User Manual
Contents
1. 6 1 Configuring Unicorn3101 using Web Browser Unicorn 3101 has embedded Web server and HTML pages that allow users to configure the Unicorn 3101 through an easy to use Web browser interface such as Microsoft s Internet Explorer or Netscape browser Below is a screen shot of the Unicorn 3101 configuration page Om Oves Hanlong SIP Server 000000 william xanadu hanlongtec cn g sip mycompany com or IP address VOIP Device 1 92 168 0 100 e g proxy myprovider com or IP address if any ONo No butsend keep alive OSTUN OUPNP Configuration 8200 the user part of an SIP address 8200 can be identical to or different from SIP User ID DEVICE STATUS 0 purposely not displayed for securitiprotection SUPER OPTIONS FXS PORT L Use DNS SRV No OYes User ID is phone number No OYes SIP Registration ONo yYes Unregister On Reboot No Yes N Register Expiration Expiration TI M o RR in minutes default 1 hour max 45 2 in minutes default 1 hour max45 days 00000 ores hea MN Call without local local SIP pot local SIP pot 5o60 060 q efauts0s0 00000 5060 6 1 1 Accessing the Web Configuration The Unicorn 3101 configuration page can be accessed via the LAN or WAN port The GUI interface can be download at bellow http www hanlongtek com books 83101 qgui rar This gui include bellow pages SCREENSHOT OF DEVICE STATUS PAGE SCREENSHOT OF BASIC OPTIONS PAGE SCREENS2. When set to Yes a SUBSCRIBE for Message Waiting Indication will be sent periodically If this parameter is set to Yes the From header in Unicorn 3101 User Manual Page 23 of 28 Firmware 1 0 0 46 Last Updated Anonymous Call Rejection Check SIP User ID for incoming INVITE Session Expiration Min SE Caller Request Timer Callee Request Timer Force Timer UAC Specify Refresher UAS Specify Refresher Force INVITE Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY outgoing INVITE message will be set to anonymous essentially blocking the Caller ID from displaying Default is NO if set to YES the anonymous call will be rejected with busy message Check the SIP User ID in Request URI If they don t match the call will be rejected The session timer extension enables SIP sessions to be periodically refreshed via a re INVITE request Once the session interval expires if there is no refresh via a re INVITE message the session will be terminated Session Expiration is the time in seconds at which the session is considered timed out if no successful session refresh transaction occurs beforehand The default value is 180 seconds Default is 180 seconds The minimum session expiration in seconds Default is 90 seconds If selecting Yes the device will use session timer when it makes outbound calls if remote party supports session timer Default is NO If selecting Yes the phone will use session t
3. in this document is subject to change without notice No part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of Hanlong Technology 5 BASIC OPERATIONS 5 1 Get Familiar with Voice Unicorn 3101 has stored a voice prompt menu for quick access to settings and simple configuration You can enter this voice prompt menu one ways e Pick up the receiver or press the Handsfree button of the analog telephone and press A voice will say Enter the new option At this point you can select from the following menu voice prompt options to begin using the Unicorn 3101 Menu Voice Will Say the Following Main Enter a Menu Option Enter for the next menu option Menu Enter to return to the main menu Enter 01 07 12 17 47 86 or 99 Menu R E BHR opion 01 DHCP Mode Static IP Mode Enter 9 to toggle the selection If user selects Static IP Mode user need configure all the IP address information through menu 02 to 05 If user selects Dynamic IP Mode the device will retrieve all IP address information from DHCP server Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 6 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012 IP Address IP address TECHNOLOGY The current WAN IP address i
4. period when the cradle is pressed Hook Flash to simulate FLASH To prevent unwanted activation of the Flash Hold and automatic phone ring back adjust this time value Voice path volume adjustment Rx is a gain level for signals transmitted by FXS Tx is a gain level for signals received by FXS Default OdB for both parameters Loudest volume 6dB Lowest volume 6dB User can adjust volume of call on either end using the Rx Gain Level parameter and the Tx Gain Level parameter located on the FXS Port Configuration page If call volume is too low when using the FXS port ie the ATA is at user site adjust volume using the Rx Gain Level parameter under the FXS Port Configuration page If voice volume is too low at the other end user may increase the far end volume using the Tx Gain Level parameter under the FXS Port Configuration page This function lets you configure ring tone cadence preferences User has 10 choices The configuration completed in Distinctive Ring Tones block in the same page applies to ring tones cadences configured here 6 1 7 Saving the Configuration Changes Once a change is made users should click on the SaveSet button in the Configuration page as follow Hanlong Technology Co Ltd 1 19 2012 Unicorn 3101 User Manual Page 25 of 28 Firmware 1 0 0 46 Last Updated TECHNOLOG Ring Tone 8 c 2000 4000 Ring Tone 10 c 2000 4000 TESI Revoot J AB Rishis Reserved H
5. up To configure the TFTP server via the Web configuration interface open up your browser to point at the IP address of the Unicorn 3101 Input the admin password to enter the configuration screen From there enter the TFTP server address in the designated field towards the bottom of the configuration screen Once the TFTP server is configured please power cycle the Unicorn 3101 TFTP process may take as long as 1 to 2 minutes over the Internet or just 20 seconds if itis performed on a LAN Users are recommended to conduct TFTP upgrade in a controlled LAN environment if possible For those who do not have a local TFTP server Hanlong provides a NAT friendly TFTP server on the public Internet for firmware upgrade Please check the Service section of Hanlong s Web site to obtain this TFTP server s IP address NOTES When Hanlong ATA boot up it will send TFTP or HTTP request to download configuration files there are two configuration files one is cfg txt and the other is cfg001fc1xxxxxx where 001fc1xxxxxx is the MAC address of the Unicorn 3101 These two files are for initial automatically provisioning purpose only for normal TFTP or HTTP firmware upgrade the following error messages in a TFTP or HTTP server log can be ignored 8 RESTORE FACTORY DEFAULT SETTINGS Warning Restoring to the factory default settings will delete all configuration information of the device oteps to follow in restoring to factory default setti
