M-CST-SR5 User Manual
Contents
1. 3 1 Power on Continuously press at least 2 seconds to power on off the CCTV Tester When the CCTV Tester is powered on press MODE key the main menu will pop up PTZ controller Colorbar generator Cable tester Data monitor Device setting NO video input Address search 3 2 Menu amp Functions Press MODE key continuously or press the Sei key to select the function PTZ controller Video settings Colorbar generator LAN cable tester Data monitors Device setting and enter corresponding function setting sub menu Press SET key to set the parameters in function sub menu Note When the CCTV Tester is powered on it will return to the function which is being operated before it 1s turned off PTZ controller 1 PTZ controller Display the input video images Pan tilt the P T unit and zoom in out the image Setup the controlling parameters like protocol communication port baud rate PTZ ID pan tilt speed set and call preset position RS485 2400 1 Pan Speed 40 Tilt Speed 40 Set PS 8 Go PS 8 Page 10 CCTV Tester User s Manual TE 2 Video setting Adjust the LCD brightness Contrast Color saturation Contrast Saturation Video Format and Video level testing Colorbar generator 3 Colorbar generator Output or receive seven different forms of video color bar to tester monitor cable or other equipment Cable tester 4 Cable tester Test LAN cable or telephone cable Re2. presse button to quit from the address scanning function menu 3 10 Digital Multimeter Colorbar generator Cable tester Data monitor Device setting DUAA 2 Address search 4 gt Function AW Range 1 Function Button DE CLOSE Auto range Data hold Relative measuring p G Function select SALES Manual range 2 SYMBOLS U DC Voltage Measuring U AC Voltage Measuring A DC Current Measuring A AC Current Measuring Q Resistance Measuring d Continuity Testing Y Diode Testing F Capacitance Measuring Page 19 CCTV Tester User s Manual 3 OPERATING INSTRUCTION A DC Voltage Measuring WARNING You can t input the voltage which more than 660V DC it s possible to show higher voltage but it s may destroy the inner circuit Pay attention not to get an electric shock when measuring high voltage a Connect the black test lead to the COM jack and the red test lead to the V jack lt b Press p E to select U enter the DC voltage measurement Auto range by press key and Manual range by press ARAS Manual range 0 000V gt 6 6V range 00 00V gt 66V range 000 0V gt 660V range 000 OmV gt 660mV range c Connect test leads across the source or load under measurement d You can get reading from LCD The polarity of the red lead connection will be indicated along with the voltage value NOTE 9 When only the figure OL is displayed it indicates over ran
3. 000 0mA gt 660mA range 00 00A gt 10A range use 10A socket c Connect test leads in series with the load under measurement d You can get reading from LCD NOTE 9 When only the figure OL is displayed it indicates overrange situation and the higher range has to be selected 0 When the value scale to be measured is unknown beforehand set the range selector at the highest position 0 The maximum current of mA socket is 660mA over current will destroy the fuse and will damage the meter 0 The maximum current of 10A socket is 10A over current will destroy the meter and will damage the operator E Resistance Measuring WARNING When measuring in circuit resistance be sure the circuit under test has all power removed and that all capacitors have discharged fully a Connect the black test lead to the COM jack and the red test lead to theQ jack dl b Press p G to select enter theQ measurement Auto range by press key and Manual range by press SALES Manual range connect the red lead to black leads will display the measure range 000 00 gt 6600 range 0 000 KO gt 6KQ range 00 00 KO gt 66KQ range Page 23 CCTV Tester User s Manual 0000KQ gt 660KQ range 0 000MQ gt 6MQ range 00 00 MO gt 66MQ range c Connect test leads across the resistance under measurement d You can get reading from LCD NOTE When only the figure OL is displayed it indicates overrange situation a
4. Consumption Energy saving technology General Working 10 C 50 C Temperature Working Humidity 30 90 Dimension Weight 176mmx94mmx36mm 980g 6 2 Multimeter specifications Counts 6600 6600 Conversion rate 3 times s Current modes for clamp meter with ZERO function DC Voltage 100mV AC Voltage 660mV Manual y A 1 5 6 ES 0 8 6 10mV 660V 100mV DC Current 6 6mA 66mA 0 5 3 10uA 660mA 100uA Page 28 CCTV Tester User s Manual Tester User s Manual AC Current 660mA 100uA Resistance 6 6KQ 66KQ 0 8 2 660KQ 6 6MQ 66MQ 1 2 5 10KQ Continuity Built in buzzer will sound if resistance is lower than 50 Q Diode ca Display read approximate forward voltage ofdiode Capacitance Page 29 CCTV Tester User s Manual Tester User s Manual 660nF ae 3 5 8 6 6uF 660uF 100nF Page 30
