User manual for 01 BeSafe iZi Kid X2 i-size-GB
Contents
1. The cover of the head rest can be taken off separately by disconnecting the hooks at the back and pulling off the fabric towards the front Refit the cover Pull the head rest in the highest position Replace the head rest cover and reconnect the hooks at the back side Pull the harness straps through the holes Connect the loose lower part of the head rest fabric with the plastic part below the head rest Refit the top part and then the shoulder parts Refit the seat part and bring the seat cover under the rear parts of the sidewalls D Warning potential misuse The child seat MUST NOT be installed in a front passenger seat WITH AN ACTIVATED AIRBAG The floor support must always be used Make sure that the floor support is fully pushed down DO NOT use the seat without tightening the front brace Make sure the indicators are green before you drive Guarantee Should this product prove faulty within 24 months of purchase due to materials or manufacturing fault except covers and harness straps please return it to the original place of purchase The guarantee is only valid when you use your seat appropriately and with care Please contact your retailer they will decide if the seat will be returned to the manufacturer for repair Replacement or return cannot be claimed The guarantee is not extended through repair The guarantee expires when there is no receipt when defects are caused by incorrect and improper2. hugger and baby cushion extra available accessory are used Remove the baby cushion extra available accessory when the child is older than I year Remove the body hugger when the child is older than 2 years When the child weighs over 18 kg or the shoulder height grows above the highest position of the shoulder straps the child must change to a seat suitable for children with a weight above 18 kg After an accident the seat must be replaced Although it may look undamaged if you were to have another accident the seat may not be able to protect your child as well as it should Prevent the seat from becoming trapped or weighed down by luggage seats and or slamming doors Before every use make sure the harness is not damaged or twisted Make sure you can fit no more than one finger between the harness and your baby 1 cm DO NOT attempt to dismantle modify or add any part to the seat Warranty will be void if non original parts or accessories are used Never leave your child unattended in the seat Make sure all passengers are informed about how to release your child in case of emergency Make sure luggage or other objects are properly secured Unsecured luggage may cause severe injuries to children and adults in case of accidents Never use the seat without the cover The cover is a safety feature and may only be replaced by an original BeSafe cover Do not use any aggressive cleaning products these may ha
3. isofix arms totally slided out without pushing the seat towards the backrest and tension the frontbrace outwards with the rachet 29 Make sure the floor support is fully pushed down in contact with the floor of the vehicle and locked 30 Make sure that all indicators on both sides are green 31 The seat is delivered with removable SIP side impact protection This extra side impact protection should be used on the doorside of the vehicle It can be connected by slotting between the seatshell and the fabric The seat already offers high level integrated side impact protection This extra side impact protection improves the protection in the side impact still further Not on all models 18 Do not use the SIP on the seat when the space between seat and door of the vehicle is too small which might lead to a situation were the seat is not positioned correctly on the vehicle seat Removing the seat 1 If the seat is installed in the back seat of the vehicle push the front seat of the vehicle forward as much as possible 2 Move the front brace inwards with the ratchet 19 3 Release the ISOfix connectors by pressing the release mechanism on the ISOfix connectors 20 4 Push the switch on each side and push the ISOfix connectors into the base 21 5 Pull the seat back towards the front Turn the seat so you can easily remove the seat 6 Remove the insertion clips from the vehicle Place them under the base of the chi
4. use when defects are caused by abuse misuse or negligence SCANDINAVIAN SAFETY HTS BeSafe as N 3535 Krgderen Norway www besafe com N2000991 2015 10 30
5. 5 SCANDINAVIAN SAFETY e l Stature height 61 105 cm is Max weight 18 kg bq Age 6m 4y USER MANUAL a Rearfacing Thank you for choosing BeSafe iZi Kid i Size It is important that you read this user manual BEFORE installing your seat Incorrect installation could endanger your child Vital information Itis NOT ALLOWED to mount the seat in a front passenger seat WITH AN ACTIVATED AIRBAG ax iZi Kid i Size can only be installed rearfacing with the ISOfix anchorage in a car equipped with ISOfix anchorage points iZi Kid i Size is approved for children with a stature height from 61 to 105 cm rearfacing with a max weight up to 18 kg Read the car list to find out whether your car model is approved to use the seat The harness straps must always be locked when the child is in the seat The harness straps must be tightened without slack and not twisted The shoulder pads contain magnets Magnets can influence electronic equipment such as pacemakers The floor support must always be used Make sure that the floor support is fully pushed down until it touches the floor of the vehicle in front of the seat and that the indicators on the floor support are always showing green We recommend that this seat is used only for children who can sit upright so not younger than 6 months For children under 1 year and or under 10 kg weight we recommend that the most reclined sitting position and the body
