Home

Notice - Airis Support

1. right click the item Vow Text in this format and symbol means specific instructions commentary sidelights or any additional information or notes that you should be aware of eng Text in this format and symbol means that failures to comply with the given instructions or information could result in damage to your computer or could cause bodily harm or loss of life Protecting Your Computer Avoid Abusive Handling and Adverse Environment Follow the advice below will help ensure that you get the most out of your Investment Your computer will serve you well if you take good care of it m Do not expose the computer to direct sunlight or place it near sources of heat m Do not subject it to temperatures below 0 C 32 F or above 30 C 86 F Do not expose the computer to magnetic fields Do not expose the computer to moisture or rain Do not spill water or liquid on the computer Do not subject the computer to adverse shock and vibration Do not expose the computer to dust and dirt m Do not place objects on top of the computer to avoid damaging the computer m Do not place the computer on rocky surfaces Here are some ways of taking care of your AC adapter m Do not connect the adapter to any devices other than your computer m Do not let water get into the adapter m Do not block the ventilation airway of the adapter E Keep the adapter in a cool and ventilated place m Do not step on the power cord or plac
2. E Keep the keyboard clean Dust and dirt under the keys could cause them to stick E Configure the keyboard to wait longer before the auto repeat feature starts To adjust this feature Go to Start gt Settings gt Control Panel and double click the Keyboard icon A dialogue box shows up with the adjustable settings for the keyboard 5 9 chapter 5 trouble shooting CMOS Battery Problem A message CMOS Checksum Failure displays during the booting process or the time clock resets when booting E Try to reboot the system a If the message CMOS Checksum Failure appears during the booting procedure even after rebooting it may indicate failure of the CMOS battery If so you need to replace the battery This battery normally lasts two to five years The battery is of type CR2032 3V You may replace it by yourself The battery is located under the System Device Cover on the bottom of the notebook See Chapter 4 for more details chapter 5 trouble shooting Memory Problems The POST does not show an increased memory capacity when you have already installed additional memory u Certain brands of memory module may not be compatible with your system You should ask your vendor for a list of compatible DIMM E The memory module may not be installed properly Go back to Chapter 4 to review the details of this operation The memory module may be defective The O S issues an insufficient memory error message du
3. 825 IEC 825 1 EN60825 EN60825 1 The device is not considered harmful but the following precautions are recommended u Do not open the unit Avoid direct exposure to the laser beam If the unit requires service contact an authorized service center Ensure proper use by reading and following the instructions carefully Do not attempt to make any adjustment of the unit CLASS 1 LASER PRODUCT APPAREIL ALASER DE CLASSE 1 LASERSCHUTZKLASSE 1 PRODUKT Warning Do not attempt to disassemble the cabinet containing the laser The laser beam used in this product is harmful to the eyes The use of optical instruments such as magnifying lenses with this product increase the potential hazard to your eyes For your safety have this equipment serviced only by an authorized service provider B 7 Hi appendix B agency regulatory notices Lithium battery warning Bridge battery warning This computer contains a lithium battery to power the clock and calendar circuitry CAUTION Danger of explosion if battery is replaced incorrectly Replace only with the same or equivalent type recommended by the manufacturer Discard used batteries according to the manufacturer s instructions ATTENTION Il y a danger d xplosion s il y a remplacement incorrect de la batterie Remplacer uniquement avcc unc batterie du meme type ou d un type recommande par le constructer Mettre au rebut les batteries usagees conformement aux instruct
4. When system is off The key allows you to watch DVD movies in the optical drive without having to boot to Windows Additionally Power Cinema application allows you to view photos and play music files in the optical drive as well as in the hard disk drive Please see Appendix c TO LEARN HOW TO USE power Cinema Silent Mode Button When system has already booted to Windows Pressing the key enables the system to lower its power usage therefore turning off the fan to achieve lowest operating noise 1 5 10 EM Chapter 1 getting to know the basics wi way the Power Cinema works is that when the key is pressed the system boots to a Linux based O S and movie player application in a separate hard drive partition In case you have a brand new HDD or when you need to re install O S and Power Cinema please go to Appendix C for installation instructions LED Status Indicator The LED Status indicators reveal the status of these functions Numeric keypad cap lock scroll lock WLAN module enabling and disabling and also the ODD HDD activities See the LED Status Indicator Section for details Keyboard The keyboard is used to enter data It has an embedded numeric keypad and cursor control keys See Keyboard Section for details Suspend Status LED Flashing green light indicates the notebook is in suspend mode See the LED Status Indicator Section for details Battery Status LED The multi color LED indicates the ba
5. based on demand For example Max Battery mode lowers the processor s speed and voltage to conserve power as much as possible 3 7 E chapter 3 battery power amp power management 3 8 Power Options Properties Pe Power Schemes Alarms Power Meter Advanced Hibernate Select the power scheme with the most appropriate settings for this computer Note that changing the settings below will modify the selected scheme Power schemes Portable Laptop ome Office Desk Portable Laptop Presentation Always On Minimal Power Management Max Batter When computer is ZR Plugged in Turn off monitor After 15 mins Turn off hard disks After 30 mins System standby After 20 mins System hibernates After 3 hours Fu batteries After 5 mins After 5 mins After 5 mins After 2 hours In this dialog box you can manually set the LCD and hard drive s time out values in the Plugged in column and in the Running on batteries column Lower time out values will save more battery power Note Also consult Windows user guide for more information on how to use Windows power management functions Note Actual dialogue box shown above may appear slightly different E chapter 3 battery power amp power management Suspend Mode Standby Suspend The system automatically enters this mode after a period of inactivity which is set in the Power Schemes dialog box In Standby mode hardware devices such as d
6. mHard Drive mCombo Drive m DVD R RW or DVD Dual or DVD Multi Standards mKeyboard E Touch pad EChipset E Express Card E 4 in 1 Card Reader Format Support A 4 v Firewire IEEE1394 a TI TSB43AB22A IEEE1394 OHCI Host Controller and Up to 400 Mbps Expandable up to 63 devices in chains v Storage 2 5 inch format hard disk drive 5 25 inch format 12 7mm height fixed module Optional Purchase 5 25 inch format 12 7mm height fixed module Optional Purchase v Keyboard amp Touch pad 86 key QWERTY keyboard with embedded numeric keypad and Windows keys 19 05mm Pitch Built in Touch Pad v Express Card amp Multiple Card Reader Intel ICH6 M Express Card Genesys GL817E Card Reader Single Slot Express Card Hot insertion and removal supported Multimedia Card MMC Secure Digital Card SD Memory Stick MS and MS Pro Card appendix A product specification E Mic In Port E Audio Out SPDIF E Firewire m USB2 0 Port E Ethernet E Modem E S Video mPower In mVGAPort m Card Reader mExpress Card Slot mPrimary Battery Pack MFeature E Adapter AC Input DC Output v Ports and Connectors One Microphone in jack One Headphone SPDIF jack One Firewire IEEE1394 host connector Two USB2 0 compliant connectors One standard network Ethernet connector RJ 45 One modem phone connector RJ11 One S video TV out output connector One DC in connector One 1
7. E Chapter 1 getting to know the basics Modem Your computer comes with a 56K V 92 internal fax modem and a phone jack RJ 11 which is located on the left side of your computer Use a telephone cable to connect the computer to the telephone wall outlet Connecting the Modem 1 Plug one end of the phone line into the modem port located on the side of the computer For EMI compliance you need to clip the included EMI CORE to the phone line 2 Plug the other end of the line into the analog phone wall outlet Depending on where your computer is used you may need to change settings in the modem Correct setting will allow you to maintain a stable connection in a country where its telecommunication system may be different to others To change the modem setting do the following 1 Go to Start gt Settings gt Control Panel and double click on Modem Seitings icon You will see a similar dialog box UNIWILL V 90 Modem properties Speaker Quick connect V 44 More Configuration Modem Helper Modem On Hold Country USA TURKEY a UAE UK VIETNAM x 1 23 E Chapter 1 getting to know the basics 2 Click on the pull down menu and select the country where it is applicable Click on OK to exit 1 24 E Chapter 1 getting to know the basics Ethernet Your computer is equipped with a 10 100Base TX Fast Ethernet network adapter Connect the active LAN cable to the RJ 45 LAN port loca
8. Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver E Connect the equipment into an outlet on a circuit different from that to which the receiver is connected u Consult the dealer or an experienced radio or television technician for help This device complies with Part 15 ofthe FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment IMPORTANT NOTE FCC Radiation Exposure Statement This equip
9. allow a metal object to touch the battery contacts a Handle a damaged or leaking battery with extreme care If you come in contact with the electrolyte wash the exposed area with soap and water If it contacts the eye flush the eye with water for 15 minutes and seek medical attention a Do not charge the battery pack if the ambient temperature exceeds 45 C 113 F B 6 W appendix B agency regulatory notices a To obtain a replacement battery contact your local dealer u Do not expose the battery pack to high storage temperatures above 60 C 140 F u When discarding a battery pack contact your local waste disposal provider regarding local restrictions on the disposal or recycling of batteries u Use only supplied AC Adapter for charging CAUTION Danger of explosion if battery is incorrectly replaced Replace only with same or equivalent type recommended by the manufacturer Discard used batteries according to the manufacturer s instructions or local laws VORSICHT Explisionsgefahr bei unsachgernazen Austausch der Batterie Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ahnlichen Typ Entsorgung gebrauchter Batterien navh Angaben des Herstellers Laser Safety The optical drive used with this computer is certified as a Class 1 laser device according to the U S Department of Health and Human Services DHHS Radiation Performance Standard and International Standards IEC