5. User s Manual 6 Specifications 6 1 General Specifications MODEL CCTV Security Tester Video Test Signal mode NTSC PAL Auto adapt Display 3 5 inch digital TFT LCD 960 x 240 resolution LCD adjustment Brightness Contrast Saturation adjustable Video IN OUT 1 channel BNC Input amp 1 channel Output Video Output Mode 1 0 Vp p Video Level test Level test Video signals measured in IRE or mV PTZ controller Communication RS232 RS422 simplex and RS485 Compatible with more than 20 protocols such as PELCO D P Samsung PTZ Protocol Panasonic Lilin Yaan etc Baud Rate 150 300 600 1200 2400 4800 9600 19200bps Video Signal Generation Output one channel PAL NTSC colorbar video signal for testing Color bar generation E monitor or video cable Digital multimeter Multimeter voltage SE EHS and capacitance measuring continuity testing diode testing UTP CABLE TEST Test UTP cable connection status and display in the screen Read UTP cable test the number of the test box DC12V 1A power output DC12V power output Output DC12V1A power for camera Audio input test Audio input test test the pickup and other audio equipments on the front end RS485 data analyst Data Monitor Captures and analyzes the command data from controlling device POWER Power Adapter DCSV 2A Battery Built in 3 7V Lithium polymer battery 3000mAh Rechargeable After charging 3 4 hour working time lasts 12 hours Page 27 CCTV Tester User s Manual Low
6. a The Video In interface of the CCTV Tester and the output interface of camera b Data A of the CCTV Tester and A of the PTZ camera or controlling device data B of the instrument and B of the PTZ camera or controlling device Note Don t connect communications interface with a circuit the voltage higher than 6V Y as a A y aj L O Le d i Ops 9 Se gt Op d S am Page 12 CCTV Tester User s Manual PTZ controll a Press SET key to enter the sub menu of PTZ controller ad b Press the La or key to select the parameter Port Baud which we want to change the value Address Pan speed Press ENTER k he ch RETURN TiltSpeed c Press ey to save the change or press Set PS Get PS key to give up the change d Press SET key to exit the sub menu e Press POWER key to full screen the image A Protocol Select the protocol according to the protocol of the PTZ camera Up to 21 popular protocols are available like elco P Pelco D Samsung Yaan LiLin CSR600 etc B Port Select the communication port for the PTZ camera controlling RS232 422 485 C Baud Select the baudrate according to baudrate of the PTZ camera 150 300 19200bps D Address Set the ID according the ID of PTZ camera 0 254 E Pan Speed Set the pan speed of PTZ camera 0 63 F TiltSpeed Set the tilt speed of PTZ camera 0 63 G Set PS Setup preset position 0 128 a P T Z the camera to desired position b Press SET key
7. LAY SETUP 1 Display configuration 2 CAMERA SETUP 2 Set camera parameters 3 CONTROL SETUP 3 Set PTZ controlling 4 CAMERA MASK SET 4 Set privacy mask 5 PROGRAM 5 Set auto running functions 6 PAL CAMERA 6 PAL NTSC Switch 7 CAM DEFAULT SET 7 Restore the default settings 8 DOME RESET 8 Reset the dome 9 EXIT 9 Exit the main menu B 8 Operate auto running functions by calling preset position effective for some brands of PTZ camera Call preset 33 Open Auto flip function Call preset 34 Reset zero point of PTZ camera Call preset 64 Enter the main menu of the PTZ camera Call preset 95 Enter the main menu of the PTZ camera or stop the PATTERN recording Call preset 96 Run pattern 1 Call preset 97 Run preset tour 1 Call preset 98 Run frame Scan Page 14 3 4 CCTV Tester User s Manual Call preset 99 Run Auto scan Go PS 4 Run Frame scanning Call the preset 098 point 098 Run Auto scanning Go PS A 099 Call the preset point 099 Video Setting User can customize the brightness contrast and saturation of the LCD according to the using environment the CCTV tester auto display the format PAL NTSC of video input and analysis the input video signal level Contrast Saturation a Press the E or key to select the parameter which we want to change the value b Press the or gt key to change the value Press ENTER key to save the change or press RETUR key to give up the chan
