USER MANUAL - Aybey Elektronik
Contents
1. 03 3 where the driven force in up and down directions is different then the system automatically uses M4 as MK2 This option may be also used in other lift types besides hydraulic A11 USE OF 3rd SPEED 0 3 speed is not used 1 This option is used in variable speed lifts where the car speed exceeds 1m s In this case the lift will have slow fast and high speeds A12 LIFT GROUP NUMBER 0 Simplex the lift works alone 1 Duplex the lift works in a group of lifts The lift with the group number 1 administrates the landing calls 2 Duplex the lift works in a group of lifts The lift with the group number 2 gets landing calls from lift with the group number 1 F 7 5 5 02 04 R 4 16 31 A13 MISSING FLOOR DUPLEX LIFT 0 No level difference of both group lifts 1 The base floor of group 2 is one floor above group 1 2 B P2 AUXILIARY PARAMETERS B01 AFTER DOOR LOCK FAILURE 0 The system continues operation 1 The system is blocked if the number of consequent errors have been repeated as the number stored in the parameter B12 2 All call registers are cleared B02 ERRORS ARE REPORTED ON THE SCREEN 0 When an error occurs the current screen is not left Only when the screen is the main screen then a flashing message about the error is displayed 1 When an error occurs the current screen is left and an error screen is displayed where a2. 2 PEL If the clock time is within the time interval PERIOD1 which is specified in section K8 then the cabin call is allowed otherwise not allowed 3 PE2 If the clock time is within the time interval PERIOD2 which is specified in section K8 then the cabin call is allowed otherwise not allowed 2 D 5 6 PULSE NO OF FLOORS If you select as floor selector in A05 2 incremental encoder or 3 absolute encoder then you can enter this section and edit the pulse data for any floor OO FLR 5 O1 FLR PULSE xxxxxx 202 FLR PULSE xxxxxx 03 FLR PULSE xxxxxx F 7 5 5 02 04 R 4 23 31 In order to select a floor to change its data press ENT key in its line Then you see the following editing screen S02 EREL yi 2023451 You change the data by using 7 4 keys In order to go from column to column use lt and keys D 6 K7 GENERAL PULSE This parameter is used only if A05 is 2 or 3 The parameters given in this section correspond to the distances that are used for all floors When you change any pulse number then the distance for the related path is changed in all floors All of the data given in this section are the distances in encoder pulses to the floor level specified in the previous section MKL STOPPER gt DOOR ZONE ENCODER FLOOR LEVELLING A MK1 STOPPER The distance in pulses between the exact floor level and the point of stop command
3. 01 first telephone number that will called by the modem X02 The second telephone number that will be called by the modem X03 First modem initializing string X04 Second modem initializing string X05 Scheduled time for modem 2 1 5 R5 RESET PULSES ZEE Eds BD S ARE CLEARED ENT Load You must enter this section once before operation if you are using incremental or absolute encoders as floor detector When you see the screen as above then pressing ENT will make all encoder pulse records as 0 2 1 6 R OTHER UTILITIES Do NOT Use This menu is designed for authorized technical persons There is no function for user It may cause undesired results to enter anything to this menu If you enter this menu by mistake you must exit by pushing ESC 7 5 5 02 04 4 29 31 CHAPTER 3 ERROR LOG In SWline Series Control System all determined errors are reported at runtime on main screen and stored in permanent memory Error storing capacity of system is limited by 128 If an error occurs when there are already 128 errors in memory then oldest error is cleaned and the new one is stored You can see the stored last 128 error anytime by using LCD screen or computer connection Here we will see how to see error list reports by using keypad and LCD On main menu enter M3 ERROR LOG sub menu MI VARIABLES M00 M2 PARAMETERS gt M3 ERROR LOG MA4 LANGUAGE LiSAN In a few second you see the foll
4. Stop circuit is closed SD Stop and Door Contact circuits are closed SDL Stop Door Contact and Door Lock circuits are closed 2 Door is opening CAM is active gt lt Door is closing CAM is inactive 13 35 HOUR MINUTE MID ROWS 2 3 Row 2 and 3 shows Call Registers Most left character of Row 2 shows the calls for bottom floor As moving right floor number increases One character is used for each floor The meanings of symbols are explained below Call for this floor Cabin Call for this floor A Up Call for this floor v Down Call for this floor In a floor 1 2 or 3 of these symbols can appear together at the same character except In these rows only defined floor number of characters can be seen BOTTOM ROW Columns 2 3 4 5 This group shows information about car s floor and moving direction 052 Caris exactly at floor 5 Car is exactly at floor level 05 floor 5 Car is between floors 05 Lift has a target on up direction 05 Lift has a target on down direction Columns 8 9 10 This group shows information about car s target and lift s run mode INS Lift is in INSPECTION mode t 1 Lift has no target t03 Lift has a target of Floor 3 F 7 5 5 02 04 R 4 9 31 Columns 12 13 14 15 16 This group shows information about car s motion and speed STOP Car is stopping START Caris stopping but about to move Lift is pr
