Manual NetEye ENG_v1.0
Contents
1. List of video cameras to be selected Event list displays the list of events alarms in the last 30 days for the selected video camera in the area below Click a Motion Alarm event to directly open the recording O If no events occurred the area is empty Snapshot opens the folder with selected video camera snapshots Administrator only Dimens True displays the recording with actual image dimensions 4 Position Manual positioning in the recording To playback a recording 1 Double click a video camera 1 2 Set the end of the search period 2 and click Search or select the recording from the list 3 3 Playback the recording 4 To display snapshots 1 Double click a video camera 1 2 Click Snapshot the system folder 2 with the snapshots taken by that video camera appears To save files to a USB key under Windows drag them to the device VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 23 TELEDATA oK NetEye Client To playback a recording from video cameras that were or were not set E Aires Leena h oft it B 1 Select a video camera and click or 2 Click NVR and enter the address playback password and video camera index Result the recording playback panel opens 3 Set the end period for the search 1 and click Search 4 Playback the recording 2 v Normally set video cameras are any Ste2. 1 1 Graphic concepts Graphic concepts adopted in the text are illustrated below Page concepts Example Description This indicates a chapter section paragraph table or Italic See paragraph illustration heading in this manual or other publication of reference lt text gt Zann 7 This indicates a text that may have a specific value In YYYY gt the example this could be 13082006 oga The representation of an object on the screen i e 11 menus tables etc VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 1 aF TELEDATA K Note important information highlighted after the text they refer to Warning operations to be carefully performed or important information ao Suggestions practical information for good function operations 1 2 Warranties and technical support Warranty Teledata is not liable for direct or indirect damages to people or property restrictions due to software settings other than those described in this manual Qualified personnel must install this software strictly following the instructions in this manual and according to local laws standards and safety regulations in effect For further information on warranty conditions please refer to the purchase terms and warranty instructions available at www teledata i com Technical This manual was drafted with care and is intended for qualified personnel support For any ques
3. NetEye NVR PROFESSIONAL Client Server settings Remote Client INSTALLATION AND USER MANUAL Information ownership COPYRIGHT 2011 Teledata s r l All rights reserved Any full or partial distribution modification or reproduction of this document is prohibited without written authorization by Teledata s r l except the following actions e Fully or partially printing the document in its original format e Transferring the document on web sites or other electronic systems e Copying content without editing it and quoting Teledata s r l as the owner of the copyright NOTE thus the content of this document cannot be used to develop other content for your retail purposes without written authorization by Teledata s r l Requests for additional copies of this product or pertinent technical information should be addressed to Teledata s r l 20132 Milan Italy Via G M Giulietti 8 Tel 39 02 27 201 352 39 02 25 92 795 Fax 39 02 25 93 704 E mail info teledata i com Declaration of conformity This software application was designed according to the quality reliability and performance criteria adopted by Teledata The software application must be installed according to the instructions in this manual The NetEye software application is compatible with Windows7 and Windows XP operating systems CONTENTS 1 General information 1 1 1 Graphic concepts 1 1 2 Warranties and technical suppo
4. To change or delete a Preset position select it and click Change or Delete UL 11 6 Recording and holiday calendar settings Purpose For the selected video camera the Time Ranges panel lets you e program recordings on a weekly schedule e set holidays on a yearly basis Holidays are shared by all functions based on time ranges A see chapters 11 7 Enabling video camera display and recording 11 8 Recordings or output activation on events 11 9 Motion Alarm Settings Path Homepage Time Ranges double click the video camera VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 40 aF TELEDATA O Digig araa ap Sema 4 a De Meragar Mein Sema AT Seaman rara g De iE a vibra p raran ogging re neo wee ee Ae nD ek Dd ob oe ov ow os ow on oe i E 5 E bec h To program recordings for the selected video camera 7 Set recording time ranges see aa i Lii r F Bei or Pr iy Serer ac ST ia r L Pi al m FI chapter 7 4 The weekly EEEE EA A calendar 2 Click SET to save data 3 Enable the video camera to record in the RecDisplay panel VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 41 ar TELEDATA K To set holidays for the selected video camera 1 In Holidays select a date to be changed or a free one 00 00 using the c
5. E a x MESA y VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 51 a TELEDATA oK DELE Description Types of IP connections to be set Teledata Teledata IP video cameras Teledata VideoServer 4 ch 4 channel Teledata video servers SteelEye VideoServer 16 ch NetEye Client only 16 channel SteelEye NetEye Server video cameras in a LAN are directly A accessible with their IP address and password Use Remote Client in a WAN without fixed IP see chapter 14 Remote Client Video camera or video server IP address The IP address must belong to the same domain as the A computer where NetEye is installed Ch1 Ch2 Ch3 Stream type primary or secondary to be used for the video camera Ch4 Ch1 or channel selected by the Video Server where the images are displayed i e to playback on 3G ae Select a format compatible with the video camera features connections a format with less detail is recommended NetEye Client only SteelEye video camera channels to be displayed UDP NetEye Client only for connections to SteelEye TCP UDP protocol only used in a LAN TCP protocol typically used in a WAN SteelEye only allows two different types of connections UDP A and TCP simultaneously To access video cameras or video servers via http LAN or WAN Password Video camera Name displayed in the tree chart Name VIDEO SURVEILLANCE SYSTEM NETEYE
6. 4 Use the IP Channels function to specify the user name and password if you want to use the Online video camera setup function 5 All video camera images are now visible Login settings Where necessary data access and machine settings can be password protected See chapter 9 2 Password settings In those countries where privacy laws are in effect this A settings phase is mandatory VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 31 a7 TELEDATA oK 11 Standard NetEye Server settings 11 1 Introduction Following is the suggested standard NetEye settings sequence Step Description Chapter to read 1 Searching for connected video cameras 11 2 Searching for connected video and assigning IP addresses cameras and assigning IP addresses General settings and the creation of a 11 3 General settings virtual monitor for Remote Client if necessary Main settings for each fixed video 11 4 Fixed video camera settings camera 4 Main settings for each Speed Dome 11 5 Speed Dome video camera video camera and Preset and Tour settings position settings Programming recordings for time 11 6 Recording and holiday calendar ranges for each video camera and settings holiday settings Selecting video cameras for continuous 11 7 Enabling video camera display and recording or turning off all video recording cameras 7 Recording and input setti
7. SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 35 Monitor Quality a TELEDATA o Description Playback image quality on Remote Client virtual monitors 100 maximum image quality The value affects the transmission BitRate between NetEye and Remote Client High image quality leads to higher band use or saturation Remote Client virtual monitor resolution VGA 640 x 480 XGA 1024 x 768 To set Remote Client virtual monitors 1 Select one of the 10 virtual monitors 1 2 Select the number of splits for the monitor 2 3 Enter the number of the video camera for each enabled split 3 11 4 Fixed video camera settings Purpose NetEye Client Path The Video Camera Setup panel lets you e view video camera network settings e set playback image quality and features This panel lets you calibrate your playback image quality needs to the real transmission band capacity You can set the best quality fluidity and error control for the most important video cameras only leaving essential image display to more service video cameras so as not to saturate available band Streaming values are directly read by the selected video camera For advanced settings see chapter 12 4 Advanced video camera settings In NetEye Client the purpose of this panel is to show change the selected video camera IP address and index Homepage Video Camera Set
8. camera playback Purpose NetEye Server settings The following is possible with Remote Client e display images acquired from IP video cameras set in NetEye Server virtual monitors in real time e save a snapshot Both image quality depending on NetEye Server quality settings and refresh frequency can be set To set NetEye Server for connection from Remote Client 1 Install NetEye Server and set as normal 2 Create up 10 virtual monitors and assign a video camera to each split 3 Assign a public IP address to NetEye Server 4 Set Remote Client to connect to the NetEye Server IP address VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 5 7 1 In Host Name IP enter the NetEye Server IP address and set 5900 as the default port number 2 Click Save settings data is saved 3 Click on the monitor for image playback and set quality 1 and refresh frequency 2 4 Click gt to start playback Playback can be stopped using B and the displayed image saved by clicking w Quality and refresh frequency must be suited to the available band VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 58 TELEDATA oK Main offices 20132 Milan Italy Via G M Giulietti 8 Tel 39 02 27 201 352 39 02 25 92 795 Fax 39 02 25 93 704 E mail info teledata i com Central Southern Italy Offices 56010 Ghezzan
9. firmware IP video cameras can be simply viewed in the network with a Ke browser Consider that one video camera can accept up to 10 connections Description The function opens the application homepage in a browser that directly manages the video camera Please see the video camera user manual Path e Homepage double click a video camera 2 user name and password for video camera access ra eis Jakova Byfrsl Sheree J sme t ff eee jF ee i rr E p a LALU Wo Bo 7 m o ppm ee ri e i iz Bad S i a E f Aa 7 fn el A 5 _ VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 54 TA oQ 13 NetEye Client 13 1 Interface and functions Purpose Interface NetEye Client lets you view images and playback recordings from video cameras connected to several NetEye Servers and several SteelEye in real time The NetEye Client interface is identical to NetEye Server Only the following panels are enabled Section Enabled functions panels Chapters 8 2 Selected image snapshot 8 4 Recording playback and snapshot display NetEye setup add NetEye 11 3 General settings Server IP address memos settings a Password NetEye Client 9 2 Password settings protection Messages NetEye Client 11 10 Display messages alarm event and log messages a Events NetEye Client events 11 11 Display daily alarm event log IP Channels add IP vid
10. oK Test the outputs 1 To test the relay board or video ee ee ee ee camera digital output select one or more relays to be activated 1 2 Click On to switch the relays and digital output om ma o 11 9 Motion Alarm Settings Purpose The Motion Setup panel lets you e turn on Motion Detection only in some time ranges e set up to three Motion Detection areas be enabled to record in the RECDisplay panel While they Video cameras that only record on Motion alarm should not A can record in the Event Management panel Path Homepage Motion Setup double click a video camera Description Managing Motion alarms saves disk space For information on how to set time ranges see chapter 7 4 The weekly calendar VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 46 aF TELEDATA oK ee ee ee Description Video Settings Standard filters to be applied to images acquired by the video camera Brightness Contrast Saturation SetRng lt numero gt Displays the area for Motion Detection and allows sensitivity to be edited in To set a motion detection area 1 4 Set standard filters 3 5 Click Enable 1 in the area Set the time range when the Motion alarm is enabled Select the area to be set 1 and set sensitivity Identify the area drag it and size it by dragging the borders 2 Click Set
11. 48 12 NetEye Server Advanced settings 50 12 1 Introduction 50 12 2 Display IP video camera information 50 12 3 Manual video camera addressing 51 12 4 Advanced video camera settings 54 13 NetEye Client 55 13 1 Interface and functions 55 13 2 Configuration 55 14 Remote Client 57 14 1 Remote video cammera playback 57 VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE II aF TELEDATA K 1 General information This manual NetEye installation and user manual e Version 1 0 e Month and year of print January 2012 Information on NetEye software version 1 1 x software Manual This manual is addressed to the following individuals addressees System This person has full access to NetEye functions administrator Specifically this person assigns login passwords to Operator and Playback profiles As the surveillance system administrator this person controls and exports recordings lf authorized they can edit installation settings Operator This person has full access to system functions except for recording playback and delete functions Playback This person can playback recordings Network This person designs the network installs video administrator cameras and optional devices installs video camera NetEye Server and routing settings Network design and hardware A installation are not illustrated in this manual since considered skills already known to the administrator
