LS-B10 - Laser Sonics
Contents
1. Indicator LED No display when in Mode4 e oOo y of Ss OO0000 Al 228248 OO No display when in Mode4 Flashes quickly e e oS OO00000 O e OO 0 Flashes slowly J e Q9 oo0oo0o0o0o0 O e OO Flashes more slowly Precision mode y Mode1 A Higher than datum position Move the sensor downward Buzzer sound High frequent beep sound Mode2 Datum position ON GRADE position Buzzer sound Continuous beep sound Modes Lower than datum position Mode4 Blinking Move the sensor upward Buzzer sound Low frequent beep sound lt gt ja gt a gt ja gt a Battery remaining display Indicates the battery remaining of laser sensor as follows EH Battery is sufficient m i The power is low but sensor is still usable Flashing alternately pa Dead battery Replace the dry battery with new one Power save function The instrument turns the power save mode after detecting no laser beam for more than approx five minutes In the power save mode the indicator LCD turns off and one indicator LED blinks green The mode is canceled automatically when the instrument detects a laser beam again The mode can also be canceled by pressing the power switch again Auto cut off function The power will be turned off automatically after detecting no laser beam for more than approx 30 minutes To turn on the laser sensor press the power switch again Sp2. is expected to follow all operating instructions and make periodic checks of the product s performance 2 The manufacturer or its representatives assumes no responsibility for results of a faulty or intentional usage or misuse including any direct indirect consequential damage and loss of profits 3 The manufacturer or its representatives assumes no responsibility for consequen tial damage and loss of profits by any disaster an earthquake storms floods etc A fire accident or an act of a third party and or a usage any other usual conditions 4 The manufacturer or its representatives assumes no responsibility for any dam age and loss of profits due to a change of data loss of data an interruption of busi ness etc caused by using the product or an unusable product 5 The manufacturer or its representatives assumes no responsibility for any dam age and loss of profits caused by usage except for explained in the user manual 6 The manufacturer or its representatives assumes no responsibility for damage caused by wrong movement or action due to connecting with other products Standard Set Composition 1 LS B10 Instrument 2 AA size dry cells 3 Instruction manual eter IPC Nomenclature and Functions Power switch Power ON Short push Power OFF Long push LCD back light ON OFF Short push when power is ON Auto turn off after two minutes Detective precision Mode switch
3. AYSIA Phone 03 42701068 Fax 03 42704508 TOPCON KOREA CORPORATION 2F Yoaseoung Bldg 1595 3 Seocho Dong Seocho gu Seoul 137 876 Korea Phone 82 2 2085 0321 Fax 82 2 2055 0319 www topcon co kr TOPCON CORPORATION BEIJING OFFICE Block No 9 Kangding Street Beijing Economic Technological Development Area Beijing China 100176 Phone 10 6780 2799 Fax 10 6780 2790 TOPCON CORPORATION DUBAI OFFICE P O Box293705 Office C 25 raw C 2 Dubai Airport Free Zone Dubai UAE Phone 971 4 2995900 Fax 971 4 2995901 TOPCON CORPORATION 75 1 Hasunuma cho Itabashi ku Tokyo 174 8580 Japan 4D Phone 3 3558 2520 Fax 3 3960 4214 www topcon co jp LS B10 31266 90022
4. Buzzer sound switch Buzzer sound Quiet Loud OFF Short push LED ON OFF Long push Indicator LCD Indicator LED Buzzer speaker Detector Magnet Battery cover Battery cover knob Please refer to the back of the instruction manual for the indicator display patterns Operation 1 Mount the LS B10 on the equipment and position a rotating laser 2 Raise or lower the machine blade or arm to position the cutting edge or bucket at the desired grade elevation 3 Turn on the LS B10 4 Keep the machine blade or arm motionless and raise or lower the LS B10 and adjust until ON GRADE position are flashing This is the ON GRADE position The reference position has been set 5 While operating use the LED display to continually check grade moving the blade or cutting filling according to the direction of the LS B10 display Indicator Height alert warning of rotating laser A flash and a buzzer sound signifies that the height alert function of rotating laser is operating This function is not usable to the rotating laser which does not have the height alert and the function to output alarm signal eee Indicator LED Flashes slowly Rotating laser battery warning A flash shows that the rotating laser power is low This function is not usable to the rotating laser which does not have the function to output alarm signal Laser beam positions and display patterns Indicator LCD