8. LE zoom in the image Digital multimeter Page 7 CCTV Tester User s Manual 2 4 Side view 1831 3718V9 din 28 Right Side ZA O 0 we voeo ov Left Side 2 2 2 2 E 2 3 4 5 7 8 9 30 Page 8 CCTV Tester User s Manual 2 5 Installing the Battery The tester has built in lithium ion polymer rechargeable battery The battery cable inside battery cabin should be disconnected for safety during transportation gt S Prior to the use of the instrument the battery cables inside the battery cabin should be well connected gt Usually it need not to disconnect the cable at the normal use pressing key continuously can power on or off the tester 5 y At the first time of use the batteries should be completely exhausted and then i recharged for 4 or 5 hours y The Charge Indicator lights red when charging the battery The charge indicator turns off automatically when the charging is completed A Notice When the Charge Indicator turns off the battery is approximately 90 charged The charging time can be extended for about 1 hour and the charging time within 8 hours will not damage the battery A The tester can work as usual while it is being charged however But the charging time will be extended Press the RESET key at the right of the instrument to restore the default settings when the instrument works abnormally Page 9 CCTV Tester User s Manual 3 Operation
9. USER S MANUAL CCTV Tester PTZ controller ideo Setting Colorbar generater Cable tester Data monitor Device setting Address search CCTV Tester User s Manual Thank you for purchasing the CCTV security tester Please read the manual before using the CCTV Tester and use properly For using the CCTV Tester safely please first read the Safety Information carefully in the manual The manual should be kept well in case of reference Keep the S N label for after sale service within warranty period Product without S N label will be charged for repair service If there is any question or problem while using the CCTV Tester or damages occurred on the product please contact our technical Department Page 1 CCTV Tester User s Manual Table of Content 1 Safety Information a a a nnn nnn nnn nc 3 2 INtrOOUC TOA sss ennen e Seemee dennen Ie ARES 4 el POS iO eea EE 4 22 GOTV Tester KIIS ratas ER AAA 5 29 Front Paneles EE 6 SE EE EE 8 2 90 IMNSTallig Eege 9 Weien Klee 10 CNR e Lull E 10 3 2 Men amp FUNCHON S2sss222 2822255 esececessaces A A A A ARE READ 10 33 FTZ uge 12 EE ENEE EES 15 Reese De 15 3 0 Cable Eege 16 OF Dala en te 17 deo DEVICE SBM Gassen nennen ERR en te eee chee ES 17 3 9 Address EE 18 9 10 Digital SHEET 19 DEL Power GHEET SES 26 SD Audio INDULLES ee 26 6 Specifications sto RA dede Gehangene nonsens asten 27 6 1 General SpeciGAHONS rna ton
10. dress scanning search up the ID of PTZ camera Page 4 CCTV Tester User s Manual B Lithium Ion Polymer Battery 3 7V DC3000mAh The device employs advanced power control and protection circuit The device is high power efficient energy saving and environmental protection It can last 12 hours for normal use after charging for 4 hours 2 2 CCTV Tester Kits Professional design light and portability video display and data control are deliberately integrated which makes the instrument so simple practicable easy for use that the training is almost unnecessary for an operator to be skillful 1 CCTV Tester 3 LAN Cable Tester 5 BNC Cable 6 Safety cord 7 RS485 data cable 2 Power Supply 5V 2A 4 Lithium Ion Polymer Battery 8 Instruction Manual 2 3 Front Panel Page 5 CCTV Tester User s Manual Gi S a O Ca G gt Ct D L aPTZ controller 0000 e 5 Video Setting Colorbar generator Cable tester m 6 Data monitor Device stting Address search Digital multimeter kp a KA a 5 z A 9 TH f MODE set rower tt f 8 LS AA l IR 40 48 YH FAR EE a LI au BL 6 d pa A Dr Ui ei ei 46 4 nd The data reception indicator it lights red while the data is being received The data transmission indicator it lights red while the data
11. ge c The Video Format and Video Level will be displayed in the lower portion of the screen If there is no video signal at the Video IN port of the CCTV Tester the type of NTSC or PAL and Video Level will not be displayed Depending on the type of camera connected to the CCTV Tester the Video Format will automatically change between NTSC and PAL and the Video Level will automatically change between IRE Institute of Radio Engineers and mV NTSC signals measured in IRE units PAL signals measured in mV The Video Level should be within the indicated range Levels that are too low will result in a dim picture with reduced dynamic range A Video Level that is too high will result in washed out pictures with decreased The CCTV Tester will display Normal when video levels are Page 15 CCTV Tester User s Manual 1000mV 20 Exceed or Weak will be displayed when video level out of 1000mV 20 3 5 Colorbar generator Output video at any mode Colorbar generator Output or receive seven different forms of video color bar to test monitor video cable or other equipment a Press the E Sei key to select the parameter which we want to change the value DE or key to change the value b Press the L c Press ENTER key to save the change or press RETURN key to give up the change 3 6 Cable Tester Test LAN cable or telephone cable Connect LAN cable or telephone cable with the CCTV Tester a
