ELAR 162 TRI PAR - Amazon Web Services
Contents
1. PCBO504D LJBOO98B TERMINAL BLOCK POWER INPUT POWER OUTPUT www ElationLighting com 41 OElation Professional Los Angeles Ca 19 Power supply Power consumption LED Configuration IP Rating DMX Channels DMX Drive Color Mixing Beam Angle Field Angle Luminance Dimmer Strobe Lamp Life Operating Temperature Max Ambient Temperature Weight Dimensions Intertek 3104374 LISTED ELAR 162 TRI PAR TECHNICAL SPECIFICATIONS 100V 277V 50 Hz 60Hz Maximum 150W 54 x 3 Watt 18 x Red 18 x Green 18 x Blue IP65 3 4 6 or 8 Channel mode Standard DMX 512 5 pole IP Rated Locking Connector Pin 3 Pin 2 Ground 7 Pin 1 RGB Color Additive Mixing 20 41 Beam Angle Standard 8 Lens 43 6 Standard 8 Lens 8 780 Lux 812 FC at 8 1m Continuous Dimming 0 100 Electronic Strobe 0 25 Fps 100 000 Hours Rated Life 25 C 45 C 113 F 45 C 7 Kgs 15 4Lbs 267 x 232 x 277 mm 10 51 x 9 13 10 9 CONFORMS TO UL STD 1573 CERTIFIED TO CSA STD C22 2 NO 166 MODEL ELAR 162 TRI PAR 100 277 50 60Hz 150W Made in PRC US SUITABLE FOR WET LOCATIONS NOTFOR RESIDENTIAL USE DISCONNECT FROM MAIN SUPPLY BEFORE SERVICING NOTFOR HOUSEHOLD USE IMPROPRE AL USAGE DOMESTIQUE EMPLACEMENTS MOUILLES Please Note Specifications and improvements in the design of this unit and this manual ar2. 2 35 13 Lens 9 38 14 Cleaning 39 15 40 16 Photometric 42 17 Dimensional Drawings ceci a da E 43 18 Circuit 44 19 Technical esee eee 45 Elation Professional Los Angeles Ca 2 www ElationLighting com ELAR 162 TRI PAR 1 GENERAL INFORMATION INTRODUCTION Congratulations you have just purchased one of the most innovative and reliable LED fixtures on the market today The ELAR 162 TRI has been designed to perform reliably for years when the guidelines in this booklet are followed Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit These instructions contain important information regarding safety during use and maintenance UNPACKING Thank you for purchasing the ELAR 162 TRI PAR by Elation Professionale Every ELAR 162 TRI PAR has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for damage and be sure all accessories necessary to operate t
3. 000 15 99 9 95 CEDT ON OFF Edit program via controller EDIT Elation Professional Los Angeles Ca 20 www ElationLighting com ELAR 162 TRI PAR Remarks 1 2 3 If the fixture does not receive a DMX signal the menu display will flash repeatedly TIME Adjust the hold time for each scene in built in chase programs FADE Adjust the fade time between each scene in the built in programs 9 1 MODE Function Mode 9 1 1 lt ADDR gt DMX address setting This function is used to set or adjust the fixture s starting DMX address Every device controlled by DMX has to have a unique starting address The addressing feature is what allows DMX to function properly The DMX address of a fixture is what allows it to communicate with a controller properly The DMX addressing also allows the fixture to ignore any DMX information coming from the controller that is not meant specifically for the fixture Because each fixture is connected in a daisy chain fashion it is imperative to assign a proper and unique starting DMX address to each and every fixture The DMX address is non destructive and will remain in the fixture s memory even when the power to the unit is switched off Memory is backed up and retain by an internal power source that should last about five years For proper DMX addressing see DMX Addressing on page 25 of this user manual VALU Display the DMX 512 value of each chann
4. ETATION ELAR 162 TRI PAR Elation Professional 6122 S Eastern Ave Los Angeles Ca 90040 www elationlighting com Rev 09 14 2011 visage Version 1 0 ELAR 162 TRI PAR Elation Professional Los Angeles Ca 1 www ElationLighting com ELAR 162 TRI PAR TABLE OF CONTENS 1 General 3 ese e eee nemen erret 3 Em 3 c Customer 2 3 d Warranty 3 2 Safety occorre eve tete onus Sr apa Coke od deas dui Pius eR Ore 5 EET 7 4 General 8 5 OVERVIOWS MM 9 6 Mounting and Installati m MH 12 7 Understanding DMX u u e eels o Dn de Dade 15 a DMX tcr na 15 DMX lerminator ccce card 16 c 3 to 5 Pin 17 d Fixture 16 8 Display Indicatots eterne 19 9 Display Men uu u eem tetendit ne a REPE UU RES 20 10 DMX Addressing nerunt ii 25 a Remote DMX Addressing 25 EE 27 12 Working with Built In
5. Press MODE ESC the display shows C 01 Select CEDT by pressing the UP or DOWN buttons Press MODE ESC the display shows OFF Press UP the display will read ON Press MODE ESC the display shows SCO2 You successfully downloaded the first scene gt WN 9 Adjust the Step time as described above 10 Callup the second scene in your controller now 11 Repeat steps 5 11 until all desired scenes are downloaded 12 Press MODE ESC to exit The number of steps can be defined under STEP and the scenes can be called up under RUN Elation Professional Los Angeles Ca 26 www ElationLighting com ELAR 162 TRI PAR 10 DMX ADDRESSING Setting the DMX address After the fixture is turned ON it will immediately complete a reset process that test all the fixture s functions When the reset process concludes the LCD will display the fixture s current DMX address If the fixture is not receiving a DMX signal the display will flash continuously To set or adjust a DMX address please follow the procedure below 1 Toggle through the menu by pressing the Up and Down buttons until the display reads Addr XXX Tap the enter button to make changes to the address 2 While the display is flashing use the UP and DOWN buttons to select a new address Once the new address has been selected lock the new address into the fixture s memory by pressing the ENTER button The DMX address is non vol