6. will attempt to detect if and what type of firewall NAT it is sitting behind through communication with the specified STUN server If the detected NAT is a Full Cone Restricted Cone or a Port Restricted Cone the Unicorn 3101 will attempt to use its mapped public IP address and port in all its SIP and SDP messages If choosing STUN with no specified STUN server the Unicorn 3101 will periodically every 20 seconds or so send a blank UDP packet with no payload data to the SIP server to keep the hole on the NAT open If choosing UPNP the embedded UPNP client inside the Unicorn 3101 will attempt to mapping ports with the router by upnp protocol SIP service subscriber s User ID SIP service subscriber s Authenticate ID Can be identical to or different from SIP User ID SIP service subscriber s account password SIP service subscriber s name which will be used for Caller ID display Default is No If set to Yes the client will use DNS SRV for server lookup If the Unicorn 3101 has an assigned PSTN telephone number this field should be set to Yes Otherwise set it to No If Yes is set a user phone parameter will be attached to the From header in SIP request This parameter controls whether the Unicorn 3101 Unicorn 3101 User Manual Page 19 of 28 Firmware 1 0 0 46 Last Updated Unregister On Reboot Register Expiration Outgoing Call without Registration Local SIP port Local RTP port Use random port Re
7. x10ms frames for G726 it is 20 x10ms frames for G723 it is 32 x30ms frames for G729 G728 64 Unicorn 3101 User Manual Page 21 of 28 Firmware 1 0 0 46 Last Updated G723 Rate SRTP Mode Optional VAD Symmetric RTP Fax Mode Fax Tone Detection Mode Jitter Buffer Type Jitter Buffer Length Distinctive Ring Tone Use Bell style 3 way Conference Disable Call Waiting Disable Call Waiting Tone Ring Timeout No Key Entry Timeout Use ff as Dial Key Dial Plan Hanlong Technology Co Ltd 1 19 2012 x10ms and 64 x2 5ms frames respectively This defines the encoding rate for G723 vocoder By default 6 3kbps rate is chosen Enable SRTP mode based on selection Default is No Default is No VAD allows detecting the absence of audio and conserve bandwidth by preventing the transmission of silent packets over the network Default is No When set to Yes the device will change the destination to send RTP packets to the source IP address and port of the inbound RTP packet last received by the device Default is T 30 Fax Pass Through or T 38 Auto Detect FolP Default is Callee This decides whether Caller or Callee sends out the re INVITE for T 38 or Fax Pass Through Select either Fixed or Adaptive based on network conditions Select Low Medium or High based on network conditions Caller ID must be configured Select a Distinctive Ring Tone 1 through 3 for a particular Caller ID
8. 1 when dialing Example 1 369 11 1617xxxxxxx Allow 311 611 911 and any 10 digit numbers of leading digits 1617 Example 2 1900x 216172xxxxxxx Block any number of leading digits 1900 and add prefix 1617 for any dialed 7 digit numbers Example 3 1xxx 2 9 xxxxxx lt 2 011 gt x Allow any length of number with leading digit 2 and 10 digit numbers of leading digit 1 and leading exchange number between 2 and 9 if leading digit is 2 replace leading digit 2 with 011 before dialing 3 Default Outgoing x Example of a simple dial plan used in a Home Office in the US 1900x lt 1617 gt 2 9 xxxxxx 1 2 9 xx 2 9 xxxxxx 011 2 9 x 8469 11 Explanation of example rule reading from left to right 1900x prevents dialing any number started with 1900 lt 1617 gt 2 9 xxxxxx allows dialing to local area code 617 numbers by dialing 7 numbers and 1617 area code will be added automatically 1 2 9 xx 2 9 xxxxxx allows dialing to any US Canada Number with 11 digits length 011 2 9 x allows international calls starting with 011 3469 11 allow dialing special and emergency numbers 311 411 611 and 911 Note In some cases user wishes to dial strings such as 123 to activate voice mail or other application provided by service provider In this case should be predefined inside dial plan feature and the Dial Plan should be x More information can be availabled at Dail Plan Notes Default is No
9. 1xxxxxx is the MAC address of the Unicorn 3101 For more information regarding configuration file format please refer to the related technical documentation The configuration file can be downloaded via TFTP or HTTP from the central server A service provider or an enterprise with large deployment of Unicorn 3101s can easily Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 26 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY manage the configuration and service provisioning of individual devices remotely and automatically from a central server The central provisioning system uses enhanced NAT friendly TFTP or HTTP thus no NAT issues and other communication protocols to communicate with each individual Unicorn 3101 for firmware upgrade etc 7 SOFTWARE UPGRADE To upgrade software Unicorn 3101 can be configured with a TFTP server where the new code image is located The TFTP upgrade can work in either static IP or DHCP mode using private or public IP address It is recommended to set the TFTP server address in either a public IP address or on the same LAN with the Unicorn 3101 There are two ways to set up the TF TP server to upgrade the firmware namely through voice menu prompt or via the Unicorn 3101 s Web configuration interface To configure the TFTP server via voice prompt follow section 5 1 with option 06 once set up the TFTP IP address power cycle the ATA the firmware will be fetched once the ATA boots
10. End User Password Reply to ICMP on WAN Port WAN Side Http Access PSTN Access Code Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY Static IP mode are not used even though they are still saved in the chipset s memory The Unicorn 3101 will acquire its IP address from the first DHCP server it discovers from the office home network it is connected to To use the PPPoE feature the PPPoE account settings need to be set The Unicorn 3101 will attempt to establish a PPPoE session if any of the PPPoE fields have been entered with data f Static IP mode is enabled then the IP address Subnet Mask Default Router IP address DNS Server 1 primary DNS Server 2 secondary fields will need to be configured by the user These fields are reset to zero by default This parameter controls how the displayed date time will be adjusted according to the specified time zone If set yes and under DHCP mode the device will try to get option 2 from DHCP configure and overwrite Time Zone This parameter controls whether the displayed time will be daylight savings time or not If set to Yes then the displayed time will be 1 hour ahead of normal time This parameter controls whether the device is working in NAT router mode or Bridge mode Need save the setting and reboot the device before the setting start to work Sets the LAN subnet mask Default value is 255 255 255 0 Base IP for the LAN port which functions as a Gateway for the subne
