SB-2000 User Manual 2011
Contents
1. 42 10 Daily Maintenance Cleaning 50 11 Product Specifications 55 SB 2000 Operator s Manual V 3 1 2 1 Introduction 1 1 Introduction This guide covers the installation maintenance and troubleshooting of SB 2000 Series Currency Discriminating Counter We recommend reading this guide thoroughly before operating the Currency Discriminator Then as you become more familiar with SB 2000 use it as a reference guide to look up information when you need tt 1 2 FCC Compliance THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can emit radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference in radio communications Operation of this equipment in a residence area is likely t2. GRAND TOTAL REPORT Time 04 01 2010 15 41 Currency USD STATION 1 Deposit No 1 LELIIQSLIISLDLIISLIISLIIIBPSLIISPSLILILLIISLIISRSLIISLIJ DENIM PC3 TOTAL 1 2039 2039 2410 260 1750 1700 Ce ek aa sia ai B sa aaa aa AA AA aaa da aaa TOTAL 2345 8159 iq N 87 A l 87 I Ri W AYA A q A ee a A rl Is SB 2000 Operators Manual V 3 1 37 7 3 RJ DETAIL PRINT This report will show detail reasons of all rejected banknotes After selecting 3 RJ DETAIL PRINT press CE ENTER key to print User can print a detail report of rejected notes using this function PRINT MENU 1 TOTAL PRINT 2 GRAND TOTAL PRINT i F DE TAIL PR DIMENSION ERROR CHAIN HALF NOTE CF A ERROR CF B ERROR CF C ERROR CF D ERROR CF E ERROR CF F ERROR CF G ERROR CF H ERROR DOUBLE ERROR MISMA ICH1 IMAGE ERROR MISMA T CH2 BAICH FULL HEJECI FULL NOIE ERROR BEKRERERERERERERERERER ER ERE kek kok kek k ERE RERERERER ERE Reject Total 0 dokn ee eene REE ER ERER ERE RERERERERERERER SB 2000 Operators Manual V 3 1 38 7 4 FUNCTION VALUE PRINT This report will show value of all sensors and useful for service technician Aft
3. SB 2000 Series CURRENCY DISCRIMINATOR OPERATOR S MANUAL Revised 06 01 2011 AMROTEC USA Issued date Country Documentversion Ver3 1 Table of Contents 1 Introduction 3 1 1 Introduction 3 1 2 FCC Compliance 3 2 Important Safety Information 4 2 1 Safety Precaution 4 2 2 Installation and Handling of the Machine 6 3 Description of Parts and Control Panel 8 3 1 Parts Description 8 3 2 Overview of LCD Display Screen 9 3 3 Overview of Control Panel 10 4 Getting Started 13 4 1 Setting Up 13 4 2 Initialization 13 4 3 Placing Bills into the Hopper 14 4 4 Connecting of External Devices 15 5 Basic Operation and Modes 16 5 1 Selecting Operation Modes 17 5 2 Selecting Batch Function 22 5 3 Selecting Add Function 23 5 4 Changing Display Contents 24 6 Set Function and Parameters 25 6 1 Main Function Menu 25 6 2 Engineering Setup 35 7 How to Print Reports 36 8 How to Clear Counting Results 40 9 Troubleshooting
4. ORT F ALL O ALL 5 FACE and F ALL Facing means to arrange banknotes by its face In this mode the machine reads the first note to determine the face and denomination information Then it transports the banknotes whose face and denomination are the same as the first banknote to the output stacker and all mismatch banknotes to the Reject Pocket If user wishes to start counting a particular face and denomination first then empty the output Stacker and the input Hopper and retry with the first note having preferred face and denomination This Face mode also equipped with a F ALL Face All sub mode where machine allows you to sort mixed banknotes by their face The machine reads the first note to find out the face information despite of denomination SB 2000 Operators Manual V 3 1 20 ORT and O ALL mode Orientation In this mode the machine arranges the banknote with its direction face and denomination The machine reads the first note and determines the denomination direction and face Then it sorts the banknotes with the information If a note has same denomination face and direction then it transports the banknote to the output Stacker Otherwise it sends to the Reject Pocket This Orientation mode also equipped with an O ALL sub mode where machine allows you to sort mixture of banknotes by its orientation The machine reads the first note to find out the direction of face information despite of the deno
5. SB 2000 Operator s Manual V 3 1 7 3 Description of Parts and Control Panel 3 1 Parts Description NOTE GUIDE HOPPER CONTROL PANEL e o TEE NN DISPLAY REJECT POCKET STACKER POCKET TOP COVER HANDLE POWER INLET EXTERNAL PORTS lt REAR VIEW gt SB 2000 Operators Manual V 3 1 8 3 2 Overview of LCD Display screen LCD Display The message description and placements are defined below When a guide message shows up the screen automatically changes to normal display from detail display Batch Size Batch by Value Counting Mode Stacker oe Total stacker TOTAL Total Reject Motes Reject ADD On Ofl4 CF Detection On Off Error Messages Main display screen SB 2000 Operators Manual V 3 1 9 3 3 Overview of Control Panel 3 3 1 Mode key Iu User can choose from MIX SDC DIR SNP Option and CNT mode SDC SORT SNP CNT When MODE key is pressed continuously the mode changes to the next one gt MIX Mixture of denomination banknotes SDC Single denomination of banknotes SORT Separating denomination from an organized strap DIR Direction by facing orientation and denomination SNP Serial Number printing function Optional feature 4 4 4 4 Count Non Discriminating Piece count 3 3 2 DENOM key gt User can select desire denomination in SDC and in DIR mode DENOM key is als