5. ecifications 120mm 4 724inches 270 Mode1 2mm 0 0066ft Mode2 6mm 0 020ft Mode3 12mm 0 039ft Mode4 30mm 0 098ft 633 780nm 700m 2300ft Using RL H1Sa wae Detective range Detective precision Detective angle Detective precision Detectable laser wave length Laser detecting range diameter 15mm 0 05ft 30mm 0 1ft width 25mm 0 08ft 50mm 0 16ft width 35mm 0 11ft 70mm 0 23 t width 60mm 0 2ft 120mm 0 39ft width When the laser beam is off to the top or to the bottom Power source Continuous operating time 20 C 68 F Operating temperature Water proof Dimensions W D H Weight Without cells Detective angle Detective precision and Laser detecting range may vary depending on rotating laser being used or atmospheric conditions AA size dry cells 3pcs Approximately 100 hours Using alkaline manganese dry cells 20 C 50 C 4 F 122 F IP66 110x36x176 mm 4 3 x1 4 x6 9 0 5kg 1 2Ibs JSIMA Japan Surveying Instruments Manufacturers Association EMC NOTICE In industrial locations or in proximity to industrial power installations this instrument might be affected by electromagnetic noise Under such conditions please test the instrument performance before use CE TOPCON POSITIONING SYSTEMS INC 7400 National Drive Livermore CA 94551 U S A Phone 925 245 8300 Fax 925 245 8599 www topcon c
6. ff TOPCON LASER SENSOR LS B10 Thank you for purchasing the TOPCON LS B10 For the best performance of the instruments please read these instructions carefully and keep them in a convenient location for future reference GENERAL HANDLING PRECAUTIONS Before starting work or operation be sure to check that the system is func tioning properly Affection of the radio waves When using the instrument in the following place the strong radio wave may cause faulty operation e Near the instrument occurring strong radio waves e g Transceiver e Near the radio wave towers such as television or radio DISPLAY FOR SAFE USE In order to encourage the safe use of products and prevent any danger to the operator and others or damage to properties important warnings are put on the products and inserted in the instruction manuals We suggest that everyone understand the meaning of the following displays and icons before reading the Safety Cautions and text INSTRUCTION MANUAL Display Meaning Ignoring or disregard of this display may lead to death or serious N WARNING injury j ere Ignoring or disregard of this display may lead to personal injury CAUTION or physical damage to the instrument Injury refers to hurt burn electric shock etc Physical damage refers to extensive damage to buildings or equipment and furni ture HANDLING PRECAUTIONS Guarding the instrument against shock When transporting the ins
7. om TOPCON CALIFORNIA 3380 Industrial Bivd Suite 105 West Sacramento CA 95691 U S A Phone 916 374 8575 Fax 918 374 8329 TOPCON EUROPE POSITIONING B V Essebaan 11 2908 LJ Capelle a d IJssel The Netherlands Phone 010 458 5077 Fax 010 284 4941 www topconeurope com IRELAND OFFICE Unit 69 Westem Parkway Business Center Lower Ballymount Road Dublin 12 Lreland Phone 01460 0021 Fax 01460 0129 TOPCON DEUTSCHLAND G m b H Giesserallee 31 47877 Willich GERMANY Phone 02154 885 100 Fax 02154 885 111 info topcon de www topcon de TOPCON S A R L 89 Rue de Paris 92585 Clichy Cedex France Phone 33 1 41069490 Fax 33 1 47390251 topcon topcon fr TOPCON SCANDINAVIA A B Neongatan 2 S 43151 M indal SWEDEN Phone 031 7109200 Fax 031 7109249 TOPCON GREAT BRITAIN LTD Topcon House Kennet Side Bone Lane Newbury Berkshire RG14 5PX U K Phone 44 1635 551120 Fax 44 1635 551170 survey sales topcon co uk laser sales topcon co uk TOPCON SOUTH ASIA PTE LTD Bik 192 Pandan Loop 07 01 Pantech Industrial Complex Singapore 128381 Phone 62780222 Fax 62733540 www topcon com sg TOPCON INSTRUMENTS THAILAND CO LTD 77 162 Sinn Sathorn Tower 37th FI Krungdhonburi Rd Klongtonsal Klongsarn Bangkok 10600 Thailand Phone 02 440 1152 7 Fax 02 440 1158 TOPCON INSTRUMENTS MALAYSIA SDN BHD Excella Business Park Block C Ground amp 1st Floor Jalan Ampang Putra Taman Ampang Hilir 55100 Kuala Lumpur MAL
8. trument provide some protection to minimize risk of shock Heavy shock may affect beam accuracy SAFETY CAUTIONS A WARNING e There is a risk of fire electric shock or physical harm if you attempt to disas semble or repair the instrument yourself This is only to be carried out by TOPCON or an authorized dealer only Risk of fire or electric shock Do not use damaged power cable plug and socket Risk of fire or electric shock Do not use a wet battery May ignite explosively Never use an instrument near flammable gas liquid matter and do not use in a coal mine Do not hold the LS B10 magnetic clamp near anyone who uses a pace maker or other electoronic medical devices The strong magnetic field can disrupt the normal operation of such devices Battery can cause explosion or injury Do not dispose in fire or heat The short circuit of a battery can cause a fire Do not short circuit battery when storing it N CAUTION Risk of injury to fingers Do not place fingers on magnet while mounting to equipment Strong magnetic field Do not place LS B10 magnetic clamp near any sensitive electronic devices or mag netic storage media such as computer disk Do not allow skin or clothing to come into contact with acid from the batteries if this does occur then wash off with copious amounts of water and seek medical advice EXCEPTIONS FROM RESPONSIBILITY 1 The user of this product
Download Pdf Manuals
Related Search