PMR BLUETOOTH HEADSET USER GUIDE
Contents
1. When prompted by the mobile phone enter the headset pin code 0000 When pairing is complete the blue LED on the headset will flash at one second intervals and the headset will be placed in standby mode ready to make and receive calls Please note if battery is low then amber light not blue light will flash If disconnection or lost link occurs it maybe due to the following reasons a Therange is over 10 feet between both headset and the mobile phone b Mobile phone disconnected the link to conserve power or enable other function c Either device has been switched off Note The headset in normal operation should maintain the connection with the mobile phone at all times once the pairing mode and connection has been established between the two devices To cancel pairing mode While you are in pairing mode you can cancel the pairing process and turn off the headset Press and hold the TALK button for three seconds Both LEDs will turn off and you will hear the OFF tone FITTING THE HEADSET ON YOUR EAR The PMR Headset is designed to fit comfortably in your ear The ear hook can be rotated on its axis allowing you to position on right or left ear Please note the ear hook is designed such that it can fit over the ear or under the ear as well as right and left ear To place the headset on your ear Place the headset speaker in your ear with the microphone angled towards your mouth The headset should fit snugly in your e2. OMR Portability Mobility WiReless ped Py Windigo PMR BLUETOOTH HEADSET P N PBTFABH2C2 P R J G USER GUIDE Declaration of Conformity We declare that product PBTFABF2C2 P conforms to the R amp TTE Directive 1999 5 RC C 0678 GETTING STARTED Remove all components from the package Items in the pack include PMR Bluetooth headset with Ear Hook Ear Cap User Guide Lanyard optional amp Mains Adapter Please check the contents carefully and contact your local dealer immediately if there are any shortages GETTING TO KNOW YOUR HEADSET Please note some models of headset will differ slightly in style and the functionality may vary on certain models according to their specifications Talk Button Amber LED Volume Up Blue LED Volume Down CHARGING YOUR HEADSET Before using the headset you must charge the headset for approximately two hours When fully charged the battery provides up to 5 hours of talk time and up to 100 hours of standby time Please note talk time is also a function of the mobile phone and factory determined settings of the phone so you may find this figure is reduced under certain conditions To charge the headset 1 Plug the AC adapter into the headset 2 Plug the AC adapter into a wall outlet When the headset is charging the amber LED will light up 3 Unplug the charger cable from the wall outlet and the headset when charging has finished the amber LED will tur
3. ar However if the speaker is too small for your ear you can change to other size of the ear cap that is provided with your headset To add the ear cap Stretch the ear cap around the end of the speaker To add the Optional Lanyard simply connect via the small hole at the base of the ear hook WARNING It is possible to remove the ear hook and replace but for normal operation and fitment this is NOT necessary Simply rotating the ear hook on its axis will allow easy fitment to the ear POWERING YOUR HEADSET To turn on the headset Press and hold the Talk button for four seconds You will hear the ON tone The headset turns on and is placed in standby mode ready to make and receive Calls To turn off the headset When the headset is on press and hold the Talk button for four seconds You will hear the OFF tone The headset turns off MAKING CALLS You can make calls from your mobile phone or directly from the headset using voice dialing commands if this feature is supported by your mobile phone To make calls from your mobile phone Dial the call from your mobile phone Dependent on your mobile phone settings the call is automatically connected to your headset To make calls using voice dialing if supported by your mobile phone Press the Talk button on your headset Speak the name of the person you wish to call The call is automatically connected to your headset RECEIVING CALLS You must configure your mobil
4. ate third party software in order to enable correct operation When Talk button is Unit not charged pressed no LED Consult authorized dealer indicator Headset powers on Check unit is paired to with blue LED flashing phone Check settings in but no connection to phone Headset default mobile phone name is BTHS Check phone is switched on Check handsfree settings for phone Ensure headset amp phone are within range Check mains charger Headset does not adapter is connected to charge the headset securely amp is switched on Check mains charger is working using another device Consult authorized dealer CUSTOMER SERVICE INFORMATION For other PMR Bluetooth products or support please view our website www pmrtechnology co uk or email support pmrtechnology co uk or contact your local representative DISCLAIMER Whilst every effort has been made to ensure that the information in this manual is accurate and complete no liability will be accepted for any errors and or omissions made The manufacturer reserves the right to make changes and improvements to the specifications and features of the hardware and firmware of the products described in this document without prior notice Reproduction transfer distribution or storage of part or all of the contents in this document in any form is prohibited without prior permission of the manufacturer All trademarks acknowledged
