User Manual - WeatherConnection
Contents
1. 1 2 inch 1 2 cm 12 USING THE DEVICE 3 Secure closed with the Y fabric fastener S Notes When you take a measurement on the right arm the air tube will be at the side of your y Y elbow Be careful not to rest your arm on the air tube The blood pressure can differ between the right arm and the left arm and the measured blood pressure values can be different OMRON recommends to always use the same arm for measurement If the values between both arms differ substantially please check with your physician which arm to use for your measurements 13 USING THE DEVICE How to Sit Correctly To take a measurement you need to be relaxed and comfortably seated under comfortable room temperature Avoid bathing drinking alcohol or caffeine smoking exercising or eating 30 minutes before taking a measurement Sit on a chair with your feet flat on the floor Sit upright with your back straight e Sit with your back and arm being supported The arm cuff should be placed on your arm at the same level as your heart Taking a Measurement Notes To stop the measurement press the START STOP button once to deflate the arm cuff e Remain still and quiet while taking a measurement 14 USING THE DEVICE 1 Press the START STOP button The arm cuff will start to inflate automatically Y START WINFLATE WDEFLATE WCOMPLETE 0 Oy Se lp 134 y B iel a If your systolic2. Review the sections Before Taking a Measurement and Taking a Measurement Measurement values appear too high or too low 20 MAINTENANCE AND STORAGE Maintenance To protect your device from damage please observe the following e Store the device and the components in a clean safe location e Do not use any abrasive or volatile cleaners e Do not wash the device and any components or immerse them in water e Do not use gasoline thinners or similar solvents to clean the device x 2 oe e Use a soft and dry YG ora 8 and moistened cloth and neutral soap to clean on the monitor and the arm cuff e Changes or modification not approved by the manufacturer will void the user warranty Do not disassemble or attempt to repair the device or components Consult Customer Service D 21 MAINTENANCE AND STORAGE Storage 1 Unplug the air plug from the air jack 2 Gently fold the air tube into the arm cuff Note Do not bend or crease the air tube excessively Do not store the device in the following situations If the device is wet Locations exposed to extreme temperatures humidity direct sunlight dust or corrosive vapors such as bleach Locations exposed to vibrations shocks or where it will be at an angle Optional Medical Accessories Arm cuff Arm circumference 9 17 22 42 cm CD WR17 Model HEM RML31 22 SPECIF
3. 25 less or 25 more Pulse than the average rhythm detected while Blood pressure YI LJNN the monitor is measuring the systolic and diastolic blood pressure If the irregular heartbeat symbol displays with your measurement results we recommend you consult your physician Follow the directions of your physician Movement Error Symbol fj The movement error symbol is displayed if you move your body during the measurement Please remove the arm cuff and wait 2 3 minutes Take another measurement remain still during measurement 2013 ESH ESC Guidelines for the management of arterial hypertension Definitions of hypertension by office and home blood pressure levels Systolic Blood Pressure 2 140 mmHg 2 135 mmHg Diastolic Blood Pressure gt 90 mmHg gt 85 mmHg These are from statistical values for blood pressure KNOW YOUR DEVICE Before Taking a Measurement To help ensure an accurate reading follow these directions 1 Avoid bathing drinking alcohol or caffeine smoking exercising and eating for 30 minutes before taking a measurement Rest for at least 15 minutes before taking the measurement 2 Stress raises blood pressure Avoid taking measurements during stressful times 3 Measurements should be taken in a quiet place 4 Remove tight fitting clothing from your arm 5 Sit on a chair with your feet flat on the floor Rest your arm on a table so that the arm cuff is at the same level as your heart 6 Remain st