6. 1 the third unit to OElation Professional Los Angeles Ca 17 www ElationLighting com ELAR 162 TRI PAR 7 3 4 and so on Note During start up the ELAR 162 TRI will automatically detect whether a DMX data signal is being received or not If a DMX data signal is being received the display will show A XXX XXX representing the actual DMX address If the fixture is not receiving a DMX signal the display will flash A XXX XXX representing the actual DMX address If your fixture is connected to a DMX controller and the display is flashing not receiving a DMX signal please check the following The 3 pin or 5 pin XLR plug cable with DMX signal from controller may not be connected or is not inserted completely into the DMX input jack DMX controller is switched off or defective The DMX cable from the controller merging with included IP Rated Cable adapter is not connected securely The DMX cable or connector is defective A DMX terminator has been inserted into the last fixture in your DMX chain Elation Professional Los Angeles Ca 18 www ElationLighting com ELAR 162 TRI PAR 7 8 DISPLAY LED INDICATOR The ELAR 162 TRI PAR has a LED indicator on the display This indicator is designed to give a quick visual indication of the fixtures DMX status The illustration below details the functionality of the LED indicators DMX OK NO DMX The LED indicator r
7. 3 Never look directly into the light source You risk injury to your retina which may induce blindness 4 For safe operation follow the Installation guide described in chapter six of this manual Operating the ELAR 162 TRI without suited safety aids such as safety cables or clamps can increase the risk of damage and or personal injury 5 Qualified and certified personnel should only perform installation 6 When mounting this fixture use only the original rigging points included with this fixture Any structural modification will void the original manufactures warranty and may increase the risk of damage and or personal injury 7 Do not attempt to operate this fixture if the power cord has become damaged or frayed 8 Never open this fixture while in use 9 This device falls under protection class Therefore it is essential that the device be grounded properly 10 Qualified personnel should perform all electrical connections 11 Be sure the available voltage matches the voltage requirements of the unit Be sure the power cord is never crimped or damaged If the power cord is damaged replace it immediately with a new one of similar power rating Elation Professional Los Angeles Ca 5 www ElationLighting com ELAR 162 TRI PAR 12 Always disconnect from main power before performing any type of service or any cleaning procedure 13 Only handle the power cord by the plug Never pull out the p
8. The ELAR 162 TRI carries a two year 730 days limited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper and included in the shipping container If the unit is under warranty you must provide a copy of your proof of purchase invoice Items returned without a R A number clearly marked on the outside of the package will be refused and returned at customer s expense You may obtain a R A number by contacting customer support at 323 582 3322 Elation Professional Los Angeles Ca 4 www ElationLighting com ELAR 162 TRI PAR 2 SAFETY INSTRUCTIONS To guarantee proper and consistent operation it is important to follow the guidelines in this manual Elation Professional will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual 1 Always be sure that the fan and the air inlets remain clean and are never blocked Allow about 6 15cm between this fixture and other devices or a wall to allow for proper cooling See page 12 2 Never touch the fixture during normal operation
9. at the sole discretion of Elation Professionale All products covered by this warranty were manufactured after January 1 1990 and bare identifying marks to that OElation Professional Los Angeles Ca 37 www ElationLighting com ELAR 162 TRI PAR effect E Elation Professionale reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured F No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by Elation Professionale in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall Elation Professionale be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product G This warranty is the only written warranty applicable to Elation Professionale Products and supersedes all prior warranties and written descriptions of warranty terms
10. and conditions heretofore published OElation Professional Los Angeles Ca 38 www ElationLighting com 16 PHOTOMETRIC DATA Beam angle 20 41 Field angle 43 6 of Red LEDS LENS 8 Intensity LUX 3660 849 2 371 1 Y Beam opening m e 0 36 0 72 0 80 1 60 Beam angle 20 41 3 Distance m 1 08 20 41 Diameter m 2 40 43 6 Diameter m Field angle 43 6 of Blue LEDS LENS 8 Intensity LUX 723 198 2 91 Beam opening m E uy 1 2 3 Distance m 0 36 0 72 1 08 20 41 Diameter m 0 80 1 60 2 40 43 6 Diameter m OElation Professional Los Angeles Ca 39 Beam angle 20 41 ELAR 162 TRI PAR Field angle 43 6 of Green LEDS LENS 8 Intensity LUX 6060 1633 2 735 Beam opening m 1 2 0 36 0 72 0 80 1 60 Beam angle 20 41 Az Y n a 3 Distance m 1 08 20 41 Diameter m 2 40 43 6 Diameter m Field angle 43 6 of Full LEDS LENS 8 Intensity LUX 8780 2199 2 960 Beam opening m 1 2 0 36 0 72 0 80 1 60 s 3 Distance m 1 08 20 41 Diameter m 2 40 43 6 Diameter m www ElationLighting com 17 DIMENSIONAL DRAWINGS G We i Am Y D ELAR 162 TRI PAR CIRCUIT SCHEMATIC 18 FAN H PCB0409C
11. 6 191 220 internal program 7 221 255 gradient effect NA Shutter strobe 0 31 Led trun off 32 63 Led turn on 64 95 Strobe effect slow to fast NA NA 7 96 127 Led turn on 128 159 Pulse effect in sequences 160 191 Led turn on 192 223 Random strobe effect slow to fast 224 255 Led turn on OElation Professional Los Angeles Ca 30 www ElationLighting com ELAR 162 TRI PAR General dimming speed 0 255 dimming O Black 255 100 NA 4 6 8 speed from slow to fast when running internal programs speed from slow to fast when running gradient effect OElation Professional Los Angeles Ca 31 www ElationLighting com ELAR 162 TRI PAR 12 WORKING WITH BUILT IN PROGRAMS The fixture comes equipped with a built in DMX recorder that allows custom programs to be installed and recalled directly from the fixture s control board Programs can be created and stored using the fixture s control board or by using an external DMX controller The following instructions will detail the procedures for using the on board system menu as well as using a DMX compliant controller Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Part 1 Part 2 Part 3 Part 1 Part 2 Part 3 Part 1 Part 2 Part 3 Memory Statistics Quick Access Programs Pr
