Home

CrossBow

1. Rest the Backrest against the Upright 3 For row exercises and for using the Leg Lever 7 remove the Backrest 14 from the Seat Carriage 12 Hold the Backrest vertically over the Seat 13 and lift the rod out of the slot in the Seat Carriage see the inset drawing To use the Leg Lever 7 secure the Seat Carriage 12 at the second hole from the Leg Developer STORING THE RESISTANCE SYSTEM To store the resistance system slide the ends of the Leg Lever Cable 32 onto the Hook 104 Be sure Crossbows the Seat 13 is in the position closest to the Front Leg 6 see ADJUSTING THE SEAT on page 13 Next remove the Storage Knob 30 from the Upright U Channel 3 Lift the Front Leg toward the Lat Tower Crossbar 10 and tighten the Storage Knob into the side of the Upright and the Bench Rail Remove all of the crossbows from the U channels on the 10 pound centre Crossbow 44 see ADJUSTING THE RESISTANCE on page 14 Finally loosen the Fulcrum Knob 43 and pull it out as far as it will go Turn the crossbow assembly vertically and engage the Fulcrum Knob into the fulcrum on the Lat Tower 4 Note Storing the crossbows vertically will prolong the life of the crossbows To move the resistance system place the toe of your shoe on the end of the Base 1 and hold the resist ance system in the indicated area Tilt the resistance system back onto the Wheels 31 and roll it to the new location Be careful not to
2. 23 and the Cross Tube to the Upright 3 with two M10 x 143mm Carriage Bolts 73 two M10 Washers 75 and two M10 Nuts 47 Do not insert a bolt into the top hole in the Foot Plate yet 4 Press two 57mm Round Outer Caps 27 onto the ends of the Front Leg 6 Orient the Bench Rail 5 as shown Slide the Rail Bracket 105 into the indicated end of the Bench Rail and align the holes in the Bracket with the holes in the Bench Rail Orient the Front Leg 6 as shown Attach the Front Leg to the Bench Rail 5 with the Rail Bracket 105 four M8 x 25mm Button Screws 46 and four M8 Split Washers 52 5 See the inset drawing Snap the Seat Knob 45 into the Seat Carriage 12 and attach it with two M6 x 16mm Screws 82 and two M6 Black Nylon Locknuts 69 Make sure the slot in the Knob is aligned with the slot in the Seat Carriage Orient the Seat 13 and Seat Backing 9 as shown Attach the Seat and Seat Backing to the Seat Carriage 12 with four M6 x 16mm Screws 82 ADJUSTING THE BACKREST The Backrest 14 can be used in a level position or one of three inclined positions To use the Backrest in a level position secure the Seat Carriage 12 at the hole in the Bench Rail 5 closest to the Leg Developer 19 see ADJUSTING THE SEAT on page 13 To use the Backrest 14 in an inclined position secure the Seat Carriage 12 at one of the three adjustment holes on the Upright 3 side of the Bench Rail 5
3. a 19mm Spacer 17 a 22mm Spacer 106 and an M10 Nylon Locknut 76 Do not over tighten the Locknut the Bench Rail must be able to pivot easily Fully tighten the Storage Knob 30 into the Upright 3 and Bench Rail 5 Attach the Lat Tower 4 to the Upright 3 with four M10 x 25mm Button Head Screws 87 and four M10 Split Washers 103 Attach the Name Plate 89 to the Lat Tower 4 with two M4 x 16mm Screws 62 9 Press two 38mm Round Inner Caps 38 into the ends of the Lat Tower Crossbar 10 Attach two Eyebolts 34 to the Lat Tower Crossbar 10 with two M8 Washers 59 and two M8 Nylon Locknuts 65 Do not overtighten the Locknuts the Eyebolts must be able to rotate freely Attach the Lat Tower Crossbar 10 to the Lat Tower 4 with two M10 x 65mm Button Head Screws 70 two M10 Washers 75 and the Crossbar Cover 93 Be sure that the Eyebolts 34 are oriented as shown in the inset draw ing If they are not turn the Lat Tower Crossbar around and reattach it 10 Attach the two 10 pound Short Crossbow Caps 20 to the 10 pound centre Crossbow 44 with two M4 x 12mm Flat Head Screws 85 Using ten M4 x 12mm Flat Head Screws 85 attach the two 10 pound Crossbow Caps 101 to the 10 pound Removable Crossbow 67 the two 20 pound Crossbow Caps 88 to the 20 pound Removable Crossbow 36 the four 80 pound Crossbow Caps 100 to the two 80 pound Crossbows 95 and the two 40 pound Crossbow
