User`s Manual
Contents
1. matic SCHULZE Users Manual Mug O TECHNICAL DATA An automatic mug press for cups with two flexible jaws which create absolute equal pressure The device will open Pi Son ene cone 23 x 28 x 33 cm automatically when the press procedure is completed and Weight 13 kg lift the finished cup upwards out of the heating sleeve s Vollage 230VAC heating zone The euro patented opening mechanism PONG oera aos posed ses ence es 330 W makes sure that working is now a lot more comfortable FUSE coda rea emas gu Gee eee es 6A Max temperature 210 C Temperature range 50 210 C Heating sleeve 105 x 230 mm Max press surface 85 x 190 mm Diameter of cups 78 85 mm Optional Correction sleeve for cups 72 mm Heating sleeve for beer jugs 95 mm Lifting gear Flexible jaws Hating sleeve s n Y _ k YT k N J Pressure Adjustment an Opening for trouble free replacement of the heating sleeve i i Main switch Fuse 6A Lever to close the press Power supply line 230VAC Display Mug O matic Before you switch on the device please check if your socket is in proper condition and if the grounding wire is connected properly Afterwards you have to read this USER s MANUAL carefully SWITCH ON The green toggle switch activates the press The pilot2. lamp in the switch is shining The display shows the current temperature of the heating sleeve and the red LED 1 Is shining The heating sleeve will heat immediately until the indicated initial temperature is reached PRESSURE ADJUSTMENT You can change the pressure strength with the little knob on the left clamping jaw Make sure the press is open when regulating the pressure Since you cannot read off the pressure you will have to regulate manually in the first place Afterwards you do a hardproof test and if necessary change the pressure accordingly Never close the press without a cup This may lead to overheating of the heating element ATTENTION After each change you should close the press with a cup to check the new pressure setting Damages due to excess pressure settings are excluded from the guarantee And therefore we assume no liability for heating sleeves which have been damaged due to excess pressure MAINTENANCE All maintenance works should be done when the device is switched off You have to pull the plug out of the socket beforehand CLEANING The device should be cleaned with a soft cloth Use domestic dish washing liquid or window cleaning liquid Scrubbing sponges solvents or petrol are not recommended Replacement of heating sleeve The press has to be cold Use the main switch to turn off the device and pull the plug out of the socket Open the plate at the ba
3. atic O Base paint lubrication etc o Heat and base platens symmetry silicone teflon o Hours of work at 220 o Electrical connection grounding wire power cable o Testwith transfer foil o Electronics max temperature 220 C inspection of all functions O Warning stickers o Hours of work at 180 C O Packaging o Temperature tolerance at 180 C C Serial number EC declaration of conformity According to the EC directive 89 37 EC The Walter Schulze GmbH Schmalenbachsitr 15 12057 Berlin hereby declares as European agent for the manufacturer Romanik that the following described machine heat press serialnumber accords to the terms of the following EC directives Machine directive 89 37 Low voltage directive 72 23 EMV directive 89 336 Used standards and technical specifications EN 292 1 EN 292 2 safety of machines EN 60204 1 electrical equipment of machines Berlin Peter Meidinger CEO
4. ck to replace the heating sleeve Pull out the little jack Push the sleeve out of the holder and carelully pull out the connection cable Take the new heating sleeve and caretully insert the connection cable into the duct Then you have to clamp the new heating sleeve into the holder Connect the jack and close the opening at the back of the device Check if the sleeve is working properly Mug O matic Ws press may nb oat by vaino Sat ater reing he users manual Settings DIGITAL THERMOREGULATOR Push the confirmation button for 5 seconds until LED1 is blinking 2 LED1 is blinking and the display shows the preset initial temperature Programming mode has been switched on 3 Use buttons or to set new initial temperature 4 Push the confirmation button The display shows the preset press temperature Use buttons or to set new press temperature Confirmation LED 1 4 Push the confirmation button The display shows the preset time Use buttons or to set new time 5 Push confirmation button to deactivate programming mode The press will apply the new settings The settings will even be saved when the press is switched off Checking of adjusted settings The initial temperature of the heating sleeve is shown on the display press is open DIGITAL THERMOREGULATOR Push button or to check press temperature The display will show the currently adjusted press temperature Push the button to ch
5. eck the adjusted time The display will show the currently adjusted time setting Example for sublimation initial temperature 110 C press temperature 180 C time 240 sek Confirmation LED 1 How to insert cup 2 3 Put the cup with the transfer onto Put the cup in the middle of the sleeve Release the lever The press will open the lifting gear and push it down before you close the press automatically when the press procedure is completed A J s Bulyeay EzOmazIB elA d 9 8 lt 5uc2upuuzi H ju uu Bune u eyjezig 00L Ld Ju uu zi H uid y yU luluu AuseZ9 ZEMUOS _ N l p91 AUOMI9Z0 104 x v9 joubew o1o j x x yor q Ausez0 ZIEMYUOS lt n u ewoy213 pa4 AUOMI9Z0 OY ka L OLS OVA0ES lonjq yseiqelu ne g III 94 AUOMJ9Z9 1OY I uwoJjq Anozeq uneJg SHUM ATeIG SSIOM OGAS OVWAOE paiHbjunIg yoejq ziemyos e e e lluW I eIQ SSI A l vozo lB onen O 6ny YHOLVINDAYOWYSHL IWLIDIG V9 aesnjy Bunieysis Id HUA SSI A ed pes awl LS AZINHDS wei6eIp e91115 OI LVIN3HO9S youms urew Aumg 6 yluzOp AA eyeyos dney OLS OILIOLU O Bn N3JZO9VTOd NVIdLIVHOS GA ZI yun Ajddns semod zoe IseZ 19 Z ON TESTING REPORT CE XXL XXLs XXLsx pic Air press Swing S Swing digi cap Mug O m
Download Pdf Manuals
Related Search