10. hard disk drive is also correctly seated Remove it and reinsert it firmly and restart your PC Refer to Chapter 4 for details The new HDD may need to be partitioned and reformatted O S and drivers will need to be re installed as well a Check the hard disk indicator LED When you access a file the LED lamp should light up momentarily m The new HDD may be defective or is not compatible 3 If your computer has been subjected to static electricity or physical shock you may have damaged the disk drive The hard drive is making abnormal whining noises E You should back up your files as soon as possible u Make sure the source of noise is indeed from the hard drive and not the fan or other devices The hard disk drive has reached its capacity E Run Disk Cleanup utility in Windows Start gt All Programs gt Accessories gt System Tools gt Disk Cleanup The system will prompt you for what to do E Archive files or programs you no longer use by moving them to an alternative storage medium floppy disk optical record able disk etc or uninstall programs that are no longer in use E Many browsers store files in the hard drive as a cache to speed up the performance Check the program s Online Help 5 5 chapter 5 trouble shooting 5 6 for instructions on decreasing the cache size or on removing temporary Internet files a Empty the Recycle Bin to create more disk space When you delete files Windows saves them
11. into the system To install the DIMM do the following 1 Turn OFF the computer Unhook the AC cord and all cables devices attached to the notebook Remove the battery back 2 Place your hand on a large metal object momentarily to discharge any static electricity Place the notebook on a flat surface and fully close the LCD lid 3 Locate and remove 7 Screw C s on the System Device Cover sy stem Device Cover 4 Remove the System Device Cover The DIMM socket is now seen as shown below 4 7 4 8 chapter 4 upgrading your computer DUAL DDR DIMM SOCKETS 5 If you need to remove an old DIMM from the socket press out on the latches located on both edges of the socket at the same time The DIMM should pop up to an angle of 30 degree see diagram below Pull the DIMM module out of the memory socket Store away the DIMM for the future use lt H gt 6 Install the new DIMM module into the memory socket The DIMM will only fit in one orientation Insert the DIMM at an W chapter 4 upgrading your computer angle of approximately 30 degrees into the empty memory socket Then press it firmly so that the contact edge is driven into the receiving socket Notch 7 Pivot the DIMM until the latches on both sides of the socket snap into place 7 Notice the notch on the DIMM The notches should fit nicely with the socket 8 Put the System Device Cover bac
12. to install PCM Linux you can continue the installation by typing install sh in the command prompt and you will return to step 2 3 as above C 3 W appendix C Using Power Cinema Using Power Cinema PowerCinema is an integrated player for Audio CDs music clips photos DVD VCD movies and video clips To watch or listen to different types of media click a content button on the Welcome page The corresponding function opens allowing you to enjoy the type of media you have selected Finding and Playing Content Click or press Enter to open folders and to play or view media files To go up a folder level click the onscreen up arrow To return toa previous screen within a mediafunction click Return Use the Up Down Left and Right buttons to navigate within PowerCinema To return to the Welcome page from within a media function click the Backspace key on the keyboard Audio CD Click a track to play it or click Play All to play all of the tracks displayed Click Stop to stop music playback To navigate in the list of tracks click Next or Prev Note When you exit this function music playback stops DVD VCD Whenever you move the mouse during playback player controls appear at the bottom of the screen These player controls include the following Play plays the movie Stop stops movie playback Pause pauses movie playback Next jumps to the next movie chapter Prev jumps to the previous movie chapter Fast Forward fast
13. to a network hub via the RJ 45 cable and also conforms to 10 100Base TX transmission protocol 9 Kensington Lock Key Hole A Kensington type security lock latches to this keyhole for anti theft purpose 10 Power Jack DC in The DC out jack of the AC Adapter connects here and powers the computer 11 Ventilation Grill The fan grill is where air is exchanged to dissipate the internal heat Do not block this airway completely 12 Battery Pack The battery pack is a built in power source for the notebook 1 11 E Chapter 1 getting to know the basics Bottom View 1 Ventilation Grill The fan grill is where air is exchanged to dissipate the internal heat Do not block this airway completely i Do not block the Fan Grill outlet Place the machine on hard surface only The bottom case may get very hot 2 Battery Pack and Battery Latch The battery pack is a built in power source for the notebook Slide the battery latch to release the battery pack 1 12 E Chapter 1 getting to know the basics 3 USB Device Optional You may install the USB Thumb Drive into this slot And make sure you put the latch in the locked position Put the latch in the unlocked position before removing the module 4 Wireless LAN Module Bay Optinal E Chapter 1 getting to know the basics You may install the optional wireless LAN module into this slot 5 System Device Cover The system s processor with cooler a
14. to the Recycle Bin The hard disk takes longer to read a file If you have been using the drive for a long period the files may be fragmented Go to Start gt Programs gt Accessories gt System Tools gt Disk Defragmenter to perform a disk defragmentation This operation may take a while E Interrupt requests or problems with other hardware devices may have occupied the CPU and therefore slows down the system performance The files are corrupted l Run the Error checking utility in Windows to check the HDD Double click My Computer Right click C and select Properties Click Check Now in Error checking in Tools chapter 5 trouble shooting Optical Drive Problems The optical drive does not work Try rebooting the system The disk is damaged or files are not readable After you have inserted a CD ROM disk it may take a moment before you can access its content The drive does not read any disks a The CD may not be properly seated in the tray Make sure the disk is firmly seated onto the spindle E The disk is damaged or not readable The disk cannot be ejected a Normally it takes a few seconds to eject the disk If the disk cannot be ejected it may be mechanically jammed Straighten out a paper clip and insert it to a tiny hole next to the eject button This should reject the disk tray If not return the unit for repair Do not forcefully pull on the disk tray The Combo or DVD RW drive opt
15. 0 ports to connect to any USB based peripheral devices Wireless LAN The optional internal Wireless LAN module allows your notebook to connect wirelessly to other 802 11 enabled systems devices or network m Integrated USB Devices Optional The optional USB Thumb Drive gives you added function to the notebook E Chapter 1 getting to know the basics System At A glance Front View Note Your computer may come with the 12 1 display in the wide 16 10 aspect ratio or in the standard 4 3 aspect ratio If your computer comes with the wide 12 1 display there is an extra pair of built in loudspeakers located below the display panel E Chapter 1 getting to know the basics 1 LCD Latch The LCD latches lock unlock the LCD panel 2 Built in Microphone The built in microphone records sound 3 LCD Display The panel is where the system content is displayed 4 Power Suspend Button The power suspend button turns the notebook on and off and it also acts as a system suspend key Press momentarily to turn on the system Press and hold for at least 3 4 seconds to turn off the system How this key behaves can be defined in Start gt Settings gt Control Panel gt Power Options gt Advance menu Press the power suspend button again to return from the suspend mode See Chapter 3 for more details on system suspend function 5 Power Cinema Launch Key Silent Mode Button This is a dual function key Power Cinema Launch
16. 00MB of disc space for Power Cinema You could either use a partition tool or as you install Windows XP when Windows prompts you about creating a partition for Windows during the initial installation process Press C to create a new partition for Windows you should set aside 500MB of disc space For example if your hard drive has 30GB disk space then you should create a partition of 29 5GB for Windows and leave 500MB aside for Power Cinema Now Power Cinema needs to be on the 4 primary partition Otherwise the system cannot boot to Power Cinema when you press the P button W appendix C Using Power Cinema 2 Installation 2 1 Before installing Linux system please make sure you have a 4th partition on the HDD and it should be 500MB If not please create a new one 2 2 Insert the PCM4 Linux installation disc into the optical drive and reboot the system 2 3 When system finished booting from the optical drive you should see a warning message Read it carefully 2 4 In the step above follow the on screen instruction When prompted type YES and then press the Enter key It will take about 2 3 minutes to install the software 2 5 When installation is finish please type poweroff and press the Enter key to shutdown system Press the P button to start Power Cinema 1 If you made a mistake in the steps above for example you didn t type YES in the 4th step the system will exit to a Linux shell If you still want