4. 65 3 M8 Nylon Locknut 8 1 Backrest Backing 66 1 M10 x 132mm Bolt 9 1 Seat Backing 67 1 10 pound Removable Crossbow 10 1 Lat Tower Crossbar 68 2 Long Handle 11 1 Cross Tube 69 2 M6 Black Nylon Locknut 12 1 Seat Carriage 70 2 M10 x 65mm Button Head Screw 13 1 Seat 71 6 M10 x 47mm Button Head Bolt 14 1 Backrest 72 1 Crossbow Cover Plate 15 1 Backrest Frame 73 2 M10 x 143mm Carriage Bolt 16 1 Backrest Cap 74 4 Pivot Bushing 17 1 19mm Spacer 75 10 M10 Washer 18 1 Crossbow Fulcrum 76 20 M10 Nylon Locknut 19 1 Leg Developer 77 6 M6 Shoulder Bolt 20 2 10 pound Short Crossbow Cap 78 4 19mm Round Inner Cap 21 2 High Pulley Housing 79 2 40 pound Crossbow Cap 22 2 Swivel Arm 80 1 Long Cable 23 1 Foot Plate 81 2 M10 x 108mm Bolt 24 2 M10 x 102mm Button Head Bolt 82 12 M6 x 16mm Screw 25 4 Arm Bushing 83 2 M10 x 66mm Carriage Bolt 26 4 Foam Pad 84 1 Fulcrum Endcap 27 2 57mm Round Outer Cap 85 12 M4 x 12mm Flat Head Screw 28 9 90mm Pulley 86 2 M8 x 19mm Button Head Screw 29 14 Pulley Cover 87 4 M10 x 25mm Button Head Screw 30 1 Storage Knob 88 2 20 pound Crossbow Cap 31 2 Wheel 89 1 Name Plate 32 1 Leg Lever Cable 90 6 11mm Spacer 33 2 Short Cable 91 1 Retainer Ring 34 2 Eyebolt 92 1 V pulley 35 1 Crossbow Spacer 93 1 Crossbar Cover 36 1 20 pound Removable Crossbow 94 2 Pulley Housing 37 2 Fulcrum Bushing 95 2 80 pound Crossbow 38 2 38mm Round Inner Cap 96 1 40 pound Crossbow 39 1 Bench Rail Bracket 97 1 M10 x 107mm Bolt 40 1 M10 x 116mm Button Head B
5. Caps 79 to the 40 pound Crossbow 96 11 Locate the Crossbow Fulcrum 18 on the Lat Tower 4 see the inset drawing Slide the Crossbow Spacer 35 onto the rods on the Crossbow Fulcrum Make sure the Spacer is oriented as shown in the drawing Set the Crossbows into the Crossbow Spacer 35 in the following order the 10 pound Removable Crossbow 67 the 20 pound Removable Rinas on Crossbow 36 an 80 pound Crossbow 95 the ie d 10 pound centre Crossbow 44 an 80 pound Crossbow 95 and the 40 pound Crossbow 96 Make sure the indicated rings are on the side shown and the arrows point toward the Spacer Attach the Crossbow Cover Plate 72 with the edges up to the Crossbow Spacer 35 with two M8 x 19mm Button Head Screws 86 ADJUSTMENTS This section explains how to adjust the resistance system See the EXERCISE GUIDELINES on page 17 for important information about how to get the most benefit from your exercise program Also refer to the accompa nying exercise guide to see the correct form for each exercise Make sure all parts are properly tightened each time you use the resistance system Replace worn parts immedi ately The resistance system can be cleaned with a damp cloth and a mild non abrasive detergent Do not use solvents The crossbows can be cleaned with a vinyl and rubber protectant available at an automotive or depart ment store ATTACHING THE HIGH PULLEYS AND LEG LEVER To use a high pulle
6. week to give your body time to regenerate The combination of strength training and aerobic exer cise will reshape and strengthen your body plus devel op your heart and lungs 17 PERSONALISING YOUR EXERCISE PROGRAM Determining the exact length of time for each workout as well as the number of repetitions or sets completed is an individual matter It is important to avoid overdo ing it during the first few months of your exercise pro gram You should progress at your own pace and be sensitive to your body s signals If you experience pain or dizziness at any time whilst exercising stop imme diately and begin cooling down Find out what is wrong before continuing Remember that adequate rest and a proper diet are important factors in any exercise pro gram WARMING UP Begin each workout with 5 to 10 minutes of stretching and light exercise to warm up Warming up prepares your body for more strenuous exercise by increasing circulation raising your body temperature and deliver ing more oxygen to your muscles WORKING OUT Each workout should include 6 to 10 different exercis es Select exercises for every major muscle group emphasising areas that you want to develop most To give balance and variety to your workouts vary the exercises from session to session Schedule your workouts for the time of day when your energy level is the highest Each workout should be followed by at least one day of rest Once you find t
