty Seasafe warrants this product to be free from defects in materials and workmanship for 12 months after the date of purchase If your Seasafe personal transmitter is found to be defective within that time we will promptly repair or replace it This warranty does not cover accidental damage wear and tear or consequential or incidental loss Either complete the warranty form at the back of this manual and hand to your Seasafe dealer or alternatively register your warranty at www sea safe com2. LED should not flash again at this stage When testing the unit ensure that the antenna is NOT attached to the transmitter otherwise the transmitter will activate any Seasafe receivers which may be in range This may cause a false alarm to be received and an unnecessary response to be initiated b Flexible Antenna The Seasafe SSTX 01 amp SSTX DV transmitters are supplied with a screw on flexible antenna Prior to use the antenna should be securely screwed onto its mounting position at the top of the transmitter Be sure not to over tighten the antenna on to its mounting post The length of the antenna is extremely important to the operation of the transmitter If the antenna were to be lengthened or shortened in any way the transmitter would cease to operate correctly Care should also be taken not bend the antenna unnecessarily c Attaching the transmitter to your body The transmitter is provided with a number of mounting options Included in the box with the transmitter is a belt clip and an arm band mounting adapter Your transmitter purchase also includes not supplied in the box an ergonomic adjustable arm band The belt clip and arm band mounting adapter are interchangeable On the back of the transmitter are two stainless steel screws Depending whether you require the belt clip or arm band simply remove the two mounting screws place the mounting of your choice in position and re insert the two screws The belt clip ma
3. cap must be firmly installed over the bottom of the transmitter ensuring that there is a firm seal and that the cap is installed the correct way round Looking at the front of the transmitter the pull ring on the dive cap should be on the right hand side See diagram below The Seasafe transmitter with fitted dive cap should be secured to an appropriate place on your person so it is easily accessible Generally securing it by means of the belt webbing clip to the BCD is a good option Should you require assistance or find yourself in distress whilst underwater remove the dive cap by pulling firmly on the dive cap pull ring This will expose the water activation sensors to the water and the transmitter will activate The flashing red LED will begin to flash This should act as an indicator to anyone diving in close proximity that you require attention The radio frequency signal will not transmit through water and the dive boat will only receive an alarm once you and the antenna break the surface of the water It is also recommended that once you have broken surface you should manually activate the transmitter by depressing the On Off button according tho the manual activation procedure mentioned above signal transmission is indicated by flashing red LED This will ensure that the device continues to transmit even if it is not permanently immersed in the water Once you have been recovered by the dive vessel you should immediately deactivate your trans
4. au 3 Regulatory Compliance This device complies with AS 4268 2 as amended by LIPD Low Interference Potential Device 24 August 2005 In particular table ZZ1 Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including any interference that may cause undesired operation i N15546 1999 5 EC ETSI EN 300 220 2 ETSI EN 300 220 1 ETSI 301 489 1 ETSI EN 301 489 3 EN 61000 3 2 EN 6100 3 3 5 4268 2 4 Box Contents Included in the purchase of the Seasafe SSTX 01 amp SSTX DV Personal Alarm amp Tracking Transmitter are the following components Seasafe Model SSTX 01 or DV Personal Alarm amp Tracking Transmitter Antenna e 1x CR123A Lithium battery 1x Arm Band mounting adapter 1x interchangeable belt clip 1x ergonomic arm band Not in box e Instruction manual Antenna Battery Arm Band mounting adapter ON OFF Belt Clip Personal Transmitter Seasafe SSTX 01 amp SSTX DV Transmitter Box Contents Ergonomic Arm Band is not supplied in the box but is supplied as part of the kit 5 5 easafe Model SSTX 01 Personal Transmitter Lay out amp Controls Personal Transmitter Front ON OFF Arm Band Arm Band mounting adapter Manual On Off Button Flexible Antenna Clear Lens with Flashing Red LED when activat
5. circuit has been designed so as not to activate the transmitter in the event that it is exposed to rain and or wave splashes normally associated with marine activities If you fall overboard or you are knocked unconscious overboard after 5 seconds in the water with the water activation sensors immersed the transmitter will switch on and begin transmitting a signal Any Seasafe receiver within range will receive an alarm and can begin tracking your signal immediately If you are conscious and able to it is recommended that you also manually activate the transmitter by pushing the On Off button as described in the manual activation procedure above This will ensure that the device continues to transmit even if it is not immersed in the water all of the time Once you have been rescued or if you no longer require assistance the transmitter should be switched off by firmly depressing the On Off button for 1 second if you have also manually activated the device or by drying off the water sensors if the device has been automatically activated This will ensure that persons involved in the search will know that their service is no longer required At the first available opportunity the battery in your Seasafe transmitter should be replaced with a new one f Lost Diver Operation In order to use the Seasafe transmitter for underwater or diving applications you need to purchase an optional rubber dive cap Before you enter the water the dive