4. VP 800 MHz to 2 5 GHz where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer and d is the recommended separation distance in meters m Field strengths from fixed RF transmitters as determined by an electromagnetic site survey should be less than the compliance level in each frequency range Interference may occur in the vicinity of equipment marked with the following symbol gt Note1 At 80 MHz and 800 MHz the higher frequency range applies Note2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the OMRON BP710N is used exceeds the applicable RF compliance level above the OMRON BP710N should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as reorienting or relocating the OMRON BP710N gt Over the frequency range 150 kHz to 80 MHz field strengths should be less than 3 V m 29 GUIDANCE A
5. WARRANTY OMRON SHALL NOT BE LIABLE FOR LOSS OF USE OR ANY OTHER SPECIAL INCIDENTAL CONSEQUENTIAL OR INDIRECT COSTS EXPENSES OR DAMAGES This warranty provides you with specific legal rights and you may have other rights that vary by jurisdiction Because of special local requirements some of the above limitations and exclusions may not apply to you FOR CUSTOMER SERVICE Visit our web site at www omronhealthcare com Call toll free 1 800 634 4350 25 GUIDANCE AND MANUFACTURER S DECLARATION OMRON Automatic Blood Pressure Monitor Information for accompanying documents in the scope of IEC60601 1 2 2007 Model BP710N Important information regarding Electro Magnetic Compatibility EMC With the increased number of electronic devices such as PC s and mobile cellular telephones medical devices in use may be susceptible to electromagnetic interference from other devices Electromagnetic interference may result in incorrect operation of the medical device and create a potentially unsafe situation Medical devices should also not interfere with other devices In order to regulate the requirements for EMC Electro Magnetic Compatibility with the aim to prevent unsafe product situations the IEC60601 1 2 standard has been implemented This standard defines the levels of immunity to electromagnetic interferences as well as maximum levels of electromagnetic emissions for medical devices Medical devices manufactured by OMRON
6. a new one Refer to Optional Medical Accessories ERROR MESSAGES AND TROUBLESHOOTING Repeat measurement Remain still and do not talk during measurement Movement during Refer to Taking a Measurement measurement and the E arm cuff has not been If E2 appears repeatedly inflate inflated sufficiently the arm cuff manually until it is 30 to 40 mmHg above your previous measurement result Refer to Taking a Measurement The arm cuff was inflated exceeding the maximum Do not touch the arm cuff and or allowable pressure and bend the air tube while taking a E 4 then deflated measurement Do not inflate the automatically when arm cuff more than necessary inflating the arm cuff Refer to Taking a Measurement manually Repeat measurement Remain Movement during still and do not talk during measurement measurement Refer to Taking a Measurement Clothing is interfering with G any o interfering the arm cuff wine ame Refer to Using the Device Er Device error Contact Customer Service 19 ERROR MESSAGES AND TROUBLESHOOTING Troubleshooting Replace all batteries with new ones Check the battery installation for proper placement of the battery polarities Refer to Battery Installation No power No display appears on the monitor Blood pressure varies constantly Many factors including stress time of day and how you wrap the cuff may affect your blood pressure
7. pressure is more than 210 mmHg After the arm cuff starts to inflate press and hold the START STOP button until the monitor inflates 30 to 40 mmHg higher than your expected systolic pressure Notes The monitor will not inflate above 299 mmHg A Inflating to a higher pressure than necessary may result in bruising where the arm cuff is applied 15 USING THE DEVICE 2 Remove the arm cuff 3 Press the START STOP button to turn the monitor off The monitor automatically stores the measurement result in its memory It will automatically turn off after 2 minutes Note Wait 2 3 minutes before taking another measurement Waiting between measurements allows the arteries to return to the condition prior to taking a measurement A DO NOT adjust medication based on measurement results from this blood pressure monitor Take medication as prescribed by your physician Only a physician is qualified to diagnose and treat High Blood Pressure A This device is not intended to be a diagnostic device A Always consult your physician Self diagnosis of measurement results and self treatment are dangerous A Inflating to a higher pressure than necessary may result in bruising where the arm cuff is applied 16 USING THE DEVICE Using the Memory Function The monitor automatically stores the results up to 14 sets Note If the memory is full the monitor will delete the oldest value To View the Measurement Values Stored