11. HOT OF SUPPER OPTIONS PAGE SCREENSHOT OF FXS PORT PAGE map 6 1 2 Programming Unicorn 3101 via the LAN Port To program Unicorn 3101 via the LAN port directly connect an Ethernet cable from your PC to the LAN port of the Unicorn 3101 After connecting the cable confirm that the green light of the LAN port is on If the green light is not on this means that your PC is not yet properly connected to the Unicorn 3101 via the LAN port For LAN port configuration use the following default IP address to access the device Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 13 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012 HAN LON G TECHNOLOGY http 192 168 22 1 6 1 3 Programming Unicorn 3101 via the WAN Port jwawPoio rave 5 LAN Pot PmbedUDP v BEEN End User Password Basic user password to configure this device Reply to ICMP on WAN port O No Yes Unit will not respond to PING from WAN side if set to No WAN side http access O No Yes WAN side access to http server will be rejected if set to No PSTN access code 00 5 key pattern to use PSTN ine default is 00 SaveSet_ All Rights Reserved Hanlong Technology CO LTD 2005 2008 The WAN port access for web configuration is disabled by default from the factory To access the web configuration menu from the WAN port you must first access the device via the device LAN port see instructions above Programmi
12. TP Server Allow DHCP Option 42 to override NTP server Lock Keypad Update Disable Voice Prompt Syslog Server Syslog Level Download Device Configuration Call Progress Tones Import TLS Certificate File Optional Restore Configuration 6 1 6 4 FXS Port Hanlong Technology Co Ltd 1 19 2012 Set the ip address of snmp trap Set another ip address of snmp trap Set another ip address of snmp trap Set another ip address of snmp trap This parameter defines the URI or IP address of the NTP server which is used by the Unicorn 3101 to set the current date time If set Yes device can get NTP server from DHCP option 42 If this parameter is set to Yes the configuration update via keypad is disabled Default is NO The IP address or URL of System log server This feature is especially useful for the ITSP Internet Telephone Service Provider Default is blank the feature is useful for the Internet Telephone Service Provider User can download configuration from the web page and save to configuration file Using these settings users can configure tone frequencies and cadence according to their preference By default they are set to North American frequencies Configure these settings with known values to avoid uncomfortable high pitch sounds ON is the period of ringing On time in ms while OFF is the period of silence In order to set a continuous tone OFF should be zero Otherwise it will ring ON ms
13. The device will ONLY use selected ring tones for particular Caller IDs For all other calls the device will use System Ring Tone When selected and no Caller ID is configured the selected ring tone will be used for all incoming calls Conference mode default option is No If set to yes the feature code for coference 23 would be disabled Default is NO User can use star codes to enable disable call waiting Default is NO This is to disable the stutter call waiting tone when a call waiting call arrived An incoming call will stop ringing when not picked up given a specific period of time Default is 4 seconds This parameter allows users to configure the key to be used as the Send or Dial key If set to Yes pressing this key will immediately trigger the sending of dialed string collected so far In this case this key is essentially equivalent to the Re Dial key If set to No this key will then be included as part of the dial string to be sent out Dial Plan Rules Unicorn 3101 User Manual Firmware 1 0 0 46 Page 22 of 28 Last Updated SUBSCRIBE for MWI Send Anonymous Hanlong Technology Co Ltd 1 19 2012 1 Accept Digits 1 2 3 4 5 6 7 8 9 0 A a B b C c D d 2 Grammar x any digit from 0 9 a XX at least 2 digits number b xx at least 2 digits number c exclude d 3 5 any digit of 3 4 or 5 e 147 any digit 1 4 or 7 f 22011 replace digit 2 with 01
14. User Manual Unicorn 3101 Analog Telephone Adaptor tum i aie Berg r1 A p y t k Hanlong Technology Co Ltd http www hanlongtek com TECHNOLOGY 1 WELCOME LEE eee eee eee eee MH 3 2 WHAT IS IN THE PACKAGE picgcccceceecssecccccesceecesseteseececcceesssececessasseteccsteexsesseecsansseeeenen 3 9 PRODUCT OVERVIEW eee ne oe ene eee enone eer casa etis e ee eee 3 3 1 Key CMC cc 3 3 2 Hardware specification cccccccccseccceseeceeeeceeeeceueeeeeeseeeessueeseueesseeessneesseees 4 SEE INSTAELATIONS 5 4 1 scu 6 5 BASIC OPERATIONS 2 cxi kasnuo sanant tede mt ix RUE oon ad duc usa su sia eec usto ausa Ce eler 6 5 1 Get Familiar with Voice cccccccccccceececcescceeeeeceeeuececeueeeseeeeessseetsgeesseeeeees 6 5 2 MOKO TON CUI PRO OO 8 5 2 1 Calling Phone or Extension NUMDE NS cccccseeeeeeeeeeeeeeeeeeeeeeaeeeees 8 oaz AN ONG esee i E EE SEE 8 523 GUWANG eosa E E E E EREA E EE 8 524 3 eese METTE M 8 Star Code Style 3 way Conference cccccceeecceceeeeeeeceeeeeeeseeeeeeeseaeeeeseeaeeeesaaees 8 Bellcore Style 3 way Conference ccccceeccccseeceeeseeeceeeeeeseesseeeeeesseeeeeseaeeeeeeeas 9 525 Direci NIP STOP CANS 252 sorten niasin ERE ADR ERE insat NEDE duties 9 520 corii ae er oe ne TESTS 10 o2 JdQiended lFAariSIelu creiere EEEE EE EEE 10 5 2 8 Make and R