17. 200 pin DIMM sockets Max 1 GB v Display m 12 1 inch 1280x800 WXGA TFT display Intel 915GM Integrated GMA 900 graphics engine Hardware Motion Compensation and IDCT Supported for MPEG1 2 Playback Direct3D compatible DirectX compatible appendix A product specification mChipset E Audio Codec E Sound Capabilities E Chipset E Transmission Rate E Module E Transmission Protocol EChipset E PnP Function E Flow Control E Speed Selection E Other Features v Audio VT1612A chipset DirectSound 3D EAX 1 0 amp 2 0 compatible A3D I3DL2 compatible AC97 V2 2 compatible 2 or 4 Stereo Speakers v Modem Intel ICH6M integrated Modem Controller with MDC card AC97 V2 2 Modem support V 92 V 90 K56flex for download data speed up to 56Kbps V 34 V 17 V 29 protocol supported v Wireless LAN Intel PRO Wireless 2200 MiniPCl Interface IEEE802 11 B amp G v LAN Ethernet Realtek RTL8201CL Ethernet Phyceiver function for 10 100Base TX network standards Windows 2000 XP Plug and Play compatible Automatic Jam and auto negotiation for flow control Auto Negotiation and Parallel detection for automatic speed selection IEEE 802 3u High performance 32 bit PCI bus master architecture with integrated DMA controller for low CPU and bus utilization Remote Wake up Scheme supported Hot Insertion supported A 3 appendix A product specification Chipset E Capabilities
18. 5 pin VGA connector One 4 in 1 Card Reader slot One Express Card Slot v Battery Pack AC Adapter Li ion 6 Cell pack 10 8Vx 4000 mAh Low battery state with low battery warning beep Uniwill SmartPower Power Management Smart Battery Compliant low battery warning beep Autosensing AC in 100 240V DC out 20V 65W A 5 appendix A product specification v BIOS mPnP Function AMI PnP BIOS mSelf Test Power On Self Test E Auto DRAM auto detection auto sizing Detection L2 Cache auto detection Hard disk type auto detection EPower APM 1 2 Advanced Power Management amp Management ACPI 2 0 Advanced Configuration Power Interface E Security Two Level Password Protections Other 32bit access Ultra DMA PIO5 Mode support Features Multi boot capability gO S Compatible with Microsoft Windows 2000 XP DOS v Physical Specification mDimension 121 LCD model mWeight 292 W x230 D x 25 36 H mm 4 18 lbs 1 9 KG with 12 1 LCD DVD ROM Drive and 6 cell battery pack Environmental Operating Temperature 5 to 35 C 41 to 95 F Limits Operating Humidity 20 to 90 percent RH 5 to 35 C Storage Temperature 20 to 50 C 4 to 122 F A 6 APPENDIX V B AGENCY REGULATORY NOTICES B 1 Hi appendix B agency regulatory notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC
19. C adapter has been obtained using the power cord for the local area However if you travel to a different area and need to connect to a different outlet or voltage you should use one of the power cords listed below To purchase a power cord including one for a country not listed below or a replacement ac adapter contact your local dealer U S and Canada a The cord set must be UL Listed and CSA Certified or C UL Listed The minimum specifications for the flexible cord are 1 No 18 AWG 2 Type SJ and 3 3 conductor a The cord set must have a rated current capacity of at least 10 A u The attachment plug must be an earth grounding type with a NEMA 5 15P 15A 125V or NEMA 6 15P 15 A 250V configuration Japan a All components of the cord set cord connector and plug must bear a PSE mark and registration number in accordance with the Japanese Dentori Law E The minimum specification for the flexible cord are 1 0 75 mm conductors 2 Type VCT or VCTF and 3 3 conductor a The cord set must have minimum rated current capacity of 7 A a The attachment plug must be a two pole grounded type with a Japanese Industrial Standard C8303 15 A 125 VAC configuration Other Countries a The cord set fittings must bear the certification mark of the agency responsible for evaluation in a specific country Acceptable agencies are BSI UK OVE Australia CEBEC Belgium SEMKO Sweden FIMKO Finland DEMKO Denmark N
20. DING YOUR COMPUTER Upgrading the Hard Disk Drive 4 2 3 4 5 Upgrading the System Memory 4 6 7 8 9 5 TROUBLE SHOOTING First Step 5 2 3 Audio Problems 5 4 Hard Disk Problems 5 5 6 Optical Drive Problems 5 7 Display Problems 5 8 Keyboard and Mouse Problems 5 9 CMOS Battery Problems 5 10 Memory Problems 5 11 Modem Problems 5 12 Network Adapter Ethernet Problems 5 13 i 4 Express Card Problems 5 14 Performance Problems 5 15 Firewire IEEE1394 and USB2 0 Problems 5 16 APPENDIX A Product Specification APPENDIX B Agency Regulatory Notices APPENDIX C Power Cinema Installation and User Manual Preface Using This Manual This User s Manual contains general information about the hardware and software setup troubleshooting and technical specifications of the notebook computer Symbols and Conventions The following conventions and symbols are used in this manual m When keys are to be pressed at the same time a plus symbol is used For instance Fn F7 means holding Fn and F7 keys at the same time m When a series of clicking actions is needed in a Windows O S the and gt symbols are used For instance Start gt Settings gt Control Panel gt Display means clicking the Start icon first then the Settings then the Control Panel then the Display icon m When you need to make a selection with the touch pad or mouse you will be asked to select or click or double click
21. E chapter 3 battery power amp power management Power Button Action The notebook PC s power button can be set to turn off the system or activate the suspend mode Go to Start gt Settings gt Control Panel gt Power Options and click on the Advanced tab In the pull down menu select how you wish the power button to work as Power Options Properties Power Schemes Alarms Power Meter Advanced Hibernate 2 paN Select the power saving settings you want to use Options F Always show icon on the taskbar Prompt for password when computer resumes from standby Power buttons When close the lid of my portable computer Stand by When press the power button on my computer Stand by Do nothing Ask me what to do Stand b Shut down OK Cancel Apply Note Actual dialogue box shown above may appear slightly different Warning In the When I close the lid of my portable computer pull down menu DO NOT select Do nothing otherwise the system will still run at high speed while the processor s fan grill is fully blocked by the closed LCD panel The heat will damage the LCD panel 3 11 E chapter 3 battery power amp power management Low Battery Warning You can define when and how the system warns you of its battery low condition Go to the Alarms tab in the Power Options Properties box If you wish to hear audible beeps click on the Alarm Action button and put a ch
22. EC and R amp TTE Directive 1999 5 EC issued by the Commission of the European Community Compliance with these directives implies conformity to the following European Norms EN55022 1998 A1 2 A2 2 LASS B EN61000 3 2 2 EN61000 3 3 1995 A1 2001 EN55024 1998 A1 2001 A1 2 m 1EC61000 4 2 2001 m 1EC61000 4 3 2002 A1 2002 m 1EC61000 4 4 1995 A1 2000 A2 2001 m 1EC61000 4 5 2001 m 1EC61000 4 6 2001 a IEC61000 4 8 2001 a IEC61000 4 11 2001 EN50082 IEC801 2 IEC801 3 IEC801 4 Electro magnetic Immunity EN 300 328 2 EN 300 328 1 EN 301 489 1 EN 301 489 17 ETSI 300 328 ETSI 301 489 Electro magnetic Compatibility and Radio Spectrum Matter TBR21 ETSI TBR21 Terminal Equipment EN60950 IEC60950 I T E Product Safety Canadian Notice This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications Le present appareil numerique nemet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de Classe B prescrites dans le reglement sur le brouillage radioelectrique edicte par le Ministere des Communications du Canada B 4 EI appendix B agency regulatory notices Power Cord Requirement The power cord supplied with the AC adapter should match the plug and voltage requirements for your local area Regulatory approval for the A
23. EMKO Norway SETI Finland EANSW Australia SEV Switzerland IMQ Italy UTE France B 5 W appendix B agency regulatory notices CCC China PSB Singapore PSE Japan BSMI Taiwan B Polish VDE Germany SASO Saudi Arabia a The flexible cord must be of a HAR harmonized type HO5VV F 3 conductor cord with a minimum conductor size of 0 03 square inches a The minimum specification for the flexible cord for Class II product are 1 2X0 75 mm conductors 2 2 conductor cord The cord set must have a current capacity of at least 10 Aanda nominal voltage rating of 125 250 VAC CAUTION MODEL 223Elx IS DESIGNED TO USE WITH THE FOLLOWING AC ADAPTER MODEL ONLY Manufacture LITE ON ELECTRONICS INC LI SHIN INTERNATIONAL ENTERPRISE CORP ELECTRICITY POWER SOURCE EPS INC Model PA 1650 02 65W PA 1650 08 65W 0335A2065 65W F10653 A Telephone lines requirement The appropriate utilization of 26AWG telephone line cord on unit CAUTION Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment CAUTION To reduce the risk of fire use only No 26AWG or larger telecommunication line cord Battery Pack Safety E The battery pack is intended to use only with this notebook Do not disassemble the pack Do not dispose of the battery pack in fire or water To avoid risk of fire burns or damage to your battery pack do not
24. Features High Performance Processor The notebook PC is equipped with the powerful Mobile Intel Pentium M or Celeron M Processor Together with the latest Intel chipset and technologies the system offers advanced performances Advanced Graphic Engine The Intel Integrated GMA900 Extreme3 video processor gives excellent graphic performance The advanced graphic chip also incorporates a hardware based motion compensation engine which gives you smooth MPEG video playback 3D graphics capability also adds realism to PC games LCD Display The computer is equipped with a 12 1 inch TFT in standard format 4 3 aspect ratio or 12 1 inch TFT in Wide format 16 10aspect ratio high resolution display panel for clear test and brilliant colors Expandability The system offers an upgradeable hard disk drive and 2 DDR2 SDRAM sockets for expansion allowing the user to easily increase the storage and system capacities as the need arises E Chapter 1 getting to know the basics Built in Multiple Card Reader There is built in 4 in 1 card reader to access many of the portable media formats SD Cards MS Card MMC Card and MS Pro Card Ethernet Port The system provides built in Ethernet network adapter for high bandwidth network connection Firewire IEEE1394 and USB2 0 ports In addition to a full array of built in I O ports the computer offers IEEE 1394 for ultra high speed connection to high bandwidth digital video devices and USB2
25. Notice The information in this user s manual is subject to change without notice THE MANUFACTURER OR RESELLER SHALL NOT BE LIABLE FOR ERRORS OR OMISSIONS CONTAINED IN THIS MANUAL AND SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES WHICH MAY RESULT FROM THE PERFORMANCE OR USE OF THIS MANUAL The information in this user s manual is protected by copyright laws No part of this manual may be photocopied or reproduced in any form without prior written authorization from the copyright owners Copyright August 2004 All rights reserved Microsoft and Windows are registered trademarks of Microsoft Corporation DOS Windows 95 98 ME 2000 NT XP are trademarks of Microsoft Corporation Product names mentioned herein may be trademarks and or registered trademarks of their respective owners companies The software described in this manual is delivered under a license agreement The software may be used or copied only in accordance with the terms of the agreement This product incorporates copyright protection technology that is protected by U S patents and other intellectual property rights Use of this copyright protection technology must be authorized by Macrovision and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Reverse engineering or disassembly is prohibited Rev 1 0 i 2 TABLE OF CONTENTS PREFACE Symbols and Conventions Protecting Your Computer Avoid Abusive Handli
