User Manual
Contents
1. The Alarm Output time is adjustable between 0 3 minutes with the default being 1 minute To disable door open detection 6 0 Factory default To enable door open detection 6 1 Alarm output time To set the alarm output time 0 3 9 0 3 minutes Factory default is 1 minute 11 Keypad Lockout amp Alarm Output options If there are 10 invalid cards or 10 incorrect PIN numbers in a 10 minute period either the keypad will lockout for 10 minutes or the alarm will operate for 10 minutes depending on the option selected below Normal status No keypad lockout or 7 0 Factory default setting alarm factory default Keypad Lockout 7 1 4 Alarm Output 7112110 To remove the alarm To reset the Door Forced Open warning Read valid card or Master Code To reset the Door Open Too Long warning Close the door or Read valid card or Master Code 12 Interconnecting Two Devices 12 1 W1 C W3 C operating as a Wiegand Output Reader In this mode the W1 C W3 C supports a Wiegand 26 bit output so the Wiegand data lines can be connected to any controller which supports a Wiegand 26 bit input See figure 1 Pink Gan po DO DL S D1 CND SH Grey MD ALARM V Yellow HD OPEN EED D IN AC amp DC Black MB AC amp DC Blue E No2. is removed from the cover then the tamper alarm will operate 10 Sound and Light indication Operation Status Red Light Green Light Yellow Light Buzzer Power on Bright Short Ring Stand by Bright Press keypad Short Ring Operation successful Bright Short Ring Operation failed 3 Short Rings Enter into programming mode Bright S F Short Ring In the programming mode x Bright gt Exit from the programming Bright Short Ring mode Open the door Bright Short Ring Alarm Bright Alarm 11 11 1 User Settings W1 C W3 C Detailed Programming Guide To enter the programming mode Master codel W 888888 is the default factory master code To exit from the programming mode Note that to undertake the following programming the master user must be logged in To change the master code 0 The master code is any 6 digits itt itt New code New code Setting the working mode Set valid card only users Set valid card and PIN users Set valid card or PIN users 1310110 Entry is by card only 3 1 Entry is by card and PIN together 3 2 Entry is by either card or PIN default To add a user in either card or PIN mode 3 2 Default setting To add a Pin user User ID num
3. user a N Users can be deleted continuously without exiting from programming mode To unlock the door To unlock the door for a PIN user Enter the PIN then press 7 To unlock the door for a card user Present the card 3 Description The W1 C W3 C is single door multifunction standalone access controller or a Wiegand output keypad or card reader It is suitable for mounting either indoor or outdoor in harsh environments It is housed in a strong sturdy and vandal proof Zinc Alloy electroplated case which is available in either a bright silver or matt silver finish The electronics are fully potted so the W1 C W3 C is waterproof and conforms to IP68 The W1 C W3 C supports up to 2000 users in either a Card 4 8 digits PIN or a Card PIN option The inbuilt card reader supports EM 125KHZ frequency cards tags The W1 C W3 C has many extra features including block enrollment wiegand 26 bits interface and backlit keypad etc These features make W1 C W3 C an ideal choice for door access not only for small shops and domestic households but also for commercial and industrial applications such as factories warehouses laboratories banks and prisons 4 Features Waterproof conforms to IP68 Strong Zinc Alloy Electroplated anti vandal case Full programming from the keypad 2 000 users supports Card PIN Card PIN Can be used as a stand alone keypad Pin length
4. 10 To delete ALL users Note that this is a 2 0000 dangerous option so use with care To set card users by Manager card Manager add card Read card Manager add card To aad EEE Manager Add card Cards can be added continuously To delete User by Manager Delete Card Manager delete card Read Card Manager delete card Cards can be deleted continuously To unlock the door For a PIN user Enter the PIN then press For a card User Read card For a card and PIN user Read card then enter PIN 11 2 Door Relay Door Detecting Alarm Settings Door relay time setting To set door relay strike time The door relay time is between 0 99 seconds the factory default setting is 5 seconds Door Open Detection Door Open Too Long DOTL warning When used with an optional magnetic contact or built in magnetic contact of the lock if the door is opened normally but not closed after 1 minute the inside buzzer will beep automatically to remind people to close the door and continue for 1 minute before switching off automatically Door Forced Open warning When used with an optional magnetic contact or built in magnetic contact of the lock if the door is opened by force or if the door is opened after 20 seconds of the electro mechanical lock not closed properly the inside buzzer and alarm output will both operate
5. 4 8 digits Backlight keypad Wiegand 26 input amp output One programmable Relay output NO NC COM Adjustable Door Output time Alarm time Door Open time Block enrollment can enroll maximum 2000 consecutive card within 2 minutes Very low power consumption lt 60mA Easy to install and program Built in light dependent resistor LDR for anti tamper Built in buzzer Red Yellow and Green LEDs display the working status 12 24V AC DC Two year warranty 5 Specifications Operating Voltage 12 24V AC DC User Capacity 2 000 Keypad 12 keys 2 x 6 digits W1 C 12 keys 3 x 4 digits W3 C Card Type EM 125 KHZ card Card Reading Distance 3 6 cm Active Current lt 80mA Idle Current lt 40mA Lock Output Load Max 2A Alarm Output Load Max 20A Operating Temperature 20 60 C Operating Humidity Environment 5 95 RH Conforms to IP68 Adjustable Door Relay time Adjustable Alarm Time 0 99 seconds 0 3 minutes Wiegand Interface Wiegand 26 input amp output Wiring Connections Electric Lock Exit Button DOTL External Alarm Dimensions L135 x W58 x H26 mm W1 C L128x W82 x H28 mm W3 C Net Weight 550 g Gross Weight 700 g 6 Installation Remove the back cover from the keypad using the supplied security screwdriver Drill 4 holes on the wall for the screws and hole for the cable Fix the back cover firmly on the wall with 4 flat head screws Thr