5. be supported near future The last item in main menu is M5 SERVICES M2 PARAMETERS M00 M3 ERROR LOG M4 LANGUAGE LiSAN pM5 SERVICOBS This is also a shortcut to RA OTHER UTILITIES menu As explained above this menu is only for authorized technical persons There is no function for user It may cause undesired results to enter anything to this menu If you enter this menu by mistake you must exit by pushing ESC F 7 5 5 02 04 R 4 31 31 SWLINE ERROR CODES COD ERROR STOP CIRCUIT IS OPEN DOOR CONT ARE OPEN DOOR LOCKS ARE OPEN BUTTOM LIMIT IS OPEN Down limit signal 817 is cut during down motion Except bottom floor TOP LIMIT IS OPEN Up limit signal 817 is cut during up motion Except top floor At fast speed system could not get new floor data during the period defined at C08 PASS TIME OVERFLOW At slow speed system could not get Stopper MK signal during the period defined at C09 7 o DOOR CANNOT OPEN LOCK WAIT OVERFLOW HIGH LIMITS ARE OPEN Both Up and Down high speed limits 817 and 818 are open ERROR IN FLOOR INFO SECURITY CIR IS OPEN ERROR IN FLOOR NO UP ERROR IN FLOOR NO DN EL PARASIT IN INPUTS There are electrical parasits at some input s Input s are not stable PARK FLR DEF IS WRONG Defined park floor B04 is bigger than maximum number of stops A01 FIRE FLR DEF IS WRONG Defined fire floor B05 is bigger than maximum number of stops A01 LIFT SYS DEF IS WRONG CABIN CONTROL COMMUN ANDING CONTROL COMM HASE
6. only one door then do not use this section In order to use the data given in this section A08 number of automatic doors in cabin must be 2 QO FLR DOOR Asl YES ELER DOOR A YES OZ FLR DOOR Asi VES DS PLR DOOR Asi YES If the system has two doors then they are named as A and B When you see 1 YES as data then it means that this door will open at this floor When you see 0 NO as data then it means that this door will not open at this floor If your system has two doors in cabin then you can select freely which doors are active in each floor In order to change the condition of the door for a specific floor press ENT key in the line of this floor In the following screen you can change the data by using and keys between 0 NO and 1 YES 03 FLOOR DOOR A Witt JP OPEN 2000001 YES In this screen the data for third floor is displayed as Yes It means that door A will open at third floor Here 0 is for NO and 1 is for YES For door B the same procedure applies for item K3 2 D 3 K4 CABIN CALLS You can set allowance for cabin calls for any floor by using this section If you switch off cabin call of any floor then any call coming from car operating panel will be discarded When you enter this section by pressing ENT key in menu M24 then you see the following screen 00 CABIN CALL 1 ON Od CABIN CALLS 1 02 CABIN CALL 1 ON 2 3 CALL L OEE In order to sele
7. B DOOR ZONE The section in pulses from the exact floor level to the level in which the automatic door can be opened The pulse number given in this parameter applies from the floor level up and down C ENCODER FLOOR The distance in pulses where the controller switches to low speed when it reaches its target floor D LEVELING The limits of releveling zone in pulses The controller activates releveling process between the limits specified by this parameter E MK2 STOPPER The distance in pulses between the exact floor level and the point of stop command when two stoppers are used D 7 K8 CALL REGISTER PERIODS BERLOD 0185251 15524510 gt PERIODZ 16 0 092550 You can specify two periods in this section The first one is used as the time period PE1 and the second is PE2 in sections K5 and K6 where call register allowance is specified Here the data give is any time of the day is 24 hour time system As an example for the screen shown above any hall or cabin call register can be active between from 8 30 am to 6 30pm if it is selected as PER 7 5 5 02 04 R 4 24 31 2 P5 MAINTENANCE TIME You can see or set next maintenance day by using P5 in menu 20 In this section you see current setting of the next maintenance day NEXT MAINTENANCE 01 07 2006 If you press any key in this screen then you will come to the maintenance date editing screen NEXT MAINTENANCE MONTH 2000007 YEAR 2002006 You can
8. any call up down or cabin by using keypad when lift is not in inspection mode Here an example On Main Screen push gt Floor No 000002 In this screen you can change floor no by arrow keys and when you push ENT a cabin call is given On Main Screen you can give up and down call in the same way by pushing L buttons respectively 1 G SOFTWARE VERSION NUMBER To see software version of your system on Main Screen push and hold ESC You see the following screen AYBEY ELEKTRON K LTD SWline series V2 63 Ti 205 HH MM Here V2 63 shows software version of your system You can also see date and time in this screen When you release ESC you turn to Main Screen F 7 5 5 02 04 R 4 14 31 CHAPTER 2 PARAMETERS All information about lift and control system settings and timings are stored in system parameters These parameters are classified into several groups to make it easy for users These groups are e MAIN PRMs These the most important and necessary parameters for lift to function properly Axx e AUX PRMs This group includes secondary parameters for lift and the parameters about control system SWline Series working conditions Bxx TIMINGS These are timing parameters for lift Cxx FLR PARAMET These are the parameters that can have different value for each floor MAINTENANCE This is the date at which system requires maintenance OUTPUT DEF This paramet