5. e phone to answer calls directly on your Bluetooth headset Refer to the mobile phone user guide for instructions for initiating this feature When your mobile phone rings press the Talk button on your headset The call is automatically connected to your headset Please note you can also Reject calls by depressing the talk button for about 3 seconds Not all phones support this feature ENDING CALLS When you have finished your call press the Talk button on your headset The call will be disconnected TRANSFERRING CALLS You can transfer calls connected to your headset back to your mobile phone or from your mobile phone to your headset Not all phones support this feature To transfer calls from your headset to the phone or from the phone to the Headset press the talk button for about 3 seconds until you hear the tone ADJUSTING THE VOLUME To increase the volume Press click the top of the Volume button to increase volume by 1 step repeat this procedure until you have reached the desired level To decrease the volume Press click the bottom of the Volume button to decrease the volume by one step repeat this procedure until you have reached the desired level MUTING THE HEADSET You can mute and un mute the microphone temporarily so that you cannot be heard by the connected party To mute the headset Press and hold the Volume up button for three seconds To un mute the headset When the microphone is mu
6. n off or be dim Battery Indication The amber LED can turn off after 2 3 hours charging This will indicate that the Headset can be used however it is recommended that the user charges for a full 2 hours in order to fully charge the battery for normal operation PAIRING THE HEADSET TO YOUR MOBILE PHONE Pairing is the process of linking the headset with your Bluetooth mobile phone Before you use the PMR headset with your mobile phone you must pair the devices After this process is completed you can use the headset only with its paired mobile phone If you wish to use the headset with a different mobile phone you must repeat the pairing process with the new mobile phone In this case the headset will no longer work with the original mobile phone Please refer to the user manual of your mobile phone for further information on How to Pair Before you pair the headset ensure that the battery is fully charged and that your mobile is switched on and it is in discoverable mode To pair the devices l With the headset turned off press and hold the TALK button for five seconds The blue and amber LEDs will flash alternately and you will hear the PAIRING tone Release the TALK button The headset is now in Pairing Mode Turn on the mobile phone and place it within 10 feet of the headset Initiate the device discovery feature on the mobile phone Refer to the mobile phone user guide for instructions for initiating this feature
7. ted press and hold either Volume button for three seconds VOICE DIAL Press the talk button when Headset is not on a call a voice prompt will be heard This is also a phone dependent feature LAST NUMBER REDIAL Certain models only may have this feature Depress either volume button when headset is not on call for about 3 second interval and this will enable the phone to provide last number redial or alternatively press both volume up and down together VISUAL INDICATORS Visual Indicators Two LEDs blue and amber indicate the status of the headset Battery 2 3 full Amber LED is off or dim Amber LED on instead of Blue LED Headset off Both LEDs are off Headset in standby Blue LED flashes at 4 mode ready to make amp second intervals receive calls Battery low Y Blue and amber LEDs flash Headset in pairing mode alternately Headset making connection audio connection for voice dial Blue LED twice quickly at 1 second intervals Blue LED flashes four times quickly at one second intervals Headset in talk mode TROUBLESHOOTING Please note that you should also be familiar with the operation of your mobile phone and how to connect to Bluetooth devices Please read your mobile phone user guide carefully Please note that the Bluetooth headset will only work with Bluetooth mobile phones For operation with a PC or laptop device please note that these devices should also be Bluetooth enabled with appropri
Download Pdf Manuals
Related Search