12. Application and scope Introduction NetEye is a professional Client Server NVR Network Video Recorder that acquires video images from local video cameras in a LAN with IP address lt also supports video servers up to four channels to connect analog video cameras For special architectures the same video cameras can also ve viewed from remote using the Remote Client software Network design the choice of devices and materials i e computers cables and switches must be accurate to guarantee the necessary image quality for highly surveilled areas This software only supports Teledata video cameras NetEye Server For minimum installations simply install NetEye Server connected to a ina LAN maximum of 64 video cameras in a LAN each distinguished by an IP address A relay board extends the ability to control remote devices other than those controlled by the output on the single video camera For each NetEye Server video camera e immediately view and record acquired images e playback recordings e manage the input and output Internet 10 virtual monit r i i r i NetEye optional Server W vided w P 64 IP Camera aia at re i web server ay B IIN gt LIN gt O Oo 2 WO wW WA A E S E S ia Em A A d NetEye Server LAN Architecture VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 4 a7 TELEDATA oK NetEye Fo
13. ION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 19 aF TELEDATA K 8 System monitoring 8 1 Introduction This chapter describes typical surveillance operator functions To View the chapter Open NetEye 7 2 Changing the Access level Change the video camera image 7 3 Actions on video camera images Take a snapshot of the monitor image 8 2 Selected image snapshot Acknowledge an alarm 0 Alarm acquisition Playback recordings or view snapshots 8 4 Recording playback and snapshot display 8 2 Selected image snapshot Purpose Save a frame of the playback video Description A snapshot can be taken at any time from the selected video camera The saved image can be displayed and used in the Playback panel See chapter 8 4 Recording playback To take a snapshot of the video camera image 1 Select the video camera 1 or a image 2 2 Click wa the snapshot is saved ir TOL VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 20 a7 TELEDATA oK 8 3 Alarm acquisition Purpose Description Mute any buzzers or interrupt actions started by triggered alarms When an alarm from inputs or outputs or image analysis triggers i e Motion Detection a red LED turns on under the acquisition button lf set alarms can trigger external devices i e a buzzer The alarm and its acknowledgement are logged in the log file Impulse relays do not require alarm acknowledge
14. L INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 29 aF TELEDATA ON To export recordings for one or all video cameras to CD DVD 1 Set the CD DVD and copy 1 L features Laava Set the concerned period select one or all video cameras 2 and click Search the calculated value with any overflow messages 3 appears Click Burn to copy VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 30 a7 TELEDATA K 10 NetEye Server settings 10 1 Introduction This chapter describes typical installer functions To View the chapter Learn how to prepare for installation 10 2 Installation assumptions Standard NetEye Server settings 11 Standard Advanced NetEye Server settings 12 NetEye Server 10 2 Installation assumptions First installation Video cameras must be addressed after completing software installation addressing Following is the typical first installation procedure 1 Set the progressive IP address directly on the video camera before installing it being sure that it belongs to the same domain as the computer where NetEye is installed 2 Install and connect all the video cameras any sensors or connected devices 3 Using the Find IP video cameras on the network function let NetEye find all video cameras and assign them a name and stream features on the channel If some video cameras were connected with factory set IP addresses edit them
15. MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 52 TA To add video cameras with IP addresses already set 1 N Enter the video camera or video Select either video camera or video server 1 server IP address and type of stream for the channel 2 2 Enter the video camera or video server user name and password and name to be assigned 3 Click New the video camera or 3 video server channel IP address is added to the end of the list To change video camera or video server settings click on the IP address edit settings and click Change To delete a video camera from programming click on the IP address click Delete Deleted appears in the list etEye Client To add a connection to a Enter the SteelEye IP address 3 Select the channels to be E i Select 1 Steel Eye VideoServer 16 ch z l displayed and type of protocol 2 Click New the SteelEye IP i i i x r address is added to the list as many times as there are selected channels If necessary select the single channel edit settings and click Change4 VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 53 CERI E o popopo TELEDATA a TELEDATA K 12 4 Advanced video camera settings Purpose The Online video camera setup panel lets you e Display all video camera settings e set advanced settings e update
16. MOTEPLAYBACK Data security guaranteed recorded via CRC and CRYPTO several level password administration compatible with domestic Privacy regulations Control of up to a maximum of 64 Teledata video cameras of four channel Teledata Video Servers Connection via Ethernet cable locally Connection and data routing via IP protocol in remote Up to ten virtual monitors with maximum 64 split each Transmission protocol management e UDP TCP e HTTP Video quality and band use parameter management e Resolution e Bit Rate e FrameRate 1 25 fps e Jitter in playback Video streaming compression algorithms e H264 e MPEG4 Independent video controls Bright Contrast Sat Hue for each channel Circular recording VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 9 TELEDATA oK Speed Dome video cameras Recording Video camera settings Virtual Monitor Playback Digital inputs outputs Remote control Data export Speed Dome local connection via Ethernet cable Remote PTZ position control 16 position rotating Tour settings Timed recording length after a movement or input signal Weekly and holiday calendar management to enable recordings Recordings also in formats SXGA 1280x960 SXGA 1400x1050 HD 720 and HD 1080 Online access to video camera firmware for advanced parameter settings Up to 10 virtual monitors 49 split each to view images f
17. Motion to save Motion settings Click SET to save VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 47 a7 TELEDATA oK 11 10 Display alarm event and log messages Purpose Path Show all alarm and event messages on all video cameras signaled during the last week For details on events and alarms filtered by day or video camera use the Events panel Homepage Messages HDC Leeper Saip aliser Seb lE moe rer dione Lvant Mioboo tosh Saatup edie urera Meneue ep bvenk Caralh l as F kH E coc Ti wi Bell et tar r an Fa l nee i1 12 mm9 Evel rah 11 par Th eae F IT Fay Il m 11 Tms a 117 Fy J Ad F E Ere aia 112 mE LEL F TI F 7 l Ei i 12 2 Byal oo 1 Tis m T hi TA r nl Ex al Hl 12 f ay 112 F 3 Esel POF ioe 1 i mE Lyall ane rn rei a CY apga 2E Rabon karima OS AS IE mm Fam l argir R S 11 11 Display daily alarm event log Purpose Description Path The Events panel lets you e view alarms recorded on the selected day e search alarms events by type e search alarms events by part of the message text The function displays the alarm and event log for the selected video camera saved due to e Motion alarms e video camera input alarms Homepage Events double click the video camera VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 48