12. ge situation and the higher range has to be selected 0 When the value scale to be measured is unknown beforehand set the range selector at the highest position Page 20 CCTV Tester User s Manual B AC Voltage Measuring WARNING You can t input the voltage which more than 660V AC it s possible to show higher voltage but it s may destroy the inner circuit Pay attention not to get an electric shock when measuring high voltage a Connect the black test lead to the COM jack and the red test lead to the V jack a e b Press p G to select U enter the AC voltage measurement Auto range by press key and Manual range by press SALES Manual range 0 000V gt 6 6V range 00 00V gt 66V range 000 OV gt 660V range 000 OmV gt 660mV range c Connect test leads across the source or load under measurement d You can get reading from LCD NOTE 9 When only the figure OL is displayed it indicates over range situation and the higher range has to be selected 0 When the value scale to be measured is unknown beforehand set the range selector at the highest position C DC Current Measuring WARNING Shut down the power of the tested circuit then connect the meter with the circuit for measurement a Connect the black test lead to the COM jack and the red test lead to the mA jack for a maximum of 660mA current For a maximum of 10A move the red lead to the 10A jack Page 21 CCTV Te
13. is being transmitted The charge indicator 1t lights red while the battery is being charged As the charging is complete the indicator turns off automatically The display Icon of battery electricity it displays the electric quantity Main menu it shows main functions of CCTV Tester Sub menu Shows and sets the values of functions Page 6 CCTV Tester User s Manual Long pressing it more than 2 seconds to turn on off the tester short pressing to turn on off the PTZ controller menu displaying Menu key it pops up the main menu constant press it or press the ZS or LY key can shift between functions Setup key press it or press left or right key to enter sub menu to set the parameters of functions Upward Select the item which will be set or add the value of the parameter Tilt the PTZ upward Leftward Enter the sub menu or select the parameter whose value will be changed Reduce the value of the parameter Pan the PTZ left Rightward Enter the sub menu or select the parameter whose value will be changed Add the value of the parameter Pan the PTZ right Downward Select the item which will be set or reduce the value of the parameter Tilt the PTZ downward Confirm Open Confirm the setting of parameters open the aperture Return Close Return or cancel while setting parameters of the menu close the aperture Near focus Focus the image nearby Far focus Focus the image faraway TE
14. mote kit ce The connecting condition and the sequence of wires will be displayed as well as the serial number of the cable tester kit Cable Data monitor 5 Data Monitor Port 485 Baud 4800 O en Pe Captures the protocol from the controlling system and display AQ 00 00 00 00 00 OF AO 00 10 00 40 5F S Ap EM ge command data It is helpful to debug and maintain RS485 AO 0 OO 40 00 4B A 00 00 40 E oF communication AO 00 40 00 4D AQ 00 00 OO OF Device setting 6 Device setting EEE Set the parameters of the CCTV Tester Auto power off Prompt sound Language English Keypad tone Language Brightness Address search Brightness 7 Address search off Not saved Enter to apply Page 11 CCTV Tester User s Manual Address search 7 Address search Protocol Port Baud Search the ID of PTZ camera Address Far Near Start search Wid Tele Adjust addr Digital Multimeter 8 Digital Multimeter 0 000 V Digital Multimeter performs AD DC Voltage AC DC Current Resistance Continuity Capacitance and Diode test Auto MuAA Q 4 gt Function Manual Range Data hold Relative measuring A Y Range 3 3 PTZ Controller Display the input video images Pan tilt the P T unit and zoom in out the image Setup the controlling parameters like protocol communication port baud rate PTZ ID pan tilt speed set and call preset position The following connections should be confirmed before use