9. display press ENT key to go to the input field of the right display You can select the right side display by using or keys as in the previous field After you have chosen the character you want on the right display press ENT key to return back to the previous menu By using the same procedure you can specify all characters for your lift system This section is for changing display data for any floor But if you want to reorganize your displays in an ordered manner then you can use special utilities You can go to this section by following from M20 menu P9 UTILITIES R1 DISPLAY UTIL In this utilities section the following screen is waiting for an input BASE FLOOR N 000000 7 5 5 02 04 R 4 21 31 You can change the data by using T and keys between 0 and maximum floor no If you specify which floor is the entrance floor to the building then this utility sets the digital display of the entrance floor base floor as 0 All floors above this floor are numbered starting 1 and incremented by 1 at every floor All floors below 0 base floor are numbered starting 1 and decremented by 1 at every floor If you have a regular display order in your system but with a few exceptions then first use the utility explained above and then changes the data for exceptional floors one by one 2 D 2 K2 SET DOOR A and K3 SET DOOR B This section is designed for selection of active automatic door s at each floor If the system has
10. e e eR Bee 17 ar e xam w A Qua Ya An Am u 19 2 D P4 FLOOR PARAMETERS etu hack LA 20 DoD DISPLAYS E cest de e belek 21 SET DOORS no uber Dedi cer 22 2 D3 Rd CABIN CALES Goo rne ad cee Daya laaan a Qa el fl 22 2 D 4 Y KS HAL C ALIS oi ops cs yere td cea rh esa ev Parto e i vaa s e EY 23 2 D 5 K6 ENCODER PULSE OF FLOORS 23 2 D 6 K7 GENERAE PULSE trot sa sua TIR Ca EP ayapa Me TO ERSTER RU 24 2 D 7 K8 CALL REGISTER PER ODS eee 24 2 E P5 MAINTENANCE TIME 2i ote tee tite tos NCC Rd eus ane dee 25 2 F P6 OUTPUT DEFINITION lr Sa a Lupo ope aM Ne DD KY cod 25 2 G P7 INPUT DERINDEIONGS pectet tust lee 26 2 H P8 DATE amp TIME ee ite ee ICA 27 Coo feto Rivest tes nel a a Ee A Lc s M Re 28 2 ED RI DISPLAY UTILITY eot ib OE enli nel EROR Pad ned bu be eui neds 28 2 L 2 R2Z FACTORY SETTINGS tere aee ed re In PAREN IE e Qa Pes oe ee eor e RR dee e SERPENT 28 2 EF3y R3 SET PASSWORD cea oye ERE aqya S C EA EVE ER 28 2 2 R4 MODEM SETTINS U irs Errore deine dua FE Henke toe dans FERE Pe UU 29 25155 R5 RBSET PUESBS 2 322 hat onda Seres etae edat ess attesa etie mato tus cades ta gas 29 2
11. enter new maintenance date in this screen When the date exceeds the maintenance date then the lift cannot be moved You can also see MAINT word in the main screen when maintenance date 1s exceeded 2 F 6 DEFINITIONS It is possible to control some output relays with user defined events In order to do this first select P6 in menu M20 You are faced with the following screen SOYLEYEN IE CN Output No 2000000 Output Coce 7000000 In SWline system there are 2 3 programmable output relays S1 and S2 can be freely used in all systems where K2 can be programmed only in systems with one automatic cabin door The summary of these outputs is as follows OUTPUT NO CONTACT TYPE REMARKS 1 51 Always free to program 2 S2 NO Always free to program 3 K2 NO NC If A02 is 1 then free to program If A02 is 2 K2 serves as the door relay for second door First you have to enter the output no from the selections in the first table You have to enter 1 2 or 3 as output channel Then you can choose which function to connect to this channel from the second table below and complete the output definition After the procedure described above the defined output relay will be activated according the event you selected If the state of the lift matches the one you selected the output relay is ON otherwise it is OFF F 7 5 5 02 04 R 4 25 31 Here is the list of events that can be connected
12. 00015 2000015 2000025 gt 2000025 lj 2000024 After setting the parameter if you push the new value screen is saved But if you push ESC changes are cancelled In both cases you turn previous screen and you see value of parameter Here we push ENT and see the following screen gt 01 STOPS 24 A02 COMMAND 4 MO D YEN A04 DOOR TYPE So we have changed number of floor in system as 24 and this change is saved and stored in memory 7 5 5 02 04 R 4 12 31 On this screen let s change another parameter A02 LIFT COMMAND SYSTEM This parameter is in abbreviated form as A02 COMMAND gt 01 STOPS 24 02 4 ASTE T TYPE A04 DOOR TYPE ADT NUM OE STOPS 24 2A02 COMMAND 4 TPE YE A02 LIFT COMMAND on S LEM 2000004 PULL COLLECTIVE A02 LIFT COMMAND SYSTEM 2000003 UP COLLECTIVE A02 LIFT COMMAND ovo RM 2000002 DOWN COLLECTIVE ENT AOI NUMZOr SS TOPs 24 2A02 COMMAND s AOO TYPE A04 DOOR TYPE Setting has been saved In the A02 parameter change screens above you see explanations at bottom row according to the value of parameter You will see this type of explanations in some parameter change screens if changed parameter has a value of a type system shape etc instead of number F 7 5 5 02 04 R 4 13 31 1 F GIVING CALLS BY KEY PAD In SWline Series it is possible to give