18. Open NetEye 7 2 Changing the Access level the program Change the video camera image 7 3 Actions on video camera images Set times ranges in the weekly calendar 7 4 The weekly calendar Administrator only 7 2 Changing the Access level Purpose lf passwords were set the access level can be changed at any time If passwords were not set the system is fully accessible and the change login level function does not appear See chapter 9 2 Password settings for functions enabled disabled for each level Path Homepage am Login Logout 7 3 Actions on video camera images After installation setting passwords to protect both setting data and recordings is recommended Description The image acquired by the video camera can be directly edited as you please without altering settings List of Following is a list of possible actions oat Zoom in Enlarge or shrink the image al Zoom out Original Size Return the image to its original size Full screen Same as button BR displays the full screen image Jitter time Display delay Version not used 1 0 23 0 Path Right click each displayed image in the various NetEye panels VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 1 7 aF TELEDATA od 7 4 The weekly calendar Purpose The weekly calendar is used in various functions to start recording e only in certain time ranges Time Range panel e In certain time ranges but consequ
19. YSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 13 a7 TELEDATA oK Description The video camera type is identified by an icon e EF fixed video camera fe Speed Dome Video camera details show the following data XXX XXX XXX XXX IP address Teledata brand RecON enabled and recording video camera The RecOFF recording can also be viewed on the monitored channel red box StreamON video camera connected with image flow in StreamOFF progress DispON video camera connected with image flow in DispOFF progress enabled for view The panel displays a tree diagram with all connected video cameras I IOE EEEE TE noon E LLALA To view video camera status details 1 Double click the video camera to view its status VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 14 TELEDATA oK 6 2 Video camera display Purpose The images acquired by the video cameras in split mode for up to 64 channels simultaneously are displayed in the homepage and single images can be changed The following operations are not permitted e Changing the position view mode split full screen e Changing some features in each image see chapter 7 3 Actions on video camera images Description Following are the functions available through buttons Button Description Example of a button with split number From nine to 64 Work with the
20. aF TELEDATA K PETF fahr Aala Fara Li 2 ee oe ee Fi Ca yA DELE Description Day in which alarms events are displayed See ALL Displays logs for all video cameras for the selected day Camera Allows events alarms to be selected by type on the selected video camera a Motion displays alarms generated by Motion analysis only I O shows events linked to video camera inputs and outputs Events shows system events not classified as alarms i e login video camera unavailable All displays all alarms events saved for the selected video camera To search for an alarm event on a specific video camera 1 l Select the day 1 PE Cae n M Same SAri Dea Maca TE Tereri Drin e ei Mihara a UAN ee vers a 2 Select the video camera 2 3 3 Select the type of alarm event 3 2 4 Enter the text to be searched and click Search 4 5 Continue searching by clicking Next VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 49 aF TELEDATA K 12 NetEye Server Advanced settings 12 1 Introduction Following are functions that help with advanced settings To View the chapter Display all video camera settings 12 2 Display IP video camera information Set video camera channels assigning a user name and 12 3 Manual video camera password for advanced settings addressing Set special parameters or update video camera 12 4 Advanced video
21. camera firmware settings 12 2 Display IP video camera information Purpose The NetEye Status function displays all settings read by the selected video camera To display and edit all video camera settings see chapter 12 4 Advanced video camera settings Use this window to check settings requested by Teledata customer service f a ai Path Home page TE E E l HEREHERE Oar ee a VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 50 ar ELEDA 12 3 Manual video camera addressing Purpose NetEye Client Description Path The IP Channels panel lets you e add new video cameras with a previously set address e assign a user name and password and set primary or secondary stream on video cameras already in the network For NetEye Client the IP Channels panel lets you connect to e IP video cameras and video servers whether or not conencted to NetEye Server typically in a LAN e SteelEye LAN and WAN This function is useful when adding video cameras installed with a correct IP address or when setting access data and stream type To find all connected video cameras see chapter 11 2 Searching for connected video cameras and assigning IP addresses Home page 5k48 IP Channels REGi Garren Sot PTS Scheels ect Hasara Hon Sec HA te Frcs Loam Er 1 rama Fihn cup esi Gonads en Gum le PPL aw 1
22. elEye cameras while an IP address can be entered for NetEye cameras VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 24 aF T ELED 9 System Administration TA E 9 1 Introduction This chapter describes typical system administrator functions To View the chapter view the chapter Set passwords 82 Password settings Set passwords 9 2 Password settings 9 2 Password settings Purpose The panel lets you set three protected system login levels e System administrator Privacy Guarantor e Operator event alarm calendar settings e Playback lf no access level is set the system provides free access to all functions helpful during installation Login after setting levels Otherwise the no login level is active and many system functions are not enabled In those countries where privacy laws are in effect this settings A phase is mandatory The Operator and Playback login levels are available after setting the Administrator level After completing installation set passwords to protect data and recording settings VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 25 a7 TELEDATA oK Description Functions enabled for the various access levels are listed below Administrator or Playback Operator no password peo __ E a E control Alarm acquisition in progress Configuration m Display v