6. To turn ON or OFF this function first enter into the 15 MACHINE VALUE PRT menu using A and select ON OFF using P gt lt 4 key Once selection is made Press EXIT key to confirm the setting and EXIT key again to escape from this menu and return to main screen 16 TIME SETTING All SB 2000 machines usually ship from factory with time set for North America Eastern Time Zone However if it is not set correctly or due to day light savings user can reset the year months date and time of the SB 2000 TIME SETTING YEAR XX MONTH XX DATE XX HOUR XX MINUTES XX VA 4 SB 2000 Operator s Manual V 3 1 32 To reset date and time for SB 2000 first enter into the 16 TIME SETTING menu using A V and set your date and time using gt lt key Once selection is made Press EXIT key to confirm the setting and EXIT key again to escape from this menu and return to main screen 17 SB TOTAL COUNT Trained users and service technician are able to retrieve and view lifetime count of the machine using this function This count report does not include count of reject banknotes Even when SB 2000 is turned off machine does not erase the machine count and automatically save into the memory MACHINE TOTAL CNT XFFFF 1ST XXXXX XFFFF 2ND 0 VA To retrieve lifetime count for the SB 2000 first enter into the 17 MACHINE TOTAL CNT menu using A Y and LCD display screen will
7. capacity of the Reject Pocket can be change using this sub menu If users normally process good quality notes then the capacity of the Reject Pocket should be set maximum 70 notes otherwise the value should be set to minimum 50 notes for the Reject Pocket To set to a value first enter into the 3 REJECT NUMBER sub menu using A V and move to a level using P gt 41 key Once selection is made Press EXIT key to confirm the setting and EXIT key again to escape from this menu and return to main screen REJECT CAPACITY 50 60 70 80 4 4 LCD CONTRAST This menu decides the contrast of the LCD display screen To change the LCD contrast first select 4 LCD CONTRAST menu using V and move to a level High Medium and Low using lt key Factory default setting is close to High Once selection is made Press EXIT key to confirm the setting and EXIT key again to escape from this menu and return to main screen SB 2000 Operator s Manual V 3 1 27 LCD CONT LEVEL 5 BAUD RATE User can Set up baud rate for communication as below Factory default is 115Kpbs 9 6Kbps gt 38 4Kbps gt 115Kbps BAUD RATE 9 6K gt 38 4K gt 115K To change communication baud rate first enter into the 5 BAUD RATE menu using Y and select the proper baud rate using key Once selection is made Press EXIT key to confirm the setting and EXIT key again to escape from this menu and retu
8. holes under the side cover Close the Back cover as shown below S S Push the door until it clicks ie 1 L x es T n YA p 54 SB 2000 Operators Manual V 3 1 11 Product Specification Item Specification Size W x D x H 321mm W x 355mm D x 334mm H inch 12 72 IW x 14 D x 13 H Kg lbs Approx 14 kgs 31 Ibs Notes Max 500 Notes Max 200 Reject pocket capacity Notes Max Display Type Dot 128 x 64 Graphic LCD RS232C Port USB Port s w upgrade Weight Hopper capacity Stacker capacity CO Connectivity interfaces Currencies available 1 Available up to 3 currencies 50 100 100 190mm Banknote size range Banknote thickness 0 08 0 12 range Counting Speed Notes min About 720 NPM approx MIX SDC SORT DIR SNP optional CNT DIR FACE ORT F ALL O ALL 1 200 MG and UV Optional IR MR FL CIS etc 90 240VAC 50 60Hz Standby 25 Operation 105 Discrimination Mode Preset Batch Number Counterfeit Detection Power Requirements mm Power Consumption Operational 0 50deg 30 85 RH Non Condensing requirements Notes SB 2000 machine product specification can be changed without further notice The contents of this operator s manual can also be changed without notice Printed in Korea June 1 2011 Copyright 2011 AMROTEC USA SB 2000 Operator s Manual V 3 1 55
9. print output STATION ID SET ID NUMBER 1 VA lt gt To select Station ID first enter into the 20 STATION ID SET menu using Y and select 1 255 using lt 44 key Once selection is made Press EXIT key to confirm the setting and escape or EXIT key again to escape from this menu and return to main screen SB 2000 Operators Manual V 3 1 34 6 2 Engineer setup Password Protected area This menu is strictly restricted for users Only authorized service professional of SB 2000 are able to enter into this menu to make adjustment of counterfeit detection settings and machine initialization set up Please contact your master distributor for the password to enter into this menu and instructions for item 6 2 1 and 6 2 2 and 6 2 3 622 IR SENSOR SET If equipped 925 MACHINE INITIALIZE SB 2000 Operator s Manual V 3 1 35 7 How to Print Reports SB 2000 be connected to several serial dot matrix printers such as Samsung SRP 275A Citizen IDP 3550 etc If Printer is purchased with SB 2000 and connected to the machine users can print several types of counting reports as described below To Print a particular report press key to access to the main print menu and make your selection by using A V key Once selection is completed press ce key to print that particular report you selected 115 7 1 TOTAL PRINT PRINT MENU 2 GRAND TOTAL PRINT 3 RJ DETAIL PRINT 4 FUN
10. second screen where user can erase the Grand Total saved into the memory Choose YES to erase and NO to escape followed by CE ENTER key To return to Main Menu press EXIT key twice CLEAR MENU 1 GRAND TOTAL CLEAR 1 GRAND TOTAL CLEAR 3 ADD TOTAL CLEAR YES NO WA SEL ENTER OK VA ITEM ENTER OK SB 2000 Operators Manual V 3 1 40 8 2 TOTAL CLEAR CURRENT RESULT B To clear current counting results enter into 2 TOTAL CLEAR menu and press CE ENTER to reach to a second screen where user can erase the current counting results Choose YES to erase and NO to escape followed by CE ENTER key To return to Main Menu press EXIT key twice CLEAR MENU 2 TOTAL CLEAR 1 GRAND TOTAL CLEAR 2 TOTAL CLEAR ADD IO AF YES NO VA ITEM ENTER WA SEL ENTER Note that users can clear current counting result by pressing CE ENTER key without going through the CLEAR menu 8 3 ADD TOTAL CLEAR B This menu is used to erase the immediate last counting result from the grand total saved in the memory only apply to when ADD function is being activated CLEAR MENU 1 GRAND TOTAL CLEAR 3 ADD TOTAL CLEAR 2 TOTAL CLEAR 3 ADD TOTAL CLEAR YES NO WA SEL ENTER OK VA ITEM ENTER OK To clear current counting results during an accumulation ADD count enter into ADD TOTAL CLEAR menu and press CE ENTER to reach to a second screen where user can erase