7. AWARNING When adding resist ance make sure that both ends of the cross bow rest under the two U channels The rings on the Removable Crossbows 36 67 must be pushed against the Crossbow Spacer 35 Do not add or remove crossbows from the U channels whilst an end of the Long Cable 80 is pulled out Note The resistance system uses progressive resist ance As the crossbows begin to bend the amount of resistance will increase gradually As the crossbows bend further the resistance will increase rapidly Note 1 pound 0 454 kilograms 14 Crossbows Pull the Seat Knob 45 not shown out as far as it will go and slide the Seat Carriage 12 onto the Bench Rail 5 Engage the Seat Knob into the third hole from the end of the Bench Rail See the inset drawing Attach a Hook 104 to the bottom of the Bench Rail 5 Press the two Rail Inner Caps 99 with the wide ends on the top or bottom as indicated into the ends of the Bench Rail 5 Attach the Caps with four M4 x 16mm Screws 62 Locate the Leg Lever Cable 32 which has three ends connected in the middle with a brack et Route the end of the Cable with the eyebolt under a V pulley 92 Attach the V pulley to Eyebolt the Front Leg 6 with an M10 x 107mm Bolt 97 and an M10 Nylon Locknut 76 Slide the other two ends of the Cable onto the Hook 104 Attach the Bench Rail 5 to the Upright 3 with an M10 x 132mm Bolt 66
8. Housing 21 with an M10 x 47mm Button Head Bolt 71 and an M10 Nylon Locknut 76 Make sure the small tabs on the Pulley Covers are in the indicated position Repeat this step with the other Short Cable 33 12 Press two 25mm Square Inner Caps 54 into the indicated end of the Backrest Frame 15 Attach a Plastic Foot 53 to the Backrest Frame 15 with an M4 x 16mm Screw 62 Orient the Backrest 14 and the Backrest Backing 8 as shown Attach the Backrest and the Backrest Backing to the Backrest Frame 15 with four M6 x 45mm Screws 58 24 Make sure that all parts have been properly tightened The use of the remaining parts will be explained in ADJUSTMENTS beginning on the following page Before using the resistance system pull the long cable a few times to be sure that it moves smoothly over the pulleys If the cable does not move smoothly find and correct the problem IMPORTANT If the cables are not properly installed they may be damaged when heavy resistance is used See the CABLE DIAGRAM on page 16 for proper cable routing 12 13 14 Insert the rod on the Backrest Frame 15 into the slot in the Seat Carriage 12 Hold the Backrest Frame vertically over the Seat Carriage and slide the rod into the slot as shown in the inset drawing Press two 50mm Round Inner Caps 57 into the top and bottom of the Leg Developer 19 Press two 45mm Round Inner Caps 56 into the top and bottom of the Le
9. ORDERING REPLACEMENT PARTS To order replacement parts contact the ICON Health amp Fitness Ltd office or write ICON Health amp Fitness Ltd Customer Service Department Unit 4 Revie Road Industrial Estate Revie Road Beeston Leeds LS118JG UK Tel 08457 089 009 Outside the UK 0 444 113 387 7133 Fax 0 444 113 387 7125 To help us assist you please be prepared to give the following information The MODEL NUMBER of the product WEEVSY59430 The NAME of the product CrossBow by WEIDER LEGEND resistance system The SERIAL NUMBER of the product see the front cover of this manual The KEY NUMBER and DESCRIPTION of the part s see the PART LIST and EXPLODED DRAWING in the centre of this manual Part No 200573 RO903A Printed in China 2003 ICON Health amp Fitness Inc Model No WEEVSY59430 Serial No Write the serial number in the space above for future reference Serial Number Decal under seat QUESTIONS As a manufacturer we are com mitted to providing complete customer satisfaction If you have questions or if there are missing or damaged parts please call 08457 089 009 Or write ICON Health amp Fitness Ltd Unit 4 Revie Road Industrial Estate Revie Road Beeston Leeds LS11 8JG UK email csuk iconeurope com Class HC Fitness Product A CAUTION Read all precautions and instruc tions in this manual before using this equipment Save this manual for f
