TM-T70-i User`s Manual - Epson America, Inc.
Contents
1. Paper is jammed A L ca UTION Do not touch the thermal head because it can be very hot after printing Thermal head O lo When paper is jammed never pull out the paper forcibly Open the roll paper cover 27 Opening the Roll Paper Cover on page 10 and then remove the jammed paper 14 English Specifications Item Specification Printing method Thermal line printing Roll paper dimensions Paper width 79 5 mm 0 5 mm 3 13 0 02 Diameter 83 mm 3 27 maximum Inside diameter of core 12 mm 0 47 Outside diameter of 18 mm 0 71 core Thermal paper type NTP0O80 80 Interface Ethernet x1 10BASE T 100BASE TX Serial x1 D sub 9 pin male USB x4 USB 2 0 Type A 5 V 500 mA Micro USB x1 USB 2 0 Micro AB 5 V 500 mA micro SD card x1 Drawer kick out x1 Power supply Dedicated AC adapter AC adapter RA Model M266A DC 24V 1 8 A DC 5 V 2 5 A Dedicated AC adapter AC adapter RA Model M266A Input AC 100 V to AC 240 V 50 Hz to 60 Hz 1 8 A Output DC 24 V 2 1 A DC 5 V 3 0 A AC power consumption Operating 230 V 50 Hz 39 1 W 115 V 60 Hz 39 2 W Standby 230 V 50 Hz 3 2 W 115 V 60 Hz 3 1 W Temperature Operating 5 to 45 C 41 to 113 F Storage 10 to 50 C 14 to 122 F Humidity Operating 10 to 90 RH Storage 10 to 90 RH Overall dimensions Wx Dx H 125 mm x 194 mm x 114 mm 4 92 x 7 64 x2. 4 49 Mass excluding paper and AC adapter Approx 1 8 kg 3 96 Ib 1 500 mA at maximum for one port 2 A at maximum for total of the 5 ports USB and Micro USB ports 2 Available when the PHP function is enabled For information on how to setup PHP environment see TM i Series PHP Setup Manual Be sure to use a micro SD card with the wear leveling function 3 Based on Epson operating conditions 15 English Appendix Downloading Software and Manuals The latest versions of SDK utilities and manuals can be downloaded from one of the following URLs For customers in North America go to the following web site http www epsonexpert com For customers in other countries go to the following web site http download epson biz com service pos Open Source Software License This product uses open source software in addition to Epson proprietary software For information of the open source software used in this product see the following URL http xxx xxx xxx xxx licenses For xxx xxx xxx xxx in the above URL input your printer s IP address Restriction of Use When this product is used for applications requiring high reliability safety such as transportation devices related to aviation rail marine automotive etc disaster prevention devices various safety devices etc or functional precision devices etc you should use this product only after giving consideration to including fail safes and redunda
3. CAUTION L Do not use this product in locations subject to high humidity or dust levels Excessive humidity and dust may cause paper jams and other problems such as fire or electric shock Li Be sure to set this product on a firm stable horizontal surface The product may break or cause injury if it falls L Do not stand on or place heavy objects on top of this product Equipment may fall or collapse causing breakage and possible injury L The print head can be very hot during and immediately after printing If you need to touch it such as for cleaning wait until it cools down Touching it before that may cause burns L Do not connect a telephone line to the drawer kick connector of this product The telephone line or product may become damaged L To ensure safety unplug this product before leaving it for an extended period Caution Labels The caution label on the product indicates the following precautions A L ca UTION Do not touch the thermal head because it can be very hot after printing Also be careful of the autocutter blade near the thermal head A CAUTION When connecting external devices to the USB including Micro USB ports follow the precautions below L Confirm the rated current of the external devices by checking the descriptions on the devices or manuals Connect the external devices only when those total rated current is less than 2 0 A Do not use a device whose r
4. EPSON EXCEED YOUR VISION TM T 70 i User s Manual Important Safety Information page 2 Part Names and Functions 006 page 4 DEED veces ses ETTET NEET TEATATI TEET TTET page 6 Basic Operations ccc ccc cece eee eees page 10 Installing Replacing the Roll Paper page 11 CI GAMING 4 incl spate a Veena dense es ENT page 13 Troubleshooting ccecenee eee eeeaes page 14 Specifica ONS serei raae EE page 15 Appendix ssennsunsnnneseesussesusseen page 16 M00076200EN English Important Safety Information This manual presents important information intended to ensure safe and effective use of this product Read this manual carefully and store it in an accessible location For information on development of a system with this product and setup see also Technical Reference Guide You can access Technical Reference Guide from the included Manual CD Key to Symbols The symbols in this manual are identified by their level of importance as defined below Read the following carefully before handling the product A WARNING Warnings must be observed carefully to avoid serious bodily injury A CAUTION Cautions must be observed to avoid minor injury to yourself damage to your equipment or loss of data Note Notes have important information and useful tips on the operation of your product Safety Precautions A WARNING Ll If this product prod