11. 115K If the machine has optional SNP mode default printer type is set to Parallel Port Interface 1 CF SENSOR SET User or authorized personal can turn ON or OFF the Counterfeit detection feature installed with your SB 2000 from this menu item As a standard feature SB 2000 is equipped with Ultra Violet and Magnetic Detection sensors which are embedded within a single CF feature Advanced SB 2000 model can also be equipped with other means of counterfeit detection feature as optional feature CF SENSOR SET ON OFF Once user enters into the main menu select 1 CF SENSOR SET using V A key Use lt gt to select ON OFF Once selection is made press EXIT key to confirm the setting and EXIT key again to escape from the main menu SB 2000 Operator s Manual V 3 1 26 2 DOUBLE LEVEL Double level is used to set double detection for banknotes If SB 2000 stops for doubles frequently user can lower the value to prevent double errors Please change the value with small increment cautiously Do not attempt to perform this adjustment without consulting with your sales representative or an SB 2000 authorized service technician DOUBLE VALUE VALUE 45 VA 4 Once user enters into the main FUNC menu select 2 DOUBLE LEVEL Use 4 key to change the value Press EXIT key to confirm the value and EXIT key again to escape from this menu and return to main screen 3 REJECT NUMBER The
12. 17 CF H ERROR CF D ERROR CF E ERROR To show possibility of counterfeit on IR Sensor IRA To show possibility of counterfeit on IR Sensor IRS To show possibility of counterfeit on IR Sensor IRH To show possibility of counterfeit on IR Sensor water mark detection Adjustment of image sensor setup after check image IRA setting check Adjustment of transmit image sensor setup after check image IRS setting check Adjustment of transmit image sensor setup after check image IRH setting check Adjustment of transmit image sensor setup after check image SB 2000 Operator s Manual V 3 1 46 9 3 Error Codes for recognition error on the Display Screen No Erorcode cause soon MISMATCH MISMATCH The banknote is different denomination from the first recorded banknote SDC mode The banknote is different orientation from the first recorded banknote DIR ORT mode Check the rejected banknote or information code Resume counting by pressing START STOP key BATCH FULL REJECT FULL A BATCH ERROR IMAGE ERROR Current counting number PCS reached the pre set batch number on the stacker Reject pocket reached the maximum banknotes In case of user picking up banknote from stacker during counting Banknote is not recognized by the image sensor SB 2000 Operators Manual V 3 1 Remove notes from stacker pocket Resum
13. C VALUE PRINT Y A ITEM ENTER OK This report will show current count Report shows current total of counted banknotes by quantity and amount After selecting 1 TOTAL PRINT press CE ENTER key to print If AUTO PRINT function is activated ON from the menu See 10 AUTO PRINT page 30 SB 2000 prints current total as soon as a counting is completed and bills are removed from the Stacker iF ir Ik k TE ir ir ko kk i r RE PO RT i ir krik Time 04 01 2010 15 49 Currency USD STATION 1 Deposit Mo 2 w NEN W Wi 87 PARSE AW W W AAAS PAA Wi i AAS A AA DENIM PCS TOTAL eee ir kr eee eee eee esa ir kok qi Settee g g 3 15 19 190 13 260 1 at W Tl AEP i AATE PASSE Al l Wr IN AEP I Al iii Wi IN AAA AA TOTAL 45 524 ir ir kok Tk He ir Iko ik ir kk qi Sr SB 2000 Operators Manual V 3 1 36 7 2 GRAND TOTAL PRINT This report will show current count Report shows grand total of counted banknotes by quantity and amount After selecting 2 GRAND TOTAL PRINT press CE ENTER key to print PRINT MENU 1 TOTAL PRINT 2 GRAND TOTAL PRINT 3 RJ L i 4 FUNC VALUE PRINT Y ITEM ENTER OK E E SS Sse Se Ee ee ee eee ee El Em ue
14. Manual V 3 1 29 10 AUTO PRINT If this AUTO PRINT function is activated ON SB 2000 prints current total as soon as counting is completed and bills are removed from the Stacker User can also set the SB 2000 to print optional serial number of banknotes automatically once counting is completed AUTO SERIAL PRINT ON OFF To set automatic serial number printing ON OFF first enter into the 10 AUTO PRINT menu using Y and select ON OFF using 4 key Once selection is made Press EXIT key to confirm the setting and EXIT key again to escape from this menu and return to main screen 11 KEY BEEP SETTING lf Key Beep function is set to ON an audible beep tone will generate when a key is pressed otherwise it will not be sound off To turn Beep ON or OFF first enter into the 11 KEY BEEP SETTING sub menu using V and select ON OFF using Once selection is made Press EXIT key to confirm the setting and EXIT key again to escape from this menu and return to main screen SB 2000 Operator s Manual V 3 1 30 12 AUTO START In Automatic mode user can automatically starts the machine counting when machine detects a note on the hopper Whereas in Manual mode the machine only starts counting when a banknote is placed on the hopper and START STOP key is pressed by user AUTO START ON OFF 4 To turn Auto Start ON or OFF first enter into the 12 AUTO STAR
15. T menu using V and select ON OFF using gt lt 4 key Once selection is made Press EXIT key to confirm the setting and EXIT key again to escape from this menu and return to main screen 13 EXTERNAL DISPLAY If External Customer Display was purchased along with SB 2000 user can connect the Customer Display at the rear of the machine External Customer display shows the current counting results including quantity and value of banknotes EXTERNAL DISPLAY ON OFF To engage or disengage External Customer Display first enter into the 13 EXTERNAL DISPLAY menu using V and select ON OFF using 4 key Once selection is made Press EXIT key to confirm the setting and EXIT key again to escape from this menu and return to main screen SB 2000 Operator s Manual V 3 1 31 14 REJECT DETAIL PRINT User can print a detail report of rejected notes using this function If this function is turned ON SB 2000 prints the detail report of the rejects banknotes automatically once counting is completed if an external printer is connected RJ DETAIL PRINT ON OFF 15 MACHINE VALUE PRINT for service technician only Trained users or authorized service technician of SB 2000 is able to print out information of factory set parameters and value When this function is ON SB 2000 prints this machine information automatically if an external printer is connected MACHINE VALUE PRT ON OFF