15. and a pause of OFF ms and then repeat the pattern Example configuration for N A Dialtone f1 350 13 f2 440 13 c 0 0 Syntax f1 freq vol f2 freq vol c 0n1 off1 on2 off2 on3 off3 Note freq 0 4000Hz vol 30 OdBm User can import the TLS Certification User can restore the before configuration from the configuration file saved at local pc FXS PORT Unicorn 3101 User Manual Firmware 1 0 0 46 Page 18 of 28 Last Updated Setting options Account Active SIP Server Outbound Proxy SIP transport Optional NAT Traversal SIP User ID Authenticate ID Authenticate Password Name Use DNS SRV User ID is phone number SIP Registration Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY Definitions Set to the YES the account can be available SIP Server s URI or IP address SIP Outbound Proxy Server s URI or IP address Select transport between UDP and TLS default is UDP This parameter defines whether the Unicorn 3101 NAT traversal mechanism will be activated or not lf Choosing No nothing to do lf Choosing No but send keep alive the Unicorn 3101 will periodically every 20 seconds or so send a blank UDP packet with no payload data to the SIP server to keep the hole on the NAT open If choosing STUN and a STUN server is also specified then the Unicorn 3101 will behave according to the STUN client specification Under this mode the embedded STUN client inside the Unicorn 3101
16. anlong Technology CO LTD 2005 2008 The Unicorn 3101 will then display the following screen to confirm that the changes have been saved Please allow 5 to 10 seconds before rebooting the device Ring Tone 9 c 2000 4000 Ring Tone 10 jc 2000 4000 All Rights Reserved Handong Technology CO LTD 2005 2008 6 1 8 Rebooting the Unicorn 3101 You can reboot the Unicorn 3101 by clicking on the Reboot button after each update to the configuration page Alternatively you can reboot by unplugging the power supply of the Unicorn 3101 and then powering it on again If your Unicorn 3101 ever becomes stuck or un responsive you can unplug the power supply to reboot it Frequent rebooting by unplugging the power supply is not recommended and should not be necessary 6 2 Configuring Unicorn 3101 via Voice Prompt 6 2 1 DHCP Mode Follow section 5 1 with voice menu option 01 to enable Unicorn 3101 to use DHCP 6 2 2 Static IP Mode Follow section 5 1 with voice menu option 01 to enable Unicorn 3101 to use STATIC IP mode then use option 02 03 04 to set up Unicorn 3101 s IP Subnet Mask Gateway respectively 6 3 Configuration through a Central Server Unicorn 3101 devices can be automatically configured from a central provisioning system When Unicorn 3101 boots up it will send TFTP or HTTP request to download configuration files There are two configuration files one is cfg txt and the other is cfg001fc1xxxxxx where 001fc
17. eceive PSTN Calls eese 11 5 3 A SAI CS EA E E sepascpsenench ET 11 5 3 1 Call Features Tables eee eee mm 11 532 POTN PaSST FOUGR et 12 5 4 gl 12 5 5 Status Light Indicator eeeeeesseeeessesesesseeeeennreeenn nnns 12 6 CONFIGURATION GUIDE 1 e eeeeeeeeennn EE REESE ERE ELLLER sana nsa nasus anna 13 6 1 Configuring Unicorn3101 using Web Browser ccccsseeeeeeeeeeeeeeeeeeees 13 6 1 1 Accessing the Web Configuration ccccccccccceeeeeeeceeeeeeesseeeeesaeees 13 6 1 2 Programming Unicorn 3101 via the LAN Port ssssse 13 6 1 3 Programming Unicorn 3101 via the WAN Port sssssssse 14 6 1 4 User Programming and Configuration seeeeeseeeessses 14 6 10 PassWOloSunenescnuniseniisantedprbtbodmbenideprie Fenaaiauetesh ue quidne EEIE T 14 6 1 6 Configuration Options and Explanations esee 15 oao DEVTE I SEE SE iM DU MEM UIN DEMENS 15 6 1 6 2 Basic Options Settings seseeeeeeseeeeeeeeeeennn 15 6 1 6 3 Super Options Setting seeeeeeessseeseeeeeennnene 17 DIL Du FAS DO u estime ee en ee eee eee 18 6 1 7 Saving the Configuration Changes cccccccsseeceseeseeeeseeeeeeeeaeeeeeeas 25 6 1 8 Rebooting the Unicorn 3101 2 0 eeccceeeeee
18. er which can be the value used for IP Precedence or Diff Serv or MPLS Default value is 48 This contains the value used for layer 2 VLAN tag Default setting is 0 When using Bridge Mode Data VLAN Tag is supported when your PC connect to LAN Port data from your PC to switch will be tagged with Data VLAN Tag IP address or domain name of stun server This parameter specifies how often the Unicorn 3101 sends a blank UDP packet to the SIP server in order to keep the hole on the NAT open Upgrade or provisioning through TFTP or TFTP server Upgrade Via select HTTP or TFTP mode Allow DHCP Option support 66 128 150 If select yes device will get server information from DHCP option and ignore the Config Server Path Option 66 TFTP server name if you select Upgrade Via gt TFTP HTTP server name if you select Upgrade Via gt HTTP Option 128 TFPT Server IP address if you select Upgrade Via TFTP HTTP Server IP address if you select Upgrade Via gt HTTP Option 150 TFTP server address if you selectUpgrade Via gt T FTP HTTP server address if you select Upgrade Via HTTP configure file would be authenticated before acceptance if set to Yes If set Yes The SNMP function will be work Set the community of read operation Set the community of write operation Unicorn 3101 User Manual Firmware 1 0 0 46 Page 17 of 28 Last Updated SNMP Manager IP 1 SNMP Manager IP 2 SNMP Manager IP 3 SNMP Manager IP 4 N
19. eseeeeesaeeeesaeeeesaeeeessaeeeees 26 6 2 Configuring Unicorn 3101 via Voice Prompt eseeeeeeeeeeeee 26 6 2 1 DAOP NES e E E E 26 Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 2 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012 lee TECHNOLOGY SPP ame AP MOE sa a A E O 26 6 3 Configuration through a Central Server ccccceeecccceeeeeeeeeeeeeeeseeeeeeeesaeees 26 SOFTWARE UPGRADE 44555 nr naidaan niaaa advecdoussbecesseuctscevnesctde 27 RESTORE FACTORY DEFAULT SETTINGG c c sscseeeeccsssseeeeseeenseeeeseeeenseeees 27 TECHNICAL SUPPORT CONTACT sssseeeeccsssseeeeseeesseeeesscnasseesseeeanseeeeseonaaes 28 WELCOME Unicorn 3101 is an all in one VoIP integrated access device that features superb audio quality rich functionalities high level of integration compactness and ultra affordability The Unicorn 3101 is fully compatible with SIP industry standard and can interoperate with many other SIP compliant devices and software on the market Special compatibility features include Nortel MCS Standard SIP Broadsoft Howdy WHAT IS IN THE PACKAGE The Unicorn 3101 package contains e One Unicorn 3101 VoIP adapter e One universal power supply One Ethernet cable One phone cable 3 PRODUCT OVERVIEW 3 1 Key Features e Supports SIP 2 0 RFC 3261 TCP UDP IP RTP RTCP HTTP ICMP ARP RARP DNS DHCP both client and server NTP PPPoE STUN TFTP etc e B