10. e sit up A set is a series of repetitions The proper amount of resistance for each exercise depends upon the individual user You must gauge your limits and select the amount of resistance that is right for you Begin with 3 sets of 8 repetitions for each exercise you perform Rest for 3 minutes after each set When you can complete 3 sets of 12 repetitions without difficulty increase the amount of resistance Toning You can tone your muscles by pushing them to a mod erate percentage of their capacity Select a moderate amount of resistance and increase the number of rep etitions in each set Complete as many sets of 15 to 20 repetitions as possible without discomfort Rest for 1 minute after each set Work your muscles by com pleting more sets rather than by using high amounts of resistance Weight Loss To lose weight use a low amount of resistance and increase the number of repetitions in each set Exercise for 20 to 30 minutes resting for a maximum of 30 seconds between sets Cross Training Cross training is an efficient way to get a complete and well balanced fitness program An example of a bal anced program is e Plan strength training workouts on Monday Wednesday and Friday e Plan 20 to 30 minutes of aerobic exercise such as running on a treadmill or riding on an elliptical or exercise bike on Tuesday and Thursday e Rest from both strength training and aerobic exercise for at least one full day each
11. ess two 50mm Square Inner Caps 98 into the Base 1 Attach two Plastic Feet 53 and two Large Plastic Feet 102 to the Base 1 with four M4 x 16mm Screws 62 Attach the Upright 3 to the Base 1 with two M10 x 66mm Carriage Bolts 83 two M10 x 72mm Bolts 64 and four M10 Nylon Locknuts 76 as shown Note This step will be easier to complete if the Upright and Base are tipped on their sides Tighten all parts as you assemble them unless instructed to do otherwise e As you assemble the resistance system make sure all parts are oriented as shown in the draw ings The included hex keys and the following tools not included are required for assembly two adjustable spanners one rubber mallet one standard screwdriver one Phillips screwdriver e lubricant such as grease or petroleum jelly and soapy water Assembly will be more convenient if you have a socket set a set of open end or closed end span ners or a set of ratchet spanners 2 Attach a Wheel 31 to the outside of the Base 1 with an M10 x 108mm Bolt 81 three M10 Washers 75 and an M10 Nylon Locknut 76 Do not overtighten the Nylon Locknut the Wheel must be able to turn easily Attach the other Wheel not shown in the same manner 3 Press a 38mm x 64mm Inner Cap 41 into each end of the Cross Tube 11 Orient the Cross Tube 11 as shown with the welded tubes at the bottom Attach the Foot Plate
12. ey Covers are in the indicated position Attach a Pulley Housing 94 to the indicated U channel on the 10 pound centre Crossbow 44 with an M10 x 102mm Button Head Bolt 24 two Pivot Bushings 74 and an M10 Nylon Locknut 76 Wrap the Long Cable 80 over a 90mm Pulley 28 Attach the Pulley and a pair of Pulley Covers 29 inside of the Pulley Housing 94 with an M10 x 47mm Button Head Bolt 71 and an M10 Nylon Locknut 76 Make sure the small tabs on the Pulley Covers are in the indicated position 19 20 21 22 Wrap the Long Cable 80 under a 90mm Pulley 28 as shown Attach the Pulley and a pair of Pulley Covers 29 to the Upright 3 with an M10 x 116mm Button Head Bolt 40 and an M10 Nylon Locknut 76 Make sure the small tabs on the Pulley Covers are in the indicated posi tion Attach a Pulley Housing 94 to the indicated U channel on the 10 pound centre Crossbow 44 with an M10 x 102mm Bolt 24 two Pivot Bushings 74 and an M10 Nylon Locknut 76 Wrap the Long Cable 80 around a 90mm Pulley 28 Attach the Pulley and a pair of Pulley Covers 29 inside of the Pulley Housing 94 with an M10 x 47mm Button Head Bolt 71 and an M10 Nylon Locknut 76 Make sure the small tabs on the Pulley Covers are in the indicated position Wrap the Long Cable 80 around a 90mm Pulley 28 Attach the Pulley and a pair of Pulley Covers 29 to the indicated M10 x 143mm Carriage Bo
13. g Lever 7 Lubricate an M10 x 69mm Bolt 60 with grease Attach the Leg Lever 7 to the Leg Developer 19 with the Bolt and an M10 Nylon Locknut 76 Do not overtighten the Locknut the Leg Lever must be able to pivot easily Press two 19mm Round Inner Caps 78 into the tube on the Leg Lever 7 Slide two Foam Pads 26 onto the tubes Repeat with the tube on the Leg Developer 19 15 16 17 18 Slide the Leg Developer 19 into the Bench Rail 5 Align the hole in the Leg Developer with a hole in the Front Leg 6 Tighten the Bench Knob 42 into the hole in the Leg Developer Connect the eyebolt on the Leg Lever Cable 32 to indicated side of the Leg Lever 7 with an M8 Nylon Locknut 65 Locate the Long Cable 80 Insert one end of the Cable through the welded tube on the Cross Tube 11 If necessary use the tip of a screwdriv er to pull the end of the Cable out of the Swivel Arm 22 Make sure the Cable is on the indi cated side of the welded rod in the Swivel Arm Wrap the Long Cable 80 around a 90mm Pulley 28 Attach the Pulley and the Half Pulley Cover 109 to the inside of the Swivel Arm 22 with an M10 x 47mm Button Head Bolt 71 and an M10 Nylon Locknut 76 Wrap the Long Cable 80 around a 90mm Pulley 28 Attach the Pulley and a pair of Pulley Covers 29 to the indicated M10 x 143mm Carriage Bolt 73 with an M10 Nylon Locknut 76 Make sure the small tabs on the Pull