16. ade software or transfer machine data parameter or control the machine vice versa gt Connect an interface cable to D and 2 Printer Interface Connection SB 2000 can print out counting results and machine parameters to an external printer Optional if connected gt Connect an interface cable to 3 Customer display Connection SB 2000 can display the result through a Customer Display unit optional gt Please connect your customer display to 3 SB 2000 Operator s Manual V 3 1 15 5 Basic Operation and Modes Mode o Display Screen Specification Count mixture denomination of selected currency banknotes Value batch es BVAL ee e Count the selected denomination BAA NA CA AA SDC Selected of banknote and reject mismatch denomination banknotes to reject pocket UP DOWN FACE FACE MIX FACE F All F ALL Organizing single denomination or mixture banknotes by its face DIRECTION direction and orientation MIX ORT O ALL O ALL Separation of organized Strap of SORT SORT banknotes oot _ ss serial number of banknotes Counting Mode is for counting all currencies without detection GT Grand total SB 2000 Operators Manual V 3 1 16 5 1 Selecting Operation Modes There are four main counting modes COUNT MIX SDC and SORT modes Furthermore the machine provides the facilities to align notes with same face up and down face or same directions Orientation For detail pleas
17. al save function any longer How to set Batch Value Dollar amount lt Move between digits Y Increase values decrease values CE ENTER Enter into setting values mode ADD Clear setting values EXIT Save setting values After setting of the batch value press EXIT key to exit SDC mode Single Denomination Count In SDC mode user can count single denomination of banknotes while separating other denomination of banknotes mixed within a strap When SB 2000 reads a note whose denomination is the same as the first denomination of note counted or same as pre set denomination then it reads the banknote and sends the banknote to output stacker If the banknote is not the same denomination the machine then sends the banknote to Reject Pocket SB 2000 Operators Manual V 3 1 18 To change counting mode to SDC mode press MODE key until SDC is displayed on LCD display screen as shown below After changing the counting mode to SDC mode user could select a denomination by pressing DENOM key or stay with DD detected denomination If a denomination is selected the selected denomination will be displayed on the LCD screen as shown below For example US dollar every time DENOM key is pressed the denomination will be changed sequentially DDt 11 52 S 5t 104 9204 50 9100 DD is an abbreviation of Detected Denomination If DD is selected SB 2000 detects the denominated first banknote as standar
18. ation break down by Value and Total Amount SB 2000 Operators Manual V 3 1 24 6 Set Function and Parameters 6 1Main Function Menu Please note that function and its parameters setting are password protected to prevent unauthorized access Contact your distributor for password to unlock this function menu Once it is unlocked user can enter into the main menu and its parameters Once FUNC FUNC key is pressed followed by password main menu setup screen is displayed as below Use a Key to select a parameter and press Key to confirm the selection Press EXIT key to browse around or press EXIT key twice to escape from the main menu The below screens display the selected parameter s setup screen 1 CF SENSOR SET 2 DOUBLE LEVEL 3 REJECT CAPACITY 4 LCD CONTRAST 5 BALD RATE 6 MOTOR TEST 7 SENSOR CHECK W CHANGE CIE OK 8 SPEED 9 SPOOL SETTING 10 AUTO PRINT 11 KEY BEEP SETTING 12 AUTO START 13 EXTERNAL DISPLAY 14 REJECT DETAIL PRT A CHANGE OK 15 MACHINE VALUE PRT 16 TIME SETTING 17 SB TOTAL COUNT 18 MODE LOCK SETTING 19 VERSION INFO 20 STATION ID SET CIE OK SB 2000 Operators Manual V 3 1 25 The factory default settings are described on the table below Function Parameter Default Value Speed About 720 NPM LCD Contrast High Key Beep Off Auto Start On Pocket Capacity Reject 50 notes Printer Serial Baud
19. d SB 2000 then counts the banknotes of that denomination to output stacker and sends all other denominations banknotes to reject pocket If the output stacker and the input Hopper are emptied the machine will try to find a new denomination of the first note in next trial and sorts the banknotes with the new denomination SORT MODE counting of organized strap In SORT mode SB 2000 allows you to count and sort stack of organized mixed denomination banknotes into straps and verify deposits Each time machine begins processing of a new stack of banknotes it automatically starts counting of the first note fed from the hopper When a note of a different denomination from the first denomination is detected machine stops and keep the new denomination banknotes within the transport path User would then be asked to remove all notes from the stacker CLEAR STACKER and once that is done machine resumes counting Machine will send the new denomination of banknote to the stacker and continue the operation in this matter This should be noted that during this SORT operation there will be some banknotes rejected every time a new denomination is detected and machine stops These rejects notes are not added to the total count and must be SB 2000 Operators Manual V 3 1 19 counted manually by users SORT gt T 0 PCS DIR MODE Facing and Orientation of banknotes DIR mode is divided into four separate sub modes as below DIR Mode