23. ent Server mode e set some general settings i e language e test relay boards optional e set up to 10 virtual monitors for Remote Client NetEye Client In NetEye Client this panel is used to add NetEye Server memos for image playback n Path Home page NetEye Setup VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 34 o Data Description NVR Server NetEye works like a Server Requires PC reboot mode NVR Client NetEye works like a Client Requires PC reboot The connected NetEye mode server IP addresses can be manually entered as a memo only RTSP Player Player mode in client version leave selected Language Set the interface language Local Output select the COM port connected to the optional relay board see chapter Module 11 8 Recordings or output activation on events Check press this button to check for the board To identify the number of the COM port connected to the A device use the Windows Device Management application NVR IP NetEye Client only IP addresses and names assigned to the NetEye Address server to be connected to Recording Fixed disk or partition where video recording and snapshot files are Target saved Delete Images Days permitted by privacy regulations to keep recordings before erasing after Days them privacy 0 record until disk full then overwrite oldest data x number of recording days VIDEO
24. ent to an input signal Event Management panel e in certain time ranges but consequent to triggering a sensitive area in the position Motion Setup panel Description The weekly calendar is divided in time ranges represented by several five or 30 minute time intervals Following is the color key Interval Description Red oOo o The half hour is set for recording Green The half hour is not set for recording The half hour is partially set for recording Click io display details er a os Hri eens mee eee E tf fT ft ff Le tar a a N Scheduling Mri To set a weekly schedule 1 Click an interval 1 on one day in eee 5 sess Se eee the week Mon Tue or holiday SSS Hol to turn recording on off in that half hour See chapter 11 6 Recording and holiday calendar G settings VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 18 aF TELEDATA K To set time ranges with periods under a half an hour 1 Click an interval 1 on one day in mou ow a b E v w F w n o G A o the week or holiday a A NE ES SR E OES ST OEE Click amp 2 details on the half an SSS Sr hour divided in five minute el intervals appeals 3 a seo Scheduling Mri 3 T Select the intervals to turn T SIE SSS a See recording on off in that period za El a ml Gnd Gat God Rm Col God Ral Ct Ca VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLAT
25. eo 12 3 Manual video cameras video server and camera addressing SteelEye Video camera Setup video 11 4 Fixed video camera settings camera settings 13 2 Configuration Preface The following information is required e NetEye Server IP video cameras and SteelEye IP addresses to be connected e NetEye Server communications port and any playback password e indexes of video cameras connected to each NetEye Server VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 55 aF T ELED Recommended Following is the suggested standard NetEye settings sequence procedure TA oQ Step Description Panel Added NetEye Server IP addresses to NetEye setup connect to memo only Za Added SteelEye IP video camera or IP Channels video servers to connect to NetEye Server playback settings and Video Camera video camera indexes Setup Two NetEye Client can run on the same computer to control up to 64 64 IP cameras VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 56 TA oQ 14 Remote Client Introduction Installation Remote Client is a simple application to playback images from video cameras linked to 10 virtual monitors set in a NetEye Server NetEye Setup Connect to a NetEye Server via IP address At the end of installation the icon appears on the ae desktop and the program launches 14 1 Remote video
26. er i e 5 TLC gate NetEye Client In a Client installation the function finds the following in a LAN e IP video cameras e video servers Any connections to SteelEye must be specifically added in the IP Channel panel Path Home page VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 33 a TELEDATA oK Description IP address Video camera or video server IP address and any Gateway for output on Net Mask Gateway The IP address must belong to the same domain as the WAN computer where NeiEye is installed For video server channels will have the same address The channel and name must be set for each channel Stream Video camera IP Cam or Video Server CHx stream type The IP address belongs to a video camera Video Server The IP address belongs to the selected video server channel CHx To find and add connected video cameras to NetEye cameras appear as they are found 1 2 Select the video camera or video server channel 1 to be added to NetEye 3 Enter the required addresses and name 2 1 Click Show connected video enee E 4 Select the stream type and channel 3 5 Click Update and then Add to NVR the video camera is set with the new address and added to the e list of video cameras 11 3 General settings Purpose The NetEye Setup panel lets you e change Cli
27. execution delete item NVRLauncherUpdate NetEye can only be started from the installation folder Create a link on your desktop to open the program when needed To uninstall NetEye 1 In the windows toolbar click icon the 7 maintenance request window appears 2 Select NVR Maintenance 3 Delete the folder where NetEye was installed VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 12 6 What NetEye looks like Introduction The homepage is divided in various control and command areas Description It appears at start up and is always displayed on secondary application pages Area 6 1 PERE CeaeS ir TELEDATA Description Chapter List of connected video cameras and their 6 1 Connected video camera conditions status Display of connected video cameras with 6 2 Video camera display up to 64 different chanel splits and relevant split controls Speed Dome controls 6 3 Speed Dome controls Playback functions NetEye 8 System monitoring administration and settings Functions are _ l 9 System Administration enabled according to the login level Administrator Operator Playback 10 NetEye 3 Image editing controls 7 3 Actions on video camera images Connected video camera status Purpose Lets you e view connected video cameras e check each connected video camera status i e recording display VIDEO SURVEILLANCE S
28. for a configuration of about 64 channels CPU Level Intel Core I7 Refer Intel 17 920 2 66G Cache 8M FSB 4 8 GHz DRAM 3G VGA 512MB Video Ram Network Interface Card 10 100 1000 Ethernet OS Support Windows XP Windows 7 Windows Server 2003 Windows Server 2008 VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 7 TELEDATA Band requirements o Video Setting VGA 30 FPS 1M 40 64 Ch VGA 20 FPS 60 64 Ch Bandwidth Data size Resolution 1 Ch 4 Ch 16 Ch 32 Ch 64 Ch D1 VGA 2 MB 8MB 32 MB 64MB 128 MB CIF 1 5 6MB 24MB 48MB 96MB Frame Rate MB PAL 25 FPS 1MB 4MB 16MB 32 MB 64MB NTSC 30 768K 3 MB 12MB 24MB 48 MB FPS 512K 2MB 8 MB 16 MB 32 MB 384K 1 5 MB 6MB 12MB 24MB 256K 1 MB 4 MB 8 MB 16 MB az bold VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 8 Note A GB switch is required for band values marked in TA oQ 4 Main features Surveillance Guaranteed simultaneous functions Security and privacy Device connection Alarms e Motion detection e Digital input activation Video input masking function Privacy e Access area filtering e Timed recording System log for e Alarms e Events e Errors e Device activities i e login REC RTV PLAYBACK VIDEOSERVER RE