14. he schedule that is right for you stick with it EXERCISE FORM Maintaining proper form is an essential part of an effective exercise program This requires moving through the full range of motion for each exercise and moving only the appropriate parts of the body Exercising in an uncontrolled manner will leave you feeling exhausted On the exercise guide accompany ing this manual you will find photographs showing the correct form for several exercises and a list of the muscles affected Refer to the muscle chart on page 18 to find the names of the muscles The repetitions in each set should be performed smoothly and without pausing The exertion stage of each repetition should last about half as long as the return stage Proper breathing is important Exhale during the exertion stage of each repetition and inhale during the return stroke Never hold your breath USING THE REMOVABLE CROSSBOWS The Removable Crossbows 36 67 can be used to exercise apart from the resistance system as shown in the video or on the exercise guide To remove a Crossbow pull it out of the Crossbow Spacer 35 To replace the Removable Crossbows 36 67 slide them into the Crossbow Spacer 35 from the side shown so that the arrows on the rings point toward the Crossbow Spacer Make sure the rings are pushed against the Crossbow Spacer ADJUSTING THE LEG DEVELOPER To adjust the height of the Leg Developer 19 remove the Bench Knob 42 from
15. ions com pleted Record your weight and key body measure ments at the end of every month Remember the key to achieving the greatest results is to make exercise a regular and enjoyable part of your everyday life MUSCLE CHART Sternomastoid neck Pectoralis Major chest Biceps front of arm Obliques waist Brachioradials forearm Hip Flexors upper thigh Abductor outer thigh Quadriceps front of thigh Sartorius front of thigh 18 Tibialis Anterior front of calf Soleus front of calf Anterior Deltoid Shoulder Rectus Abdominus stomach Adductor inner thigh Trapezius upper back Rhomboideus upper back Deltoid shoulder Triceps back of arm Latissimus Dorsi mid back Spinae Erectors lower back Gluteus Medius hip Gluteus Maximus buttocks Hamstring back of leg Gastrocnemius back of calf A B C D E F G H l J K L M N O P Q R S T U V W X IMPORTANT PRECAUTIONS AWARN ING To reduce the risk of serious injury read the following important precautions before using the resistance system 1 Read all instructions in this manual before using the resistance system Use the resist ance system only as described in this manual 2 Itis the responsibility of the owner to ensure that all users of the resistance system are adequately informed of all precautions 3 The resistance system is intended for home use only Do not use the resistance sy
16. let the Front Leg 6 or Leg Lever 7 pinch your hands when you tilt the system back AWARNING Be sure that all of the crossbows are removed from the U channels before moving the crossbow assembly to the stored position Make sure that the crossbow assembly is in the horizontal position and that the Storage Knob 30 is in place and fully tightened each time the resistance system is used 15 ATTACHING THE ACCESSORIES To attach a Short Handle 49 to a high pulley first attach the high pulley to the resistance system see ATTACHING THE HIGH PULLEYS AND LEG LEVER on page 13 Then attach the Short Handle to the Short Cable 33 with a Cable Clip 51 The Long Handles not shown and the Ankle Strap not shown can be attached to the Long Cable 80 with Cable Clips 51 Attach the Leg Press Strap not shown to both ends of the Long Cable or the optional lat bar to the Short Cables 33 with two Cable Clips ADJUSTING THE RESISTANCE To add resistance hold a U channel on the 10 pound centre Crossbow 44 firmly and push the end of a crossbow under it Repeat with the other end of U Channel the crossbow If more resistance is needed add one crossbow at a time Note When adding resistance always start with the heaviest crossbow to be used and finish with the lightest crossbow When removing crossbows from the U channels start with the lightest crossbow and finish with the heaviest