20. e counting by pressing START STOP key Remove reject banknotes from the Reject Pocket Resume counting by pressing START STOP key Resume counting by pressing START STOP key Check the banknote manually for genuine or suspect If genuine place the banknote on the input hopper and resume counting If banknote is genuine but image sensor is failed to recognize then contact your service professional DIMENSION ERROR HALF NOTE SB 2000 Operator s Manual Banknote is larger in size compare to genuine banknotes Banknote is equal to half of the size of genuine banknotes V 3 1 48 Check the banknote manually for genuine or suspect If genuine place the banknote on the input hopper and resume counting If banknote is genuine but image sensor is failed to recognize then contact your service professional Remove the banknote from the stacker and discard If genuine banknote in original size found to show this error then contact your service professional 10 Daily Maintenance Cleaning 10 1 Cleaning of the sensor at the Hopper Clean the hopper sensor with an air dust cleaner or a cotton or silk cloth as shown on the below picture 10 2 Cleaning of the roller at the hopper Clean the feeding roller with a cotton or silk cloth as shown on the picture below l H ax Fa ar arr ur L PI 40 n S lil H ay LA 1 75 i I l li i
21. e refer to the DIR mode described below The modes are changed in sequence every time when the MODE key is pressed as shown below SDC SORT SNP option CNT MIX mode Mixture of denominations In Mix mode the SB 2000 machine counts and discriminates mixture denominations of banknotes such as mixture of 1 5 10 20 etc If the denomination of a banknote is successfully discriminated then the banknote will be sent to the output stacker If a note fails to be detected or it is a counterfeit suspect if CF mode is ON the banknote will be sent to the reject pocket To change into the MIX mode press MODE key until MIX is displayed on LCD SB 2000 Operator s Manual V 3 1 17 MIX mode BVAL In Mix mode BVAL user can set a Dollar amount Value and batch mixture denomination of banknotes by amount For example user can set the Batch Value as 300 and count mixture denomination of banknotes SB 2000 will stop when total stacker amount reaches the Batch Value VALUE BATCH MENU VALUE x 4 MOVE DIGIT V INC DEC VALUE ENTER SAVE EXT EXIT B BVAL mode can be activated by pressing DENOM key DENOM t 200 BVAL B BVAL amount can be set by pressing BATCH key until BVAL is flashing followed by CE ENTER key to enter into setting menu as shown above If BVAL mode is activated Grand Total clears automatically and user cannot use Grand Tot
22. er selecting 4 SB 2000 VALUE PRINT press CE ENTER key to print PRINT MENU 1 TOTAL PRINT 2 GRAND TOTAL PRINT 3 RJ ceta Y ITEM ENTER OK 1 UV TOP SENSOR SET UVT ON OFF ON UVT FL 130 UVT RL 100 UVT TFL 15 2 UV BOT SENSOR SET IR ON OFF ON IRA 50 IRS 12 IRH 12 3 MG SENSOR SET MG ON OFF ON MG LEFT 10 MG CENTER 50 MG RIGHT 10 4 DOUBLE LEVEL DOUBLE Value 45 5 REJECT CAPACITY REJECT Number 50 6 LCD CONTRAST LCD Contrast 26 7 BAUD RATE BAUDRATE 115200bps 11 SPEED SETTING SPEED SETTING 960 12 SPOOL SETTING SPOOL SETTING 2 Level 13 SERIAL PRINT SN Print ON OFF OFF 14 BUZZER Buzzer ON OFF OFF 15 AUTO START Auto Start ON OFF ON 16 EXTERNAL DISPLAY EX Display ON OFF OFF SB 2000 Operators Manual V 3 1 39 8 How to Clear Counting Results User can clear current counting result by simply pressing CE ENTER key Trained users can also erase current counting results grand total count etc from CLEAR MENU Press CLEAR key to enter into the CLEAR MENU and the below window screen appears on the LCD display CLEAR MENU 1 GRAND TOTAL CLEAR 2 TOTAL CLEAR 3 ADD TOTAL CLEAR VA ITEM ENTER Select your desire report by using A Y direction keys and CE ENTER to confirm the selection 8 1 GRAND TOTAL CLEAR To clear Grand Total saved in the memory enter into 1 GRAND TOTAL CLEAR menu and press CE ENTER to reach to a
23. esired batch number for each denomination using four direction keys V gt 1 2 5 10 20 50 100 v A DENOM P gt A V Select Denomination lt gt Set Batch number press 1 time to change with 1 increment Keep on pressing or hold down to change the number rapidly After denomination batch setting is completed and confirmed press EXIT key to escape 5 3 Selecting Add Function m ADD Function in all modes CTN MIX SDC FACE and ORT mode When ADD function is activated SB 2000 accumulates multiple deposits and also keeps running total in between all the modes and save them to memory Each of these running totals will be added automatically and carry over to the next count when modes are changed For example a running total in MIX mode can be carried over to the running total in SORT mode Total amount will be displayed all the time even when multiple counts are performed 5 4 Changing Display Contents The machine provides various information regarding counting results Every time a count is completed user can enter into different display screen by pressing direction key as illustrated below SB 2000 Operator s Manual V 3 1 23 lt Current Count Screen gt lt Denomination break down by qty si 2 5 510 s 20 s 53100 TOTAL PCS gt 2 55 510 5 20 50 5100 AMOUNT 5 Return to Current Screen Denomin
24. etween different menu items SB 2000 Operator s Manual V 3 1 11 3 3 10 Left Right key gt 5 These left right direction keys are used to set up batch function 1 200 and increase or decrease batch number by 1 increment Right direction key P is used to change into different screen during discriminating modes MIX SDC and SORT etc BATCH 3 3 11 Batch key S BATCH key is used to perform regular batch 1 200 count in piece count CNT mode BATCH key is also used to activate denomination batch function DB In MIX mode using of BATCH key function user can enter into BVAL mode where user can count a batch by pre selected amount 3 3 12 CE ENTER key CE ENTER key is used to choose and select all setting options under Main menu batch setting etc EXIT Key is used to confirm all setting changes CE key is also used to clear current counting result on the screen CE is an abbreviation of Clear 4 Enter 3 3 13 GT Grand Total key GT provides user with Grand total count on the screen 3 3 13 EXIT key EXIT EXIT key is used to confirm all setting changes and exit at the same time B EXIT key allows user to escape from a set up screen or back to main menu screen if pressed twice SB 2000 Operators Manual V 3 1 12 4 Getting Started 4 1 Setting up POWER INLET SWITCH Power Cord Plug one end of the cord into the back of the machine and the