12. TRI PAR VER Software Version This function will display the current firmware version 9 3 MANL Manual Fixture Settings This function allows the each of the eight DMX channels to be controlled manually This will allow the fixture to be preset to a specific color or built in program without the use of a DMX console 9 4 TIME Operating Hours These functions will detail different time functions associated with the fixture lt LIFE gt 0000 9999 Hours This function tracks the running time of the fixture from the point it was last cleared Where XXXX represents the total number of running hours This time is none destructive and will remain in the fixtures memory indefinitely Use this time to track rentals or show durations lt CODE gt Clear run time access code This lock out code prevents the current run time from being erased accidently The access code is 038 lt CLFE gt Clear Fixture Run Time This function resets the run time to zero 9 5 Edit Internal Program Settings The fixture comes equipped with a built in DMX recorder that allows custom programs to be installed and recalled directly from the fixture s control board Programs can be created and stored using the fixture s control board or by using an external DMX controller For detailed instructions on how to complete this task please see Working with Built In Programs Section 12 Page 35 Elation Professional Los Angeles C
13. a 24 www ElationLighting com ELAR 162 TRI PAR 9 5 1 Select program This function allows the user to select one of ten of the user defined built in programs This program is then accessed in Function Mode under Program Run 9 5 2 Edit program This function allows the user to edit the built in programs 9 5 3 Edit Scenes This function allows the user to edit or define the actual scenes that are stored in the user defined built in programs that are accessed in the previous step 9 5 4 REC Auto save function 9 5 5 CEDT Edit program using a external controller Editing procedure 1 Using the control board only 1 2 3 Access the main menu Tap the UP button until EDIT is displayed and press ENTER The display will show SC 01 this stands for the scene number For example SC 01 is displayed it means you will be editing scene 1 press ENTER You can change the scene number by tapping the UP button Press ENTER the display will show C 01 this represents the channel number If C 01 is displayed you will be editing the fixture s channel 1 value of the selected scene press ENTER You can change the channel number by tapping the UP button The display will show the DMX value for the channel that is being edited It will be displayed as 11 it stands for Channel 11 of the editing scene the DMX value is Adjust the DMX value by tapping the UP button until y
14. atile and will remain in the fixture s memory even when the power to the unit is switched off Memory is backed up and retain by an internal power source that should last about five years Remote DMX addressing RDMX Address Via DMX This function allows the DMX address to be changed remotely from a DMX console This setting requires special settings for both the controller and the fixture This function may be turned on and off and is ON be default Follow the procedure listed below to access the RDMX functions Fixture Settings 1 Access the main menu and use the UP or DOWN to get to the Personality menu then press ENTER 2 Once in the Personalities menu tap the UP or Down to get to the Status Settings menu press ENTER 3 Once in the Status Settings tap the UP or Down to get to the Address via DMX function and press ENTER 4 Address via DMX is the function that turn the RDMX function on and off Press ENTER and be sure the function is turned on 5 Press the UP button to display ON to activate this function or OFF to deactivate this function OElation Professional Los Angeles Ca 27 www ElationLighting com ELAR 162 TRI PAR 6 Press ENTER to confirm 7 Press MODE ESC to return to the main menu Controller Settings 1 Set the DMX value of channel 1 to a value of 7 2 Set the DMX value of channel 2 to a value of 7 or 8 When channel 2 is set to 7 you can adjust the starting a
15. cenes memory You can repeat the procedure for all functions listed below Auto Program Allows access to all of the fixture s DMX traits Red adjust all of the red LED values Green adjust all of the green LED values Blue adjust all of the blue LED values Strobe adjust the strobe Dimmer adjust the dimmer intensity Scene Time set the hold time for the scene Input By Out this function will store a scene from an external DMX console See the next section for scene editing via an external DMX controller Step 1B Building Scenes from an External DMX Controller The fixture includes a simple built in DMX recorder This recorder allows you to build a scene using your own DMX console That scene can then be sent to the fixture and be stored inside one of the fixture s scene storage banks Many people may find this procedure easier and quicker than using the on board menu functions as in Step 1 To store a scene from an external DMX controller follow the procedures below Using your DMX control build and store scenes as you normally would Once you have built all your required scenes enter the fixtures main menu and toggle to Step 2 Editing Programs The control will store a maximum of 10 programs A program can store one or a maximum of 64 scenes Keep in mind that a scene can only be access when it is stored inside one of the 10 available programs Follow th