6. Purple EED COM Controller Orange i NG With Wiegand 26 input WI C Figure 1 Transmission Format 1 Keypad Transmission The Reader will transmit the PIN data when it receives the last key press after PIN code 12 Format PIN Code any 4 8 digits between 0000 99999999 Example PIN code 111111 Press 111111 then the output format will be 00111111 Note if press an invalid PIN any 4 8 digits the data will be also transmitted 2 Proximity Card Transmission The Reader will transmit the card data when it reads the Card Format Card Number the last 8 digits of Card Number Note no matter the card is valid or invalid the data will be transmitted 12 2 W1 C W3 C operating as a Controller In this mode the W1 C W3 C supports a Wiegand 26 bit input so an external Wiegand device with a 26 bit output can be connected to the Wiegand input terminals on the W1 C W3 C Either an ID card reader 125 KHZ or an IC card reader 13 56MHZ can be connected to the W1 C W3 C Cards are required to be added at the external reader except where an external EM reader is used in this case cards can be added at either reader or controller See figure 2 Special Power Supply Wiegand reader NC COM NO 12V GND OPEN laran YY Y YY DO kaa me ll eed Grey GND Yellow es E D detecti it Brown oor detecting swite rea eee love Purple Orange Figure 2 13
7. Waterproof Keypad Reader Controller User Manual EELER aE 1 Packing List Name Quantity Remarks Digital Keypad W1 C W3 C 1 User manual 1 Screw driver 1 Rubber bungs 4 6 27mm used for fixing Self tapping screws 4 3 5 27mm used for fixing Manager Card 2 Manager Add Card amp Manager Delete Card Please ensure that all the above contents are correct If any are missing please notify the supplier of the W1 C W3 C 2 W1 C W3 C Quick Reference Programming Guide To enter the programming mode Master code W 888888 is the default factory master code To exit from the programming mode S Note that to undertake the following programming the master user must be logged in To change the master code 0 Newcode ff New code W The master code can be 6 digits long To add a PIN user 1 User ID number PIN The ID number is any number between 1 2000 The PIN is any 4 8 digits between 0000 99999999 with the exception of 1234 which is reserved Users can be added continuously without exiting programming mode To add a card user 1 Read Card Cards can be added continuously without exiting from programming mode To delete a PIN or a card user P User ID number H for a PIN user or Read Card H for a card
8. ber PIN The ID number is any number between 1 2000 The PIN is any 4 8 digits between 0000 99999999 with the exception of 1234 which is reserved Users can be added continuously without exiting from programming mode as follows 1 User ID no 1 PIN User ID no Zj PIN H To delete a PIN user To change the PIN of a PIN user This step must be done out of programming mode 2 User ID number Users can be deleted continuously without exiting programming mode S ID number Old PIN New PIN New PIN To add a card user Method 1 This is the fastest way to enter cards using ID number auto generation 1 Read card Cards can be added continuously without exiting programming mode To add a card user Method 2 This is the alternative way to enter cards using User ID Allocation In this H ID number Card method a User ID is allocated to a card Only one user ID can be allocated to a single card To add card user Method 3 Add a series cards users Block Enrollment 5 ID number B digits Card number Card quantity within 2 minutes Card quantity is between 1 2000 The 8 digits card number is the last 8 digits on the card Maximum 2000 cards can be enrolled at a stretch To delete a car
9. d user by card number Note users can be deleted continuously without exiting programming mode 2 Read Card H To delete a card user by user ID This option can be used when a user has lost their card 2 UserID To add a card and PIN user in card an d PIN mode 2 1 To Add a card and Pin user The PIN is any 4 8 digits between 0000 amp 99999999 with the exception of 1234 which is reserved Add the card as for a card user Then allocate the card a PIN as follows Read card 1234 PIN PIN Press E to exit from the programming mode To change a PIN in card and PIN mode Method 1 Note that this is done outside programming mode so the user can undertake this themselves PIN Read Card Old PIN New PIN New To change a PIN in card and PIN mode Method 2 Note that this is done outside programming mode so the user can undertake this themselves ID number Old PIN New PIN New PIN To delete a Card and PIN user just delete the card 2 User ID To add a card user in card mode 8 0 To Add and Delete a card user card user in B 2 The operating is the same as adding and deleting a To delete All users
10. ead the cable through the cable hole Attach the keypad to the back cover W1 C W3 C PCB connect diagram 7 Wiring Color Function Description Green DO Wiegand Output DO White D1 Wiegand Output D1 Grey Alarm Alarm Negative Yellow OPEN Request to Exit Button Brown D In Door Contact Red 12V 24V AC amp DC 12 24V AC amp DC Regulated Power Input Black 12V 24V AC amp DC 12 24V AC amp DC Regulated Power Input Blue NO Relay NO Purple COM Relay COM Orange NC Relay NC Pink GND W1 C W3 C Negative Connection Diagram Alarm ce z Zr Power Alarm DC12V 3A mc com wo 127 GHD ora Do a Green White Exit button Common Power Supply Special Power Supply Notes Connect the negative pole of the lock to NC is for Fail safe lock Connect the negative pole of the lock to NO is for Fail secure lock 8 To Reset to Factory Default To reset to factory default power off press S hold it and power on release it until hear two beeps and the LED shines in orange then read any two EM cards the LED will turn in red means reset to factory default setting successfully Of the two EM cards read the first one is Manager Add card the second one is Manager Delete card Remarks Reset to factory default the user s information is still retained 9 Anti Tamper Alarm The W1 C W3 C uses a LDR light dependent resistor as an anti tamper alarm If the keypad
Download Pdf Manuals
Related Search