26. Sector Virus Protection If enabled the following warning message appears when a program attempts to alter the boot sector You may have to enter N several times to prevent the boot sector write Boot Sector Write Possible VIRUS Continue Y N _ The following warning message appears when a program attempts to format the hard disk drive Format Possible VIRUS Continue Y N _ 2 6 EI chapter 2 bios setup and security feature Using Password Protection Two Levels of Password Protection are available The BIOS provides both a Supervisor and a User password If you try to activate both passwords the Supervisor password must be set first The passwords activate two different levels of protection 1 System always asks for password every time it is powered on 2 System asks for password only when you attempt to enter BIOS utility The passwords are encrypted and stored in NVRAM Make sure you write them down or memorize them If you lost the passwords the computer may need to be sent back to the factory orto an authorized service dealer to reset the passwords 2 7 EI chapter 2 bios setup and security feature Power Setup Selections Description Sub menu Power Button On Off On Off When the power button is Mode Suspend pressed the system is turned off Suspend When the power button is pressed the system enters the suspend mode High Enable When Enabled maximum system Performance Dis
27. UTER In this chapter you will learn how to upgrade the DRAM hard disk drive and to install the optional wireless LAN mini PCI RE Warning We strongly recommend you sending your notebook back to your dealer or agent for the specification upgrading When you upgrade your system please turn off the power disconnect the LAN and Modem cable first for your safety After system upgrade please screw all the screws before turn on 4 1 chapter 4 upgrading your computer Upgrading the Hard Disk Drive 4 2 Replacing the original drive with one of larger capacity can increase the hard drive capacity of your computer The computer uses a 9 5 mm height 2 5 inch Ultra ATA 66 100 133 type hard disk Be sure to make a backup copy of all your data before attempting this operation Warning Hard drive upgrade is a delicate process Please observe the following instructions carefully or have a qualified technician install it for you Damages due to mishandling of this procedure are NOT covered by the manufacture s warranty SNE Warning Apply care when handling the hard disk E Do not drop or apply any shock Do not press on the cover u Do not touch the connector with your fingertips m Mishandling of the hard drive can result in permanent loss of data Make a backup copy of the drive s content before you remove it LA Note Certain models that come with the IBM brand hard drive emit a clattering sound when i
28. able performance can be achieved The Mode processor performance is enhanced Long Battery Enable When Enabled maximum battery life can Life Mode Disable be achieved The processor performance is lowered Note The Suspend Mode selection in BIOS only applies to older Windows version such as Windows 3 1 or Windows 95 or NT4 or non Windows operating system In Windows ME 98SE 2000 XP suspend mode and settings are determined by settings in the Power Options Properties Start gt Control Panel gt Power Options 2 8 Mi chapter 2 bios setup and security feature Exit Setup Selections Description Sub menu Saves After you have completed the BIOS Changes and settings select this item to save all Exit settings exit BIOS Setup utility and reboot New system settings will take effect on next power up F10 key can be used for this operation Changes the setup question Load Optimal Defaults Load Optimal Default value for all the setup questions F9 key can be used for this operation Discard N A Discards changes done so far to any of Changes and the setup questions and exit Exit Discard N A Discards changes done so far to any of 2 9 E chapter 3 battery power amp power management CHAPTER V THREE BATTERY POWER amp POWER MANAGEMENT In this chapter you will learn the fundamentals of power management and how to use it to achieve longer battery life 3 1 E chapter 3 batt
29. ack Note To achieve optimal battery performance you may need to do a battery calibration at a 3 month interval To do this 1 Fully charge the battery 2 Then discharge the battery by entering the BIOS setup screen Press F2 key as soon as you turn on the computer And let it remain at the setup screen until the battery runs out 3 Fully charge the battery again E chapter 3 battery power amp power management Using Windows Power Options Windows Power Management provides basic power saving features In the Windows Power Options Properties Start gt Settings gt Control Panel gt Power Options dialogue box you may enter time out values for display and hard disk drive Windows power manager saves power by turning off hard drive after 1 minute of inactivity for example Windows Power Schemes The power management control panel in Windows XP known as Power Schemes is designed to provide the user with an easy to use interface The Power Schemes tab can be found in the Power Options Properties panel that is accessible via the control panel window Schemes are easy to understand based on notebook usage scenarios and control not only processor power usage but other system peripherals as well Go to Start gt Settings gt Control Panel and double click the Power Options icon Always on mode puts the processor into maximum performance mode which provides no power saving The other schemes control processor performance
30. ack case are expected to reach 50 degrees Make sure the air vents are not blocked E If the fan does not seem to be working at high temperature 50 degrees Celsius and up contact the service center x Certain programs that are processor intensive may increase the computer temperature to a degree where the computer automatically slows down its CPU clock to protect itself from thermal damage The program appears stopped or runs very slowly E Press CTRL ALT DEL to see if an application is still responding u Restart the computer This may be normal for Windows when it is processing other CPU intensive programs in the background or when the system is accessing slow speed devices such the floppy disk drive E You may be running too many applications Try to close some applications or increase system memory for higher performance E The processor may have been overheated due to the system s inability to regulate its internal heat Make sure the computer s ventilation grills are not blocked chapter 5 trouble shooting Firewire IEEE1394 and USB2 0 Problems The USB device does not work E Windows NT 4 0 does not support USB protocols 1 Check the settings in the Windows Control Panel Make sure you have installed the necessary device drivers u Contact the device vendor for additional support The IEEE1394 port does not work a Go to Start gt Settings gt Control Panel gt System gt Hardware gt Device M
31. anager You should see an entry which reads Texas Instrument OHCI Compliant IEEE 1394 Host Controllers If it does not exist Windows has not detected the host controller or the device driver has not been installed properly If there is a yellow mark or red cross on the 1394 host controller it may be a device or resource conflict Replace or update the device driver from the factory CD ROM disk or consult Windows manual on how to solve the resource conflict problem E Make sure the cable is fully connected E Make sure you have installed the necessary device drivers u Contact the device vendor for additional support APPENDIXY A PRODUCT SPECIFICATION A 1 appendix A product specification E Processor MCore Logic memory Type E Default E Memory Expansion mLCD Panel E Graphic Accelerator E AGP Bus E Motion Playback mFrame Buffer mOther Features E S Video TV out Encoder v Processor and Core Logic m Intel Pentium M Dothan CPU 1 4 to 2 0 400 MHz FSB 2M L2 Cache m Intel Pentium M Dothan CPU 1 6 to 2 13 533 MHz FSB 2M L2 Cache m Intel Celeron M Operating to 1 70 GHz 400MHz FSB 1MB L2 cache E Intel 915GM Alviso ICH6 M FW82802FBW chipset with graphic audio modem and USB2 0 controllers integrated 533Mhz Pentium M 400 celeron M Front side Bus DDR2 interface v System Memory DDR2 SDRAM 400 533 PC3200 PC4200 compatible 256 512MB 2 5 Volt 64 bit bus Two
32. and the system beeps at 4 second interval When the notebook warns you of its low battery condition you will have about 3 5 minutes to save your current work SNE Warning Do not expose battery packs to temperatures below 0 degree Celsius 32 degree F or above 60 degree C 140F This may adversely affect the battery pack Note Press Fn F3 to turn off the battery warning beep 3 3 E chapter 3 battery power amp power management Installing and Removing the Battery Pack To Remove the Battery Pack 1 Place the notebook bottom side up on a flat and secured surface 2 Push the latch and pull the battery s hard case away from the notebook 3 4 E chapter 3 battery power amp power management To Install the Battery Pack 1 Place the notebook bottom side up on a flat and secured surface 2 Carefully insert the battery pack into the battery compartment of the notebook Charging the Battery and Charging Time To charge the battery while the battery pack is in the notebook plug the AC adapter into the notebook and an electrical outlet The charging time is approximately 4 6 hours when the notebook is turned off and approximately 8 12 hours when the notebook is turned on When the battery is fully charged the battery charge indicator becomes green light on Note If system runs at heavy loading or in a high temperature environment the battery may not be fully ch
33. apter 5 trouble shooting Audio Problems 5 4 No speaker output a Turn up the volume dial located at the right edge of the computer See Chapter 1 for its location E Software volume control is turned down in Microsoft Sound System or is muted Double click the speaker icon on the lower right corner of the taskbar to see if the speaker has been muted or turned down all the way E Most audio problems are software related If your computer worked before chances are software may have been set incorrectly a Go to Start gt Settings gt Control Panel and double click the Sounds and Audio Devices icon In the Audio page make sure that Vinyl AC 97 Audio WAVE is the default playback device Sound cannot be recorded a Double click the speaker icon on the lower right corner of the taskbar to see if the microphone has been muted 1 Click Options and select Properties 2 Select Recording and click the OK button 3 After Click OK button the recording volume control panel will appear Go to Start gt Settings gt Control Panel and double click the Multimedia icon or Sounds and Audio Devices icon In the Volume or Audio page make sure that Vinyl AC 97 Audio WAVE is the default recording device chapter 5 trouble shooting Hard Disk Problems The hard disk drive does not work or is not recognizable If you had just performed a hard disk upgrade make sure the hard drive connector is not loose and the