6. ed Adjustable arm strap oOanran Personal SSTX 01 Transmitter Bottom us m 1 Automatic Water Activation Sensors Personal SSTX 01 Transmitter Back Flexible Antenna Arm Band Mounting Adapter Belt Clip mounting screws Battery Compartment Cover Battery Compartment Cover Screws Antenna Mounting post Qe Equipment Introduction Congratulations on your purchase of the Seasafe SSTX 01 or SSTX DV Personal Alarm and Tracking Transmitter Used in conjunction with the Seasafe SSRX 01 Alarm amp Tracking Receiver the Seasafe system represents a major breakthrough in personal tracking and location technology Please remember that the Seasafe system is an Aid to rescue only and DOES NOT guarantee your safety This at all times remains the responsibility of the individual Before using the Seasafe system is important that you ensure the equipment complies with any or all standards and regulations which may pertain to the prospective country s in which you intend to use the system The Seasafe system is a stand alone and self contained Alarm Tracking amp Location system It operates independently of traditional EPIRB satellite and International Emergency Frequency based systems Seasafe allows non critical and critical situations to be responded to immediately at the time and place at which they occur The system is not reliant on a response from National or International Search amp Rescue Authorities and allows a re
7. iving to 30 metres The Seasafe SSTX 01 is a personal tracking and location device which works on a transmitted radio frequency signal in conjunction with the SSRX 01 Tracking and Location receiver The transmitter can be used in ANY land or marine based activity whereby a person may become lost in distress or requiring medical attention The distance over which the transmitter signal may be received is dependent on a number of factors including but not limited to prevailing weather conditions sea state wave height line of sight obstructions and cloud cover Generally the higher the transmitter is above the ground the longer the transmitted range The same principle applies to the height of the receiver antenna a Battery Important Information Upon purchase of the SSTX 01 and SSTX DV and prior to use the included Lithium battery should be installed into the device The four battery cover securing screws should be carefully removed and the battery should be inserted into the battery compartment Utmost care should be made to install the battery the correct way round The ve side of the battery should match the markings in the battery compartment and the same with the ve markings Once the battery has been inserted the battery compartment cover should be carefully screwed back in place making sure the rubber o ring is in place and taking care to tighten the screws beginning at one corner and then tightening the opposite corner
8. ld be manually activated by using the manual ON OFF button In order to activate the transmitter the button should be pressed twice for approximately half a second each time within a five second time frame The red flashing LED will indicate that the device is transmitting Once a diver has been recovered the device should be de activated by holding down the ON OFF button for approximately one second The red LED will flash quickly several times and then cease to flash At the earliest opportunity the transmitter should be returned to an authorised Seasafe dealer for battery replacement The rest of the specifications of this device are identical to the Model SSTX 01 transmitter Accessories a Dive Cap The optional rubber Dive Cap is for use in underwater applications or in marine activities where it is expected that the transmitter may be exposed to large volumes of water which may inadvertedly activate the device through the water activation sensors If used with the dive cap the transmitter is UNABLE to automatically activate and must be manually activated Before use ensure that the dive cap is fitted firmly and the correct way round If it is not fitted correctly water may enter the dive cap and the transmitter will activate Copyright Copyright Seasafe Pty Ltd 2007 International Patents Pending Specification subject to change without notice
9. mitter by depressing the On Off button for 1 second indicated by two quick flashes of the red LED The battery in your transmitter should be replaced at the earliest opportunity The dive cap may be attached to the transmitter by means of a lanyard connected to the eye on the dive cap and one of the spare holes either on the belt clip or arm band adapter This will ensure that you do not lose the dive cap in the event that you remove it in an emergency Similarly the transmitter can be also be attached to your body by means of a lanyard if required 7 The Seasafe SSTX 01 transmitter is only recommended for use down to a maximum of 30 metres underwater and is not guaranteed for use below this depth Pull Ring for quick dive cap removal and transmitter activation under water Eye for attachment of lanyard ON 8 9 Rubber Dive Cap for under water applications Transmitter with Dive Cap fitted SYSTEM OPERATION Model SSTX DV SUITABLE FOR DIVING TO 40 METRES a Lost Diver Surface Location The SSTX DV has been developed specifically for scuba diving applications This model transmitter can NOT be used for Man Overboard applications and does not make use of automatic water activation sensors The transmitter may only be manually activated and only once the diver has reached the surface In the event of a diver surfacing out of sight of the dive vessel or if a diver is in need of assistance the transmitter shou