29. ideo camera info Playback Export data Path Home page H Elri cere Sogn n Soden adang O veni roger eich ab HEH Maap F eee bs aana 2 ewe 2 eae VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 26 aF T ELED TA E To set a password 1 Enter the password in each profile 2 Click SET the system opens in the no login level 3 Click EXIT click E in the homepage to open NetEye with the required level 9 3 Exporting recordings to USB keys Purpose Description Path The panel lets you export recordings available for one or more video cameras to a USB key To save files to CD or DVD use the CD DVD burn function Based on the selected period the system displays the video cameras that made recordings Some video cameras can be unselected before export Use the Calculate dimension function to obtain the A necessary space on the removable device s Homepage Backup to USB key VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 27 a7 TELEDATA K rei ye a oT bii Mn Eaa Area Description a Area where the recording interval is set and necessary space is calculated 2 List of video cameras to be included in the saved file Area where necessary and available space is calculated and the saving procedure started and progress monitored To save several recordi
30. ment To acquire an alarm 1 Click 1 the red LED under the button disappears PAPUE HE ENHE EN BHEWEE SOR Hoan a TELEDATA 8 4 Recording playback and snapshot display Purpose Description The panel lets you e Playback all saved recordings e Review the video camera events and directly open the concerned recording e View snapshots and copy them to other support devices U Only the Administrator can copy snapshots Each video camera enabled to record creates about 8 minute files The number of recordings depends on both the recording settings and disk capacity typically five days of recordings VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 21 aF TELEDATA O NetEye Client This panel lets you playback recordings from e IP video cameras and video server typically in a LAN e SteelEye previously set in the IP Channel panel A memo can be added for all connected NetEye Server IP addresses in the NetEye Setup panel Path Homepage Playback Area Description i List of eight minute recordings on the hard disk Media files amount of recordings currently on file Currently selected recording Start End first and last recording date time Recording search area date and time VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 22 aF TELEDATA O Description
31. minimum split required for the number of installed video cameras for the best image definition and size Display the selected image in full screen mode Double click to display the homepage show the selected image only Example of a button for one two or four zoomed positions and mime other smaller ones im _ Show only four positions CIC To assign a video camera to an image 1 Select the video camera 1 and drag it to the selected channel 2 lf a displayed video camera is dragged to an occupied channel the images switch 4 He Boe Ej Hannah ar TELEDATA VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 15 a7 TELEDATA K 6 3 Speed Dome controls Purpose To direct the selected Speed Dome position from remote or use a list of set positions Speed Dome controls Element Description Zoom Enlarge or shrink the frame Strada To adjust a Speed Dome 1 Select the Soeed Dome name 1 or Speed Dome image 2 2 Select one of the default positions 3 or move the virtual joystick to adjust the Speed Dome I LLLE facaas ar TELEDATA VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 16 aF TELEDATA od 7 Shared NetEye concepts 7 1 Introduction This chapter describes the functions shared by all profiles or that appear in several points in View the chapter
32. nd time on images in both playback and recording VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 37 aF TELEDATA o Description Network Main video camera setting display Video Settings Standard filters to be applied to images acquired by the video camera Client Playback NetEye Client only selected video camera IP address name and index Data is automatically updated for video cameras connected to SteelEye 11 5 Speed Dome video camera settings The PTZ Setup panel lets you Purpose e setup to 16 Preset positions e seta Tour of maximum 16 Preset positions Path Homepage wik PTZ Setup double click the video camera Description Preset positions can be selected during playback in channels See chapter 6 3 Speed Dome controls SHSSSESSSSSCRCCe LUES DELE Description Enable PTZ Recognizes the selected video camera as a Speed Dome and enables Camera x all panel controls VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 38 Data Tour aF TELEDATA K Description Virtual joystick used to position and size the Speed Dome position U move up L move left R move right D move down S stop Speed Dome movement Zoom IN Zoom OUT size Stop stop resizing Use the cursors on the sides of the video channel in alternative e Top 1 zoom e Side 2 up down e B
33. ngs 1 Insert the USB key me 2 Click Select or Unselect and click a on the single video cameras to be 2 3 included excluded from export _ L 1 3 Set the period 2 and click 3 Calculate dimension the calculated value appears in Source 3 4 Click Explore to select a specific folder 5 Click Start to copy aa VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 28 aF TELEDATA O 9 4 Exporting recordings to CD or DVD Purpose The panel lets you save available recordings for one or all video cameras to CD or DVD O To save files on a USB key use the Backup to USB key function R W support content can be deleted from this panel Description The system calculates the space needed to save one or all video camera recordings and graphically displays it compared to loaded CD DVD capacity Use the Search function to obtain necessary space on the A CD DVD Abort and Erase Disk functions can only be applied to R W supports Path Homepage a e l M MUMM _e Description Area where the type of CD DVD is indicated Area where the recording interval and video cameras to be exported is indicated and where necessary space calculations is requested Area where necessary and available space message area save procedure and save progress is checked Signals space exceeding the loaded volume VIDEO SURVEILLANCE SYSTEM NETEYE MODE
34. ngs or 11 8 Recordings or output activation on activating an output when an input or events motion alarm triggers for each video camera Recording and Motion alarm settings for 11 9 Motion Alarm Settings each video camera Furthermore the following log and alarm control functions are described Description Chapter to read Displaying alarms events and log messages 11 10 Display alarm event and log ET T Displaying the alarm event log 11 11 11 11 Display daily alarm eventlog daily alarm event log VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 32 TELEDATA oK 11 2 Searching for connected video cameras and assigning IP addresses Purpose The Find IP video cameras on the network panel lets you e add new video cameras fixed or Speed Dome or video servers to the network assigning them the correct IP address The ACTi board shows ACTi video cameras in the network and their settings but does not let you add them to NVR Description On first installation this function helps you to find all connected video cameras that have either a correct IP address or factory set address Use this function first to find and add video cameras If ie access data and the type of stream need to be set use manual video camera settings See chapter 12 NetEye Server Enter the position of the video camera in the tree diagram in its name this makes all setting operations easi