16. cluding parts replacement are within the terms of this warranty Elation Professionale will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in its original package No accessories should be shipped with the product If any accessories are shipped with the product Elation Professionale shall have no liability what so ever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which Elation Professionale concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the Elation Professionale factory unless prior written authorization was issued to purchaser by Elation Professionale if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintenance cleaning or periodic check up During the period specified above Elation Professionale will replace defective parts at its expense and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of Elation Professionale under this warranty shall be limited to the repair of the product or replacement thereof including parts
17. ddress between 1 and 255 When set to 8 you can adjust the starting address between 256 and 511 Use channel to set your desired DMX starting address For example you want to set the starting address to 57 set channel 1 to a value of 7 set channel 2 to a value of 7 and use channel 3 to set your address to 57 by selecting a channel value of 57 Example 2 If you want to set the starting address to 420 set channel 1 to a value of 7 channel 2 to 8 and channel 3 to 164 256 164 420 4 Wait for approximately 20 seconds for the unit to complete the address reset function Elation Professional Los Angeles Ca 28 www ElationLighting com ELAR 162 TRI PAR 11 DMX TRAITS DMX Operation Notes The fixture will function in DMX mode whenever the unit is receiving a DMX signal Please note that this will override all manual settings This unit will keep and retain the last DMX command in the event of DMX signal failure To reset the fixture you must turn the power off DMX CHANNEL TRAITS The chart below and on the preceding pages outlines the different DMX traits for the four different DMX modes DMX channel s functions and their values Mode Channel Value Function 3CH 4CH 6CH 8CH j 4 i Red LED__ 0 255 Red O Black 255 100 Red 2 2 9 Green LED 0 255 Green 0 Black 255 100 Green Blue LED _ 0 255 Blue 0 255 100 Blue Color Tempe
18. dily available at most electric stores The following chart details a proper cable conversion 3 Pin XLR Female Out 5 XLR Male In Data True signal Pin 3 Fixture DMX addressing All fixtures should be given a DMX starting address when using a DMX controller so the correct fixture responds to the correct control signal This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the back of the fixture You can set the same starting address for all fixtures or a group of fixtures or set different address for each individual fixture Be advised that setting all you fixtures to the same DMX address will subsequently control all fixtures in the same fashion in other words changing the settings of one channel will affect all the fixtures simultaneously If you set each fixture to a different DMX address each unit will start to listen to the channel number you have set based on the quantity of control channels DMX channels of each fixture That means changing the settings of one channel will only affect the selected fixture In the case of the ELAR 162 TRI which is up to a three channel fixture you should set the starting DMX address of the first unit to 1 the second unit to 4 3
19. e subject to change without any prior written notice OElation Professional Los Angeles Ca 42 www ElationLighting com Rev 09 14 2011 visage Elation Professional 6122 S Eastern Ave Los Angeles CA 90040 323 582 3322 323 832 9142 fax www ElationLighting com Info ElationLighting com Version 1 0
20. e procedure below to build an internal program Access the main menu and toggle to Edit Programs which is menu function 8 Then tap the ENTER button and toggle to Program 1 menu function 8 2 1 When you get to the Program 1 function tap the ENTER button The screen will then change to Edit Steps 01 this will be menu function 8 2 1 1 Use the UP and DOWN buttons to toggle through the scenes created in Step 1 Press the Elation Professional Los Angeles Ca 33 www ElationLighting com ELAR 162 TRI PAR ENTER button to add a scene to the program Tapping the Enter button will automatically lock the selected scene into the programs memory Repeat the process until all the desired scenes have been added to the program Each program can store a maximum of 64 scenes To test the program access Program Test in the Program Edit menu function Step 3 Playing a Program To initiate a program follow the procedure below Access the main menu and use the Up and Down to toggle to Function Mode and tap the Enter button In the next screen select Auto Program and tap the Enter button There are now two selections Master and Alone Select Master when running multiple fixtures in a master slave configuration See section 10 2 Master Slave Operation on page 33 for proper set up instructions Select Alone when running a single fixture or when multiple fixtures in stand alone
21. el With this function you can display the DMX 512 value of each channel The display will automatically detail the changing DMX values as they are received from the controller SLAV Slave setting for Master Slave Operation With this function you can define the device as slave for operation in Master Slave mode Each slave setting will have a different function for a dynamic lightshow without a controller RDMX Address via DMX This function allows the DMX address to remotely be adjusted from a DMX console This setting requires special settings for both the controller and the fixture RDMX is on by default For operational instructions please OElation Professional Los Angeles Ca 21 www ElationLighting com ELAR 162 TRI PAR see Section 10 Page 25 of this manual Remote DMX addressing 9 1 2 RUN Internal Program Settings This function allows the internal programs to run in either stand alone or master salve mode In Master mode the fixture will send DMX data to other fixtures connect via the DMX chain In Alone mode the fixture will operate as a single fixture The program for this mode is selected in the Select program section of the control menu You can set the number of steps under Edit program You can edit the individual scenes under Edit scenes With this function you can run the individual scenes either automatically i e with the adjusted Step Time 9 1 3 DISP Menu Display Set