13. 5 5 02 04 4 15 31 A04 DOOR TYPE 0 Semi automatic wing landing door no cabin door 1 Semi automatic wing landing door with automatic cabin door 2 Full automatic cabin and landing door A05 FLOOR SELECTOR SYSTEM 0 Gray code based bi stable magnetic switches 1 Counter 2 Incremental Encoder 3 Absolute Encoder A06 PRE OPENING DOORS No Yes A07 HYDRAULIC LEVELING SYSTEM 0 No Releveling 1 Releveling system will be used in hydraulic lift Motor is running 2 Releveling system will be used in hydraulic lift Motor is not running A08 NUMBER OF AUTOMATIC DOORS IN CABIN 1 There is only one cabin door 2 There are two doors in cabin Do your selections of driven doors for each floor in M2 SET PARAMETERS P4 FLR PARAMET K2 and K3 A09 CONTROLLER SHAFT COMMUNICATION 0 Parallel Communication between controller and car and landing panels One to one cable is connected between controller terminals and signals or buttons Call registers are controlled by SWPIs 1 Serial RS 485 communication between controller and car and landing panels No SWPIs are used for call registers and buttons A10 NUMBER OF STOPPERS 0 There is only one floor level stopper MK 1 There are two floor level stoppers MK1 and MK2 When this option is selected then MA terminal serves as MK2 If lift type is selected as hydraulic
14. AYBEY ELEKTRONIK SWLINE Lift Control System USER MANUAL F 7 5 5 02 04 R 3 1 31 OWLINE LIET CONTROL SYSTEM USER MANUAL VERSION 1 04 O AYBEY ELEKTRONIK LTD STI Kartal Cad No 39 81450 Yakacik Istanbul T rkiye Tel 90 216 377 08 02 309 06 45 309 06 54 309 07 18 Fax 90 216 451 58 68 e mail support aybey com Web www aybey com F 7 5 5 02 04 R 4 2 31 CONTENTS 3 PREPBAGE L 2 4 SWLINE SERIES BOARDS AND FUNCTIONS 5 PANEL VOLTAGE INFORMATION 6 OUTPUT TERMINALS AND THE MEANINGS OF THE ABBREV ATIONS 7 CHAPTER 1 LCD SCREEN AND KEYPAD USAGE 8 1 A STARTUP SCREENS evene eder Sete onte o edt 8 1 B MAIN SCREEN eno eed eret veda toit eae 8 i5 INPUTSCREENS Ed ofl au C AR 10 TDI MAT MENU Se ayuy nom nine Ge nee ae a D EAD tus MC 10 1 E SETTING BAR AME FERS A editio e ba es csi inch of m e Mis 11 1 F GIVING CALL BY KEYPAD ette ee ie pM eed 14 1 6 SOFTWARE VERSION NUMBBER saa sassa 14 CHAPTER 2 PARAMETERS au a cise Su see 15 2 A PI MAIN PARAMETERS le pese oru Lh A 15 2 B P2 AUXILIARY PARAMETERS Lee tete
15. E6 R6 OTHER UTILITIES te i Eri yl anl Han ONE OR SR RISE RARE ty PESO QNS 29 CHAPTERS ERROR LOG Bis unti ont area Sonam E na anla qa Te al qa anasu 30 CHAPTER 4 VARIABLES AND LANGUAGE 31 F 7 5 5 02 04 R 4 3 31 PREFACE Swline Series Lift Control System has been designed to fulfill the needs of lift sector at new age One of the main aims of this series is to integrate lift control system with today s advanced computer systems Swline Series Lift Control System is controlled by a 16 bit high performance microcontroller Beside having all features of general lift control systems SWline can also communicate with a computer directly or on a modem through telephone line By this way it is possible to access and observe all lift motion and to edit parameters for authorized users by using a computer In this manual you find information about using SWline Series Lift Control System and technical documents and schematics If you think that this manual is not enough or it is not compatible with hardware or software version of your system you can download latest version of the manual from Aybey Elektronik s web site www aybey com or send an e mail to request by mail We will continue to develop this product with your support and suggestions Therefore if you face any problem while using this product or if you have any suggestions to make it better please inform us by e ma
16. FAILURE PTC AST LIMITS ARE OPEN SLOW LIMITS ARE OPEN SLOW BUT LIM IS OPEN SLOW TOP LIM IS OPEN Up limit signal 817 is cut during up motion SWH IS NOT PRESENT Although lift type is hydraulic A03 3 mainboard SWM can not see Hydraulic Board SWH SWF IS NOT PRESENT Although lift type is speed control 03 gt 3 mainboard SWM can not see Speed Control board SWF DRIVER ERROR RELEVELING ERROR CONTACTOR FAILURE MODEM NOT AVAILABLE 1 TEL BUSY NO ANSWER MODEM INITSTRING ERR 2 TEL BUSY NO ANSWER PAWL NOT ACTIVATED PAWL CONTACT FAILURE PAWL NOT DEACTIVATED 37 _ PAWL PRESSURE FAILURE NO MOTION IN SYSTEM m 17 27
17. bove If you push button on that screen the following screen is seen This screen shows the programmable input signals If you want to turn one back from any screen you can push ESC button once 1 D MAIN MENU If you push ENT button on Main Screen you see the following Main Menu screen gt MI VARIABLES M00 M2 PARAMETERS M3 ERROR LOG M4 LANGUAGE LiSAN 7 5 5 02 04 4 10 31 We will see this kind of menus lots of times The gt Pointer character on most left column points a sub menu and if you want to enter pointed menu you must push ENT button You can move gt by using and J up and down respectively All menus in SWline has a menu number and this is shown at right top corner The number of the Main Menu is 00 as seen above This menu has 5 sub menus In the first screen above you see only 4 of them To see the other use button By this way cursor moves 1 row down at each push If you push J button when the cursor at bottom row all lines moves 1 upper the top line disappear and a new line comes from down as below M2 PARAMETERS 00 M3 ERROR LOG M4 LANGUAGE LiSAN MORO ERVICES Instead of moving 1 step at each time you can use button to see next 4 items and button to see previous 4 items 1 SETTING PARAMETERS To see or change any parameter you must enter M2 PARAMETERS menu For example let s set the parameter Number of Stops In System At firs