20. f set to YES then for Attended Transfer the Refer To header uses the transferred target s Contact header information Sets the payload type for DIMF using RFC2833 This parameter specifies the mechanism to transmit DTMF digit in audio which means DTMF is combined in audio signal not very reliable with low bit rate codec Default is YES This parameter specifies the mechanism to transmit DTMF digit via RTP RFC2833 Default YES This parameter specifies the mechanism to transmit DTMF digit via SIP INFO Default is NO This parameter allows users to control whether to send an SIP NOTIFY message indicating the Flash event or Unicorn 3101 User Manual Firmware 1 0 0 46 Page 20 of 28 Last Updated Enable Call Features Offhook Auto Dial Proxy Require Use NAT IP Preferred Vocoder Voice Frames per TX Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY just to switch to the voice channel when users press the Flash key Default is No If set to Yes Call Forwarding amp Do Not Disturb are supported locally This parameter allows users to configure a User ID or extension number to be automatically dialed upon offhook Please note that only the user part of a SIP address needs to be entered here The Unicorn 3101 will automatically append the and the host portion of the corresponding SIP address SIP Extension to notify SIP server that the unit is behind the NAT Firewall NAT IP address used in SIP SDP
21. fer To Use Target Contact DTMF Payload Type DTMF in Audio DTMF via RFC2833 DTMF via SIP INFO Send Flash Event Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY needs to send REGISTER messages to the proxy server The default setting is Yes Default is No If set to Yes the SIP user will be unregistered on reboot This parameter allows the user to specify the time frequency in minutes the Unicorn 3101refreshes its registration with the specified registrar The default interval is 6 minutes The maximum interval is 65535 minutes about 45 days Default is No If set to Yes user can place outgoing calls even when not registered if allowed by ITSP but is unable to receive incoming calls This parameter defines the local SIP port the Unicorn 3101 will listen and transmit The default value for FXS port is 5060 The default value for FXO port is 5062 This parameter defines the local RTP RTCP port pair the Unicorn 3101 will listen and transmit It is the base RTP port for channel 0 When configured channel 0 will use this port value for RTP and the port value 1 for its RTCP channel 1 will use port_value 2 for RTP and port value 3 for its RTCP The default value for FXS port is 5004 The default value for FXO port is 5008 This parameter when set to YES will force random generation of both the local SIP and RTP ports This is usually necessary when multiple Unicorn 3101 are behind the same NAT Default is NO I
22. ification e Support configurable Call Progress Tones e Ultra compact wallet size and lightweight design great companion for travelers e Compact lightweight Universal Power adapter 3 2 Hardware specification Unicorn 3101 LANinterface 1 x RJ45 100MBase T 2 WAN interface 1x RJ45 100MBase T FXS telephone port XEXS a I PSTN Pass Through 1x RII LED light Green and red color 1 Input 100 240VAC 50 60 Hz Universal switching power supply gt Output 5VDC 1200mA CE certification Dimension COMI ESI Es Ta Weight 030kK9 2 S SS LL ARR US 40 130F ee 5 480 MM Humidity 10 996 000000 Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 4 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY 4 INSTALLATIONS The Unicorn 3101 is an all in one VoIP integrated device designed to be a total solution for networks providing VoIP services The Unicorn 3101 VoIP features are available when you connect any regular analog telephone to it Unicorn 3101 has one FXS port labeled Phone and one PSTN pass through port labeled Line After setting up the Unicorn 3101 you can make PSTN calls by pressing 00 Without pressing 00 all your calls will be VoIP You can also receive PSTN calls and VoIP calls The following photo illustrates the Interconnection Diagram of the of a Unicorn 3101 In
23. imer when it receives inbound calls with session timer request Default is NO If selecting Yes the device will use session timer even if the remote party does not support this feature Selecting No will allow the device to enable session timer only when the remote party support this feature To turn off Session Timer select No for Caller Request Timer Callee Request Timer and Force Timer Default is NO As a Caller select UAC to use the device as the refresher or UAS to use the Callee or proxy server as the refresher Default is Omit As a Callee select UAC to use caller or proxy server as the refresher or UAS to use the device as the refresher Default is UAC oession Timer can be refreshed using INVITE method or UPDATE method Select Yes to use INVITE method to refresh the session timer Unicorn 3101 User Manual Firmware 1 0 0 46 Page 24 of 28 Last Updated Special Feature FXS impedance Caller ID Scheme Onhook Voltage Polarity Reversal Hook Flash Timing Volume Amplification Ring Tones TECHNOLOGY Default is NO Choose the selection to meet some special requirements from Soft Switch vendors Default is standard Select the impedance of analog telephone connected to phone port select caller ID to suit standard of different area Select onhook voltage to suit standard of different area or PBX Select Polarity Reversal to adapt some call charge billing system Default is NO Time
24. ing Per Cal i 72 Unconditional Call Forward s To use this feature dial 72 and get the dial tone Then dial the forward oe number and f for a dial tone then hang up 73 Cancel Unconditional Call Forward I To cancel Unconditional Call Forward dial 73 and get the dial tone Deere inenhangup 90 Busy Call Forward To use this feature dial 90 and get the dial tone Then dial the forward number and for a dial tone then hang up BUE eimi ues nel pier Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 11 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY me se Ll ee ee me a ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee 92 Delayed Call Forward To use this feature dial 92 and get the dial tone Dial the forward number and 4 for a dial tone andthenhangup amp 93 Cancel Delayed Call Forward I merne _To cancel this feature dial 93 get the dial tone and then hang up Flash Hook call waiting indication When in conversation without an incoming call this action will switch to a new channel to make a new call qe Dr 5 3 2 PSTN Pass Through When Unicorn 3101 is out of power or loses registration or if the network connection is down the RJ 11 line jack on the side of Unicorn 3101 will function as a pass through connec