5. ated current is unclear L Use UL approved external devices only for North American users English Part Names and Functions Manual cutter Roll paper cover ASS LL cover open lever Control panel Power switch Manual cutter Use this cutter when you cut the roll paper manually Roll paper cover Open this cover to install replace the roll paper Power switch Use this switch to turn on or off the printer Cover open lever Press down this lever to open the roll paper cover Control panel L FEED button This button feeds paper LI PAPER OUT LED This LED is on when the paper is near end or out This LED flashes when the printer is in standby L ERROR LED This LED indicates an error lt 3 ERROR LED is on on page 14 or ERROR LED is flashing on page 14 I Power LED This LED is on when the printer is on English Interface All the ports and connectors are located on the back of the printer Drawer kick out connector micro SD card slot Ethernet port Serial port Micro USB port Fo port DC in 24 V connector USB ports DC in 5 V connector Setup Installing the Printer Install the printer horizontally on a flat surface As shown in the illustration install the printer with a maximum tilt of 3 Installing the printer with a tilt of more than 3 may cause the following problems e Roll paper near end cannot be detected e The roll paper cove
6. ctions Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation EPSON is a registered trademark of Seiko Epson Corporation in Japan and other countries regions Other product and company names used herein are for identification purposes only and may be trademarks or registered trademarks of their respective companies Epson disclaims any and all rights in those marks NOTICE The contents of this manual are subject to change without notice 2014 Seiko Epson Corporation All rights reserved 17
7. etach the cover also use a sharp pointed object A WARNING Ifan accident occurs with the power switch cover attached unplug the AC cable immediately Continued use may lead to fire or electric shock English Basic Operations Turning Power On Off Press the power switch to turn on off the printer Note It takes approximately 30 seconds after the printer is turned on until it is ready for printing Opening the Roll Paper Cover Press down the cover open lever to open the roll paper cover 10 English Installing Replacing the Roll Paper Follow the steps below to install replace the roll paper A CAUTION Be sure to use the specified roll paper F Specifications on page 15 1 Open the roll paper cover F Opening the Roll Paper Cover on page 10 2 Remove the used roll paper core if there is one 3 Insert the roll paper in the correct direction 4 Pull out some paper so that the paper is set between the paper guides and close the roll paper cover 11 English 5 Tear off the paper with the manual cutter 12 English Cleaning Cleaning the Printer Case Be sure to turn off the printer and wipe the dirt off the printer case with a dry cloth or a damp cloth A CAUTION Never clean the printer with alcohol benzine thinner or other such solvents Doing so may damage or break the parts made of plastic and rubber Cleaning the Thermal Head To maintain p
8. ncies into your design to maintain safety and total system reliability Because this product was not intended for use in applications requiring extremely high reliability safety such as aerospace equipment main communication equipment nuclear power control equipment or medical equipment related to direct medical care etc please make your own judgment on this product s suitability after a full evaluation 16 English Caution No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Seiko Epson Corporation No patent liability is assumed with respect to the use of the information contained herein While every precaution has been taken in the preparation of this book Seiko Epson Corporation assumes no responsibility for errors or omissions Neither is any liability assumed for damages resulting from the use of the information contained herein Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages losses costs or expenses incurred by purchaser or third parties as a result of accident misuse or abuse of this product or unauthorized modifications repairs or alterations to this product or excluding the U S failure to strictly comply with Seiko Epson Corporation s operating and maintenance instru
