K6 Camera User`s manual
Contents
1. 3 Installation Do not apply power to the camera before completing installation Please install the proper power cut off device during the installation connection Always follow the instruction guide the manufacturer recommended If this product is installed in the ceiling please make sure the installation position can sustain the min 50N 4 Qualified engineers needed All the examination and repair work should be done by the qualified service engineers We are not liable for any problems caused by unauthorized modifications or attempted repair 5 Environment This series camera should be installed in a cool dry place away from direct sunlight or strong light inflammable explosive substances and etc This series camera shall work on the specified working temperature Please keep it away from the electromagnetic radiation object and environment Please keep the sound ventilation Do not allow the water and other liquid falling into the camera 6 Accessories Be sure to use all the accessories recommended by manufacturer Before installation please open the package and check all the components are included Contact your local retailer ASAP if something is broken in your package 7 Daily Maintenance Please shut down the device and then unplug the power cable before you begin daily maintenance work 111 Use the dry soft cloth to clean the device If there is too much dust please use the water to dilute the mild deter2. power cable to the device 4 Menu 4 1 HDAVS Series DVR Settings Note The following operation and interfaces for reference only Please refer to the HDAVS series DVR user s manual for detailed information After connected the camera to the HDAVS series DVR from Main Menu gt Setting gt System gt PTZ you need to set control mode as HDAVS and the protocol as DH SD1 Click Save button to save current setup See Figure 4 1 GENERAL mae Channel CO y Bee Control Mode HDCVI D PTE Protocol DH SD1 D ATMIPOS UNOS C ACCOUNT Baudrate EXT A AUTO MAINTAIN Data Bits IMP EXP Stop Bis MO DEFAULT Parity None UPGRADE Figure 4 1 On the preview interface right click mouse and then select PTZ you can see an interface shown as below See Figure 4 2 Figure 4 2 Click Iris to open menu or confirm current operation Click up down button to view all the items on the left pane of the following list Click left right button to set the corresponding values on the right pane of the following list If there is tal click confirm button to go to the 2nd menu Repeat the previous steps to set detailed value Click Return button to go back to the previous menu interface Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Pb Hg Cd Cr VI PBB PBDE Circuit Board A 3 o s 2 a Component Device Construction O o O o o o Material Wire and Cab
3. HDAVS Fixed Camera User s Manual Version 1 0 0 Table of Contents 1 Generali ducto E ha 1 1 DV CIICW anana a na a cea daessuasanaionrsaceasatense nea naeteaiete 1 2 A aunts ea esp dela at a ttn suet a a e a eeu a aS 2 Framework and DIMCGMSIONS A eee a installations Sch steht ats Snot teat Dn ptovsl sea otc E E Pasties ee E e E ome Suave 4y MENU eee ere arte eRe ree Rr ror Pree arte tre tier ry Stent EP ere E E E Pe Dror Teen We Ra pte yee oes 4 1 HDAVS Series DVR Settings cial Appendix Toxic or Hazardous Materials or Elements ooooooooniccncnociocononcnonconconnonn nono nonoconocnnos Welcome Thank you for purchasing our HDAVS camera This user s manual is designed to be a reference tool for your system Please read the following safeguard and warnings carefully before you use this series product Please keep this user s manual well for future reference 11 Important Safeguards and Warnings 1 Electrical safety All installation and operation here should conform to your local electrical safety codes The power shall conform to the requirement in the SELV Safety Extra Low Voltage and the Limited power source is rated 12V DC 24V AC in the IEC60950 1 We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation 2 Transportation security Heavy stress violent vibration or water splash are not allowed during transportation storage and installation
4. gent first and then use it to clean the device Finally use the dry cloth to clean the device Please put the dustproof cap to protect the CCD CMOS component when you do not use the camera 1v Applicable model This manual can be applied to following model AVS B2210 1 General Introduction 1 1 Overview This series megapixel HD camera conforms to the HDAVS standard It supports video signal high speed long distance transmission without any delay It can be controlled by the DVR conforming to the HDAVS 1 2 Features High performance CMOS image sensor megapixel definition Support HD video and control signal coaxial transmission Support 75 3 coaxial cable transmission without any loss 720P series transmission distance over 500m 1080P series transmission distance over 300m High speed long distance real time transmission Support HDAVSHD and analog SD switch output 720P series support 720P 25 720P 30 720P 50 720P 60 1080P series support 1080P 25 1080P 30 720P 25 720P 30 720P 50 720P 60 Support high performance 3D noise reduction denoise excellent performance in low illumination Support ICR switch to realize surveillance both in the daytime and at night 3 6mm fixed lens 2 8mm 6mm 8mm optional Support OSD on screen display suitable for user self defined setup Support DC12V power supplying IP66 compliance Support intelligent IR function max IR distance 20m 2 Framework and Dimensions Please
5. le O o O o o o Packing X E 5 T 3 Components Accessories o o o o o o O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T 11363 2006 standard X Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ T11363 2006 standard During the environmental friendly use period EFUP period the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these substances or elements will not result in any severe environmental pollution any bodily injury or damage to any assets The consumer is not authorized to process such kind of substances or elements please return to the corresponding local authorities to process according to your local government statutes Note e This manual is for reference only Slight difference may be found in the user interface e All the designs and software here are subject to change without prior written notice e All trademarks and registered trademarks mentioned are the properties of their respective owners e If there is any uncertainty or controversy please refer to the final explanation of us e Please visit our website or contact your local service engineer for more information
6. refer to the following figures for dimension information The unit is mm See Figure 2 1 to Figure 2 4 154 7 65 0 80 0 Figure 2 1 Sunshade Cover Video Port Cover IR Light pena SD HD Switch Control Cable Figure 2 2 When the standard definition high definition switch control cable is short circuit system outputs standard definition video Otherwise when the circuit is open system outputs the high definition video 3 Installation Important e Before the installation please make sure the installation surface can sustain at least 3X weight of the bracket and the camera Step 1 Dig three holes in the installation surface of the wall or the ceiling Insert three expansion bolts to the three holes and then lock firmly Installation surface Bracket Camera Figure 3 1 Step 2 First prepare the cable according to the cable Line up the three screw holes at the bottom of the bracket to the three installation holes in the wall or the ceiling and then insert three screws to the three holes of the chassis of the bracket and fix them firmly Now secure the bracket on the installation surface of the wall or the ceiling Step 3 Adjust the camera to the proper monitor area via the three directions indicated in Figure 3 2 after you fixed the camera Figure 3 2 Step 4 Connect the device video output port to the terminal devices such as the DVR NVS and etc Then connect the
Download Pdf Manuals
Related Search