15. nd cable tester And then the connecting status cable type and the sequence of wires will be displayed as well as the serial number of the cable tester kit Cable tester DD YO WH A able tester Cable tester d mp 4 1 2 2 2 3 3 3 4 4 4 4 5 5 6 6 j 7 bh vi zl oo oo oo Cable Pin to Pin Cable Crossed ethernet gt Other Straight through Line Cross Line Open Line or Short Line Page 16 CCTV Tester User s Manual 3 7 Data monitor Data monitor Capture the command data from RS485 controlling system enke Ennn 00 AF D 40 AF DO 00 AF a Connect the RS485 or RS232 interface of controlling system ri e 00 00 02 40 OO AF 4 with the RS485 or RS232 interface of the CCTV Tester In 00 00 00 00 AF C case of RS485 A to A B to B b Press SET key and then press or key to select communication port according to the system connection Press SET key to save the change d Press or key to select the baud rate according to the baud rate of controlling system and then press SET key to save the change and capture command data from controlling system e Press RETURN key to clear the screen 3 8 Device setting Set the parameters of the CCTV Tester o soune es Language English Brightness 7 Address search off Not saved Enter to apply Auto poweroff Setting the time of auto shut down Disable 5 10 60 Disable Disable the Auto poweroff function 5 means the CCTV will p
16. nd the higher range has to be selected F Continuity Testing WARNING When testing the circuit continuity be sure that the power of the circuit has been shut down and all capacitors have been discharged fully a Connect the black test lead to the COM jack and the red test lead to theQ jack b Press to select d enter the continuity test c Connect test leads across two point of the circuit under testing d If continuity exists i e resistance less than about 500 built in buzzer will sound e You can get reading from LCD NOTE If input open circuit or the circuit resistance measured is higher than 660Q then the figure OL will be display G Diode Testing a Connect the black test lead to the COM jack and the red test lead to the MH jack q b Press p E to select Y enter the diode testing c Connect test leads across to the anode the black lead to the cathode of the diode under testing Page 24 CCTV Tester User s Manual d You can get reading from LCD NOTE The meter will show approximate forward voltage drop of the diode O Ifthe lead connection is reversed only figure OL will be display H Capacitance Measuring WARNING To avoid electric shock be sure the capacitors have been discharged fully before measuring the capacitance of a capacitor a Connect the black test lead to the COM jack and the red test lead to the MH jack wollen lt b Press p G t
17. o select T enter the capacitance measurement Auto range by press key and Manual range by press AGO Manual range 0 000nF 6 6nF range 00 00nF 66nF range 000 0nF 660nF range 00 00uF 66uF range 000 0uF gt gt gt 0 000uF gt 6 6uF range gt gt 660uF range gt 0 000mF 6 6mF range 00 00mF gt 66mF range c Before connect test leads across two sides of the capacitor under measurement be sure that the capacitor has been discharged fully d You can get reading from LCD Page 25 CCTV Tester User s Manual 4 DC12V 1A power output Power the camera with DC12V 1A power output from the tester It is helpful for demo and testing where there is no power supply available V VIDEO IN VIDEO OUT am EE EK Se El DC 12VAA Nt meets OUTPUT weesje o o p vara H Notice a Don t input any power into the DC12 1A OUTPUT port of the CCTV tester to avoid destroy b Don t output this DC12V 1A power to the power input port of the CCTV tester to avoid destroy c When the requirement of the camera is higher than 1A the CCTV tester will enter protection mode Disconnect all the connections of the CCTV tester and then connect the CCTV tester with power adaptor to resume the CCTV tester 5 Audio input test Test the audio input from pickup devices Connect the tester and pickup device with the audio cable PE Page 26 CCTV Tester