35. ns TestR1 TestR2 TestR3 TestR4 switches the relays in the optional board to test mode Test Out switches the selected video camera digital output seconds Length of the recording started by the digital input on the selected video camera VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 44 _ any TELEDATA To program recording on an event or in a certain time range 1 Set the time range in which event management is enabled 2 Click Norm Closed Input 1 if required by the sensor type 3 Enter the appropriate value in Recording length on I O 2 a 4 Click SET to save data L a a To enable a device connected to the video camera 1 Set the time range in which event vw ewe ee ee ee nn management is enabled 2 Select whether the output is enabled by a motion alarm or when the input is activated 1 3 Set the length of output activation name 2 od 4 Click SET to save data To activate a device connected to NetEye with the relay board optional 1 Set motion parameters in the rn ra ne ee CTE Motion Setup panel 2 Select the relays for the areas set in Motion alarm management 3 Set the length of output activation 2 4 Click SET to save data E VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 45 TELEDATA
36. o Pisa Via Carducci 64 Tel Fax 39 050 87 87 25 E mail pisa t teledata i com Middle East Office Dubai Airport Free Zone 3 East Wing 4 Floor PO Box 54620 Dubai Tel 971 0 42149670 Fax 971 0 42149501 E mail info teledata i com VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 60
37. ottom 3 left right Set set up to 16 Preset positions Goto Select one of the 16 Preset positions Name the Preset position Assign a name to each Preset position Set a tour of maximum 16 positions Pos 1 16 number of the Preset position to be added replaced deleted Time 1 99 seconds duration in the position Speed 10 99 seconds speed of movement from one position to the next New add the indicated Preset position to the Tour Change change the selected Preset position with the one indicated Delete remove the selected Preset position RUN run the tour VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 39 aF TELEDATA O To set a Preset position 1 set the required position with the am z joystick 1 or cursors 2 2 In Preset click on the position aca 2 number Set 3 3 3 Pees De Lees Lees ee Ds J Select Name the Preset position GHGoCGGGOSRHSEGo and enter the name i e North gate 3 camera to a position click To move the video a the number Goto To set and test the Tour 1 Set the Preset positions using the previous procedure 2 In Pos 1 16 1 enter the number aa of the Preset position and in Time gt 1 99 and Speed 10 99 the soossoceceeeeces duration and switch speed 3 Click New to add a position to the a Tour 4 Repeat points 1 to 3 for all required positions 5 Press RUN to test the Tour
38. r more complex installations where more than 64 video cameras need Client Server to be controlled several NetEye Servers can be installed connected in a ina LAN network to a NetEye Client NetEye Client displays the video cameras with IP addresses regardless of whether or not they are connected to a NetEye Server and playback the recordings from the various servers in the system Two NetEye Client can run on the same computer to control up to 64 64 IP cameras NetEye m i Client PLAYBACK Fi i Diino a l a NetEye SteelEye Server J lt 64 IP cameras 16 cameras NetEye Client Server LAN Architecture NetEye Server For installations that require the remote display of images Remote Client with Remote software can be installed in the remote workstation and up to 10 virtual Client WAN monitors can be created in NetEye Server that display the images of the 64 video cameras Remote Client connects to NeyEye Server via a public IP address of DNS Remote Client ei a sa T a i lt 10 virtual monitor 10 virtual monitor ao a NetEye NetEye Server Server a gt nee u i pmi i i L a L NetEye Server with Remote Client Architecture WAN VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 5 TELEDATA oK NetEye Client NetEye Client can be used to playback recordings from one or more Steel for remote E
39. rom Remote Client Recording date and time field search Snapshot display in jpg format Video camera input output on off control Four relay expansion board optional to manage motion alarms Full video camera settings via web USB key DVD VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 10 TELEDATA oK 5 Installation software 5 1 Net Eye Server or Client Installation Introduction NetEye is supplied on CD in a self installing exe file that includes both the Server and Client versions Description NetEye installation can be used to install e Server to record view and playback video cameras in a LAN e Client to playback one or more NetEye If the computer is accidentally shutdown the software does not automatically reboot e Client24h to playback one or more NetEye If the computer is accidentally shutdown the software automatically reboots To install NetEye Client or Server 1 Double click NetEye exe and specify a different f Extracto xi folder to copy files to if necessary EA RDE e aetess Eure Aun Winzip 2 When finished click OK codecs and necessary eA xi components are installed 7 O CANetEye W Overwrite file l W When done a For automatic Microsoft packet Atnstalll exe updates complete them and if the next window does not appear launch Installer exe from the installed folder e c NetEye7 to continue the in
40. rt 2 1 3 Information on privacy 2 2 Application and scope 4 3 Installation requirements 7 4 Main features 9 5 Installation software 11 5 1 Net Eye Server or Client Installation 11 6 What NetEye looks like 13 6 1 Connected video camera status 13 6 2 Video camera display 15 6 3 Speed Dome controls 16 7 Shared NetEye concepts 17 7 1 Introduction 17 7 2 Changing the Access level 17 7 3 Actions on video camera images 17 7 4 The weekly calendar 18 8 System monitoring 20 8 1 Introduction 20 8 2 Selected image snapshot 20 8 3 Alarm acquisition 21 8 4 Recording playback and snapshot display 21 9 System Administration 25 9 1 Introduction 25 9 2 Password settings 25 9 3 Exporting recordings to USB keys 27 9 4 Exporting recordings to CD or DVD 29 VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 10 NetEye Server settings 31 10 1 Introduction 31 10 2 Installation assumptions 31 11 Standard NetEye Server settings 32 11 1 Introduction 32 11 2 Searching for connected video cameras and assigning IP addresses 33 T13 General settings 34 11 4 Fixed video camera settings 36 11 5 speed Dome video camera settings 38 11 6 Recording and holiday calendar settings 40 11 7 Enabling video camera display and recording 42 11 8 Recordings or output activation on events 43 11 9 Motion Alarm Settings 46 11 10 Display alarm event and log messages 48 11 11 Display daily alarm event log