8. shivering may affect the measurement reading A Do not use the device on the injured arm or the arm under medical treatment A Do not apply the arm cuff on the arm while being on an intravenous drip or blood transfusion A Consult your physician before using the device on the arm with an arterio venous A V shunt A Do not use the device with other medical electrical ME equipment simultaneously A Do not use the device in the area the HF surgical equipment MRI or CT scanner exists or in the oxygen rich environment A The air tube may cause accidental strangulation in infants A Contains small parts that may cause a choking hazard if swallowed by infants IMPORTANT SAFETY INFORMATION A Caution Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury to the user or patient or damage to the equipment or other property General Usage A Always consult your physician Self diagnosis of measurement results and self treatment are dangerous A Consult your physician before using the device for any of the following conditions If you have had a mastectomy Do not take measurements more than necessary lt may cause bruising due to blood flow interference People with severe blood flow problems or blood disorders as cuff inflation can cause bruising A Remove the arm cuff if it does not start deflating during the measurement A Do not use this device on infants or perso
9. 5 Ur gt 95 dip in Ur or 0 5 cycle 40 Ur 60 dip in Ur or 5 cycles 70 Ur 30 dip in Ur or 25 cycles lt 5 Ur 95 dip in Ur or 5 sec Not Applicable Not Applicable Not Applicable Floor should be wood concrete or ceramic tile If floors are covered with synthetic material the relative humidity should be at least 30 Not Applicable Not Applicable Not Applicable Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment Note Ur is the A C mains voltage prior to application of the test level 28 GUIDANCE AND MANUFACTURER S DECLARATION Guidance and manufacturer s declaration electromagnetic immunity OMRON BP710N is intended for use in the electromagnetic environment specified below The customer or the user of this OMRON BP710N should assure that it is used in such environment A IEC 60601 Compli A i F Immunity test test level Electromagnetic environment guidance Portable and mobile RF communications equipment should be used no closer to any part of the OMRON BP710N including cables than the recommended separation distance calculated from the equation appropriate to the frequency of the transmitter Recommend separation distance Conducted RF 3 V rms Not Applicable IEC 61000 4 6 150 kHz to i Radiated RF d 1 2 VP IEC 61000 4 3 80 MHz to 80 MHz to 800 MHz d 2 3
10. Healthcare conform to this IEC60601 1 2 2007 standard for both immunity and emissions Nevertheless special precautions need to be observed The use of accessories and cables other than those specified by OMRON with the exception of cables sold by OMRON as replacement parts for internal components may result in increased emission or decreased immunity of the device The medical devices should not be used adjacent to or stacked with other equipment In case adjacent or stacked use is necessary the medical device should be observed to verify normal operation in the configuration in which it will be used Refer to further guidance below regarding the EMC environment in which the device should be used The MEDICAL ELECTRICAL EQUIPMENT BP710N needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in this documentations The Essential Performance of the BP710N is to measure a blood pressure and a pulse rate and using the memory function The BP710N may be interfered with by other equipment even if that other equipment complies with CISPR EMISSION requirements 26 GUIDANCE AND MANUFACTURER S DECLARATION Guidance and manufacturer s declaration electromagnetic immunity OMRON BP710N is intended for use in the electromagnetic environment specified below The customer or the user of this OMRON BP710N should assure that it is used in such environment Emis