34. arged You need to continue to charge it with the AC adapter plugged in until the charging LED turns green 3 5 E chapter 3 battery power amp power management 3 6 Checking the Battery Level You can check the remaining battery power in the Windows battery status indicator which is located at the lower right hand corner of the task bar If you do not see a battery or AC in icon on the task tray go to Power Options Properties box and click on the Advanced tab Check off Always show icon on the task bar Alternatively you can access the power meter by clicking the Power Options icon in the Windows Control Panel Prolonging the Battery s Life and Usage Cycles There are ways you can do to prolong the use of battery E Use the AC adapter wherever AC wall outlet is available This will ensure uninterrupted computing E Purchase additional battery pack E Store the battery pack in room temperature Higher temperature tends to deplete the battery s power faster 5 Make good use of the power management function Save To Disk Hibernate saves the most energy by storing current system contents in a hard disk space reserved for this function E The life expectancy of the battery is approximately 300 recharges E See the notices section in the beginning of the user manual on how to care of the battery pack E Read Section Protecting Your Notebook in the beginning of this manual for tips about how to maintain the battery p
35. d to the computer E Check to see the power indicator of the computer is on E Check to see if your keyboard is operational by pressing and holding any key E Check for any incorrect or loose cable connections Make sure the latches on the connectors latch securely on to the receptor end E Be sure you have not performed an incorrect setting on the 5 2 chapter 5 trouble shooting hardware devices in the BIOS Setup utility A faulty setting may cause the system to misbehave If you are not sure of the changes you made try to restore all the settings to factory defaults E Be sure all the device drivers are installed properly For example without the audio driver properly installed the speakers and microphone will not work a If external devices such as USB camera scanner printer do not function correctly when connected to the system it is usually the device s own problem Consult the device s manufacturer first E Some software programs which have not gone through rigorous coding and testing may cause problems during your routine use Consult the software vendor for problem solving m Legacy peripheral are not plug and play capable You need to restart the system with these devices powered up and connected first u Be sure to go to BIOS SETUP and load DEFAULT SETTING after BIOS re flash a Be sure the Quick Key Lockout Switch on the bottom of the computer is not engaged otherwise the quick keys will not work 5 3 ch
36. e following Contains TX FCC ID SAZ 2200BG255 Manual Information That Must be Included The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrate this module The users manual for OEM integrators must include the following information in a prominent location IMPORTANT NOTE To comply with FCC RF exposure compliance requirements The antenna must not be co located or operating in conjunction with any other antenna or transmitter Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by the Manufacture may void the user s authority to operate the equipment Connections to Peripheral Devices Connections to this device must be made with shielded cables with metallic RFI EMI connector hoods to maintain compliance with FCC Rules and Regulations Hi appendix B agency regulatory notices Declaration of Conformity This device complies with Part 15 CLASS B 68 the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation European Notice Products with the CE Marking comply with both the EMC Directive 89 336 EEC and the Low Voltage Directive 73 23 E
37. e heavy objects on top of m Carefully tuck away the power cord and any cables away from pedestrian traffic m When unplugging the power cord do not pull on the cord itself but pull on the plug m Keep the adapter away from children m The total ampere ratings of the equipment plugged in should not exceed the ampere rating of the cord if you are using an extension cord mM The total current rating of all equipment plugged into a single wall outlet should not exceed the fuse rating m Do not connect other AC adapter to your notebook This Notebook uses exclusively the AC adapter Manufacture LITE ON ELECTRONICS INC LI SHIN INTERNATIONAL ENTERPRISE CORP ELECTRICITY POWER SOURCE EPS INC Model PA 1650 02 65W PA 1650 08 65W 0335A2065 65W F10653 A 65W When cleaning the computer observe these steps 1 Power off the computer and remove the battery pack 2 Disconnect the AC adapter 3 Use a soft cloth dampened with water Do not use liquid or aerosol cleaners Contact your Tech support or see your service technician if any of the following occurs m Computer has been dropped or the body has been damaged m Liquid has been spilled into the product m The computer does not operate normally Cleaning the Ventilation Grills It is suggested that you clean the ventilation grills regularly to maintain optimal thermal regulation of the notebook To do this you may use a soft brush or a vacuum cleaner with appropria
38. eck on Sound Alarm Power Options Properties Power Schemes Alarms Power Meter Advanced Hibernate Low battery alarm Activate low battery alarm when power level reaches 0 9 Alam Action Notification Text Action No action Run Program None Critical battery alarm Activate critical battery alarm when power level reaches ox Q Alarm Action Notification Text Action Stand by Run Program None Note Consult Windows user guide for more information on how to use Windows power management functions Note Actual dialogue box shown above may appear slightly different 3 12 E chapter 3 battery power amp power management Power Menu Quick Access Instead of making specific selections in the Power Options Properties box you can quickly and easily specify which pre set power saving function you desire by clicking on the Battery icon at the lower right hand corner of the task bar If you do not see a battery or AC in icon go to Power Options Properties box and click on the Advanced tab Check off Always show icon on the task bar Select Max Battery if you want the system to enter suspend mode more often Or select Always On if your notebook PC is plugged into an AC power source Home Office Desk Portable Laptop Presentation Always On Minimal Power Management Max Battery 1 56 hours 61 Note Actual dialogue box shown above may appear slightly different CHAPTERW FOUR UPGRADING YOUR COMP
39. ery power amp power management IN this chapter you will learn how to operate your notebook on battery power how to handle and maintain the battery pack and learn about the system s power saving features TFT display central processor hard disk drive are the major hardware subsystems that consume the most power Power management determines how these key components should behave to conserve power For example you can have the system turn off its display after 2 minutes of inactivity to save power Efficient power management can help you work longer sessions before having to recharge the battery The Battery Pack Lithium lon Battery Your notebook uses a six cell Lithium lon battery pack that provides power when you don t have access to an AC outlet Note It is necessary that you charge the battery pack for at least 6 hours before using it for the first time Note In the Standby Suspend mode a fully charged battery loses its power in roughly 1 2 day or less When not being used the battery s power will deplete in 1 2 month 3 2 E chapter 3 battery power amp power management Battery Low Power Warning 1 Low Battery Warning Low battery condition occurs when battery power is reduced to 6 The red battery status LED indicator blinks and the system beeps once every 16 seconds or so 2 Very Low Battery Warning Very Low battery condition occurs at 3 power remaining The red battery status LED indicator blinks
40. et the brightness to the lowest comfortable setting Fn F8 2 When working at your desk connect your notebook to an external monitor and disable the internal display Fn F4 3 Do not disable the suspend time outs 4 Ifyou are using AC power and have no external monitor attached change to suspend mode when not in use 1 20 E Chapter 1 getting to know the basics Opening and Closing the Display Panel To open the display push the LCD latch inwardly and lift up the lid Then tilt it to a comfortable viewing position To close the display cover fold it down gently until the LCD latches click into place ng To avoid damaging the display do not slam it when closing Do not place any object on top of the computer when the display is closed 1 21 E Chapter 1 getting to know the basics Audio Subsystem Your computer s audio subsystem is Sound Blaster Pro compatible Adjusting the Volume Manually To turn up the volume press Fn F5 To turn down the volume press Fn F6 Adjusting the Audio Volume in Windows 1 Click the speaker symbol in the task tray in Windows 2 Drag the volume control bar up or down to adjust the volume 3 To temporarily silence the speaker without changing the volume setting click Mute Voice Recording A built in microphone allows you to record sound You will need to use audio processing software to enable the built in microphone For example you may use Microsoft Sound Recorder 1 22
41. forwards movie playback Rewind rewinds movie playback Main Menu goes to the disc s main menu and Quit returns to the Welcome page These controls automatically disappear several seconds after the mouse stops moving To facilitate navigation and media playback use the following hotkeys while watching a DVD VCD movie Left arrow Navigate left in the main menu Up arrow Navigate up in the main menu Right arrow Navigate right in the main menu Down arrow Navigate down in the main menu F Fast forward H Audio L Main menu Enter Play C 4 W appendix C Using Power Cinema N Next End Esc Quit P Previous Beginning Spacebar Pause Q Mute 0 9 Enter numbers 0 9 S Stop A Angle T Step B Scan backward U Subtitles E Step backward Music Clips Use this function to listen to music files in MP3 and WAV formats Click Device to select a media source You can select CDROM for media on a CD USB Devices for media on a removable device or HDD for media in hard disk folders Click a music clip to play it or click Play All to play all of the clips displayed Click Stop to stop music playback To navigate in the list of clips click Next or Prev Note When you exit this function music playback continues Photo Use this function to view photo files in BMP JPG PNG and TGA formats Click Device to select a media source You can select CDROM for media on a CD USB Devices for media on a removable de