25. l I i i I i Im 3 i du Md ut lad d a 1 II il l a x5 Fi 3 ut a ra AG ini 171 i OIN A Tod S 1 l TEX i XS zA Mr ET gm QE LL Lm SB 2000 Operators Manual V 3 1 49 10 3 Cleaning of the sensor at the stacker Clean the stacker sensor with a cotton or silk cloth or spray with an Air dust cleaner p 1 t 10 4 Cleaning of the sensor at the reject stacker Clean spray the reject pocket sensor with an Air dust cleaner when dust accumulates and sensor becomes less sensitive SB 2000 Operator s Manual V 3 1 50 10 5 Cleaning of detection sensor and roller inside B Pull the lever handle to open the Top cover d Clean the sensors and rollers as shown in the photo below with a cotton or silk cloth lt SE s x V Mm EN ES LS Won Ruta tm nl a E gt Eu AVR B Open the guide by pulling a part on the edge Clean the sensor as shown in the photo below with a cotton or silk cloth SB 2000 Operators Manual V 3 1 51 Pull up Close Top cover to push in SB 2000 Operators Manual V 3 1 52 10 6 Cleaning of the sensor inside Back cover B Pull the handle out to open the Back cover as below SB 2000 Operators Manual V 3 1 53 Using vacuum cleaner remove the dust from
26. mination CNT MODE Piece Counting mode In counting mode the machine only counts banknotes by pieces without discriminating a denomination To change into piece counting mode press MODE key until CNT is displayed on LCD display screen User can also accumulate multiple straps while in Count Mode OPTIONAL FUNCTION SNP MODE Serial number printing mode In SNP mode SB 2000 reads serial number of banknotes and print them as image on a factory configured thermal printer To change to the SNP mode press MODE key until SNP is displayed on LCD screen GT Grand total Display screen shows detail of current count results and Grant Total GT by quantity and amount for each denomination of banknotes SB 2000 Operators Manual V 3 1 21 5 2 Selecting Batch Function 5 Batching 1 200 and Preset Batch 200 100 50 20 10 SB 2000 is equipped with a BATCH key to allow users to strap single or mixture denomination of banknotes Batch is defaulted as 200 B200 as it affects the maximum stacker capacity To change default batch number 200 to variable batch between 1 200 or pre set batch value please follow the steps below In Count CNT mode continue to press BATCH KEY until it reached to your desire batch value BATCH B200 100 50 B20 B10 In all other modes to change the batch number value first press BATCH key and when B200 is blinking press ENTER key You can then continue t
27. n Please replace defective sensor after check condition of Count sensor C Count Sensor D clean Please replace defective sensor after check condition of Count Sensor D Stacker Sensor clean Please replace defective sensor after SB 2000 Operator s Manual V 3 1 44 it S Sensor breakdown check condition of Stacker Sensor Reject Sensor s Reject Sensor clean REJECT ERROR jamming Il Please defective sensor after check Sensor breakdown breakdown condition of Reject sensor SB 2000 Operators Manual V 3 1 45 9 2 Error caused by Banknote Recognition Module We sowon _ CF A ERROR CF B ERROR CF C ERROR To show possibility of counterfeit on UV FL sensor To show possibility of counterfeit on UV RL sensor To show possibility of counterfeit on MG Center sensor To show possibility of counterfeit on MG Left Right Sensor UV sensor clean Check UV Top sensor FL setting Replace defective sensor after check condition of UV sensor UV sensor clean Check UV Top sensor RL setting Replace defective sensor after check condition of UV sensor Brush roller ass y clean Check MG Center setting Replace defective sensor after check condition of MG Center sensor Brush roller ass y clean Check MG Left Right setting Replace defective sensor after check condition of MG Left Right sensor CF F ERROR CF G ERROR
28. o used to access to factory s default batch in MIX mode CUR 3 3 3 Currency key gt User can select the type of currency if multiple currencies are loaded from the factory gt When CUR key is pressed the currency changes to the next one For example USD EURO LOCAL if multiple currencies are loaded to the SB 2000 START 3 3 4 Start stop key STOP gt In counting CNT mode machine stops or resume counting from an error condition gt In SORT mode machine resumes counting from an stop condition Change of Denomination SB 2000 Operators Manual V 3 1 10 FUNC 3 3 5 Function key FUNC key is used to enter into Main Menu function and it is protected by password to prevent unauthorized access to Main Menu settings 3 3 6 Clear key CLEAR key is used to enter into CLEAR menu to clear current count grand total and memory 3 3 7 Print key atm PRINT key is used to enter into PRINT MENU function and user is able to print out different reports to an external Printer If printer is connected 3 3 8 Add key B ADD Key control the accumulation in piece count mode CNT and also used to accumulate and carry over total in between different modes such as MIX SORT etc 3 3 9 Up Down key a j vJ These Up down direction keys are used to set up batch function 1 200 and increase or decrease batch number by 10 increment Up down Direction keys are also used to browse in b