17. lt 73 with an M10 Nylon Locknut 76 Make sure the small tabs on the Pulley Covers are in the indicated position Make sure there are no Crossbows not shown under the U channels on the 10 pound centre Crossbow not shown Have a second person pull on the Long Cable 80 to create slack in the Cable Insert the end of the Long Cable 80 through the welded tube on the Cross Tube 11 If necessary use the tip of a screwdriver to pull the end of the Cable out of the Swivel Arm 22 Make sure the Cable is on the indicated side of the welded rod in the Swivel Arm Wrap the Long Cable 80 around a 90mm Pulley 28 Attach the Pulley and the Half Pulley Cover 109 inside of the Swivel Arm 22 with an M10 x 47mm Button Head Bolt 71 and an M10 Nylon Locknut 76 11 N77 M6 x 45mm Screw 58 M10 Nut 47 Ay OH O M10 x 47mm Button Head Bolt 71 M8 Nylon Locknut 65 M10 Nylon Locknut 76 E D M10 x 65mm Button Head Screw 70 M10 x 25mm Button Head Screw 87 M10 x 69mm Bolt 60 AND CUM O i C M6 Black Nylon Locknut 69 M8 x 25mm Button Head Screw 46 M10 x 66mm Carriage Bolt 83 M8 x 19mm Button M10 x 72mm Bolt 64 Head Screw 86 MM M10 x 102mm Button Head Bolt 24 M6 x 16mm Screw 82 _ eK AN o M10 x 107mm Bolt 97 M4 x 16mm Screw 62 a
18. ng A a M4 x 12mm Flat M10 x 108mm Bolt 81 EN i M10 x 116mm Button Head Bolt 40 ANN UON M10 x 143mm Carriage Bolt 73 PART IDENTIFICATION CHART Refer to the drawings below to identify small parts used in assembly The number in parentheses below each drawing is the key number of the part from the PART LIST on the reverse side of this page Note Some small parts may have been pre attached If a part is not in the parts bag check to see if it has been pre attached OL Or M8 Split Washer 52 M10 Split Washer 103 M8 Washer 59 M10 Washer 75 38mm Round Q Spacer 17 Spacer 106 Inner Cap 38 m L 19mm Round Inner Cap 78 25mm Square Inner Cap 54 45mm Round Inner Cap 56 50mm Round Inner Cap 57 50mm Square Inner Cap 98 57mm Round Outer Cap 27 38mm x 64mm Inner Cap 41 PART LIST Model No WEEVSY59430 R0903A Key No Qty Description Key No Qty Description 1 1 Base 59 2 M8 Washer 2 1 Base Plate 60 1 M10 x 69mm Bolt 3 1 Upright 61 6 Seat Wheel 4 1 Lat Tower 62 15 M4 x 16mm Screw 5 1 Bench Rail 63 6 M6 Zinc Nylon Locknut 6 1 Front Leg 64 2 M10 x 72mm Bolt 7 1 Leg Lever
19. o use e Do not allow children on or around machine e Replace label if damaged illegible or removed CrossBow by WEIDER is a trademark of ICON Health amp Fitness Inc 2 MONDAY Date TUESDAY Date WEDNESDAY Date THURSDAY Date FRIDAY Date AEROBIC EXERCISE EXERCISE RESISTANCE SETS REPS AEROBIC EXERCISE Make photocopies of this page for scheduling and recording your workouts 19 Rest for a short period of time after each set The ideal resting periods are e Rest for three minutes after each set for a muscle building workout e Rest for one minute after each set for a toning work out e Rest for 30 seconds after each set for a weight loss workout Plan to spend the first couple of weeks familiarising yourself with the equipment and learning the proper form for each exercise COOLING DOWN End each workout with 5 to 10 minutes of stretching Include stretches for both your arms and legs Move slowly as you stretch and do not bounce Ease into each stretch gradually and go only as far as you can without strain Stretching at the end of each workout is an effective way to increase flexibility STAYING MOTIVATED For motivation keep a record of each workout The chart on page 19 of this manual can be photocopied and used to schedule and record your workouts List the date the exercises performed the resistance used and the numbers of sets and repetit
20. olt 98 2 50mm Square Inner Cap 41 2 38mm x 64mm Inner Cap 99 2 Rail Inner Cap 42 1 Bench Knob 100 4 80 pound Crossbow Cap 43 1 Fulcrum Knob 101 2 10 pound Crossbow Cap 44 1 10 pound centre Crossbow 102 2 Large Plastic Foot 45 1 Seat Knob 103 4 M10 Split Washer 46 4 M8 x 25mm Button Head Screw 104 1 Hook 47 2 M10 Nut 105 1 Rail Bracket 48 1 Leg Press Strap 106 1 22mm Spacer 49 2 Short Handle 107 4 Snap Ring 50 1 Ankle Strap 108 1 Storage Knob Bracket 51 4 Cable Clip 109 2 Half Pulley Cover 52 4 M8 Split Washer 1 User s Manual 53 3 Plastic Foot 1 Exercise Guide 54 2 25mm Square Inner Cap 1 Exercise Decal 55 1 45mm Round Inner Bushing 1 Large Hex Key 56 2 45mm Round Inner Cap 1 Small Hex Key 57 2 50mm Round Inner Cap 5 Videocassette 58 4 M6 x 45mm Screw Note indicates a non illustrated part Specifications are subject to change without notice See the back cover of the user s manual for information about ordering replacement parts EXPLODED DRAWING Model No WEEVSY59430 R0903A 2 Ayo 193 C gt 13 61 77 63 a2 SS