10. screw Continue to tighten opposite screws until all four are tightly secured Failure to tighten the screws in this sequence may result in the compartment not sealing correctly This may allow moisture into the transmitter which will render it un operational The battery compartment is sealed through the use of black rubber O ring You must ensure that the O ring is correctly seated into its groove If at any time the O ring appears brittle cracked or not in perfect condition a replacement should be obtained from your nearest Seasafe dealer and installed It is recommended that you return your SSTX 01 transmitter to an authorised dealer for battery replacement This will ensure that the battery is correctly installed and the o ring inspected and or replaced if necessary The battery must be replaced with a new one at least every three years This will ensure that the battery is always in a fully charged condition If the transmitter has been activated for any length of time during the three year period it MUST be replaced immediately Once the battery has been installed you may test the transmitter by depressing the On Off switch TWICE in succession for approximately half a second each time within a 5 second timeframe until the red LED begins to flash The transmitter should then be immediately turned off by again by depressing the On Off switch for approximately 1 second until the red LED flashes several times in quick succession The
11. sponse to be undertaken immediately an emergency occurs The Seasafe system may be used in any marine or land based pursuit whereby a person may become lost disorientated or in need of assistance Equipment Specification Erequency d ssec bebe ERR GENERE ARTE 173 4875 MHz DIMENSIONS esie meia 80mm x 78mm W x 32mm D Weight with rere o vases ER TERREA A 250g Temperature 10 C to 455 C Frequency Stability 15 PPM Transmitter 60 Milliwatts nominal at antenna terminal Radiated POWOer ei ime date RR Approx 8 Milliwatts Modulation QU E UU UT 3 KHz Water resistance Model SSTX 01 Maximum 30 metres underwater Water resistance Model Maximum 40 metres under water Spurious 0 1 uW 40 DBM Power 3VDC Lithium cell C Tick compliance registration N15546 Australia New Zealand AS 4268 2 European CE 1999 5 EC 8 1 Operation Model SSTX 01 Suitable for Man Overboard Operation and D
12. the underside of the body of the device When both these sensors have been submerged in water for approximately 5 seconds the transmitter will switch on and begin transmission of signal Automatic activation is designed as a mechanism to switch the device on in the event of a person falling overboard in an unconscious state If it is intended that the Seasafe transmitter is to be used for underwater diving purposes then an optional rubber Dive must be purchased Use of the dive cap ensures that the device will not be unintentionally activated when submersed under water during the course of underwater activities The dive cap serves the purpose of isolating or sealing the automatic water activation sensors from the water If it is necessary to activate the device when using the dive cap then it should be removed by firmly pulling the pull ring until the cap is fully removed from the bottom of the transmitter If the transmitter has been automatically activated through immersion of the water activation sensors it is not possible to switch the device off by using the manual on off button The device will stop transmitting once the water sensors are removed from the water and are dry e Man Overboard Operation If you intend to use the device as a Man Overboard alarm once on board the vessel the transmitter should be attached to your body using one of the methods described above The transmitter automatic activation
13. y be mounted in either the vertical or horizontal planes depending how you intend to wear the device If using the arm band mount the arm band adapter to the back of the transmitter and then attach the transmitter to the arm band The arm band may be loosened or tightened by adjusting the clip straps on the arm band The arm band mounted transmitter should be worn on the upper arm bicep In this position if a person falls in the water and assuming they are wearing a life jacket the device will be in the most appropriate position for a portion of the antenna to protrude above the water and to transmit a signal The device will NOT transmit a signal if the antenna is under the water When using the belt or webbing clip the device should be worn in a position which will provide the best opportunity for the antenna to protrude above the water in the event that a person falls overboard Both the belt clip and arm band adapter have additional holes which may be used for attaching a lanyard to a life jacket or other part of your person Seasafe Transmitter fitted Rear view of transmitter showing Side view of transmitter to Arm Band Arm Band mounting adapter showing belt clip d Optional Dive Cap The Seasafe transmitter may be automatically activated upon submersion in water or manually activated by depressing the On Off button The transmitter is automatically activated through the submersion of two metallic water activation sensors on
Download Pdf Manuals
Related Search