29. o cause harmful interference in which case the users will be required to correct the interference at their own expense SB 2000 Operator s Manual V 3 1 3 2 Important Safety Information 2 1 Safety Precaution Please read the safety precautions below before operating SB 2000 They must be observed to avoid any potential hazards that could result in personal injuries or damage to SB 2000 Currency Discriminator Counter ELECTRICAL SAFETY To avoid the risk of electrical shock fire or damage to SB 2000 Currency Counter 1 Do not remove machine covers or guards that require a tool for removal There are no operator serviceable areas inside your machine Contact your service personal for help 2 Never defeats interlock switches This machine is designed to restrict operator access to unsafe areas Covers guards and interlock switches are provided to ensure that the machine will not operate with covers opened Do disassemble SB 2000 yourself Do not use damaged or worn power cords or plugs 5 Keep metal objects such as paper clips away from the hopper and stacker If an object does fall into the unit turn off the power and unplug SB 2000 immediately Contact an authorized SB 2000 service provider for assistance 6 Keep liquids away from SB 2000 Do not operate the Currency Counter if it is wet Also do not touch the Currency Counter if you are wet If a spill occurs turn off the power and unplug SB 2000 immediatel
30. o press BATCH key until your desire batch number is located preset value 100 50 25 20 10 or use four direction keys A VW lt P gt to set any batch number from 1 200 Once your batch number is set press EXIT to escape to Main screen Up down direction keys are used to change batch number with 10 increment and left right direction keys lt 4 are used to change batch number with 1 increment Also note that batch function cannot be turned off in any discriminating mode however it can be changed to DB denomination batching as described below 5 Denomination Batch DB applicable to SDC SORT FACE modes Each Denomination associated Batch function DB is available with SDC SORT and FACE modes and can be activated or deactivated by pressing BATCH key This is how they are organized k SB 2000 Operators Manual V 3 1 22 Once Batch Key is pressed DB message is displayed on LCD screen ensuring activation of the denomination batch function If DB is selected machine will count and batch the desired denomination by pre set batch number For further information on how to set up DB Denomination Batch setting please see below DB Denomination Batch setting In order to set batch number for each denomination activate DB function by pressing BATCH key and then enter into DB setting by pressing CE ENTER key User can set d
31. other end into a standard AC power outlet If you turn on the power switch the machine will display initializing process for second and LCD display shows machine model and software version If there is Service Call number saved by a service provider the Call number will be displayed as below 4 2 Initialization See below first display screen and follow up main menu screen during the initialization process MODEL SB 2000 VER MADE IN KOREA AMROTEC First Display Screen Main Menu Screen SB 2000 Operators Manual V 3 1 13 4 3 Placing bills into the hopper Avoid counting of wet excessively dirty or spoiled banknotes od IN 2 t n F Prior placing banknotes on the banknote hopper check for foreign matter paper chips rubber bands clips dust etc mixed with banknotes and remove them T ra e a Remove folded banknotes or straighten them prior placing them to Note hopper Spread and separate brand new notes well due to slightly adhesive nature of banknotes in a new bundle Align all the four corners and edges of banknotes Any unevenness may cause an error lt Correct Placement gt lt Incorrect placement gt SB 2000 Operators Manual V 3 1 14 4 4 Connecting of External Devices 1 Ho 23e2 PS lt Back view gt 1 Terminal Interface Connection CD 2 SB 2000 can be connected to a PC to upgr
32. rators Manual V 3 1 5 2 2 Installation and Handling of the machine Unpacking After unpacking the SB 2000 Currency Discriminator Counter store the box and packing materials for future shipping Failure to ship the Currency Counter in the original box and packaging will void the warranty Installation 1 Select an appropriate workspace Make sure that the work surface is flat and level away from any heating device such as a radiator away from bright sunlight and as free of dust dirt and smoke as possible This will ensure proper operation and prevent damage to the rubber components of the machine 2 Operate on only the following power sources 120VAC 60Hz USA and North America 3 Connect the power cord to the back of the Currency Counter Plug the cord into the wall outlet 5 When replacing fuses use only the same type and rating Using a higher rated fuse can create a fire hazard Use the product in the following temperature and humidity range a Temperature 0 359 32 95F b Humidity 20 90 without dew condensation SB 2000 Operators Manual V 3 1 6 Installation Spacing Requirement x e Allow sufficient space from peripheral walls and the product as shown on the following Figure e Allow sufficient operation space for inserting and removal of banknotes opening and closing of doors and covers and also allow space necessary for maintenance 3BZ5 ES e zali
33. rn to main screen 6 MOTOR TEST Restricted for Service Professional Authorized SB 2000 Service Professional can check the status of the Main Motor Stacker wheel and motor Clutch and Solenoid using this menu option MANUAL TEST MOTOR A OFF SPOOL 4 CLUCH b OFF OFF SOL V OFF 4 SB 2000 Operator s Manual V 3 1 28 7 SENSOR CHECK Restricted for Service Professional SENSOR HOPPER SEN COUNTA SEN COUNTB SEN COUNTC SEN COUNTD SEN STAKER SEN REJECT SEN Authorized SB 2000 Service Professional can check the status of all sensors Hopper counting stacker and reject sensors using this menu option 8 SPEED Counting speed of the SB 2000 is fixed from the factory and applies to all counting mode including optional Serial number printing function Mode Factory Speed MXED SINGL FACE About 720 NPM ORENT 9 SPOOL SETTING Restricted for Service Technician This menu function is reserved for service technician Users are not recommended to enter into this sub menu This function is to set the speed of SPOOL motor SPOOL MOTOR SPEED LOW MID HIGH To change Spool Motor Setting from Low MID HIGH first enter into the 9 SPOOL SETTING menu using A V and select the proper speed using lt key Once selection is made Press EXIT key to confirm the setting and EXIT key to escape from this menu or EXIT key again to return to main menu SB 2000 Operator s
