English - Vivotek
Contents
1. IPs e g 169 254 xx xx and the LiveClient software will not be able to detect their presence EN 6 6 J Initial Configuration 1 Once your NVR is started you will be prompted by the Setup Wizard You should then begin the initial setup The system is booted from an embedded IDE flash No software installation is required Teret 2 Enter the default User name and Password as admin amp admin It is recommended you change the password later to prevent unauthorized access 3 Click Next to proceed with configuration and follow the onscreen instructions to finish the configuration process 4 Note the following when you move to the Network page 4 1 lf your local network has a DHCP server you can select the Get IP address automatically DHCP 4 2 If your LAN port connects to an isolated switch with cameras attached to it you can manually assign IP addresses to cameras and the address for the LAN port itself ill verom ma The default static IP for the LAN port is 192 168 1 10 KAPE 4 3 Connect your WAN port to a router or AP with the routing capability and then to a DSL or Cable modem 5 On the Disk page Select disk drives by clicking the checkboxes in front of disk drives Select Build single disk Build RAIDO RAID1 or other option from the Disk configuration pull down menu Click Apply and wait for a few minutes for the configuration to take effect Refer to the descriptio2. X VIVOTEK ND8307 Network Video Recorder Quick Installation Guide English 4 P A4 Francais Espa ol Deutsch Portugu s Italiano T rk e Polski Pyccku Cesky Svenska Nederlands Dansk Indonesia y yall k Warning Before Installation Power off the Network Video Keep the Network Video Recorder Recorder if you detect abnormal away from water If the Video Recorder smell or smoke coming from it is wet power off immediately Do not place the Network Video Refer to your user s manual for the Recorder around the heat sources operating temperature such as television or oven O Keep the Network Video Recorder O Do not place the Network Video away from direct sunlight Recorder in high humidity environments O Do not attempt to remove or uninstall the software on the mounted IDE flash Nor should you open the chassis Doing so will void our warranty J Package Contents ND8301 Power Cord amp Adaptor Software CD Quick Installation Guide EN 1 English 2 J Physical Description Front View Disk 1 HDD LED Power button amp LED Reset button Disk 2 Rear View RS 232 reserved LAN WAN Line In USB2 Line Out DC Power Fan exhaust VGA combo eSATA outlet comba MIC In N IMPORTANT It is imp
3. el Lock EN 4 Interface Connections 1 amp 2 Connect CAT5 or better quality Ethernet cables to cameras via a local switched network or clients through the Internet Refer to next page for more information 3 Connect the DB15 VGA port to a monitor with resolutions up to 1920x1080 4 Connect USB devices such as keyboard and mouse 5 If an external eSATA storage enclosure is available connect it to the eSATA port 6 Connect speakers or microphone to the phone jack connectors 7 Connect the supplied 100 240V DC power adaptor 50 60Hz 5A LAN WAN External enclosure EN 5 English 4 J Network Deployment 1 Connect the supplied power adapter to a power outlet 2 Connect network cameras to the NVR s LAN ports 3 If you want to access NVR over the Internet connect the NVR to the Internet via the WAN port A web console can be established from a remote PC by keying http lt public IP gt 3454 in a browser s URL address field However port forwarding on the router for the TCP port will be necessary 4 Push the power button to run the NVR a Clients BL Internet Default Fixed IP 192 168 1 10 Q NOTE The LAN and WAN ports can be configured into the same or different subnets If you have cameras connected via the WAN port make sure the WAN port acquires an IP address from a DHCP server on router or AP If not the cameras detected through the WAN port will use the default
4. m s limits In terms of local display the default stream 1 for live view can be configured with a resolution up to Full HD 30fps Stream 1 is also a source for continuous recording Make sure your cameras stream 1 resolution does not exceed 1080P at 30fps H 264 Mooses o T T 7 The NVR supports Auto Stream Size which automatically adjusts streaming display for efficient leverage of system resources If you disable the Auto Stream Size function and manually configure your stream settings you must comply with the limitations listed above 5 After inserting your cameras you can start dragging cameras into view cells and proceeding with the rest of the configuration Refer to your User Manual for more information EN 9 window and click the Insert button ai Heart Sem ial English VIVOTEK INC 6F No 192 Lien Cheng Rd Chung Ho New Taipei City 235 Taiwan R O C T 886 2 82455282 F 886 2 82455532 E sales vivotek com VIVOTEK Netherlands B V Busplein 36 1315KV Almere The Netherlands T 31 0 36 5389 149 F 31 0 36 5389 111 E saleseurope vivotek com VIVOTEK USA INC 2050 Ringwood Avenue San Jose CA 95131 T 408 773 8686 F 408 773 8298 E salesusa vivotek com
5. n available with every disk volume type on the screen such as those for RAIDO and RAID1 EN 7 English 6 On the Camera page all cameras connected through the local network should appear on a Camera list after a brief search You can manually assign IP addresses by clicking on the cameras address field You can also select the Assign IP addresses to all cameras checkbox and let NVR assign IPs to cameras Click Next to end the initial setup Make sure you have the cameras access credentials in order to make individual changes 6 Ready to Use 1 You will then be at the Control Center screen Double click on the LiveClient or Playback buttons to configure live viewing and recording settings 2 Open the LiveClient utility to change live view layout camera streaming frame rate and other options EN 8 3 3 1 By default the Batch Insert Cameras window will prompt for you to recruit cameras into your configuration If it does not you can enter the Configuration menu select Camera Management gt Batch Insert Cameras a hasa wr 3 3 Select cameras by clicking their i mu O ata checkboxes 1 ze bn m Meer set ee ao a TaN ARGE 3 4 Click OK return to the previous 4 Pu Q sm eee Be ee W SB fede r HE ma srg Ae eee ee PH EZE IT EE 742 ee n 4 Itis important to ensure that the live vie wing and recording configuration does not exceed the syste
6. ortant to leave a clearance of 15cm to the rear side of the chassis The clearance is required to ensure an adequate airflow through the chassis to ventilate heat A 5cm clearance is also required on both sides of the chassis 15cm Oo s To ensure normal operation maintain a a 3 a ambient airflow Do not block the airflow around chassis such as placing the sys tem in a closed cabinet m EN 2 SATA hard disk s are user supplied The network video recorder can readily accommodate most of the off the shelf SATA hard drives 1 Use a flat blade screwdriver to unlock the rotary bezel lock Open the drive bay bezel by pulling the lever on it Bezel Lock Bezel Lever 2 Install your hard disk to the drive bay Gently put the hard disk into drive bay with its label side facing up and the connector side towards the inside of the chassis Push the hard disk in Stop pushing it when you feel the contact resistance EN 3 English 3 Close the drive bay bezel 4 4 1 Press on the left edge of the drive bay bezel to snap it into place 4 2 Use a flat blade screwdriver to turn the bezel lock to the locked position You should always lock the drive bezel when the drive bay is populated This en sures the hard drive is securely installed Bez
Download Pdf Manuals
Related Search