18. ower off after 5 minutes when there is no any operation Keypad tone Open or close the beep of pressing keypad Language Select language of OSD menu Brightness Setting the brightness of OSD menu and background 0 7 Address search off on Open or close the PTZ address search Menu a Press or key to move the parameter we want to change b Press J or gt to change the value c Press ENTER to save the change or press RETURN key to give up the change Page 17 CCTV Tester User s Manual 3 9 PTZ address scanning Search up the ID of PTZ camera Note Please isolate the PTZ camera with other PTZ cameras before searching up Otherwise all the PTZ cameras in the same system will pan at the same time Press keys to Device setting menu Prompt sound Language Brightness Address search Not saved Enter to apply ENTER S Press key to confirm after change Address search to on which add address scan sub menu Press to switch the sub menu as illustrated Note The system returns to OFF after shutdown and the Address search Protocol scan sub menu closes automatically Set ON again for next Port Baud use Address Press ser key to set protocol communication port Far Near Start search Wid Tele Adjust addr communication rate make them same as the PTZ camera Press SE key the address values is constantly on the rise or decrease NEAR The tester
19. ster User s Manual q b Press p G to select A enter the DC current measurement Manual range by press SALES only manual range supply Manual range 0 000mA gt 6 6mA range 00 00mA gt 66mA range 000 0mA gt 660mA range 00 00A 10A range use 10A socket c Connect test leads in series with the load under measurement d You can get reading from LCD The polarity of the red lead connection will be indicated along with the voltage value NOTE 9 When only the figure OL is displayed it indicates overrange situation and the higher range has to be selected 0 When the value scale to be measured is unknown beforehand set the range selector at the highest position 0 The maximum current of mA socket is 660mA over current will destroy the fuse and will damage the meter 0 The maximum current of 10A socket is 10A over current will destroy the meter and will damage the operator D AC Current Measuring WARNING Shut down the power of the tested circuit then connect the meter with the circuit for measurement a Connect the black test lead to the COM jack and the red test lead to the mA jack for a maximum of 660mA current For a maximum of 10A move the red lead to the 10A jack q Se b Press p E to select A enter the AC current measurement Manual range by press SEPAN only manual range supply Page 22 CCTV Tester User s Manual Manual range 0 000mA gt 6 6mA range 00 00mA gt 66mA range
20. ta ROA ARPA annette 27 6 2 Multimeter specifications 202222 nn e nnn nnn ennen eenen 28 Page 2 CCTV Tester User s Manual 1 Safety Information Notice B The tester is intended to use in compliance with the local rules of the electrical usage and avoid to apply at the places which are inapplicable for the use of electrics such as hospital gas station etc B To prevent the functional decline or failure the product should not be sprinkled or damped The exposed part of the tester should not be touched by the dust and liquid m During transportation and use it is highly recommended to avoid the violent collision and vibration of the tester lest damaging components and causing failure B Don t leave the tester alone while charging and recharging If the battery is found severely hot the tester should be powered off from the electric source at once The test should not be charged over 8 hours B Don t use the tester where the humidity is high Once the tester is damp power off immediately and move away other cables connected B The tester should not be use in the environment with the flammable gas B Do not disassembly the instrument since no component inside can be repaired by the user If the disassembly is necessary indeed please contact with the technician of our company B The instrument should not be used under the environment with strong electromagnetic interference B Don t touch the
21. tester with wet hands or waterish things B Don t use the detergent to clean and the dry cloth is suggested to use If the dirt is not easy to remove the soft cloth with water or neutral detergent can be used but the cloth should be tweaked sufficiently About digital multimeter B Before using you must select the right input jack function and range B Never exceed the protection limit values indicated in specifications for each range of measurement D When the meter is linked to a measurement circuit do not touch unused terminals Do not measure voltage if the voltage on the terminals exceeds 660V above earth ground B At the manual range when the value scale to be measured is unknown beforehand set the range selector at the highest position B Always be careful when working with voltages above 60V DC or 30V AC keep fingers behind the probe barriers while measuring m Never connect the meter with any voltage source while the function switch is in the current resistance capacitance diode continuity otherwise 1t will damage the meter m Never perform capacitance measurements unless the capacitor to be measured has been discharged fully m Never measure any of resistance capacitance diode or continuity measurements on live circuits Page 3 2 CCTV Tester User s Manual Introduction The CCTV Tester is developed for the On Site installation and maintenance of video monitoring system It can be used for displa