25. message Default is blank The Unicorn3101 supports up to 5 different Vocoder types including G 711 A U law G 726 Supports bit rates 32K G 723 1 G 729A B The user can configure Vocoders in a preference list that will be included with the same preference order in SDP message The first Vocoder is entered by choosing the appropriate option in Choice 1 The last Vocoder is entered by choosing the appropriate option in Choice 6 This field contains the number of voice frames to be transmitted in a single packet When setting this value the user should be aware of the requested packet time used in SDP message as a result of configuring this parameter This parameter is associated with the first vocoder in the above vocoder Preference List or the actual used payload type negotiated between the 2 conversation parties at run time e g if the first vocoder is configured as G723 and the Voice Frames per TX is set to be 2 then the ptime value in the SDP message of an INVITE request will be 60ms because each G723 voice frame contains 30ms of audio Similarly if this field is set to be 2 and if the first vocoder chosen is G729 or G711 or G726 then the ptime value in the SDP message of an INVITE request will be 20ms If the configured voice frames per TX exceeds the maximum allowed value the Unicorn 2002 will use and save the maximum allowed value for the corresponding first vocoder choice The maximum value for PCM is 10
26. ng Unicorn 3101 via the LAN port and enable the Enable WAN Web Access option After enabling WAN access be sure that the WAN port of the Unicorn 3101 is connected to an uplink i e router hub switch etc Then get the WAN IP address of the Unicorn 3101 by following section 5 1 of this user manual and selecting menu option 02 Then access the Unicorn 3101 via your web browser by entering the WAN IP address http Unicorn 3101 s IP Address Be sure that your PC is connected to the router hub switch directly or via the LAN port which also serves as a pass through connection for internet network access for your PC of the Unicorn 3101 6 1 4 User Programming and Configuration From your web browser the Unicorn 3101 will show the following login screen Hanlong VOIP Device Configuration Password LL 771 All Fights Reserved Hanlong Technology CO LTD 2005 2008 Enter the password and click on the Login button 6 1 5 Passwords Passwords are case sensitive and all Unicorn devices come with factory default passwords as indicated below Advanced User Password for access to Super User Options admin Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 14 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY End User Password for access to Basic User Options 1234 Pages available for the end user are Device Status Basic Options Additional pagess available to super user are e Super Optio
27. ng same format as above Note NO dial tone will be played between step 1 and 2 Destination ports can be specified by using number TET encoding for followed by the port Examples a If the target IP address is 192 168 0 160 the dialing convention is 47 or Voice Prompt with option 47 then 192 168 0 160 followed by pressing the key if it is configured as a send key or wait 4 seconds In this case the default destination port 5060 is used if no port is specified Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 9 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY b If the target IP address port is 192 168 1 20 5062 then the dialing convention would be 47 or Voice Prompt with option 47 then 192 168 0 160 5062 followed by pressing the key if itis configured as a send key or wait for 4 seconds NOTE When completing direct IP call the Use Random Port should set to NO 5 2 6 Blind Transfer Assuming that call party A and party B are talking to each other on the phone Party A wants to transfer party B to party C Party A presses FLASH on the analog phone or Hook Flash for old model phones to get a dial tone e Then party A dials 87 then dials party C s number and then or wait for 4 seconds Party A can hangs up the phone Note Call features have to be activated during web configuration by selecting YES to Enable Call Features These features need
28. ngs Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 27 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY a Press for voice prompt b Enter 99 and then you will hear the voice prompt Reset c Enter the number 862584658050 A click sound will be heard d Wait for 15 seconds 9 TECHNICAL SUPPORT CONTACT Email Support mail hanlongtek com Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 28 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012
29. ns e FXS port 6 1 6 Configuration Options and Explanations After a correct password is entered in the login screen the embedded web server inside the Unicorn 3101 will show the configuration page which is explained in details below 6 1 6 1 Device Status Setting Options MAC Address WAN IP Address Product Model Software Version System Uptime PPPOE Link Up NAT Port Status DEVICE STATUS Definitions The device ID in HEX format This is a very important ID for ISP troubleshooting This field shows IP address of device This product model is Unicorn3101 Information of software Show system uptime since last reboot Indicates where the PPPOE connection is up if the Uicorn3101 is connected to the DSL modem Indicate the NAT type behind which the device is when the stun feature is defined Indicate the current status of the device such as hook on off registion registered unregistered etc 6 1 6 2 Basic Options Settings Setting options Web Port IP Address Hanlong Technology Co Ltd 1 19 2012 BASIC OPTIONS Setting Definitions The default is 80 There are 3 modes under which the Unicorn 3101 can operate If DHCP mode is enabled then all the field values for the Unicorn 3101 User Manual Page 15 of 28 Firmware 1 0 0 46 Last Updated Time Zone Allow DHCP Option 2 to override Time Zone setting Daylight Savings Time Device Mode LAN Subnet Mask LAN DHCP Base IP DHCP IP Lease Time Port Map
30. s announced Enter 12 digit new IP address if in Static IP Mode ea ee ee eee Eh Rae Tee RI Emm mE mmm mmc DR ETT Er m umm m Um m m ITI TUTTO UE mU T UE EE 2 E m EE T EU D m m EET Tem TT 03 Subnet IP address Other Menu Prompt Features e Just like pressing Hanlong Technology Co Ltd 1 19 2012 kkk Same as Menu option 02 04 Gateway IP address Same as Menu option02 I 05 DNSServer IP address SameasMenuopion i 06 MAC Address Announces the Mac address of the unit 07 Preferred Vocoder Enter 9 to go to the next selection in the i list PCM U e POMA G 726 e G 723 eum al 12 WAN Port Web Access Enter 9 to toggle between enable and mM disable 13 Firmware Server IP Announces current Firmware Server IP Address address Enter 12 digit new IP address 4 4 poo Configuration Server IP NEN Announces current Config Server Path IP Address 0 address Enter 12 digit new IP address _ Hi 5 ERU Upgrade Protocol Upgrade protocol for firmware and configuration update Enter 9 to toggle between TFTP and Se a es Se a i 16 AE Firmware Version Firmware version information h p 17 Firmware Upgrade Firmware upgrade mode Enter 9 to rotate among the following three options ue always check 2 check when pre suffix changes m M 3 never upgrade 47 Direc