22. epresents DMX signal Ifthe indicators is on a clean DMX signal is present If the indicator is off there is no DMX signal present Elation Professional Los Angeles Ca 19 www ElationLighting com ELAR 162 TRI PAR 9 DISPLAY MENU Default settings shaded 001 VALU AXXX DMX address setting SADBR gt SLAv ON OFF Setas Slave RDMX ON OFF 7 address via DMX lt RUN gt DEG Run Auto program MODE VALU D XX D 00 DXXX Display DMX value ON OFF Flip display lt gt DON JONOFF 7 Delay shutting off LED display Key lock Press the MENU button LOCK ON OFF for 3 seconds to activate lt gt 6 DMXchannel Mode lt gt OFF HOLD UTO Status while there is no DMX MOD1 MODE2 Set dimmer mode lt gt ONOFF Power on to preserve the MANL data V 1 0 V 9 9 Software version R XXX 000 255 G XXX 000 255 B XXX 000 255 MANL x O Manual adjust intensity P XXX 000 255 S XXX 000 255 D XXX 000 255 LIFE 0000 9999 HOURS otal fixture runtime hours TIME CODE CXXX Passcode to clear last run time 038 CLFE ON OFF Clear last run time hours STEP S 01 S 48 1 Selectsteps of program R XXX 000 255 G XXX 000 255 000 255 XXX 000 255 M XXX 000 255 P XXX 000 255 Edit the internal scenes S XXX 000 255 D XXX 000 255 FADE XXX
23. erform two functions 1 When split it can be used as a floor stand bracket 2 Used to secure a mounting clamp for truss mounting Main Power Input Lead This lead is the main power input lead When the unit is the first in a chain or the only fixture to be used be sure to use the power starter Elation Professional Los Angeles Ca 10 www ElationLighting com ELAR 162 TRI PAR cable that converts a standard Edison 3 prong to the IP rated twist lock connector When jumping from fixture to fixture be sure to only use Elation IP rated power connectors to maintain the IP rating 11 DMX In Lead This lead is the main DMX input lead When the unit is the first in a chain or the only fixture to be used with a DMX controller be sure to use the DMX starter cable that converts a standard 3 pin XLR DMX connector to the IP rated twist lock connector that is used on the fixture When jumping from fixture to fixture be sure to only use Elation IP rated DMX cables to maintain the IP rating Elation Professional Los Angeles Ca 11 www ElationLighting com ELAR 162 TRI PAR 7 6 MOUNTING AND INSTALLATION Cautions For added protection mount the fixtures in areas outside walking paths seating areas and away from areas were unauthorized personnel might reach the fixture Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture
24. he fixture have arrived intact In the event damage has been found or parts are missing please contact our customer support team for further instructions Inside the box you should find the fixture a IP rated power cable IP rated DMX cables in and out a safety cable and this manual Please do not return this unit to your dealer without first contacting customer support at the number listed below CUSTOMER SUPPORT Elation Professionale provides a customer support line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www elationlighting com for any comments or suggestions For service related issue please contact Elation Professionale Service Hours are Monday through Friday 9 00 a m to 5 00 p m Pacific Standard Time Voice 323 582 3322 Fax 323 832 9142 E mail support elationlighting com Forum www ElationLighting com forum Warning To prevent the risk of fire and reduce the risk electrical shock do not attempt to operate this fixture with the lens cover removed Elation Professional Los Angeles Ca 3 www ElationLighting com ELAR 162 TRI PAR Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself Doing so will void your manufactures warranty Please do not discard the shipping carton in the trash Please recycle whenever possible WARRANTY REGISTRATION
25. installation must always be secured with a secondary safety attachment such as an appropriate safety cable To avoid injury never stand directly below the device when mounting removing or servicing the fixture Refer to regulations BGV C1 formerly VBG 70 and DIN VDE0711 217 for proper installation in Europe To ensure proper installation only qualified staff should attempt installation Mounting points Overhead mounting requires extensive experience including amongst others calculating working load limits a fine knowledge of the installation material being used and periodic safety inspection of all installation material and the fixture If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury CAUTION Be sure a qualified electrician performs all electrical connections Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Elation Professional Los Angeles Ca 12 www ElationLighting com ELAR 162 TRI PAR Mounting The ELAR 162 TRI PAR is fully operational in any mounting position hanging upside down side mounted or set on a flat level surface etc Be sure this fixture is kept at least 0 5m 1 5 feet away from any flammable materials decoration etc When clamp mounting always use and install the supplied safety cable as an added safet