18. ct a floor to change its data press ENT key in its line Then you see the following editing screen You can change the data by using and 4 keys between 0 and 1 7 5 5 02 04 R 4 22 31 03 CABIN CALL 2000001 ON The parameters used in this screen are as follows 0 OFF A cabin call for this floor is not allowed 1 cabin call for this floor is always allowed 2 PEL If the clock time is within the time interval PERIOD1 which is specified in section K8 then the cabin call is allowed otherwise not allowed 3 PE2 If the clock time is within the time interval PERIOD2 which is specified in section K8 then the cabin call is allowed otherwise not allowed 2 D 4 K5 HALL CALLS You can set allowance for hall calls for any floor by using this section If you switch off hall call of any floor then any call coming from landing operating panel will be discarded When you enter this section by pressing ENT key in menu M24 then you see the following screen 00 HALL CALL 201 HALL CALL 02 HALL CALL 03 HALL CALL In order to select a floor to change its data press ENT key in its line Then you see the following editing screen You can change the data by using and 4 keys between 0 and 1 Ol HALL CALL 2000001 ON The parameters used in this screen are as follows 0 OFF A cabin call for this floor is not allowed 1 cabin call for this floor is always allowed
19. d 2 C P3 TIMINGS C01 BUSY PERIOD 0 999 Busy period Each number is 0 15 C02 PARK WAIT TIME 0 10000 This parameter stores the time period for the car to move to the park floor Each number is 0 1sec C03 OPEN WAIT PERIOD 0 300 This parameter stores the time period for the automatic door to wait open before closing Each number is 0 1sec C04 DOOR OPEN PERIOD 0 999 This parameter stores the time period necessary for the automatic door to open Each number is 0 15 C05 DOOR LOCK WAIT PERIOD 0 999 This parameter stores the time period necessary for the automatic door to close This parameter is controlled by checking lock terminal 140 after door close command Each number is 0 1sec C06 IN FLOOR WAIT PERIOD 0 999 This parameter stores the time period for the car to wait before departing for the next call in collective systems Each number is 0 1sec C07 STARTUP DELAY 0 100 This parameter stores the time delay for the car to wait before departure after lock contact is closed Each number is 0 15 C08 FLOOR PASS TIME 0 9999 This parameter stores the maximum time allowed to pass without changing the current floor number when the car is in fast or high speed in 3 speed systems Each number is 0 1sec C09 SLOW SPEED MAXIMUM TRAVEL TIME 0 9999 This parameter stores the maximum travel time allowed to
20. eparing conditions for moving Closing door SLOW Car is moving at slow speed FAST Car is moving at fast speed HIGH Car is moving at high speed over 1m s Columns 18 19 20 This group shows information about group operations If lift is SIMPLEX you can not see this group G 1 Lift is the manager of a group and can communicate with the other lift member G 1 Lift is the manager of a group but can not communicate with the other lift member G 2 Lift is the member of a group and can communicate with the other lift manager G 2 Lift is the member of a group but can not communicate with the other lift manager 1 C INPUTS SCREEN You can see the most important inputs and car s motion information on the main screen as explained above To see other inputs push lt button on main screen and you will see the below screen KNGODOOOITATIZA SDL 12954201R907878 On this screen you can see the current case of some important input signals In SWline Series no led is located at signal inputs Instead LCD screen is used to observe input signals input signal names this screen read from top to bottom x symbol the row means 66 19 that the input below x is active And symbol on the top row means that the input is not active The first 5 column 01234 of Row 2 means MO MI M2 M3 M4 inputs The first 3 columns SDL of Row 4 are the same as on main screen described a
21. ers control user defined relay outputs INPUT DEF This parameters control user defined inputs DATE TIME Setting Real Time Clock and date 2 A P1 MAIN PARAMETERS A01 NUMBER OF STOPS 2 32 This parameter stores the number of stops in lift system Be sure to have necessary I O boards SWPI connected to the system required for the selected command system in A02 A402 COMMAND SYSTEM 0 Simple Push Button Car and hall call buttons are tied together There is no call memory 1 Simple Collective Car and hall call buttons are tied together Call memory is present 2 One Button Down Collective Car and hall call buttons are connected separately Car calls are collective in both directions where hall calls are collective when the lift moves downwards This configuration is useful in residential buildings where the main entrance is in the base floor 3 One Button Up Collective Car and hall call buttons are connected separately Car calls are collective in both directions where hall calls are collective when the lift moves upwards 4 Two Buttons Full Collective Car hall up and hall down buttons all are connected separately Car and landing call are all serviced in full collective manner A03 LIFT TYPE One speed rope lift Two speed rope lift Hydraulic lift VVVFI VVVE2 FUJI closed loop RST NT ON WY Q NM 7
22. has several outputs that can drive all common types of inverters By means of the leds on the board it can be observed that which outputs are active Beside necessary relay outputs it has 2 extra relays for user specified purposes SWPI Input Output Board Parallel It transmits the calls to SWM and activates register lamps In order to be able to be identified by SWM it is necessary to connect the jumper whose number is the sequence number of SWPI board according to the SWM SWPEX Display and Signal Lamps Driver Board Parallel It drives the floor displays 2 displays and signal lamps It is added the parallel bus after last SWPI board Common voltage of signal lamps can be selected by a jumper on the board SWPS Power Supply Board It supplies all necessary voltages for control circuit signal circuit and security circuit It also has leakage detection and cut circuit for security circuitry F 7 5 5 02 04 R 4 5 31 PANEL VOLTAGE INFORMATION 150 Security Ground Display Common Voltage 100 24v DC F 7 5 5 02 04 R 4 6 31 OUTPUT TERMINALS AND THE MEANINGS OF THE ABBREVATIONS Dwc ia 0000 DATRIG pr s s 869 Inspection control input C0 C1 C16 Registration button inputs register lamp outputs D Close Door Signal FA z ry 828 840 F Phase failure detector F 7 5 5 02 04 R 4 7131 CHAPTER I LCD SCREEN AND KEYPAD USAGE SWline Series has a 4 r