42. ge you want to use for display in PowerCinema then return to the main menu in order for the selection to take effect efres Click USB Refresh each time you attach a USB device to your computer in order to enable PowerCinema to read from the device The amount of time required to refresh depends on the device Eject Click Eject to open your computer s CD DVD ROM tray Reboot Click Reboot to restart your computer and enter the Windows partition Battery Status Indicator A battery icon appears on the Welcome page indicating the power source battery or AC adapter your computer is currently using When your computer is using battery power the icon appears as such 3 Approximate battery life is also displayed next to this icon When your computer is using the AC adapter the icon appears as such F C 6
43. gratulations You have now completed the hard drive upgrade When you boot up the PC you may need to create a primary HDD partition and reformat the new drive and re install O S drivers and all the necessary applications 4 5 EI chapter 4 upgrading your computer Upgrading the System Memory Many applications will generally run faster when the computer s dynamic memory capacity is increased The computer provides two DDR memory sockets located underneath the System Device Cover You can increase the amount of memory by replacing the existing one with a dual inline memory module commonly known as SO DIMM of a higher capacity The SO DIMM can be 128MB 256MB or 512MB in capacity The SO DIMM is oftype DDR SDRAM The SO DIMM should PC3200 and PC4200 compliant m Memory upgrade is a delicate process Please observe the following instructions carefully or have a qualified technician install it for you Damages due to mishandling of this procedure are NOT covered by the manufacture s warranty Warning Changing memory while your computer is in suspend or power saving mode may cause permanent damage to the hardware Make sure you turn off the power and unplug the AC cord before proceeding with amemory upgrade Warning You should only use the DIMM module that is approved by the reseller or tne manufacturer otherwise the system may become unstable 4 6 EI chapter 4 upgrading your computer Installing a memory module DIMM
44. heavy objects on the top of notebook This may damage the display 1 Express Card Slot The slot is where Express Card is inserted 2 Stereo Headphone SPDIF out Jack The stereo headphone jack 3 5 mm diameter is where you connect the headphones or external speakers Alternatively you may connect the SPDIF output to an external DTS AC3 or PCM sound processor decoder in your home stereo system 1 10 EM Chapter 1 getting to know the basics ae In some models the SPDIF out feature may not be available Microphone Jack The microphone jack 3 5 mm diameter is where you connect a mircrophone Firewire IEEEE1394 1394 Port This is a high speed serial data port You may connect any Fire wire ready device to this port Yow In some models the Firewire 1394 Port may not be available 5 USB2 0 Port The Universal Serial Bus USB2 0 compliant port allows you to connect a wide variety of devices to your computer at a rate of up to 480 Mbps This port conforms to the lasted USB2 0 plug and play standards TV S Video Port The S Video port permits you to redirect the screen output to a television set or any analog video playback device This TV Port is copyright protected when DVD movie is played the output is scrambled to prevent analog recording Modem Port This is where you plug the phone jack RJ 11 for fax modem E Chapter 1 getting to know the basics functions 8 Ethernet LAN Port The port connects
45. ins manufacture s default settings for the computer s standard operations However there are occasions when you may be required to modify the default settings in the BIOS For example you may need to configure the BIOS power management APM settings if you are using DOS or non Windows operating system The BIOS allows you to set up passwords to limit access to users This is an important feature because a great deal of vital information is carried within the computer nowadays Unauthorized access can be prevented Later in this chapter you will learn how to use this security feature Hi chapter 2 bios setup and security feature Entering the BIOS Setup Screen First turn on the power When the BIOS performs the POST Power On Self Test press F2 key quickly to activate the AMI BIOS Setup Utility Note You may need to press F2 key fairly quickly Once the system begins to load Windows you may have to retry by cycle power on again Leaving the BIOS Setup Screen When you have finished modifying the BIOS settings exit the BIOS It takes a few seconds to record changes in the CMOS BIOS Action Keys Function Key Leaves a sub menu to return to the ESC Exit previous menu OR exits the BIOS setup while saving changes General Help Shows the Help Screen Save and Exit Saves changes and reboots the computer Select a field Selects the next field Select an item Selects the next lower item Selects the next value within a fie
46. ional device cannot record E You need to purchase and install a burner utility program to record files to a blank media 5 7 chapter 5 trouble shooting Display Problems 5 8 The display panel is blank when the system is turned on Make sure the computer is not in the Standby or Hibernate suspend modes The display is turned off to conserve energy in these modes The screen is difficult to read E The display resolution should at least be set to at least space 1024x768 for optimal viewing 1 Go to Start gt Settings gt Control Panel and double click the Display icon 2 Under the Settings page set screen resolution to at least 1024x768 and choose at least 256 colors The screen flickers E It is normal if the display flickers a few times during shutting down or powering up chapter 5 trouble shooting Keyboard and Mouse Problems The built in touch pad performs erratically E Make sure there is no excess perspiration or humidity on your hand when using the touch pad Keep the surface of the touch pad clean and dry E Do not rest your palm or wrist on the surface of the touch pad while typing or using the touch pad The built in keyboard accepts no input E If you are connecting an external keyboard to the system the built in keyboard may not work Try restarting the system The characters on the screen repeat while type E You may be holding the keys down too long while you re typing
47. ions du fabricant VORSICHT Explosionsgefahr bei unsachgemBen Austausch der Batterie Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ahnlichen Typ Entsorgung gebrauchter Batterien nach Angaben des Herstellers Der Arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 betragt 70dB A oder weniger Zum Netzanschlua dieses Gerates ist eine geprufte Leitung zu verwenden Fur einen Nennstrom bis 6A und einem Gerategewicht groBer 3kg ist eine Leitung nicht leichter als 1 HO5VV F 3G 0 75mm 2 2X0 75 mm conductors einzusetzen Die Steckdose muB nahe dem Gerat angebracht und leicht uganglich sein CAUTION Thispart ishot Be C are ful VORSICHT Diese Flache wird sehr heiss When you see this symbol be careful as this spot may be very hot W appendix C Using Power Cinema A _P P E N D X V C USING POWER CINEMA W appendix C Using Power Cinema Software Installation Power Cinema resides in a separate HDD partition to Windows C 2 When you press the P button while the notebook is off the computer boots to the Linux environment and launches the Power Cinema application If you are required to re install Windows O S or when you have purchased a new or upgraded HDD you need to observe the following steps before installing Power Cinema 1 Partitioning Assuming you are starting with a fresh hard drive or the hard drive is removed of its previous partitions You need to reserve 5
48. isplay panel and hard disk are turned off to conserve energy Hibernate Suspend In this mode all system data are saved in the hard disk before powering down When this mode is activated all system state and contents are saved to the hard disk drive after a period of inactivity defined by the user No power or very little power is drawn from the battery module under this mode However depending on how much RAM has been installed on your computer the amount of time the system requires to restore all its previous contents can range from 5 to 20 seconds For Windows 2000 XP users hibernation is handled by the operating system therefore no special disk partition or disk file is necessary If you wish to activate Hibernate mode you need enable Hibernate Support in the Hibernate tab of the Power Options menu 3 9 E chapter 3 battery power amp power management Power Options Properties Power Schemes Alarms Power Meter Advanced Hibernate When your computer hibemates it stores whatever it has in A memory on your hard disk and then shuts down When your computer comes out of hibemation it returns to its previous state Hibernate J Enable hibernation Disk space for hibernation Free disk space 5 546 MB Disk space required to hibernate LA Note Do not install or remove the memory module when the system is in the suspend mode Note Actual dialogue box shown above may appear slightly different 3 10
49. k and tighten 7 Screw C s Congratulations You have just completed the memory upgrade When you boot up the computer you should expect to see an increase in DRAM capacity 7 Your computer has been tested with a wide range of DIMM on the market However not all memory modules are compatible Check with your system vendor for a list of compatible DIMM for your computer 4 9 CHAPTERW FIVE TROUBLE SHOOTING In this chapter you will learn how to solve common hardware and software problems 5 1 chapter 5 trouble shooting Your computer has been fully tested and complies with the system specifications before shipping However incorrect operations and or mishandling may cause problems This chapter provides a reference for identifying and correcting common hardware and software problems that you may encounter When you encounter a problem you should first try to go through the recommendations in this chapter Instead of returning the computer and waiting for repair you may easily solve the problems by considering the following scenarios and possible solutions If the error continues contact your reseller for service information Before taking further actions consider the following suggestions a Check to see if the problem persists when all the external devices are removed u Check to see that the green light indicator on the AC adapter is lit E Check to see the power cord is properly plugged to the wall outlet an