11. ICATIONS Model BP710N REF HEM 7121 Z Display LCD digital display Pressure 0 to 299 mmHg Measurement range Pulse 40 to 180 beats min Pressure 3 mmHg or 2 of reading Accuracy Pulse 5 of display reading Inflation Fuzzy logic controlled by electric pump Deflation Automatic pressure release valve Measurement method Oscillometric method IP classification IP 20 Power source 4 AA batteries 1 5V Battery life Approximately 1000 measurements using new alkaline batteries Operating temperature no o o o humidity 50 F to 104 F 10 C to 40 C 15 to 90 RH Storage temperature o F 909 o humidity air pressure 4 F to 140 F 20 C to 60 C 10 to 95 RH 700 to 1060 hPa Weiaht Monitor Approximately 8 7 8 oz 250 g not including batteries 9 Arm cuff Approximately 6 oz 170 g Monitor Approximately 4 w x 3 1 8 h x 5 1 8 I 103 mm x 80 mm x 129 mm Arm cuff Approximately 5 3 4 x 23 1 2 air tube 29 1 2 145 mm x 594 mm air tube 750 mm Cuff circumference 9 to 17 220 to 420 mm Memory Up to 14 Contents Monitor arm cuff instruction manual quick start guide Dimensions Applied part Type BF Protection against electric shock Notes These specifications are subject to change without notice In the clinical validation study the 5th phase was used on 85 subjects for determination of diastolic blood pressure This device has n
12. ND MANUFACTURER S DECLARATION Recommended separation distance between portable and mobile RF communications equipment and the OMRON BP710N OMRON BP710N is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled The customer or the user of this OMRON BP710N can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and the OMRON BP710N as recommended below according to the maximum output power of the communications equipment Separation distance according to frequency of Output Power of Transmitter transmitter in meter in Watt 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2 5GHz Not Applicable d 1 2 VP d 2 3 VP 12 For transmitters rated at a maximum output power not listed above the recommended separation distance d in meters m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer Note At 80 MHz and 800 MHz the separation distance for the higher frequency range applies Note These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people 30 Manufactured for OMRON HEALTHCARE Co Ltd 53 Kunotsubo Terado cho Muko Kyoto 617 0002 JAPAN Di
13. OMRON INSTRUCTION MANUAL 3 series Blood Pressure Monitor Model BP710N ESPANOL ENGLISH TABLE OF CONTENTS Before using the Monitor e AA TOO 3 Important Safety InformatiON ooonnocccnnnccconoccccononccconancnnonancncnno ca nnnnncnnnannnn 4 Operating Instructions Know Your DEV CE icons rai its Display symbols Before Taking a Measurement ccccceeeeeeeeeeeeeeeeeteeeeeee 10 Preparation sumida heehee Battery Installation hi Using the DeviC8 ooocoooccconnoccccnoncccnoonccconancnnonnncnnonnncnnannncnnannca naar cnn nana ncnnnnns Applying the Arm Cuff ccccccceceeeeeeeeneeeeeeneeeeeeeeeeeeaeeeeeaees 12 How to Sit CorrectlY oooooococnnnocccnnnccccconcccnononcnnnnancnnnnanoncnnancnnnnos 14 Taking a Measurement cccecceeeeeeeeeeeeeeeeeneeeeeneeeeeeneeeees 14 Using the Memory Function oooocccnnoccccnnocccccnoccnconancncnnancnnnnos 17 Care and Maintenance Error Messages and Troubleshooting cooccocnococinocccoconoccnonanccnonnnccnannno 18 Error Messages s tirei cita ecient 18 Troubleshooting Maintenance and Storage Maintenance een doen aaa died Storage ei dannati Optional Medical Accessories Specifications is eases cet as an e na A ITA erat EFCC Stato Meco iria Limited Warranty Guidance and Manufacturer s Declaration INTRODUCTION Thank you for purchasing the OMRON BP710N Blood Pressure Monitor Your new blood pressure monitor uses the oscil
14. ction with the monitor not the tube itself Do not drop the monitor or subject device to strong shocks or vibrations Do not inflate the arm cuff when it is not wrapped around your arm Do not use the device outside the specified environment lt may cause an inaccurate reading Dispose of the device components and optional accessories according to applicable local regulations Unlawful disposal may cause environmental pollution KNOW YOUR DEVICE Contents Monitor arm cuff instruction manual quick start guide Monitor A Display D Battery compartment B START STOP button E Air jack C Memory button Arm cuff F Arm cuff Arm circumference 9 17 22 42 cm G Air plug H Air tube KNOW YOUR DEVICE Display Oi E aa O at 000 CBB O J Irregular heartbeat symbol Movement error symbol Pulse display Memory number Deflation symbol Memory symbol Systolic blood pressure Diastolic blood pressure Low battery symbol Heartbeat symbol Flashes during measurement ZNACLT ovoz KNOW YOUR DEVICE Display symbols Irregular Heartbeat Symbol 9 When the monitor detects an irregular rhythm two or more times during the Normal Heartbeat measurement the irregular heartbeat Pulse A AAAAA symbol will appear on the display with the Blood pressure J LIN SAIS measurement values l TONO An irregular heartbeat rhythm is defined alt Lona as a rhythm that is