23. il support aybey com Aybey Elektronik F 7 5 5 02 04 R 4 4 31 SWLINE SERIES BOARDS AND FUNCTIONS SWM Main Board SWM is the main board of the system It reads all inputs by itself and via SWPI It then outputs necessary data to activate motor doors and signal lamps The lift parameters are also stored in SWM They can be easily changed by using keypad and LCD The LCD on SWM displays the current floor target floor state and position of car all registers security circuit inputs state of door s and current time on main window Other inputs can be seen by pressing left button When an error occurs error code blinks on main window SWR Relay Board According to the commands by SWM it produces the outputs which perform all relevant processes with respect to car motion and door By means of the leds on the board it can be observed that what process the lift is performing Beside necessary relay outputs it has 2 extra relays for user specified purposes SWH Relay Board for Hydraulic Systems SWH is the circuit board used in hydraulic systems instead of SWR It has relay outputs that can drive all common types of hydraulic system By means of the leds on the board it can be observed that which valves are active Beside necessary relay outputs it has 2 extra relays for user specified purposes SWF Relay Board for Frequency Regulated Systems SWH is the circuit board specially designed for frequency regulated systems instead of SWR It
24. ll the information about the error is given After a few seconds of display time previous screen is restored B03 PARK FLOOR DEFINITION 0 No park floor is defined 1 System has a park floor When the lift is in park at this floor then it will wait there with closed doors 2 System has a park floor When the lift is in park at this floor then it will wait there with open doors B04 PARK FLOOR 0 31 Park floor number When B03 is 1 or 2 and the lift has no calls about 2 minutes then moves to this floor and stays there until a call comes with the door specified in B03 B05 FIRE FLOOR 0 31 Fire floor number When the fire input of the lift is activated then the car immediately moves to this floor B06 MAXIMUM CABIN CALLS 1 32 Maximum number of allowable cabin calls B07 BREAKPOINT 0 Only for service of the operating system Leave it as 0 Do not change it B08 CONTINUE IN SIMPLE ERRORS 0 The system is stopped after all errors 1 The system continues its operation after some simple errors which are not in security loop or related with car motion B09 WAIT WITH OPEN DOOR IN FLOOR 0 The car waits with closed doors in floor 1 The car waits with open doors in floor F 7 5 5 02 04 R 4 17 31 B10 ERROR MODEM REPORT 0 Not Activated 1 SwOnline In case of error system calls to remote co
25. mputer via modem 2 GSM SMS In case of error system send a short message to defined cellular phone 3 GSM CALL In case of error system calls to defined cellular phone B11 SCHEDULED STATE MODEM Not Activated Activated B12 MAXIMUM ERROR REPEAT 1 100 Maximum allowed number of the same error repeat System locks itself when exceeded B13 LANGUAGE 0 LCD screen language is Turkish 1 LCD screen language is English B14 DISPLAY DRIVER BOARD 0 SWPEX 7 SEGMENT DRIVER 1 SWPEX 2 7 SEGMENT DRIVER 4 SWPEX 2 16 SEGMENT DISPLAY DRIVER B15 PROGRAMMABLE RELAY BOARD 0 Not used 1 Floor indicator lamps 2 Gray code output of floor position 3 Binary output of floor position B16 PAWL CONTROL 0 Active 1 Not active B17 HALL CALLS INHIBIT 0 Hall calls are allowed 1 Hall calls are inhibited B18 CONT INPUT 0 Not active 1 Active B19 DOOR SELECTION 0 Normal The parameters given in Floor Parameters section are valid for door selection at each floor 1 The door to be opened at each floor is determined by the programmable inputs F 7 5 5 02 04 R 4 18 31 B20 AFTER A STOP FAILURE 0 System continues to work 1 System is blocked B21 AFTER A MAXIMUM TRAVEL TIME FAILURE 0 System continues to work 1 System is blocke
26. ocell 5 Pawl Pressure 6 Pawl active closed 7 Pawl active open 8 Door B open control 9 Door A open control 10 Motor motion detection In order to define an input first you must enter its input code from the first table and desired function from the second table After this process you can use this input terminal as an input terminal dedicated for the defined function Be aware of the exception when the lift is used in 3 speed car speed above 1 m sec then I1 and I2 are used automatically as the 3 speed up and down limit switches and the input codes you entered for these are not executed If input code is 0 then this input is ignored 2 H P8 DATE amp TIME The time and date of the system can be set in this section You can edit any item in this screen after selecting its line by using T and J keys and then pressing ENT key Sil DNI AND H DMI MOR eee 2000005 You can change the data by using 7 4 keys In order to go from column to column use lt and keys After you completed your editing press ENT key to save the new data In the same manner you can edit year month day hour and minute F 7 5 5 02 04 R 4 27 31 2 D P9 UTILITIES This section contains some utilities which are some non standard procedures which may help you in configurating your system gt RI DISPLAY UTIL M28 J MC OR E R3 SET PASSWORD R4 OTH UTILITIES 2 1 1 RI DISPLAY UTILITIES In this utilities sec