50. ld Selects the nextfield _ Select an item Selects the next upper item Higher value Selects the next value within a field 2 3 EI chapter 2 bios setup and security feature Modifying the BIOS Settings The AMIBIOS setup main menu is subdivided into sub menus Each menu item is described in this section Main Setup Under this menu you may change time date and view basic processor and system memory information Selections Description Sub menu N A Type in the current date in MM DD YY format N A Type in the current date in HH MM SS format Advanced Setup gt IDE Configuration Selections Description Sub menu Hard Disk Primary Master is where BIOS tries to boot from first The primary master controls the hard drive ATAPI CDROM The secondary master controls the ATAPI CD ROM drive Note The sub menu is not selectable Press enter to view information of the storage device 2 4 E chapter 2 bios setup and security feature Item Selections Sub menu Description TouchPad Support Enabled Disabled Enable or disable the built in touchpad LCD AutoDimm Function Enabled Disabled Enabled The LCD backlight automatically decreases when the AC Adapter is unplugged from the wall Disabled This function is disabled BIOS Post Beep Sound Enable Disable Boot Setup gt Boot Settings Configuration Selections Sub men
51. ment complies with FCC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Uniwill declares that 223Elx with wireless card Intel PRO Wireless 2200BG is limited in CH1 CH11 by specified firmware controlled in USA The highest SAR test value 0 045W kg This device is intended only for OEM integrators under the following conditions Hi appendix B agency regulatory notices 1 The transmitter module may not be co located with any other transmitter or antenna As long as conduction above is met further transmitter test will not be required However the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed for Notebook IMPORTANT NOTE In the event that these conditions can not be met for example certain laptop configurations or co location with another transmitter then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product In these circumstances the OEM integrator will be responsible for re evaluating the end product including the transmitter and obtaining a separate FCC authorization End Product Labeling The final end product must be labeled in a visible area with th
52. ne handset on the line and placing a phone call If you do hear abnormal noise try to make the modem connection with a different line or contact your local telephony company for service u Make sure the cable connection is firm E Try a different receiver number and see if the problem persists chapter 5 trouble shooting Network Adapter Ethernet Problems The Ethernet adapter does not work a Go to Start gt Settings gt Control Panel gt System gt Hardware gt Device Manager Double click on Network Adapters and check if Realtek RTL8139 810x Family Fast Ethernet NIC appears as one of the adapters If it does not exist Windows has not detected the Realtek RTL8139 810x Family Fast Ethernet NIC or the device driver has not been installed properly If there is a yellow mark or red cross on the network adapter it may be a device or resource conflict Replace or update the device driver from the factory CD ROM disk or consult Windows manual on how to solve the resource conflict problem Make sure the physical connections on both ends of the cable are good E The hub or concentrator may not be working properly Check to see if other workstations connected to the same hub or concentrator is working The Ethernet adapter does not appear to operate in the 100Mbps transmission mode E Make sure the hub you are using supports 100Mbps operation E Make sure that your RJ 45 cable meets the 100Base TX requirements E Make su
53. ng and Adverse Environment Chapter Summaries 1 GETTING TO KNOW THE BASICS Performance Features 1 2 3 System at a Glance 1 4 Front View 1 4 5 6 7 8 Rear View 1 9 10 11 Bottom Views 1 12 13 14 AC Adapter 1 15 LED Status Indicators 1 16 Keyboard Features 1 17 Function Quick Keys 1 17 Windows Keys 1 18 Embedded Numeric Keypad 1 18 Touch Pad 1 19 Graphic Subsystem 1 20 Adjusting the Display Brightness 1 20 Extending the Life of the TFT Display Panel 1 20 Opening and Closing the Display Panel 1 21 Audio Subsystem 1 22 Adjusting the Volume in Windows 1 22 Voice Recording 1 22 Modem and Modem Settings 1 23 24 Ethernet Adapter 1 25 2 BIOS SETUP AND SECURITY Entering the BIOS Setup Screen 2 3 Leaving the BIOS Setup Screen 2 3 BIOS Action Keys 2 3 Modifying the BIOS Settings 2 4 Main Setup 2 4 Advance Setup 2 4 5 Boot Setup 2 5 6 Security Setup 2 7 8 Power Setup 2 9 Exit Setup 2 9 3 BATTERY POWER amp POWER MANAGEMENT The Battery Pack 3 2 Lithium lon Battery Technology 3 2 Battery Low Power Warning 3 3 Installing and Removing the Battery Pack 3 4 5 Charging the Battery and Charging Time 3 5 Checking the Battery Level 3 6 Prolonging the Battery s Life and Usage Cycles 3 6 Using Windows Power Options 3 7 Windows Power Schemes 3 7 8 Suspend Modes 3 9 10 Power Button Action 3 11 Low Battery Warning 3 12 Power Manual Quick Access 3 13 4 UPGRA
54. o know the basics Windows Keys Your keyboard also has two Windows keys 1 Start Key This key allows you to pull up the Windows Start Menu at the bottom of the taskbar 2 Application Menu Key This key brings up the popup menu for the application similar to a click of the right mouse button Embedded Numeric Keypad Press Fn Num Lk to enable the embedded numeric keypad The numbers are printed in upper right corner of a key in a color different from the alphabets This key pad is complete with arithmetic operators Press Fn Num Lk to revert to normal character keys I i Je I ce m LL IRRE _ LI EE 1 18 E Chapter 1 getting to know the basics Touch Pad The built in touch pad which is a PS 2 compatible pointing device senses movement on its surface As you move your fingertip on the surface of the pad the cursor responds accordingly The following items teach you how to use the touch pad 1 Move your finger across the touch pad to move the cursor 2 Press buttons to select or execute functions These two buttons are similar to the left and right buttons on a mouse Tapping on the touch pad twice produces is similar to clicking the left button of a mouse Function Left Button Right Equivalent Tapping Action Button Execution Click twice Tap twice at the same speed as quickly double clicking the mouse button Selection Click once Tap once Drag Click and hold Tap twice q
55. re the Ethernet cable is connected to the hub socket that supports 100Base TX mode The hub may have both 100Base TX and 100Base T sockets chapter 5 trouble shooting Express Card Problems 5 14 Now Some system may not have the Express Card Slot option Express Cards do not function E Make sure you have properly installed the driver for the card E Consult the card s manual or contact the vendor for trouble shooting The Express card cannot be recognized E Windows NT4 0 does not support Express Card function You may need an external program for this E Make sure the card is fully inserted the outer end of the card should be even with the edge of the computer m Remove and insert the PC card again E Make sure there is no IRQ conflict with the card See Windows on line help for solving IRQ conflicts E Reboot the computer and see if the problem persists E The card may be defective Try the card on another system if possible Windows crashes or freezes when you remove the Express card E Make sure you have lt Stop gt the Express card before removing it Double click the Safely Remove Hardware icon at the lower right corner of the task bar and select the card you wish to stop When you click lt Close gt in few seconds Windows will prompt you to remove the card chapter 5 trouble shooting Performance Problems The computer becomes hot In a 35 C environment the certain areas of the computer s b
56. ring operation E This is often a software or Windows related problem A program is draining the memory resources E Close the application programs you re not using and restart the system E You need to install additional memory module For instructions go to Chapter 4 Upgrading Your Computer 5 11 chapter 5 trouble shooting Modem Problems 5 12 The built in modem does not respond E Make sure the modem driver is loaded properly L Go to Start gt Settings gt Control Panel gt Phone and Modem Options and go to Modems tab Make sure SmartLink 56K Voice Modem or Uniwill V 92 Modem is listed Otherwise click the Add button to add the modem drive which is located in the factory CD ROM or floppy diskette m Go to Start gt Settings gt Control Panel gt System and click Device Manager button in the Hardware page to check for possible resource or driver conflict See Windows on line help or manual for how to handle such problems E Make sure the phone line which the computer is connected to is working Connection difficulties E Be sure to disable Call Waiting on the phone line E Be sure to have the correct country setting where your computer is used Start gt Settings gt Control Panel gt Modem Settings gt Configuration In the Country Area pull down menu select the appropriate country setting E Excessive line noise might cause the connection to be dropped To check this put the regular pho
57. ssembly hard disk drive and DDR memory module are located under the case cover The system memory and HDD can be upgraded 1 14 E Chapter 1 getting to know the basics AC Adapter 2 DC out Connector The DC out connector docks to the power jack DC in on the computer Adapter The adapter converts alternating current into constant DC voltage for the computer AC Plug The AC plug plugs to the AC wall outlet eng Make sure you are using a standard 3 prong AC wall socket with a ground pin If not you may feel a slight tingling sensation on any of the computer s metal parts such as the I O ports This is caused by leakage current when the AC adapter is not properly grounded via the ground pin However the amount of leakage current is within the safety regulation and is not harmful to human body E Chapter 1 getting to know the basics LED Status The LED Status Indicator displays the operating status of your notebook When a certain function is enabled an LED will light up The following section describes its indication System Status Indicator LED Graphic Indication Symbol ig Green light indicates the WLAN module is active D Blinking green light indicates the notebook is in suspend mode Blinking orange light indicates the battery X 0 is being charged Blinking red light indicates the battery power is low when the system is turn ON Persistent green light indicates the battery is f