22. to enter PTZ controller submenu c Move the yellow cursor to Set PS and then press or gt key to select the preset position number d Press ENTER key to complete preset position setting or preset RETURN key to give up preset position setting Tips Press or key to accelerate the value changing H Go PS Call the preset position 0 128 The PTZ camera will go to the desired preset position a Move the yellow cursor to Go PS and then press di or gt key to select the preset position number b Press ENTER key to complete preset position calling or preset RETURN key to give up preset position calling Page 13 CCTV Tester User s Manual Tips Press Ee or lt key to accelerate the value changing The way of calling the OSD menu and preset of the PTZ camera may vary with control systems from different manufacturers Please read the operation manual of control system manufacturer for details The way of calling OSD provided for reference is calling preset 64 a Move the yellow cursor to PTZ controller to enter PTZ controller mode b Press SET key to enter PTZ controller sub menu Press A or v key to move the yellow cursor to Go PS C Press lt or gt key to select the preset number 64 and then press ENTER key to call OSD menu of the PTZ controller e Se OSD menu of dome Go PS 4 064 Call the preset point 064 OSD Menu of Dome For reference only MAIN MENU MAIN MENU 1 DISP
23. will search up the ID quickly and continuously from 1 to 256 When the ID is searched the PTZ camera will pan right At this time please press any key to stop searching up FAR The tester will search up the ID quickly and continuously from 256 to 1 When the ID is searched the PTZ camera will pan left At this time please press any key to stop searching up WIDE The tester will search up the ID step by step from 1 to 256 When the ID is searched the PTZ camera will stop panning FAR The tester will search up the ID step by step from 256 to 1 When the ID is searched the PTZ camera will stop panning Page 18 CCTV Tester User s Manual Press button the tester will search up the ID quickly and continuously from 1 to 256 When the ID is searched the PTZ camera will pan right At this time please press any key to stop searching up Press ree manual single step decreasing button the tester will search up the ID step by step from 256 to 1 When the ID is searched the PTZ camera will stop panning Press button the tester will search up the ID quickly and continuously from 256 to 1 When the ID is searched the PTZ camera will pan left At this time please press any key to stop searching up Press manual single step incremental button the tester will search up the ID step by step from 1 to 256 When the ID is searched the PTZ camera will stop panning Press the direction control button to adjust Speed Dome Camera
24. ying video controlling PTZ generating images capturing data of RS485 and testing LAN cable etc Its functions easy operation and portability makes it simple for the CCTV technician to install and maintain CCTV system improving work efficiency and get the labor cost down 2 1 Features 3 5 TFT LCD 960 H x240 CV resolution Video Level testing video signals measured in IRE or mV DC12V 1A power output for camera Audio input testing Digital multimeter voltage current resistance and capacitance can be tested continuity testing diode testing PTZ control Pan tilts the P T unit zooms in out the lens adjusts the focus aperture and sets and calls the preset position Video displaying Automatically adapts and displays the video format of NTSC PAL LCD Brightness Contrast Color Saturation are adjustable Video Generating The PAL NTSC multi system colorbar video generator seven system switchable transmit receive seven system colorful imagines Data analyst Captures and analyzes RS485 controlling data to help the technician to find out the problem Cable testing It is powerful in testing LAN cable measuring the connecting status displaying the sequence of connection and the NO of the LAN cable Multi interface and Multi baud rate Support RS232 RS485 and RS422 interface baud rate ranging from 150 600 to 19200bps Multi protocol Supports more than twenty PTZ protocols For example PELCO P PELCO D SAMSUNG etc PTZ ad
Download Pdf Manuals
Related Search