41. stallation 153 file s unzipped successfully 3 Select the type of installation Z imaste j 4 CI ick Next Beng eea E cde A hT a Sere ee rar Pie l bee ee CH eels r eaii CO gima 5 Confirm dll installation until the installation is successfully completed without errors f i vegeme decir statin A 6 Click OK ae A A Crortuiapere mpa p VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 11 TELEDATA 7 From menu Start Programs Automatic Bra execution select NVRLauncherUpdate NetEye launches and the main window opens l 8 Channels appear darkened since the video cameras e e were not yet set See chapter 10 NetEye NetEye will automatically open one eae aa a whenever the computer is turned on To close NetEye and or shutdown the computer 1 When exiting NetEye click Yes to close NetEye and shutdown the computer or No to exit NetEye only To start the computer without launching NetEye 1 In the windows toolbar click icon the 2 wvniouncher x A NWRLauncher versione 1 0 maintenance request window appears l DRES PET os ee 2 Select NVR Maintenance 3 Click Minimize NetEye will not be launched the next time the computer is started to permit maintenance i e data disk cleaning W Manutenzione NVR To permanently delete automatic NetEye launch 1 From menu Start Programs Automatic
42. that signals the motion alarm e Test digital outputs on the video camera or optional relays Video cameras that only record on event should not be enabled to record in the RECDisplay panel While they can also record on Motion alarm Motion Setup panel U The video camera only records after an event Events are recorded in the log file See the Messages and Events panels Recording on event saves disk space Homepage 1 Event Management double click the video camera VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 43 a7 TELEDATA oK u i t 7 aa a i ms ime oF n Fi if H EF 1 ia iS th iF if 43 fal r E7 F Digital Inputs Digital Outputs Recording length on I O Description Norm Closed Input video camera digital input idle when grounding closed Digital outputs activated by different types of input signals No output activation output disabled Enabled from Motion Detection output enabled when the selected video camera Motion Alarm triggers See chapter 11 9 Motion Alarm Settings Enabled from Input output enabled by the activation of a digital input on the selected video camera Length seconds length of output activation NVR Rele lt number gt activates the relay lt number gt on the relay board optional when the motion alarm triggers in area lt number gt i e NVR relay 1 triggers when area 1 is in alarm conditio
43. tions or special technical requests please contact our personnel Please write or call to contact personnel able to answer your questions and provide assistance Service email laboratorio teledata i com Service phone number 39 0227201352 int 22 Service fax number 39 022593704 1 3 Information on privacy Regulations There are specific regulations in some countries on personal data acquisition storage and processing NetEye is included in this context when it records and stores images We suggest you refer to that indicated in the governmental sites documents in the country where the equipment is installed to ensure that its use does not violate these criteria Privacy NetEye has specific functions to customize the way this data can be management recorded stored and consulted to guarantee their protection in countries with NetEye where required See chapter 9 2 Password settings VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 2 Compliance with Italian regulations Liability TA oQ For Italy NetEye meets Legislative decree 675 96 Personal and individual data processing protection as further amended The images in this equipment cannot be modified in any way Teledata is not liable for the incorrect use of recorded personal data VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 0 1 2012 ENG PAGE 3 ar TELEDATA K 2
44. up double click the video camera VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 36 aF TELEDATA K Lisboa Teip Taema Ee F kora es ieee bami Moien Eee Tip Pe eee Mera beri ore IF ALC S671 Chup Ca 2 Image video camera resolution BitRate band used by the video camera A high value indicates higher quality and higher band use Frame Rate frames acquired per second UDP User Datagram Protocol protocol not focused on connection quality but used when reliability is not the primary target The advantages of UDP are the speed and lower network congestion than TCP no confirmation packets and the possibility of transmitting in multicast sending a packet to a group of hosts and broadcast mode sending a packet to all hosts in a network segment UDP protocol works well in a local network but may fail if used in a larger network TCP Transport Control Protocol network protocol par excellence TCP IP set the routing rules for data packets along the entire network it ensures that all packets sent to a remote computer actually reach their destination HTTP transmission protocol with control on the connection between the sender and receiver Set Jitter Video playback delay helpful in reducing band congestion in the event of network orverload U It does not affect recording image fluidity Show Date amp Time Displays the current date a
45. ursor 2 In Month Selector move the cursor to the holiday month 3 In Day Selector move the cursor to the holiday day 4 Click SET to save data l 4 m E 11 7 Enabling video camera display and recording Purpose The RECDisplay panel lets you start end video camera recordings according to a time range Time Ranges panel enable display and turn off a video camera for maintenance Video cameras used for recordings based on Motion A alarms Motion Setup panel or on Events Event Manager panel should not be enabled in this panel Path Home page FH TELEDATA Data Description VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 42 Data Record x Show x Disable x All recording None recording aF TELEDATA K Description Enable disable the video camera x for display on main monitor and or recording Disable video camera display recording and event management Select unselect all video cameras for recording 11 8 Recordings or output activation on events Purpose Path The Event management panel lets you e Start recording for a certain duration when the input connected to the video camera is activated The input is activated according to the set time range e Activate the video camera output after at least one motion alarm or when the video camera input activates e Activate optional relays for the area
46. yes connected in a LAN or WAN and one or more IP video cameras SteelEye use connected in a LAN VIDEO SURVEILLANCE SYSTEM NETEYE MODEL INSTALLATION AND USER MANUAL Ver 1 1 1 2012 ENG PAGE 6 aF TELEDATA K 3 Installation requirements Preface Tips Minimum requirements for systems up to 12 channels Minimum requirements for systems up to 64 channels Network design and the choice of computers where NetEye Server Clients are installed must be accurate to guarantee the necessary image quality for highly surveilled areas Installation must be performed by qualified personnel who are A fully aware of the needs of this type of system Given that only qualified personnel can correctly install a network of IP video cameras following are some generic tips e Use a network separate from the company network e Use aPC with capacities suited to video camera needs e Use category 6 cables for gigabyte networks e Use switches suited to the network if gigabyte Following are the requirements for a configuration of about 12 channels CPU Level Atom Core Duel Refer Intel Atom 330 1 6G Cache 512K FSB 533 MHz DRAM 1G VGA On Board Intel 945GC Network Interface Card 10 100 Ethernet OS Support Windows XP Windows 7 Windows Server 2003 Windows Server 2008 Video Setting VGA 30 FPS 1 9 Ch 1M VGA 20 FPS 1 12 Ch 512M Following are the requirements
Download Pdf Manuals
Related Search