MiniPro 2-Bay RAID System User Manual
Contents
1. MiniPro 2 Bay RAID System User Manual For more information visit our website at www oyendigital com 4 Installing Drives cont b Mount the HDD bracket to the drive using the included screws A a A z a er c Insert the HDDs into the MiniPro and reinstall the backplate 1 Specifications Application e 2 x 2 5 SATA Hard Drives up to 12 5mm height e eSATA e FireWire 800 USB 3 0 Super Speed Interface Ports e RAID 0 Striping RAID Modes e RAID 1 Mirroring Windows XP 7 8 or higher e Mac OS 10 4 or higher System Requirements e Temperature 5 C 40 C e Humidity 10 RH 80 RH Temperature 20 C 70 C e Humidity 5 RH 90 RH Input AC 100 240V 50 60Hz or bus power Output DC 12V 2A 5 2 x 3 5 x 2 2 inches Operating Environment Storage Environment Enclosure Size 5 System Set Up If you are installing new drives you must format the volume before it is accessible 1 Connect the MiniPro to the computer Power the MiniPro from the AC adapter or FireWire bus power 2 The system is defaulted for RAID 1 Mirroring for data redundancy To change the mode to RAID 0 Striping HDD A amp HDD B merged configure the mode by navigating through the LCD menu as shown in section 7 3 After the RAID is configured use Disk Management on the PC or Disk Utility on the Mac to format the volume Windows http oyendigital com FAQs html 10 Mac http oyendigital c2. with an HDD it will display No Communication The LEDs for the HDDs will be GREEN if the drive status is healthy Simply check the connection to the computer 10 Warranty Information This product includes a two 2 year repair replacement warranty provided by Oyen Digital This warranty is non transferable and is limited to the original purchaser Warranty service may be requested by completing the form at the following link www oyendigital com rma request form html
3. Alarm Setup Backlight Setup Version RAID1 Enter gt Select OFF Enter gt Select ON Enter gt OK OK Vv v HDD1 Change RAID Mode Set Mute Alarm Set Backlight Serial Number jtoRAIDO Set gt ON Set gt OFF Set gt OK OK Yy Y HDD1 Are you sure Temperature Ok gt OK OK Vv Vv HDD2 Erase all data Exit Settings Serial Number Ok gt OK gt OK Vv HDD2 Note The unit must be connected Temperature to a computer when configuring 3 Installing Drives To install or exchange drives do the following a Remove the screws located at the backplate of the case and slide out the HDD brackets from the enclosure If one of the HDDs fails the HDD LED will blink RED A new HDD can be installed and it will automatically rebuild with data if configured for RAID 1 mode Note The use of identical HDDs from the same manufacturer with the same capacity and RPM is recommended 1 Power down the MiniPro RAID 2 Remove the failed HDD 3 Install the new HDD and power up the MiniPro 4 The orange rebuild LED will illuminate and the LCD will indicate a rebuild in progress The rebuild process can take several hours 9 Troubleshooting If the system experiences an HDD failure The LED for the HDD will blink red and the LCD will display the following message RAID Warning Degraded Array If the system experiences a communication failure When the MiniPro is not connected to a computer or not able to communicate
4. om FAQs html 8 If you are installing existing drives that already have data please note that HDD A will be the master The data from HDD A will be automaticallly copied to HDD B and overwrite any existing data on HDD B 6 Power The MiniPro RAID can be powered using the included AC adapter or the FireWire connection To power the unit from FireWire bus power but use USB 3 0 or eSATA for data Connect the MiniPro to your computer using the USB or eSATA cable Connect the FireWire cable from the MiniPro to the computer The MiniPro will then use the FireWire connection for power but the USB 3 0 or eSATA connection for data 2 Detailed View LED indicators A Green Solid normal Blinking read write activity Red Blinking Drive Error n 66 Orange Rebuilding data The LCD menu provides the ability to view system information and configure the RAID mode alarm sounder and backlight Press Select to enter the menu RAID Mode Default RAID 1 This setting configures the RAID mode Alarm Setup Default Off Enables a sounder to annunciate when an HDD error exists or the unit is not connected to a computer Backlight Setup Default On Enables disables the LCD backlight System Settings Select Select menu or mode TCM Select Enter gt OK Confirm or Enter OK OK Y Y Firmware RAID Mode Setup
Download Pdf Manuals
Related Search