26. ional Los Angeles Ca 8 www ElationLighting com ELAR 162 TRI PAR 5 FIXTURE OVERVIEW 7 1 a 78 PERE amp UJ l EN 2 A sa EN r 17 AV cu AA OElation Professional Los Angeles Ca 9 www ElationLighting com 10 ELAR 162 TRI PAR LED Lens Assembly The lens assembly may be user replaced in the event repair is needed or a different beam angle is required LED Display 4 segment menu display Used to display the DMX address as well as all other menu functions Power Output Lead This lead is used to jump power to another ELAR 162 TRI Please do not daisy chain power for more than 16 fixtures To maintain the integrity of the IP rating only use proper Elation IP rated power cables DMX Out Lead This lead is used to send an incoming DMX signal to the next fixture in the DMX chain To maintain the integrity of the IP rating only use proper Elation IP rated DMX cables MENU Button This button is used to access the fixtures menu functions Up Button The up button is used to toggle forward through the menu functions and settings Down Button The down button is used to toggle backwards through the menu functions and settings Enter Button The enter button is used to enter in to a certain menu function or to lock a menu setting in to memory Yoke Assembly This yoke is designed to p
27. lug by tugging the wire portion of the cord 14 Please be aware that damages caused by modifications to the device are not subject to warranty Important Notice Damages resulting from the disregard of safety and general user instructions found in this user manual are not subject to any warranty claims Elation Professional Los Angeles Ca 6 www ElationLighting com ELAR 162 TRI PAR FEATURES e P65 Rated Fixture Low power consumption e Minimal heat emission e Maintenance free operation e Equipped with 54 3 Watt 18 x red 18 x green 18 x blue e 100 000 hours rated LED life e Linear RGB Color Mixing infinite color possibilities 20 41 Beam Angle 43 6 Field Angle 8 Lens USITT DMX 512 Complaint Preprogrammed colored macros Strobe effect with a maximum flash rate of 25fps DMX controlled operation or stand alone operation with Master Slave function 7 built in programs can be called up via DMX controller 48 preprogrammed scenes per program Four DMX Modes 3 DMX channels 4 DMX channels 6 DMX channels 8 DMX channels default DMX control via standard DMX controller e Upgradable firmware via Elation E Loader Data Pack Electronic Switching Power Supply 100 240 Flicker free operation for television and film Compact design fits in 12 box truss 0 100 Dimming two dimming options linear amp standard Elation Professional Los Angeles Ca 7 www Elatio
28. mode See section 10 1 Stand Alone Operation on page 32 for proper set up instructions The 3 Slave groups run the Auto Program in certain time segments as shown in the following diagram Part 1 EEE y Part 2 s F Part 3 Elation Professional Los Angeles Ca 34 www ElationLighting com ELAR 162 TRI PAR 13 LENS REPLACEMENT The ELAR 162 TRI PAR comes with a removable front cover that allows the lens assembly to be changed out to achieve different beam angles Lens cover is held in place by four 1 4 turn locking fasteners To remove the cover 1 Turn the locking fasteners in a counter clockwise direction 2 Once the fasteners are loose lift the cover straight up to expose the inner lens see illustration below 3 Locate the 5 securing screws on the inner cover and remove them 4 Remove the inner cover to access the lens kit see second illustration below Once the lenses are changed reassemble in reverse order Unscrew the 4 screws Unscrew the 5 screws OElation Professional Los Angeles Ca 35 www ElationLighting com ELAR 162 TRI PAR 14 CLEANING AND MAINTENANCE Consider the following points during normal service and inspection 1 Be sure all screws and fasteners are securely tightened at all times Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall 2 Electric power supply cables must
29. nLighting com ELAR 162 TRI PAR 4 GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage in nightclubs in theatres and other types of architectural installations Do not attempt operation or installation without a proper knowledge on how to do so Consistent operational breaks will ensure that the fixture will function properly for many years to come Do not shake the fixture around Avoid brute force when installing or operating the fixture While choosing an installation location please be sure that the fixture will not be exposed to extreme heat moisture or dust The minimum distance between the fixture and a wall or flat surface should be at least 0 5 meter about 1 5ft See page 12 Always install the fixture with an appropriately rated safety cable When installing the fixture in a suspended environment always be sure to use mounting hardware no less than M10 x 25 mm also be sure the hardware is only inserted in the yoke s mounting holes Do not attempt to operate this fixture until you have familiarized yourself with all of its functions Do not permit operation by persons not qualified for operating this type of architectural fixture Most damages are the result of improper operation Please use the original packaging to transport the fixture in for service For your own safety please read this user manual carefully before installing the device OElation Profess
30. not show any damage material fatigue or sediments Never remove the ground prong from the power cable Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed CAUTION Disconnect from mains before starting maintenance operation We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no user serviceable parts inside this fixture please refer all other service issues to an authorized Elation service technician Should you need any spare parts please order genuine parts from your local dealer OElation Professional Los Angeles Ca 36 www ElationLighting com ELAR 162 TRI PAR 15 2 YEAR LIMITED WARRANTY A Elation Professionale hereby warrants to the original purchaser Elation Professionale products to be free of manufacturing defects in material and workmanship for a period of two years 730 days from the date of purchase This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service send the product only to the Elation Professionale factory All shipping charges must be pre paid If the requested repairs or service in