15. e free from defects in materials and workmanship appearing within 2 years from the date of purchase when used in accordance with the instructions provided with the monitor The arm cuff is warranted to be free from defects in materials and workmanship appearing within 1 year from the date of purchase when the monitor is used in accordance with the instructions provided with the monitor The above warranty extends only to the original retail purchaser We will at our option replace without charge any monitor or arm cuff covered by the above warranty Replacement is our only responsibility and your only remedy under the above warranty To obtain warranty service contact Customer Service by calling 1 800 634 4350 for the address of the inspection center and the return shipping and handling fee Enclose the original printed receipt Include a letter with your name address phone number and description of the specific problem Pack the product carefully to prevent damage in transit Because of possible loss in transit we recommend insuring the product with return receipt requested THE FOREGOING IS THE SOLE WARRANTY PROVIDED BY OMRON IN CONNECTION WITH THIS PRODUCT AND OMRON HEREBY DISCLAIMS ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IMPLIED WARRANTIES AND OTHER TERMS THAT MAY BE IMPOSED BY LAW IF ANY ARE LIMITED IN DURATION TO THE PERIOD OF THE ABOVE EXPRESS
16. ill and do not talk during the measurement 7 Keep a record of your blood pressure and pulse readings for your physician A single measurement does not provide an accurate indication of your true blood pressure You need to take and record several readings over a period of time Try to measure your blood pressure at the same time each day for consistency 10 PREPARATION Battery Installation 1 Remove the battery cover 2 Insert 4 AA batteries as indicated in the battery compartment 3 Replace the battery cover Notes When the low battery symbol _1 appears on the display turn the monitor off then replace all batteries at the same time Long life alkaline batteries are recommended The measurement values continue to be stored in memory even after the batteries are replaced Dispose of the device components and optional accessories according to applicable local regulations Unlawful disposal may cause environmental pollution 11 USING THE DEVICE Applying the Arm Cuff Remove tight fitting clothing or tight rolled up sleeve from your left upper arm Do not place the arm cuff over thick clothes 1 Insert the air plug into the air jack securely 2 Wrap the arm cuff firmly in place around your left upper arm The bottom edge of the arm cuff should be 1 2 inch 1 to 2 cm above the elbow Air tube is on the inside of your arm and aligned with your middle finger
17. in Memory 1 Press the amp button The Memory number appears for a second before the pulse rate is displayed E n The newest set is numbered 1 E west seis nu 140 2 Press the amp button repeatedly to view the values stored in memory To Delete All the Values Stored in Memory 1 Press the amp button while the memory symbol appears 2 While holding the amp button down press the START STOP button for more than 3 seconds START STOF Note You cannot partially delete the values stored in the memory 17 ERROR MESSAGES AND TROUBLESHOOTING Error Messages Irregular heartbeats are detected Movement during measurement The batteries are low The batteries are exhausted Air plug disconnected Arm cuff is applied too loosely Air is leaking from the arm cuff 18 Remove the arm cuff Wait 2 3 minutes and then take another measurement Repeat the steps in Taking a Measurement If this error continues to appear contact your physician Carefully read and repeat the steps in Taking a Measurement You should replace the batteries with new ones ahead of time Refer to Battery Installation You should replace the batteries with new ones at once Refer to Battery Installation Insert the plug securely Refer to Using the Device Apply the arm cuff tighter Refer to Using the Device Replace the arm cuff with