31. t Default value is 192 168 22 1 Value is set in units of hours Default value is 120 hrs 5 Days The time IP address is assigned to the LAN clients Forwards a matching TCP UDP port to a specific LAN IP address with a specific TCP UDP port This contains the password to access the Web Configuration Menu This field is case sensitive If set to Yes the Unicorn3101 will respond to the PING command from other computers but it also is vulnerable to the DOS attack Default is No If this parameter is set to No the Http access via WAN port is disabled This field allows users to customize their own code to access PSTN Default is 00 Unicorn 3101 User Manual Page 16 of 28 Firmware 1 0 0 46 Last Updated 6 1 6 3 Setting options Admin Password Layer 3 QoS Layer 2 QoS Data VLAN Tag STUN server keep alive interval Firmware Upgrade and Provisioning Authenticate Conf File SNMP Service Enable SNMP Get Community SNMP Set Community Hanlong Technology Co Ltd 1 19 2012 TECHNOLOGY Super Options Setting SUPER OPTIONS Definitions This contains the password to access the Advanced Web Configuration page This field is case sensitive Only the administrator can configure the Advanced Settings page Password field is purposely left blank for security reasons after clicking update and saved The maximum password length is 26 characters only digit or letter This field defines the layer 3 QoS paramet
32. t IP Calling i Enter the target IP address to make a direct IP call after dial tone See Make TEE S a Direct IP Call 99 ME RESET Enter 9 to reboot the device or Enter MAC address to restore factory default setting See Restore Factory DENN EPUM Default Setting section invalid Entry Automatically returns to Main Menu on the analog telephone you will hear Direct IP Calling Unicorn 3101 User Manual Page 7 of 28 Firmware 1 0 0 46 Last Updated TECHNOLOGY which is just like selecting option 47 from the table above e shifts down to the next menu option e returns to the main menu e 9 functions as the ENTER key in many cases to confirm an option e All entered digit sequences have known lengths 2 digits for menu option and 12 digits for IP address Once all of the digits are collected the input will be processed e Incorrect keyed entry cannot be deleted or undone The Unicorn 3101 will prompt you to start over by telling you that you made an error 5 2 Make Phone call 5 2 1 Calling Phone or Extension Numbers e Dial the number directly and wait for 4 seconds Default is 4 seconds To change the default change the settings via the web configuration page under No Key Entry Timeout Or Dial the number directly and press assuming that Use as Dial Key is set to YES during web configuration of your Unicorn 3101 Other func
33. ternet Network Analog Phone PSTN Pass Through FXS PC A EN Following are the steps to install a Unicorn 3101 e Connect a standard touch tone analog telephone to the Phone port Insert a standard RJ11 telephone cable included with package into the Line port and connect the other end of the telephone cable to a wall jack e Connect a PC to the LAN port of Unicorn 3101 Ethernet cable is included with package Insert another Ethernet cable into the WAN port of Unicorn 3101 and connect the other end of the Ethernet cable to an uplink port a router switch hub modem etc Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 5 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY Insert the powers supply included with package into the Unicorn 3101 and connect it to a power outlet 4 1 Safety The Unicorn 3101 is compliant with various safety standards including FCC CE and C Tick Its power adaptor is compliant with UL standard The Unicorn 3101 should only operate with the universal power adaptor provided in the package Warning Please do not use a different power adapter Using other power adapter may damage the Unicorn 3101 and will void the manufacturer warranty Caution Changes or modifications to this product not expressly approved by Hanlong Technology or operation of this product in any way other than as detailed by this User Manual could void your manufacturer warranty Information
34. tion for PSTN calls Users will be able to use the same analog phone for PSTN calls 5 4 FAX Unicorn3101 supports FAX in two modes T 38 Fax over IP and fax pass through T 38 is the preferred method because it is more reliable and works well in most network conditions If the service provider supports T 38 please use this method by selecting Fax mode to be T 38 If the service provider does not support T 38 pass through mode may be used To send or receive faxes in fax pass through mode users will need to select all the Preferred Codecs to be PCMU PCMA 5 5 Status Light Indicator Following tables show the Unicorn 3101 button light pattern indication Light Indicator Status Meaning Power Light Indicates Power Remains ON when power is connected E second ON then 1 second OFF Indicates device software is running Run Light Fast blinking indicate the product in firmware upgrading or provision Indicate status of the FXS Port on the back panel Busy ON Solid Green Phone Light Available OFF Fast blinking Ringing Slow blinking FXS LEDs indicates voicemail for that port Indicate status of the Line Port on the back panel Busy ON Solid Green Line Available OFF Fast blinking Ringing Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 12 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012 wr PGi EL HANLON G ocr TECHNOLOG 6 CONFIGURATION GUIDE