6. k rest 17 Click the ISOfix connectors in the ISOfix anchorage of the vehicle 11 18 Remove the installation clips 19 Make sure that all indicators on both sides are green 12 20 Push the seat towards the backrest of vehicle seat till the frontbrace touches the backrest the isofix arms slide in and will click into a new position 13 21 Move the front brace outwards with the ratchet Continue tightening until the brace is pressed well into the back rest of the vehicle seat 14 22 Remove the cap around the floor support An alarm sound will start and stop when the seat is installed correctly with the floor support in contact with the floor of the vehicle seat 15 23 Adjust the floor support so it is in contact with the floor of the vehicle 16 24 The height indicator of the floor support shows green when the floor support is in contact with the floor 17 25 The alarm sound stops when the floor support shows green and is in contact with the floor 26 Positioned in the back seat of the vehicle you should if possible push the front seat of the vehicle backwards so that it is in contact with the child seat If it is not possible to obtain contact with the child seat push the back rest of the front seat of the vehicle forward as far as possible 27 When the child has a stature height of 87 cm or more use the seat in the upright position 28 When you want to enlarge the available space for your child keep the
7. ld seat To remove the front brace from the metal tube move the front brace outwards with the rachet until the lock button of the front brace appears Push the lock button down with a small screw driver while pulling the front brace out 22 N Positioning of the child 1 Check that the shoulder strap slots are level with your child s shoulders 23 2 The height of the shoulder straps and the head rest can be adjusted by pulling the release handle upwards at the back of the head rest and pulling the head rest up or down while keeping the head rest upright 24 3 Pull the shoulder straps up while pressing the button of the central adjuster 25 4 Open the harness buckle 26 5 Position the shoulder straps over the orange marking at sides of the seat to keep the harness open while you position the child 27 6 When the child is positioned place the shoulder straps over the child s shoulders and close the buckle CLICK 28 Pull the harness strap through the central adjuster in the direction of the arrow straight up forwards Continue pulling until the harness is a comfortable but firm fit 29 N Sleeping position The seat has 3 positions By pulling the recline lever upwards the seat can be adjusted into another position 30 Removing and refitting the cover Do take care when you remove the cover as re fitting the cover is done in reverse Start taking off the lower seat part 31
8. nchorage points 3 When mounting in the back seat of the vehicle push the front seat of the vehicle forward as much as possible 4 When mounting in the front seat of the vehicle adjust the back rest into an upright position 5 Positioned in the front seat of the vehicle you should position the seat against the dashboard 6 If it s not possible to position the seat against the dashboard position the seat as far as possible from the dashboard 7 Find the ISOfix anchorage points in the vehicle 4 8 If your vehicle is not equipped with ISOfix insertion clips insert these to make installation easier 5 9 ISOfix insertion clips are underneath the base 10 Install the front brace by sliding the two pins into the oval tube under the front side of the seat Move the front brace inwards with the ratchet The ratchet is used to adjust the front brace in both directions Slide the switch on the ratchet up or down to change direction 6 11 Pull both ISOfix connectors as far out as possible by pushing the grey buttons on top of the base 7 12 Remove the caps from the ISOfix connectors by pressing down the ISOfix release buttons 8 13 Click the installation clips on the ISOfix connectors 9 14 Fold down the floor support before you install the seat in your vehicle 10 15 Place the seat sideways into the car with the front brace towards you 16 Turn the seat into the right position with the front brace against the bac
9. rm the construction material of the seat BeSafe advises that child seats should not be bought or sold second hand KEEP this user manual for later use with the seat DO NOT use the seat for longer than 7 years Due to ageing the quality of the material may change When the child seat is mounted in the car check all the areas where the child seat might touch the interior We recommend using a BeSafe protection cover in these places to avoid cuts marks or discolouration to the interior of the vehicle especially in vehicles with leather or wooden interiors If in doubt consult either the car seat manufacturer or the retailer Preparing to install Adjustable head rest la Shoulder straps 2x 1b Harness buckle 10 Body hugger 1d Front brace le Central adjuster Cif Reclining lever 19 Ratchet for front brace h Cap ISOfix connector 2x li Switch for ISOfix connectors 2x 1j Floor support Ik Height adjuster floor support al Floor support height indicator 1m Release handle head rest 2a Floor support position indicator 2b ISOfix car anchorage 2x 3a ISOfix insertion clips 2x bottom side 3b ISOfix connectors 2X 30 ISOfix indicators 2x 3d ISOfix release button 2x 3e Rearfacing ISOfix installation 1 It is NOT ALLOWED to mount the seat in a front passenger seat WITH AN ACTIVATED AIRBAG 2 The seat can only be installed rearfacing in vehicles equipped with ISOfix a
Download Pdf Manuals
Related Search