34. show the lifetime count result After counting number reached maximum number 10 digits on the first line counting number moves to second line as 1 2 etc with 1 increment represent 4 294 967 295 count Press EXIT key again to escape from this menu and return to main screen 18 MODE LOCK SETTING To prevent a mode from changing unintentionally user can disable the MODE by setting MODE LOCK SETTING to ON While this function is ON the MODE key will be deactivated MODE LOCK SB 2000 Operator s Manual V 3 1 33 To turn ON or OFF this function first enter into the 18 MODE LOCK SETTING menu using A and select ON OFF using P gt lt 4 key Once selection is made Press EXIT key to confirm the setting and escape from this menu or press EXIT key again to return to main screen 19 VERSION INFO Trained users or service technician are able to view the machine software and hardware version using this menu This is useful prior loading new software patch to SB 2000 or replacing hardware VERSION INFO HAN IMAGE VER MAIN VER DISP VER To retrieve software and hardware version for the SB 2000 first enter into the 19 VERSION INFO menu using V and LCD display screen will list hardware and software version Press EXIT key again to escape from this menu and return to main screen 20 STATION ID SET User can select each Station ID 1 255 from this menu and this station ID will appear on the
35. sor C Count sensor D Stacker sensor te lt lt Sensor s position gt SB 2000 Operators Manual V 3 1 43 9 1 Error caused by Sensor s breakdown and malfunction Ne _ FEEDING ERROR A FEEDING ERROR FEEDING ERROR C SENSOR JAM B SENSOR JAM C SENSOR JAM D STACKER ERROR Error caused by delivery delay in A part Error caused by delivery delay in B part Error caused by delivery delay in C part Count Sensor A s jamming Sensor breakdown Count Sensor B s jamming Sensor breakdown Count Sensor C s jamming Sensor breakdown Count Sensor D s jamming SENSOR JAM A 8 Sensor breakdown Stacker Sensor s jamming Please amend defective parts after check Roller around of Main motor or Roller at feeder Please replace defective sensor after check condition of Count Sensor A and B Please amend defective part after check Discrimination Part Roller Please replace defective sensor after check condition Count Sensor B and C Please amend defective part after check Transfer plate Part Roller Please replace defective sensor after check condition of Count Sensor C and D Count Sensor A clean Please replace defective sensor after check condition of Count Sensor A Count Sensor B clean Please replace defective sensor after check condition of Count Sensor B Count Sensor C clea
36. the accumulated counting result Choose YES to erase and NO to escape followed by CE ENTER key To return to Main Menu press EXIT key twice SB 2000 Operators Manual V 3 1 41 9 Troubleshooting MIX gt S 65 T MB FEEDING ERROR A ERROR CODE During counting SB 2000 may halt due to certain error conditions An error message will alert user of the condition of error Please review the section 9 1 to solve the error conditions The below diagram summarize the different Error conditions during counting FEEDING ERROR A FEEDING ERROR B Sensor FEEDING ERROR C SENSOR JAM A SENSOR JAM B SENSOR JAM C ee SENSOR JAM D STACKER ERROR REJECT ERROR CF A ERROR CF B ERROR CF ERROR CF D ERROR CF E ERROR CF F ERROR CF G ERROR CF H ERROR Discrimination Part Check lt Figure Action map for Error indicated on Display gt SB 2000 Operators Manual V 3 1 42 B case of a machine malfunction or a stop please look for the error message displays on the screen and follow the solutions steps described under section 9 1 In case of a counterfeit error follow the solutions steps described under section 9 1 In case of a machine malfunction or error jam remove all banknotes from the hopper stacker and from the rear and resume counting by placing banknotes on the hopper Count sensor A Count sensor B Reject sensor 0 gt L Ya d Count sen
37. y Contact an authorized SB 2000 service provider for help SAFETY INSTRUCTIONS The SB 2000 Currency Counter automatically starts operating in certain circumstances Consequently it is important to always follow these precautions 1 Do not wear loose clothing or jewelry while operating the Currency Counter Make sure that your hair does not touch the Currency Counter Do not touch currency that has been placed in the stacker while the motor is running SB 2000 Operators Manual V 3 1 4 4 Turn off the power before performing any maintenance or error corrections that require you to put your hands into the machine Do not allow anything to rest on the power cord line cord or PC interface cable 6 Do not install your machine near walking area ensuring that power plug of the machine does not get unplugged during operation 7 Use supplies or cleaning materials only as directed Keep all supplies and cleaning materials out of the way of children 8 Your machine and the supplies are designed and tested to meet strict safety requirements Included are safety agency examination and approval and compliance to establish environmental standards Warning Hazardous moving parts Keep fingers and other body parts away CAUTION drinks food and other foreign objects away from the Currency Counter ePlacing foreign objects on or into the Currency Counter can interrupt operation of the machine SB 2000 Ope
Download Pdf Manuals
Related Search