EZ240 User Manual
Contents
1. attached to the housing base under the camera which is designed to absorb any moisture trapped inside the housing during adjustment To avoid excessive moisture build up it is recommended that the camera not be installed in rainy or excessively damp conditions It is also advisable to limit the number of times the housing cover is removed The desiccant pack can be replaced if condensation develops inside the housing EZ220 Series Picture element Horizontal resolution Sensitivity S N ratio Electronic shutter Gamma correction Video output Power source Sync Mode Lens mount Dimension Operating temperature JJ EverFocus INSTRUCTION MANUAL 512 x 492 NTSC 512 x 582 PAL 340 TV Lines 1 3 Color outdoor WaterProof Camera 2 0 lux F 1 2 I General Over 48 dB The EZ220 series of cameras contain a CCD camera in a stylish and attractive waterproof housing EZ220 series uses a high sensitive 1 3 color interline transfer CCD sensor with low lux performance it is available in two versions Up to 1 100 000 gt 0 45 a Model EZ220B with board lens available in f 3 6mm f 4 3mm f 6 0mm f 8 0mm format b Model EZ220M with CS mount can use any C and CS mount 1 3 format manual iris lens excluding varifocal lenses Auto iris lenses can not be used with the model 1 0Vp p 75 ohm 12VDC 10 300mA Internal Sync ll Precautions e Do not expose the camera to humidity and dust If th2. the housing cover from the back plate Please pay attention to prevent damage to the O Ring seal c Loosen the lens mount fixing screw located at side of the lens by using the L wrench supplied d Adjust the lens to bring the subject into focus Secure the lens mount fixing screw firmly again f Overlaying the cover gently in order to prevent damage to the O Ring and camera components Notes A Make wiring connections only after it has been determined that power has been disconnected Use only a 12VDC power supply for the EZ220 series 300 mA minimum recommended B There is a desiccant pack attached to the housing base under the camera which is designed to absorb any moisture trapped inside the housing during adjustment To avoid excessive moisture build up it is recommended that the camera not be installed in rainy or excessively damp conditions It is also advisable to limit the number of times the housing cover is removed The desiccant pack can be replaced if condensation develops inside the housing Ill Parts Names lt EZ220B gt PCB Housing Assembly Screw Swivel Screw 4 Mounting Bracket O Ring Seal N Base Base Plate lt EZ220M gt Manual Lens Mount Ring a Cover SEverFocus la OO ON Screw IV Installation Instructions Connect the camera with the mounting bracket supplied Remove the bracket base from the mounting bracket Using the supplied sc
3. V Specifications Pickup device 1 3 interline transfer CCD Picture element 512 x 492 NTSC 512 x 582 PAL Horizontal resolution 340 TV Lines Sensitivity 2 0 lux F 1 2 S N ratio Over 48 dB Electronic shutter Up to 1 100 000 Gamma correction gt 0 45 Video output 1 0Vp p 75 ohm Power source 12VDC 10 300mA Sync Mode Internal Sync Lens mount M12 x PO 5 Board Lens Pinhole Lens C or CS Manual Lens Dimension 57 D x 110 L mm Operating temperature 0 C to 50 C IJ EverFocus Ill Parts Names lt EZ220B gt PCB Housing Assembly Screw Swivel Screw Fixing Screw v Board Lens Mounting Bracket MZ22G00100 O Ring Seal Mounting Base Base Plate lt EZ220M gt J E Manual Lens C Mount Ring Housing Cover IJEverFocus Fixing Screw IV Installation Instructions Connect the camera with the mounting bracket supplied Remove the bracket base from the mounting bracket Using the supplied screws mount the bracket base in the desired location Reassemble the bracket with the camera onto the mounting base EZ220 Series INSTRUCTION MANUAL 1 3 Color outdoor WaterProof Camera I General The EZ220 series of cameras contain a CCD camera in a stylish and attractive waterproof housing EZ220 series uses a high sensitive 1 3 color interline transfer CCD sensor with low lux performance it is available in two versions a Model EZ220B w
4. e camera is mounted outdoor a camera housing 1s required M12 x PO 5 Board Lens Pinhole Lens C or CS Manual Lens 57 D x 110 L mm e Do not disassemble it or place it on an unstable base e Do not touch the surface of CCD sensor by hand directly When O C to 50 C the camera is not in use put the cover cap on the lens mount e Never face the camera toward the sun e Use N D filter or set large F number of manual lens when the light intensity is very high in order to protect the sensitive CCD sensor e Use proper power source otherwise the camera will not function MZ22G00100 correctly
5. ith board lens available in f 3 6mm f 4 3mm f 6 0mm f 8 0mm format b Model EZ220M with CS mount can use any C and CS mount 1 3 format manual iris lens excluding varifocal lenses Auto iris lenses can not be used with the model ll Precautions e Do not expose the camera to humidity and dust If the camera is mounted outdoor a camera housing is required e Do not disassemble it or place it on an unstable base e Do not touch the surface of CCD sensor by hand directly When the camera is not in use put the cover cap on the lens mount e Never face the camera toward the sun e Use N D filter or set large F number of manual lens when the light intensity is very high in order to protect the sensitive CCD sensor e Use proper power source otherwise the camera will not function correctly Loosen the swivel screw and then point the camera in the desired direction Tighten the swivel screw Connect the BNC connector of the camera to a monitor or other video device through a 75 ohm type coaxial cable with BNC female connector at cable extension Connect the DC 12V regulated power source of the camera DC Jack to the DC12V power in jack with 2mm center outer plug Our factory settings is for you to get the best image within 3 5 Meters If it is out of focus you can also adjust the focus according the following procedures a Remove the three fixing screws which hold the housing cover b Carefully pull
6. rews mount the bracket base in the desired location Reassemble the bracket with the camera onto the mounting base V Specifications Pickup device 1 3 interline transfer CCD Loosen the swivel screw and then point the camera in the desired direction Tighten the swivel screw Connect the BNC connector of the camera to a monitor or other video device through a 75 ohm type coaxial cable with BNC female connector at cable extension Connect the DC 12V regulated power source of the camera DC Jack to the DC12V power in jack with 2mm center outer plug Our factory settings is for you to get the best image within 3 5 Meters If it is out of focus you can also adjust the focus according the following procedures a Remove the three fixing screws which hold the housing cover b Carefully pull the housing cover from the back plate Please pay attention to prevent damage to the O Ring seal c Loosen the lens mount fixing screw located at side of the lens by using the L wrench supplied d Adjust the lens to bring the subject into focus e Secure the lens mount fixing screw firmly again f Overlaying the cover gently in order to prevent damage to the O Ring and camera components Notes A Make wiring connections only after it has been determined that power has been disconnected Use only a 12VDC power supply for the EZ220 series 300 mA minimum recommended B There is a desiccant pack
Download Pdf Manuals
Related Search