35. tions available during the call are call waiting flash call transfer and call forward Your SIP gatekeeper proxy server needs to support these features in order for them to work 5 2 2 Call Hold While in conversation pressing the FLASH button on the attached phone will put the remote end on hold Pressing the FLASH button again will release the previously Hold party and the bi directional media will resume 5 2 3 Call Waiting If call waiting feature is enabled while the user is in a conversation he will hear a special stutter tone if there is another incoming call User can press the flash button to put the current call party on hold and switch to the other call Pressing flash button toggles between two active calls 5 2 4 3 way Conferencing Unicorn3101 supports 3 way conference in two styles star code style or Bellcore style Star Code Style 3 way Conference Assuming that call party A and B are in conversation A wants to bring C in a conference Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 8 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012 1 A presses FLASH on the analog phone or Hook Flash for old model phones to get a dial tone 2 A dials 23 then C s number then ff or wait for 4 seconds 3 If C answers the call then A press flash to bring B C in the conference 4 If C does not answer the call A can press flash back to talk to B Bellcore Style 3 way Conference Bellcore style 3
36. to be supported by your SIP gatekeeper proxy server in order to work e Party A can hold on to the phone and wait for one of the three following events 1 A quick confirmation tone temporarily using the call waiting indication tone followed by a dial tone This indicates the transfer is successful transferee has received a 200 OK signal from transfer target At this point party A can either hang up or make another call 2 Aquick busy tone followed by a restored call on supported SIP gatekeeper platforms only This means the transferee has received a 4xx response signal for the INVITE and will try to recover the call The busy tone is just to indicate to the transferor that the transfer has failed 3 Busytone keeps playing This means the Unicorn 3101 has failed to receive the second NOTIFY signal from the transferee and decided to time out Note this does not indicate the transfer has been successful nor does it indicate the transfer has failed When transferee uses a device that does not support the second NOTIFY signal this will be the case In poor or unstable network scenarios this could also happen although the transfer may have been completed successfully 5 2 Attended Transfer Assuming that call party A and party B are in conversation Party A wants to Attend Transfer party B to party C Party A presses FLASH on the analog phone or Hook Flash for old model phones to get a dial tone e Party A then dials part
37. uilt in router NAT Gateway and DMZ port forwarding e Supports call origination and termination from to the PSTN network Powerful digital signal processing DSP to ensure superb audio quality advanced adaptive jitter control and packet loss concealment technology e Support various vocoders including G 711 a law and u law G 723 1 Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 3 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY 5 3K 6 3K optional G 726 32K as well as G 729A B and iLBC Pending e Support Caller ID Name display or block Hold Call Waiting Flash Call Transfer Call Forward in band and out of band DTMF Dial Plans etc e Support fax pass through and T 38 e Support Silence Suppression VAD Voice Activity Detection CNG Comfort Noise e Generation Line Echo Cancellation G 168 and AGC Automatic Gain Control e Support standard encryption and authentication DIGEST using MD5 and MD5 sess e Signaling and call encryption via TLS and SRTP enabling enterprise class security e Support snmp v2 e Support for Layer 2 802 1Q VLAN 802 1p and Layer 3 QoS ToS DiffServ MPLS e Support automated NAT traversal without manual manipulation of firewall NAT and STUN UPNP e Support device configuration via built in IVR Web browser or central configuration file through TFTP or HTTP e Support firmware upgrade via TFTP or HTTP with encrypted configuration files e Support volume ampl
38. way conference is also supported To do this user needs to enable Use Bell style 3 way Conference in FXS web configuration Assuming that call party A and B are in conversation A wants to bring C in a conference 1 A presses FLASH on the analog phone or Hook Flash for old model phones to get a dial tone 2 A dials C s number then ff or wait for 4 seconds 3 If C answers the call then A press flash to bring B C in the conference 4 If C does not answer the call A can press flash back to talk to B 5 2 5 Direct IP to IP Calls Direct IP calling allows two parties that is a FXS Port with an analog phone and another VoIP Device to talk to each other in an ad hoc fashion without a SIP proxy Elements necessary to completing a Direct IP Call 1 Both Unicorn3101 and other VoIP Device have public IP addresses or 2 Both Unicorn3101 and other VoIP Device are on the same LAN using private IP addresses or 3 Both Unicorn3101 and other VoIP Device can be connected through a router using public or private IP addresses with necessary port forwarding or DMZ Unicorn3101 supports two ways to make Direct IP Calling Using IVR 1 Pick up the analog phone then access the voice menu prompt by dial 2 Dial 47 to access the direct IP call menu 3 Enter the IP address using format ex 192 168 0 160 after the dial tone Using Star Code 1 Pick up the analog phone then dial 47 2 Enter the target IP address usi
39. y C s number then or wait for 4 seconds Party A and party Hanlong Technology Co Ltd Unicorn 3101 User Manual Page 10 of 28 Firmware 1 0 0 46 Last Updated 1 19 2012 TECHNOLOGY C now are in conversation e Party A can hang Note When Attended Transfer failed and if party A hangs up the Unicorn 3101 will ring party A again to remind party A that party B is still on the call by pressing FLASH or Hook again will restore the conversation between party A and party B 5 2 8 Make and Receive PSTN Calls Users can send and receive calls from PSTN To receive PSTN calls simply pick up the phone receiver or use handsfree when the analog phone rings To make a PSTN call first press 00 00 is default You can change the PSTN Access Code via the web configuration screen to get the PSTN line dial tone and then dial the PSTN number you want to call 5 3 Call Features 5 3 1 Call Features Tables Following table shows the call features of Unicorn 3101 Call Features 239 _S way conference 787 Blind Transfer 0000000 73000 Block Caller ID for all subsequent calls LL LL 31 Send Caller ID forallsubsequentcall I 67 BlckCalerID prcal s82 0 Send Caller ID per call i 550 o Disable Call Waiting for all subsequent cals 51 oe Enable Call Waiting for all subsequent calls l 70 Disable Call Waiting Per Cal R Enable Call Wait
Download Pdf Manuals
Related Search