27. ow 20 character LCD screen and 6 key keypad Keys are located as below lt T gt ESC 4 ENT Functions of the keys differ in different menus But generally ESC is used to exit current menu ENT is used to enter a menu and confirm any input up and down arrows are used to move in menu lists and change value of a variant left and right arrows are used to move left and right while changing the value of variant 1 A START UP SCREENS When system is energized first or restarted the below screen is seen AYBEY ELEKTRONiK LTD SWline series Vx yy System parameters ere mo Ok At this moment system parameters are loaded and below screen is displayed AYBEY ELEKTRON K LTD SWline series Vx yy DD MM YYYY HH MM Meanings of the items in this screen are explained below Vx yy x yy Software Version DD MM YYYY Day Mounth Year DATE HH MM Hour Minute TIME After displaying this screen about second MAIN SCREEN is displayed 1 B MAIN SCREEN SDL gt O1 INS STOP Gil The main screen shows the most important lift parameters briefly F 7 5 5 02 04 R 4 8 31 Security Circuit S Stop 120 D Door Contact 130 Cabin dooris closed L Door Lock 140 System is in Duplex mode SDL 3 e s Aus Y Lift communicating with other lift Error code blinks ERROR NO 5 4014 t02 FAST Direction Lift is manager of group Car is exactly at floor TOP ROW S
28. owing message Brrors are We Ya mq And then you see the list of stored error logs 220010952543 2001 19 406 2001517 iz Here error logs are sorted by date amp time property In this screen you can only see error date time and error code If you want to see more detailed report select an error by using arrow keys and push ENT OLD ERROR REP 2 13 03 2001 17253 PURIS DOOR this screen you see error date amp time at second line At third line floor speed direction of when error occurred are seen And explanation of error is written at last line F 7 5 5 02 04 R 4 30 31 CHAPTER 4 VARIABLES AND LANGUAGE On main menu you see MI VARIABLES at first line gt M1 VARIABLES MOO M2 PARAMETERS M3 ERROR LOG M4 LANGUAGE LiSAN This menu is designed to observe all system variables timers and inputs This is an observation tool for technical persons to investigate system in details However there is no danger for user to enter this menu and observe variables But details of this menu will not explained in this manual Another item in main menu is M4 LANGUAGE LiSAN MI VARIABLES M00 M2 PARAMETERS M3 ERROR LOG gt M4 LANGUAGE LiSAN This is shortcut to menu B 13 that is explained above You can change active menu language by this menu When this manual is prepared supported languages are Turkish and English New languages will
29. pass when the car is in slow speed Each number is 0 15 C10 SERIAL COMMUNICATION ERROR PERIOD 0 500 This parameter stores the maximum time allowed to pass without getting a successful answer in serial communication mode where A09 is 1 Each number is O 1sec F 7 5 5 02 04 R 4 19 31 C11 GROUP DOOR OPEN WAIT PERIOD 0 999 When the lifts work in group then this parameter specifies the maximum time period in which a lift can hold a hall call as its target as its doors are forced to stay open After timeout of this period the hall call is left free where any other member of the group can take it as a target Each number is 0 1sec C12 BRAKE DELAY TIME 0 100 Brake delay in and V V VF systems Each number is 0 1sec This parameter defines the time delay for programmable relays for selection number 18 C13 MOTOR VALVE DELAY TIME 0 999 This parameter determines the delay time between the motor starts to run and the valves are activated in hydraulic lifts in startup Each number is 0 1sec C14 STAR DELTA SWITCHING PERIOD 0 999 This parameter determines the switching time of the motor from star connection to delta connection in hydraulic lifts in startup Each number is 0 1sec C15 VALVE MOTOR DELAY TIME 0 999 This parameter determines the delay time of the valves to shut down after the motor is stopped in hydraulic lift
30. s Each number is 0 1sec C16 MAXIMUM BUSY TIME 0 Inactive 1 30000 If the doors are left open or cannot close for a time period of C16 then the busy signal and cabin light are off until a new call is received C20 DTS BUTTON DELAY 0 Inactive 0 100 DTS Door close button is inhibited during the time period given in this parameter The period starts when the car reaches the floor C21 MAXIMUM MOTION WAIT PERIOD 0 100 If there is no signal input to the programmable input with code 10 within the time period specified in this parameter after a motion command is received then the system is stopped C22 RETIRING CAM DELAY 0 100 Time period to delay the activation of retiring cam after the landing door has been closed for semi automatic systems 2 D P4 FLOOR PARAMETERS In this section you can program the parameters of the system that can vary floor to floor We call these parameters as Floor Parameter In screen M20 item P4 is the selection for floor parameters If you select P4 and press ENT key then the following screen is displayed DISPLAYS 24 gt 2 DOOR A o DOO 4 CALLS F 7 5 5 02 04 R 4 20 31 The menu M24 consists of the following sections K1 SET DISPLAYS K2 SET DOOR A K3 SET DOOR B K4 CABIN CALLS K5 HALL CALLS K6 ENCODER PULSE 2 D 1 K1 SET DISPLAYS In this section you are faced with