58. t is being rattled This is a normal condition EI chapter 4 upgrading your computer Upgrading the Hard Disk Drive To replace the hard disk drive do the following 1 Turn OFF the computer Unhook the AC cord and all cables devices attached to the notebook Remove the battery back 2 Place your hand on a large metal object momentarily to discharge any static electricity 3 Locate and remove Screw A 4 Remove HDD Cover Tmi Screw System Device Cover 5 In order to prevent the collision with the thermal module when the HDD is being removed three screws fixed to the thermal module need to be removed first 4 3 EI chapter 4 upgrading your computer 6 Lift the thermal module away from the bay and carefully separate the module from the thermal connector 7 Remove 3 Screw B s 8 Lift the HDD module away from the bay and carefully separate the module from the HDD connector HDD Connector TI ii HDD Module g 9 Locate and remove 4 Screw C s from the HDD module 10 Remove the metal case 4 4 EI chapter 4 upgrading your computer um LE 8 11 Re attach the metal cover to the new hard drive and tighten 4 Screw C s Note the green PC board of the hard disk drive is facing against the metal case 12 Re attach the HDD module to the HDD connector 13 Put the HDD cover back and re attach Screw A Con
59. te head adapter to remove the dust buildup on the ventilation grills i 7 Chapter Summaries The following is a Summary of the available chapters and appendices in this manual Chapter 1 Getting to Know the Basics In this chapter you will learn the basic operations and features of your computer It gives you a general understanding of the components of your computer Chapter 2 BIOS Setup Security In this chapter you will learn how to change various firmware settings and what the settings mean Also you will learn how to take advantage of the built in security feature provided by the BIOS Chapter 3 Battery Power amp Power Management In this chapter you will learn the fundamentals of power management and how to use them to achieve longer battery life Chapter 4 Upgrading Your Computer In this chapter you will learn how to upgrade the system memory and the hard disk drive Chapter 5 Trouble Shooting In this chapter you will learn how to solve common hardware and software problems Appendix A Product Specification In this section you will find a list of the computer s system specifications Appendix B Agency Regulatory Notices In this section you will find the general electro magnetic and safety regulatory information cCc HAPTER Y O N E GETTING TO KNOW THE BASICS This chapter introduces the features and components of the computer E Chapter 1 getting to know the basics Performance
60. ted on the left side of the computer This allows you to access and transmit data in the local area network Connection to the network Use Unshielded Twisted Pair UTP Ethernet cable only 1 Insert one end of the UTP cable into the network connector until the connector snaps securely into the receptacle 2 Either connect the other end of the cable to an RJ 45 jack wall outlet or to an RJ 45 port on a UTP concentrator or hub in the network Cabling Restriction for Networks The following restrictions should be observed for 100 1000BASE TX networks 1 The Maxine cable run length is 100 meters m 328 feet ft 2 For 100 Mbps operations use Category 5 wiring and connections YEE Consult Windows manual and or Novell Netware user s guide for the software installation configuration operation of the network 1 25 Hi chapter 2 bios setup and security feature C HAPTER V T W_O BIOS SETUP AND SECURITY FEATURE In this chapter you will learn how to enter the BIOS Setup Menu and manipulate various hardware control settings You will also learn how to use the built in security features 2 1 EI chapter 2 bios setup and security feature 2 2 The Setup Utility is a hardware configuration program built into your computer s BIOS Basic Input Output System It runs and maintains a variety of hardware functions It is a menu driven software which allows you to easily configure and change the settings The BIOS conta
61. ttery status of the notebook See the LED Status Indicator Section for details Built in Stereo Speakers The built in speakers output the sound in stereo E Chapter 1 getting to know the basics 11 Touch Pad The touch pad is a built in pointing device with functions similar to a mouse 12 USB2 0 Port The Universal Serial Bus USB2 0 compliant port allows you to connect a wide variety of devices to your computer at a rate of up to 480 Mbps This port conforms to the latest USB2 0 plug and play standards 13 4 in 1 Card Reader The 4 in 1 Card Reader supports SD Card MS Card MMC Card and MS Pro Card Yow In some models the Card Reader may not be available 14 USB Device Optional You may install the USB Thumb Drive into this slot 15 Optical Drive and Disk Eject Button and Manual Eject Key Hole If your computer comes with the Combo drive DVD RW DVD RW or DVD Dual drive you may save data onto a CD R CD RW or DVD RW disc Press the eject button to eject the disk tray The manual eject keyhole allows you to manually eject jammed disk 16 External VGA Port The 15 pin VGA analog port is for connecting the external CRT 1 7 E Chapter 1 getting to know the basics monitor or projector 17 Built in Stereo Speaker If your system comes with the 12 1 inch wide aspect ratio panel there is an additional pair of speakers built in E Chapter 1 getting to know the basics Rear View Warning Do not place any
62. u Enabled The system beeps when performing POST on boot Disabled The beep is disabled Description Disabled Enabled gt Boot Device Priority Item Selections Sub menu Enabled The system skips certain tests while booting This shortens the boot up time Disabled The system performs full tests while booting Description 1st Boot Device 2nd Boot Device Removable Dev Intel UNDI PXE 2 Hard Drive CD DVD Set the type of device for the 1st drive BIOS attempts to boot from If Intel UNDI PXE 2 is selected system will attempt to load boot sector from the Ethernet port Set the type of device for the 2nd drive BIOS attempts to boot from 2 5 Mi chapter 2 bios setup and security feature ar If you select Intel UNDI PXE 2 the system will attempt to boot from the network Note When the BIOS performs POST you may also press F12 Key to enable the Boot Device selection menu You may choose CD DVD Hard Drive or Intel UNDI PXE 2 as the first storage device to boot from If you have already connected a USB Floppy Disk Drive before powering up it will appear as a Removable Device in the Boot Device selection menu Security Setup gt Boot Settings Configuration Item Selections Description Sub menu Change N A Install or Change the Password Supervisor Password Change N A Install or Change the Password User Password Xow About Boot
63. uickly and on the to drag the second tap hold finger to the touch cursor pad to drag the cursor Access Click once Context Menu Move One Page Up or Down Tips on Using the Touch Pad 1 The double click speed is timed If you double click too slowly your notebook responds as if you single clicked twice 2 Keep your fingers dry and clean when using the touch pad Also keep the surface of touch pad clean and dry to prolong its life 3 The touch pad is sensitive to finger movements Hence the lighter the touch the better the response Heavy touch does not produce better response 1 19 E Chapter 1 getting to know the basics Graphic Subsystem Your computer uses a high performance 12 1 inch active matrix TFT panel with high resolution and multi million colors for comfortable viewing The Intel Integrated GMA900 Extreme video graphics accelerator which is Microsoft DirectX 9 compatible performs graphic rendering at a lighting fast speed Adjusting the Display Brightness The notebook uses special key combinations called hot keys to control brightness Press Fn F7 to increase the brightness Press Fn F8 to decrease the brightness Now To maximize your battery operating time set the brightness to the lowest comfortable setting so that the internal backlight uses less power Extending the Life of the TFT Display Device Observe the following guidelines to maximize the life of the backlight in the display 1 S
64. ull LED off Dark indicates the system is without battery Green light indicates the hard drive and amp or optical drive is being accessed a Green light indicates the numeric keypad 1 is activated Green light indicates the cap lock is activated Green light indicates the scroll lock is activated p Persistent blue light indicated the system is in the Power Cinema mode under Linux O S Or persistent blue light indicates in silent Mode under Windows 1 16 Keyboard Features Function Keys Quick Keys Graphic Symbol E Chapter 1 getting to know the basics System Control D Enters Suspend Mode Pi Turns of the battery warning beep off or on Ol Changes Display Mode LCD only CRT only and LCD amp CRT q Fn F5 Turns Speaker Volume up Fn F6 Turns Speaker Volume down Fn F7 Increases Display Brightness Fn F8 Decreases Display Brightness Fn Num Lk Enables the embedded keypad to work in numeric mode The keys act like numeric keypads in a calculator Use this mode when you need to do a lot of numeric data entry An alternative would be to connect an external numeric keypad Fn Scr Lk Press the Fn Scr Lk key and then press tor to move one line up or down Ve For various system controls press the Fn Function key and the Fx key simultaneously 1 17 E Chapter 1 getting t
65. vice or HDD for media in hard disk folders Click a photo to view it Click Slideshow to view a slideshow of the photos in the current directory When the Subfolders option is selected images in all of the subfolders contained in the selected directory are also displayed in the slideshow When this option is not selected the slideshow plays only the photos in the directory you have selected Press the Backspace key on the keyboard to exit the slideshow ideo Clips Use this function to watch video files in AVI M1V M2V MPG and MPEG formats Click Device to select a media source You can select CDROM for media on a CD USB Devices for media on a removable device or HDD for media in hard disk folders C 5 W appendix C Using Power Cinema Click a video clip to play it Whenever you move the mouse during playback player controls appear at the bottom of the screen These player controls include the following Play plays the movie Stop stops movie playback Pause pauses movie playback and Quit returns to the Welcome page These controls automatically disappear several seconds after the mouse stops moving Settings There are settings in PowerCinema to allow you to fine tune its performance to your machine and your personal preferences DVD SPDIF Select the DVD AC3 SPDIF option for multi channel sound Select the DVD PCM SPDIF option for 2 channel sound Language Select the langua

Notice - Airis Support

Contents

Download Pdf Manuals

Related Search

Related Contents