21. s in use Do not add or remove crossbows from the U channels whilst the end of the long cable is pulled out Always adjust the crossbow assembly to the horizontal position and make sure the ful crum knob is secure before using the resist ance system Make sure the rings on the crossbows are pushed against the crossbow spacer before using the resistance system Make sure the storage knob is in place and fully tightened each time you use the resist ance system Make sure that the cables remain on the pul leys at all times If the cables bind as you are exercising stop immediately and make sure that the cables are on the pulleys If you feel pain or dizziness whilst exercis ing stop immediately and begin cooling down AWARNING Before beginning this or any exercise program consult your physician This is especially important for persons over the age of 35 or persons with pre existing health problems Read all instructions before using ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product BEFORE YOU BEGIN Thank you for selecting the innovative CrossBow by WEIDER LEGEND resistance system The resistance system offers a selection of stations designed to develop every major muscle group of the body Whether your goal is to tone your body build dramatic muscle size and strength or improve your cardiovascular system the resistance system will help you
22. stem in any commercial rental or institutional setting 4 Use the resistance system only on a level surface Cover the floor beneath the resist ance system to protect the floor 5 Make sure that all parts are properly tight ened each time you use the resistance sys tem Replace any worn parts immediately 6 Keep children under 12 and pets away from the resistance system at all times 7 Keep hands and feet away from moving parts 8 Always wear athletic shoes for foot protec tion whilst exercising 9 The lat tower crossbar is not designed to be used for pull up exercises Do not hang on the crossbar 10 The resistance system is designed to sup port a maximum user weight of 136 kg 300 Ibs 11 Pull on the low pulley cable only whilst sitting on the bench or standing on the base plate Pull on the high pulley cables only whilst sit ting on the bench with the seat in one of the 12 13 14 15 16 17 18 19 three positions closest to the upright base or whilst standing on the base plate The resistance system is designed to be used with the included resistance Do not use the resistance system with any other type of resistance When adding resistance both ends of the crossbows must rest under the two U channels Add and remove crossbows from the U channels one crossbow at a time Keep clear of the area around the U chan nels whilst the resistance system i
23. the Front Leg 6 Align the hole in the Leg Developer with one of the holes in the Front Leg Retighten the Knob into the Front Leg and Leg Developer CABLE DIAGRAM The cable diagram shows the proper routing of the Long Cable 80 Use the diagram to make sure that the cable has been assembled correctly If the cable has not been correctly routed the resistance system will not function properly and damage may occur The numbers show the correct route for the cable Long Cable 80 ASSEMBLY Make Things Easier for Yourself This manual is designed to ensure that the resist ance system can be assembled successfully by most people However it is important to realise that the versatile resistance system has many parts and that the assembly process will take time Most people find that by setting aside plenty of time assembly will go smoothly Before beginning assembly carefully read the following information and instructions e Assembly requires two persons e Place all parts in a cleared area and remove the packing materials Do not dispose of the packing materials until assembly is completed For help identifying small parts use the PART IDENTIFICATION CHART Note Some small parts may have been pre attached for shipping If a part is not in the parts bag check to see if it has been pre attached Before beginning assembly make sure that you have read and understand the informa tion in the box above Pr