9. r will not close after installing roll paper e Roll paper cannot be taken out sirum tilt of 3 Also fix the printer so that it does not move around when you open close the roll paper cover and cut roll paper Note A tape for fixing the printer DF 10 is available as an option English Connecting the AC Adapter Follow the steps below to connect the AC adapter A WARNING Be sure to use the specified AC adapter AC adapter RA Model M266A Connection to an improper power source may lead to equipment damage fire or electric shock 1 Firmly insert the DC connectors of the AC adapter all the way into the 5 V and 24 V DC in connectors on the printer 2 Firmly insert the connector of the AC cable all the way into the AC inlet on the AC adapter 3 Firmly insert the plug all the way into the grounded wall outlet 4 Set the AC adapter so that its label side is facing down English Connecting External Devices If you connect external devices connect each cable to the port connector on the back of the printer lt 2 Interface on page 5 A CAUTION L When connecting external devices to the USB including Micro USB ports follow the precautions below Confirm the rated current of the external devices by checking the descriptions on the devices or manuals Connect the external devices only when those total rated c
10. rint quality Epson recommends cleaning the thermal head periodically generally every 3 months by following the steps below A L ca UTION L The thermal head can be very hot after printing Be careful not to touch it and to let it cool before you clean it L Do not damage the thermal head by touching it with your fingers or any hard object 1 Turn off the printer lt 3 Turning Power On Off on page 10 2 Open the roll paper cover F Opening the Roll Paper Cover on page 10 3 Clean the thermal elements of the thermal head with a cotton swab moistened with an alcohol solvent ethanol or IPA Thermal head 13 English Troubleshooting Power LED does not light Check whether the AC adapter is correctly connected Connecting the AC Adapter on page 7 ERROR LED is on L Check whether the roll paper cover is correctly closed L If the PAPER OUT LED is on check whether the roll paper is correctly installed and any roll paper remains 7 Installing Replacing the Roll Paper on page 11 ERROR LED is flashing L Check whether paper is jammed If it is jammed remove it lt 2 Paper is jammed on page 14 L Printing stops if the thermal head overheats and resumes automatically when it cools For other cases turn the printer off and after 10 seconds turn it back on
11. uces smoke a strange odor or unusual noise immediately unplug the AC cable and then contact your dealer or an Epson service center for advice Continued use may lead to fire or electric shock L Do not use this product with any voltage other than the specified one Doing so may lead to fire or electric shock LI Be sure to use the specified power source Epson AC adapter RA Model M266A Connection to an improper power source may lead to equipment damage fire or electric shock Li Do not connect the cables in ways other than those specified in the manuals Different connections may cause equipment damage or fire L Do not use this product where inflammable fumes of gasoline benzine thinner or other inflammable liquids may be in the air Doing so may cause an explosion or fire L Do not use aerosol sprayers containing flammable gas inside or around this product Doing so may cause fire Li If water or other liquid spills into this product immediately unplug the AC cable and then contact your dealer or an Epson service center for advice Continued use may lead to fire or shock L Do not allow foreign objects to fall into this product Penetration by foreign objects may lead to fire or electric shock L Never attempt to repair this product yourself Improper repair work can be dangerous English L Never disassemble or modify this product Tampering with this product may result in injury fire or electric shock A
12. urrent is less than 2 0 A Do not use a device whose rated current is unclear Use UL approved external devices only for North American users L When using the printer make sure the protective cover fits firmly into place L When Ethernet cables are installed outdoors make sure devices without proper surge protection are cushioned by being connected through devices that do have surge protection Otherwise the devices can be damaged by lightning Note Connecting the optional Wireless LAN Cable Set OT WLO1 to the USB connector enables the wireless LAN connection While connecting via wireless LAN keep the Ethernet cable unconnected to the printer Arranging the Cables When connecting the cables whose connectors do not lock themselves USB cable and DC 5 V cable pass the cables through the cable band to prevent them from coming off Cable band Note When attaching the optional connector cover OT CC70 use multiple cable exits depending on the number of cables After installing make sure the cables are not pinched by the connector cover English Attaching the Power Switch Cover Attaching the enclosed power switch cover prevents inadvertent changing of the power switch and tampering You can turn the power switch on and off by inserting a sharp pointed object in the holes in the power switch cover To d
Download Pdf Manuals
Related Search