MANUAL - Seco-Larm
Contents
1. 6 Do not open or disassemble the camera There are no field serviceable parts inside 7 Do not drop the camera or subject it to strong vibrations Note Many video monitors produce strong electromagnetic fields close to the display CRT especially when the monitor is turned on or during de gaussing which occurs automatically with many monitors when the monitor is turned on Installation 1 Run a 12VDC power supply wire and a video cable with a male BNC connector through the wall to where the camera is to be mounted if necessary 2 Assemble the mounting bracket then screw it into the back of the camera Tighten the adjustment nut 3 Temporarily connect the camera to the 12VDC power supply Do not cut DC jack or female BNC connector as warranty will be voided If needed use the included SECO LARM DC plug with terminal block 4 Temporarily connect the camera s female BNC connector to the video cable s male BNC connector 5 While watching the monitor hold the camera bracket by hand against the wall where it is to be mounted then twist the camera until it is certain that this mounting location is correct Use a pencil to mark the location of the three screw holes in the bracket 6 Disconnect the 12VDC power supply and video cable 7 Mount the bracket to the wall using the three included mounting screws If the wall is made of drywall brick or similar material it may be necessary to use the three inclu2. 1 3 Sony CCD Color e IR Day Night e Weatherproof 24 LEDs e Up to 50ft 15m Range e Split Glass Technology P number coor Ste Ange V Limes Number Color Size Angle TV Lines 420 TV Lines 1 EV 1026 N2GQ DarkGray 29mm 120 420 2 EV 1026 N3GQ DarkGray 3 6mm 92 420 3 EV 1026 N6GQ DarkGray 60mm 53 420 4 Ev 1026 N25Q Siver 5 EV 1026 N3SQ Silver 6 EV 1026 N6SQ Silver 540 TV Lines 1 EV 1606 N2GQ DarkGray 2 EV 1606 N3GQ Dark Gray EV 1606 N6GQ Dark Gray EV 1606 N2SQ 5 EV 1606 N3SQ 6 EV 1606 N6SQ SLI SECO LARM Kas C q Note Model numbers that end with Q or that have a round green Q sticker signify RoHS compliant products ENFORCER 24 LED CCD IR DAY NIGHT CAMERA MANUAL Specifications 1026 N2GQ 1026 N3GQ 1026 N6GQ 1606 N2GQ 1606 N3GQ 1606 N6GQ p 1026 N2SQ 1026 N3SQ 1026 N6SQ 1606 N2SQ 1606 N3SQ 1606 N6SQ 1 3 Sony Super HAD 420 TV lines 540 TV lines Pickup elements 510x492 pixels 768x494 pixels Internal Video output 1 0Vp p composite video 750 Video output NTSC format Minimum 0 lux with LEDs on 0 lux with LEDs on Gaincontrol At S Q APrating o of infrared LEDs Up to 50ft 15m Operating voltage 12VDC 10 70mA LEDs off 90mA LEDs off 250mA LEDs on 250mA LEDs on Operating 4 122 F 20 50 C temperature 311 46 X25 16 x2 94x59x50 mm with sunshield PAL versions also avai
3. the use of this product in violation of any current laws or statutes WARNING Stop using the camera if you see a malfunction such as smoke or unusual heat as it could cause fire or electric shock Do not open the case of this device as there are no field serviceable components inside FCC COMPLIANCE STATEMENT Information to the user This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARRANTY This SECO LARM product is warranted against defects in material and workmanship while used in normal service for a period of one 1 year from the date of sale to the original consumer customer SECO LARM s obligation is limited to the repair or replacement of any defective part if the unit is returned transportation prepaid to SECO LARM This Warranty is void if damage is caused by or attributed to acts of God physical or electrical misuse or abu
4. ded screw anchors 8 Reconnect the 12VDC power supply and video cable Turn the monitor on and make sure the camera is sending the proper video signal 9 To adjust the camera angle loosen and tighten the bracket s thumb screw Turn the camera and change its angle relative to the bracket until the desired scene is displayed 10 Do a final test of the video camera and monitor ENFORCER 24 LED CCD IR DAY NIGHT CAMERA MANUAL Troubleshooting Check that the camera is powered up Check that the power supply s polarity is correct Check that the monitor is powered up Check that the video cable connecting the camera to the monitor is connected properly The screen is blank e Clean the lens using a soft clean cloth Une sce mimage ls at e Check that the light source is adequate e Adjust the monitor s contrast knob The screen image has poor contrast e Change the position of the camera The screen image flickers e Change the position of the camera The screen image is distorted e Change the position of the camera The camera case is hot e Check that the correct power supply is in use IR LEDs do not turn on e Check that the correct power supply is in use IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national state and local laws and statutes related to monitoring and recording audio and video signals SECO LARM will not be held responsible for
5. lable Dimensions Parts List 1 x Manual 1 x Sunshield 3 x Mounting screws 1 x DC plug with 1 x IR camera 3 x Mounting bracket 3 x Screw anchors terminal block lt 3h 94mm Va AE a Say 7 Tie 1 Il WER na i 35mm lan 1 O j AD ENFORCER infrared Day Night 2 A SAO r 50mm ee __ lt lt 13 44mm gt 23h 72mm 25h 59mm gt ENFORCER 24 LED CCD IR DAY NIGHT CAMERA MANUAL a ee 2 Overview A Camera B Adjustable sunshield C Mounting bracket E Thumb screw F DC jack Before Starting 1 Please read this manual carefully and keep it for future reference 2 Use the camera within given temperature and electricity limits 3 Do not aim the LED light directly at the eyes when the LEDs are on 4 Do not point the camera at the sun Heat could damage the camera even when not in use 5 Do not mount the camera in areas exposed to radiation strong magnetic fields or strong electrical signals D 36 0 9m cord Important Do not remove label or OO ay we open case as warranty Se will be voided Female BNC G Adjustment nut connector H DC plug with video out terminal block Connect to video N cable s male BNC connector w yS Important Do not cut DC jack F or female BNC connector G as warranty will be voided
6. se neglect repair or alteration improper or abnormal usage or faulty installation or if for any other reason SECO LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship The sole obligation of SECO LARM and the purchaser s exclusive remedy shall be limited to replacement or repair only at SECO LARM s option In no event shall SECO LARM be liable for any special collateral incidental or consequential personal or property damages of any kind to the purchaser or anyone else NOTICE The information and specifications printed in this manual are current at the time of publication However the SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2009 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM SECO LARM U S A Inc 16842 Millikan Avenue Irvine CA 92606 Website www seco larm com all PICSNs mi EV 1026_EV 1606 docx Tel 800 662 0800 949 261 2999 Fax 949 261 7326 E mail sales seco larm com Made in China
Download Pdf Manuals
Related Search