31. ogram Part 3 Total Number of Programs 10 Maximum Number of Steps Scenes per a Program 64 Total Number of Scenes Steps 250 Step 1 Building Scenes The control will store a maximum of 250 scenes These scenes are then used to create the programs A program can store one or a maximum of 64 scenes Keep in mind that a scene can only be access when it is stored in a Program If you wish to build a static scene a scene consisting of no movement for a logo or gobo projection the scene must be stored inside a program To build a scene follow the instructions below e Access the main menu and toggle to Edit Programs which is menu function 8 Then tap the ENTER button and toggle to Edit Scenes menu function 8 3 e When you get to the Edit Scenes function tap the ENTER button The screen will then change to Edit Scene 001 this will be menu function 8 3 1 You can then press the ENTER button to begin to edit scene 1 or use the UP and DOWN buttons to toggle to access scenes 2 250 Once in the scene edit screen you have access to the functions listed below Tapping the ENTER button will instantly allow you to change the values of the selected function in real time The values can be adjusted from 0 250 Once you achieved your desired value tap the ENTER button once again to automatically Elation Professional Los Angeles Ca 32 www ElationLighting com ELAR 162 TRI PAR lock the value into the s
32. or Y your DMX connections unless you are using an approved DMX splitter such as the Elation Opto Branch 4 or DMX Branch 4 o X VE saie A AS 552 y NE Q an N SY lt DMX512 CL 120 Ohms DMX controller DMX 512 connection with DMX terminator A DMX terminator should be used in all DMX lines especially in longer runs The use of a terminator may avoid erratic behavior in your DMX line A terminator is a 120 ohm 1 4 watt resistor that is connected between pins 2 and 3 of a male XLR connector DATA and DATA This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line Using a line terminator Elation part DMX T PACK will decrease the possibilities of erratic behavior 1200 Termination reduces signal errors and ON avoids signal transmission problems 1 interference It is always advisable 2 em to connect a DMX terminal Resistance Mb li 120 Ohm 1 4 W between PIN 2 DMX S and PIN 3 DMX of the last fixture OElation Professional Los Angeles Ca 16 www ElationLighting com ELAR 162 TRI PAR 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for DATA transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used these adaptors are rea
33. ort for Digital Multiplex This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers DMX allows all makes and models of different manufactures to be linked together and operate from a single controller This is possible as long as all the fixtures and the controller are DMX compliant A DMX controller sends the DMX data instructions to a fixture allowing the user to control the different aspects of an intelligent light DMX data is sent out as serial data that travels from fixture to fixture via data IN and OUT leads located on the fixtures most controllers will only have output jacks DMX Linking To ensure proper DMX data transmission always use proper DMX cables and a terminator When using several DMX fixtures try to use the shortest cable path possible Never split a DMX line with a Y style connector The order in which the fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in the DMX chain at the beginning at the end or anywhere in the middle The DMX controller knows to send data assigned to address 1 to that fixture no matter where it is located in the DMX chain The ELAR 162 TRI PAR can be controlled via DMX 512 protocol The ELAR 162 TRI PAR is a fixture that can operate in 3 4 6 or 8 DMX channels see pages 28 35 for the different DMX
34. ou get the expected effect for this channel 7 Press ENTER to enter the editing of the other channels of the scene 8 Repeat steps 5 8 until you finish setting all the DMX values for all the channels of this scene each scene can have 16 channels maximum Elation Professional Los Angeles Ca 25 www ElationLighting com ELAR 162 TRI PAR 9 Once all the channels are completed the display will begin to flash TIME this indicates the time needed to run this scene 10 Press ENTER to edit the time needed the display shows TXXX XXX represents the time needed to run this scene For example 002 means scene 1 needs 0 4 seconds to run T 15 means this scene needs 3 0 seconds to run Note is always 0 2 seconds not one second 11 Adjust the time needed by tapping the UP button 12 Press ENTER to save the settings for the scene you are editing the display will change to the next scene automatically 13 Repeat steps 3 12 to edit other scenes you can edit and save 48 scenes maximum 14 Press MODE ESC to exit and save your edited scene into the fixtures internal memory The number of steps can be defined under EDIT and the scenes can be called up under Run To run the scenes see page 30 Editing procedure 2 Using an external controller 1 Call up the first scene in your controller now Select 5 01 by pressing the UP or DOWN buttons Press MODE ESC the display shows 5 01
35. rature NA NA 4 4 0 No function 1 255 Color Temperature 2700K 7200K NA NA 5 5 Color macros 0 No function 1 7 Color Macro 1 8 15 Color Macro 2 16 23 Color Macro 3 24 31 Color Macro 4 32 39 Color Macro 5 40 47 Color Macro 6 48 55 Color Macro 7 56 63 Color Macro 8 64 71 Color Macro 9 72 79 Color Macro 10 Elation Professional Los Angeles Ca 29 www ElationLighting com ELAR 162 TRI PAR 80 87 Color Macro 11 88 95 Color Macro 12 96 103 Color Macro 13 104 111 Color Macro 14 112 119 Color Macro 15 120 127 Color Macro 16 128 135 Color Macro 17 136 143 Color Macro 18 144 151 Color Macro 19 152 159 Color Macro 20 160 167 Color Macro 21 168 175 Color Macro 22 176 183 Color Macro 23 184 191 Color Macro 24 192 199 Color Macro 25 200 207 Color Macro 26 208 215 Color Macro 27 216 223 Color Macro 28 224 231 Color Macro 29 232 239 Color Macro 30 240 247 Color Macro 31 248 255 Color Macro 32 NA internal programs 0 10 without internal program 11 40 internal program 1 41 70 internal program 2 71 100 NA NA 6 internal program 3 101 130 internal program 4 131 160 internal program 5 161 190 internal program
