PDF user`s guide
Contents
1. 8486 SELECTION OF WATERING PROGRAMME Press any button once to light up the display Press the M button once or repeatedly e g 5 times until the required value is displayed in field D e g 5 min Set the watering frequency interval of time between successive watering cycles by pressing the F button repeatedly until the required value is displayed in field E e g 24h The selectable intervals are every 8 12 or 24 hours or every 2 3 4 5 or 7 days i MANUAL START MANUAL START MANUAL START 3s0c 3s0c 3 s0c ETRE QO OO OO IX FREQUENCY IX FREQUENCY OFF 8 hours 12 hours 4 24 hours 5 2 days s 5 days jays For Tempo Select cod 8486 Habes Tempo Select User manual Immediate start Within 10 seconds of selecting the programme press the START button once only Releasing the button the message 0 h blinks 3 times in the display and the automatic watering cycle will start immediately The symbol appears in display field C indica ting that watering is in progress together with the time remaining until the end of the cycle At the end of the watering cycle display field C showsthe X symbol together with time remaining until the start of the next watering cycle 2 9 Watering in progress Time until next watering MANUAL START MANUAL START b m a te X ct xX ON OFF ON OFF x FREQUENCY MINUTES wy x FREQUENCY OFF 8 hours OFF 8 hours 12 hours 12 hour2. three seconds For Tempo Select cod 8486 RESET The factory settings of the timer can be restored at any given moment by pressing the MANUAL and START buttons simultaneously and holding them for at least 10 seconds SWITCHING OFF THE TIMER If the timer needs to be switched off for example to store it away during winter press the F button once or repeatedly until the OFF symbol appears then press the START button For Tempo Select cod 8486 Habbers Tempo Select User manual Pag 5 Rain sensor The timer can be connected to a Rain Sensor by wire or by radio When the level of water in the Rain Sensor rises above 5 mm the watering program will be suspended automatically then resumed once the rainwater in the cup has evapo rated Installation Remove the protective jumper from the rain sensor contacts no tools are needed If the Rain Sensor is not going to be used the jumper must remain in place across the contacts Wired Rain Sensor Fit the connector of the sensor lead Check that the two core cable enters the timer by way of the slot provided in the rear of the housing cod 8480 For Tempo Select cod 8486 Habbers Tempo Select User manual PROTECTION IN WINTER At the end of the watering season and before winter disconnect the timer from the tap remove the batteries and store the device indoors protected from frost and damp This will ensure that the timer remains as good as new f
3. Hades Tempo Select User manual Pag 1 CLEANING THE FILTER The timer is protected by a wire mesh filter that ensures long lasting and trouble free operation The filter should be inspected periodically and washed at the beginning of every season Simply remove the filter from the connector and rinse clean under running water Washing at start of season For Tempo Select cod 8486 FITTING REPLACING THE BATTERIES To fit or replace the batteries press the locking tab fully in to release the front part of the timer which can then be detached Fit 2 new batteries in the holder observing the correct polarity As long as the batteries are replaced within 2 minutes the current settings will remain stored Refit the front part of the timer to the back and press ensuring that the locking tab clicks into place Important always replace the batteries at the beginning of each season NEW 1 5V AA Alkaline For Tempo Select cod 8486 Hades Tempo Select User manual INSTALLATION Fit the timer to a cold water tap following these simple instructions The spout of the tap should have a 3 4 male thread if not use an adapter Screw the clamp collar of the 3 4 female fitting onto the tap Cau tion tighten the collar using hand pressure only Do not use wrenches or other tools Connect the watering line to the quick click or threaded fitting using the appropriate connector Remember to turn on the water tap For Tempo Select cod
4. or many springs and summers to come For Tempo Select cod 8486 For more information and further details please consult the instruction manual supplied with the product
5. s 24 hours 24 hours 2 days 2 days 3 days 3 days ae 10 8 ee eee 10 8 moar For Tempo Select cod 8486 Delayed start Within 10 seconds of selecting the programme press the START button repeatedly until display field C shows the delay between 1 and 23 hours before the start of the automatic watering cycle e g 6 hours Release the button and the number of hours will blink 3 times after which the programme begins the countdown to the auto matic start of the watering cycle shown in display field C above the X symbol Making changes to the watering programme Repeat the programming procedure as indicated in the selection of watering programme section e g changing 5 to 10 The new programme will replace the previous one MANUAL START 3sec imh x MINUTES 3 FREQUENCY OFF 8 hours 12 hours 24 hours N OFF 2 days 3 days ae days For Tempo Select cod 8486 Habes Tempo Select User manual MANUAL WATERING Press the MANUAL button and hold it for at least 3 seconds the unit goes into manual mode with the valve off OFF blinking Pressing the START button the line will be activated for 5 minutes which cannot be changed by the user confirmed by the symbol To stop watering before 5 minutes have elapsed press the START button a second time To quit the manual function make certain that the valve is OFF then press the MANUAL button and hold it for at least
Download Pdf Manuals
Related Search