31. t take the lift in inspection mode MI VARIABLES M00 gt 2 5 M3 ERROR LOG M4 LANGUAGE LiSAN In Main Menu screen use D buttons and when the Pointer points M2 PARAMETERS as above push ENT button You will see the M20 menu screen as below gt P1 MAIN PRMs M2 0 P2 AUX PRMS P3 TIMINGS P4 FLR PARAMET Here again push ENT button when the Pointer points PI MAIN PRMs as above Then you see the first 4 items of Main parameters as below This menu has 12 items as A01 A02 A12 You can see the other items buy using arrow keys as described before Some of the items in this screen are in abbreviated form To see full form of any item push ENT button when the Pointer points it gt AOQL NUM OF OE 16 A02 COMMAND 4 AQS LIET TPE AO04 DOOR TYPE 7 5 5 02 04 R 4 11 31 To change the parameter A01 push ENT again A01 NUMBER OF EPIS TI S SIM 000016 Now you see general parameter change screen In this type of screens you always see 6 digit numbers When you first enter this screen cursor is always located under left most digit You can increase or decrease value of the digit under which cursor is located by using J buttons respectively You can move cursor left and right by using lt buttons In this screen stored parameter data is 16 and cursor is located under digit 6 Now let s see some example about how to change value of a parameter 2000016 L 20
32. the following screen QQ FLR DISPLAY 9 QL FLR DISPLAY 9 D2 FLR DISPLAY DOSCPLhRODISEDLAY When you select any floor by pressing ENT key then you can enter the digital display data by using the following display input screen DELEN LEFT _ RIGHT 2 CHARACTERS This screen is designed to take input left and right digital characters When you enter this screen first the cursor is waiting just after LEFT Here either you can skip this field by pressing ENT key and accepting the character shown there or select the character by using or L keys As you scan characters all ASCII characters will be displayed one by one You can select any one you want to be displayed in car and landing panels However the hardware you are using to drive and display these characters limits the characters you actually see on the displays For example if you have seven segment digital displays on your panels then you can see the characters only if you select in this section the characters of all digits from 0 to 9 and other characters like A b C d E L F H L L P r U If you have such hardware in your system then you cannot see any characters like M or X on panels if you select them But if you have dot matrix displays and its driving hardware is connected in your system then you can actually display on panels all characters you select in this section After you have chosen the character you want on the left
33. tion the following screen is Waiting for an input BASE FLOOR N 000000 You can change the data by using T and 4 keys between 0 and maximum floor no If you specify which floor is the entrance floor to the building then this utility sets the digital display of the entrance floor base floor as 0 All floors above this floor are numbered starting 1 and incremented by 1 at every floor All floors below 0 base floor are numbered starting 1 and decremented by 1 at every floor If you have a regular display order in your system but with a few exceptions then first use the utility explained above and then change the data for exceptional floors one by one 2 I 2 R2 FACTORY SETTINGS If you want to set all parameters to the values set just after production then you can use this section 2 I 3 R3 SET PASSWORD You can change your password by this utility When you enter this menu current password is asked first Quei enit Pass 0O00UO If you enter correct password then you can enter new password between 0 and 32000 then push ENT Current pass 012345 New password 010101 Confirm new passw ENTER SAVE Here if you again push ENT new password will be saved But you can cancel changes by pushing ESC F 7 5 5 02 04 R 4 28 31 2 1 4 R4 MODEM SETTINGS In this section you can adjust your modem which must be used for remote PC connection gt 01 1 X02 PHONE 2 2
34. to the programmable relays OUTPUT CODE EVENT WHICH MAKES K2 ON l 7 8 The car is not moving in Slow speed c r 9 Thecaris not moving The car is moving in any speed 10 The car is moving in Fast speed The car is moving in Fast or High speed Retiring cam In normal mode The system is in motion or in braking In inspection mode The system is in motion The system is in motion or door lock is on There is no call registered The car is staying in rest at 1 th floor i represents the floor at which the car stays and has a range from 0 to maximum number of stops 1 For example 203 represents 4 stop and 200 represents base floor 2 G P7 INPUT DEFINITIONS It is possible to define some inputs for a specific job In order to do this first select P6 in menu M20 You are faced with the following screen INE UL DER ENED TON impute No 20000010 Input Code 000000 F 7 5 5 02 04 R 4 26 31 The programmable inputs are denoted by I1 I2 I3 and on the printed circuit boards INPUT NO INPUT NAME REMARKS 1 A11 must 0 for programmable input If A11 1 Il is used as high speed 3 speed down limit switch 2 P 11 must be 0 for programmable input If A11 1 I2 is used as high speed 3 speed up limit switch 3 Free input 4 14 Free input INPUT CODE FUNCTION 1 FIREMAN 2 WATMAN 3 Fast Inspection Travel 4 Phot
Download Pdf Manuals
Related Search