36. s the UP button to select ON to activate this function or OFF to e qe deactivate this function Press ENTER to confirm Press MENU to return to the main menu 9 2 SET Fixture Personality Settings These functions set specific running modes and operating parameters lt CHAN gt DMX Mode settings This function allows the fixture to run in different DMX channel modes Four modes are available 3 channel 4 channel 6 channel or 8 channel See DMX Traits beginning on page 28 for a detailed explanation of the different DMX modes lt FAIL gt DMX Fault Protection This function dictates how the fixture will operate in the event DMX signal is suddenly lost while operating in DMX mode The three fail safe modes are 1 OFF which will blackout all light output 2 HOLD which will hold the last DMX command or 3 AUTO which will put the fixture in sound active mode lt DFSE gt Restore Default This function is used to restore the factory settings of the device All settings will be set back to the default values shaded Any edited scenes will be lost lt DIMR gt Set dimmer mode With this function you can Set dimmer mode lt POHO gt Power on to preserve the MANL settings With this function you can activate The fixture will return to the scene manual set before automatically after re power on OElation Professional Los Angeles Ca 23 www ElationLighting com ELAR 162
37. tings This function allows the internal programs to run in either stand alone or master salve DMX chain In Alone mode VALU Display the DMX 512 value of each channel This function will electronically display the current DMX value for any channel that is currently being adjusted The display will automatically detail the changing DMX values as they are received from the controller This function is off by default FLIP This function will flip the display readout by a 180 allowing for better visualization when the fixture is mounted in an inverted position D ON The display is designed to turn off during normal operation to avoid excessive light in situations that require an extremely dark environment This function will adjust the time delay the fixture will remain on before it turns off This function is disabled as default LOCK This function allows you to lock the keys With this function you can activate the automatic keylock status If this function is activated the keys will be automatically locked in 15 seconds from the last press In OElation Professional Los Angeles Ca 22 www ElationLighting com ELAR 162 TRI PAR order to deactivate the keylock status press the Mode Esc button for 3 seconds 1 Access the main menu Tap the UP button until DISP is displayed Press ENTER the display will show VALU Tap the UP button until is displayed and tap the ENTER button Pres
38. traits The DMX address is set electronically using the controls on the LED menu Cable Requirements This fixture is designed with special cables for both DMX and power These cables are specifically designed to maintain the integrity of the IP rating When using this fixture outdoors be sure to ONLY use the Elation cables that have been manufactured to meet the IP rating First DMX Cables Special DMX First cables may be purchased from Elation to provide a means of data communication with standard DMX fixtures for indoor use These cables will come with the IP rated twist lock connector on one end and either a 3 pin XLR male or female connector on the other depending on model Be sure to only use these cables for intergrading this fixture in a standard DMX chain Elation Professional Los Angeles Ca 15 www ElationLighting com ELAR 162 TRI PAR First Power Cable A special power First cable is included with every fixture This cables is used to provide power to your fixture This cable comes with the IP rated twist lock connector on one end and a standard Edison 3 prong grounded prong on the other end Be sure to only use this cable for power distribution and never attempt to connect this cable to the DMX lines You can chain multiple fixtures together through serial linking Using the IP rated signal cables provided through Elation Always be sure to daisy chain your in and out data connections never split
39. y measure to prevent accidental damage in the event of a clamp failure See the image below Clamp Mounting The ELAR 162 TRI PAR provides a unique mounting bracket assembly that allows the unit to stand on a flat surface or to be hung on truss via a clamp in any safe position see the illustration above Regardless of the mounting option you choose please be sure to refer to the safety guidelines in this manual to avoid damage to the unit and or personal injury OElation Professional Los Angeles Ca 13 www ElationLighting com ELAR 162 TRI PAR When mounting this fixture to truss be sure to secure an appropriately rated clamp to the hanging yoke using a M10 screw fitted through the center hole of the hanging yoke As an added safety measure be sure to attach at least one properly rated safety cable to the fixture See illustrations below Securing the ELAR 162 TRI PAR Always be sure to secure your fixture with a safety cable when suspending the unit from truss or other means The fixture provides a built in rigging point for a safety cable as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to the hanging bracket OElation Professional Los Angeles Ca 14 www ElationLighting com ELAR 162 TRI PAR 7 UNDERSTANDING DMX DMX 512 DMX is sh
Download Pdf Manuals
Related Search