18. lometric method of blood pressure measurement This means the monitor detects your blood movement through your brachial artery and converts the movements into a digital reading An oscillometric monitor does not need a stethoscope so the monitor is simple to use Intended Use This device is a digital monitor intended for use in measuring blood pressure and pulse rate in adult patient population The device detects the appearance of irregular heartbeats during measurement and gives a warning signal with the measurement result Uli Please read this instruction manual thoroughly before using the device Please keep for future reference For specific information about your own blood pressure CONSULT YOUR PHYSICIAN IMPORTANT SAFETY INFORMATION A Warning Indicates a potentially hazardous situation which if not avoided could result in death or serious injury General Usage A DO NOT adjust medication based on measurement results from this blood pressure monitor Take medication as prescribed by your physician Only a physician is qualified to diagnose and treat High Blood Pressure A The monitor is not intended to be a diagnostic device A Consult your physician before using the device for any of the following conditions common arrhythmias such as atrial or ventricular premature beats or atrial fibrillation arterial sclerosis poor perfusion diabetes age pregnancy pre eclampsia renal diseases Note that PATIENT motion trembling
19. ns who cannot express their intentions A Do not use the device for any purpose other than measuring blood pressure A Use only the approved arm cuff for this device Use of other arm cuffs may result in incorrect measurement results A Do not use a mobile phone or other devices that emit electromagnetic fields near the device This may result in incorrect operation of the device A Do not disassemble the monitor or arm cuff This may cause an inaccurate reading A Do not use in a location with moisture or a location where water may splash on the device This may damage the device A Do not use the device in a moving vehicle car airplane A Read If your systolic pressure is more than 210 mmHg of this instruction manual if your systolic pressure is known to be more than 210 mmHg Inflating to a higher pressure than necessary may result in bruising where the arm cuff is applied IMPORTANT SAFETY INFORMATION Battery Usage A Do not insert the batteries with their polarities incorrectly aligned A Use only 4 AA alkaline or manganese batteries with this device Do not use other types of batteries Do not use new and used batteries together A Remove the batteries if the device will not be used for three months or more General Precautions Do not forcibly crease the arm cuff or the air tube excessively Do not press the air tube while taking a measurement To unplug the air plug pull on the air plug at the conne
20. ot been validated for use on pregnant patients Internally powered ME equipment 23 FCC STATEMENT FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 24 LIMITED WARRANTY Your BP710N Automatic Blood Pressure Monitor excluding the arm cuff is warranted to b
21. sions test Compliance Electromagnetic environment guidance The OMRON BP710N uses RF energy only for its RF emissions internal function Therefore its RF emissions are very CISPR 11 low and are not likely to cause any interference in nearby electronic equipment RF emissions Harmonic The OMRON BP710N is suitable for use in all emissions Not Applicable establishments including domestic establishments IEC 61000 3 2 and those directly connected to the public low voltage power supply network that supplies buildings used for Voltage A domestic purposes fluctuations flicker emissions 1EC61000 3 3 Not Applicable 27 GUIDANCE AND MANUFACTURER S DECLARATION Guidance and manufacturer s declaration electromagnetic immunity OMRON BP710N is intended for use in the electromagnetic environment specified below The customer or the user of this OMRON BP710N should assure that it is used in such environment IEC 60601 Electromagnetic Immunity test Compliance level test level environment guidance Electrostatic discharge ESD IEC 61000 4 2 Electrical fast transient burst IEC 61000 4 4 Surge IEC 61000 4 5 Voltage dips short interruptions and voltage variations on power supply inputlines IEC 61000 4 11 Power frequency 50 60 Hz magnetic field IEC 61000 4 8 kV contact kV contact 2 kV for power supply lines 1 kV for input output lines 1 kV line s to line s 2 kV line s to earth lt
22. stributed by OMRON HEALTHCARE INC 1925 West Field Court Lake Forest IL 60045 U S A www omronhealthcare com 2013 OMRON HEALTHCARE INC Made in Vietnam 2298789 0C
Download Pdf Manuals
Related Search