24. to achieve the spe cific results you want For your benefit read this manual carefully before using the resistance system If you have questions ASSEMBLED DIMENSIONS Height 280 28 cm 82 in Width 167 64 cm 66 in Depth 203 2 cm 80 in Fulcrum Knob after reading this manual please call our Customer Service Department at 08457 089 009 To help us assist you please note the product model number and serial number before calling The model number is WEEVSY59430 The serial number can be found on a decal attached to the resistance system see the front cover of this manual Before reading further please review the drawing below and familiarise yourself with the parts that are labelled Crossbar Lat Tower High Pulley Crossbows Upright Storage Knob U Channel Backrest Seat Knob Leg Lever Foot Plate Low Pulley Base Plate Seat EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS Muscle Building To increase the size and strength of your muscles push them close to their maximum capacity Your mus cles will continually adapt and grow as you progres sively increase the intensity of your exercise You can adjust the intensity level of an individual exercise in two ways by changing the amount of resistance used e by changing the number of repetitions or sets per formed A repetition is one complete cycle of an exercise such as on
25. uture reference ROss BOW by WEIDER Q www iconeurope com TABLE OF CONTENTS WARNING DECAL PLACEMENT 0 0 cece eee 2 IMPORTANT PRECAUTIONS 4246 0 004 ee boew idee AE e ee deed e OL eee AL EE Pew eee 3 BEFORE Y OU BEGIN iia c4c5 en dede cd de ohne ed ees fade bea eee ae Owe SE eee ee ae 4 ASSEMBLY pg capi ett a aai eee Ged a ha alee ead wen ee d aaa bbe a aad Belia aoa 5 ADJUSTMENTS 328i ek Oa ohn eee Ed ea we hance ae Raa EA et Ae eae 13 CABLE DIAGRAM 4 44004 0322088 oe ee i Eee e dab eee ew ee hee ees 16 EXERCISE GUIDELINES gt pas ienei aaeeea ha te eke wea bola Gee peal a ee 17 ORDERING REPLACEMENT PARTS 0 000 cece ete eee Back Cover Note A PART IDENTIFICATION CHART and a PART LIST EXPLODED DRAWING are attached in the centre of this manual Remove the PART IDENTIFICATION CHART and PART LIST EXPLODED DRAWING before begin ning assembly WARNING DECAL PLACEMENT The decals shown here have been placed on the resistance Place system If a decal is missing Crossbow or if it is not legible please S N spacer this gt side of ring call our Customer Service Department to order a free replacement decal see the back cover of this manual Apply the replacement decal in the location shown Keep hands and fingers clear of this area e Misuse of this product may result in serious injury e Read user s manual and follow all warnings and operating instructions prior t
26. y slide the hook on the High Pulley Housing 21 onto an Eyebolt 34 Attach the end of the Short Cable 33 without the ball to the end of the Long Cable 80 with a Cable Clip 51 Attach the other high pulley in the same manner To use the Leg Lever not shown attach the two ends of the Leg Lever Cable 32 to the ends of the Long Cable 80 with two Cable Clips 51 Remove the high pulleys and detach the Leg Lever Cable 32 when not in use Store the ends of the Leg Lever Cable on the Hook 104 under the Bench Rail not shown ADJUSTING THE SEAT The Seat 13 can be secured in any of five positions on the Bench Rail 5 To move the Seat pull the Seat Knob 45 out as far as it will go and slide the Seat to the desired position Engage the Seat Knob into an adjustment hole in the Bench Rail To perform row exercises the leg press strap must be attached to the long cable see ATTACHING THE ACCESSORIES on page 14 and the Seat Carriage 12 must be able to roll along the Bench Rail 5 First remove the Backrest 14 from the Seat Carriage see ADJUSTING THE BACKREST on page 15 Then pull the Seat Knob 45 out as far as it will go and turn the Knob so that the pin rests at the end of the L shaped slot see the inset drawing L Slot 13 23 Locate the two Short Cables 33 Wrap one of the Cables around a 90mm Pulley 28 Attach the Pulley and a pair of Pulley Covers 29 toa High Pulley

CrossBow

Contents

Download Pdf Manuals

Related Search

Related Contents