CP5-Series User Manual - Quality Certification Services
Contents
1. OUTZ Zero point has drifted out of the acceptable range Try to perform a calibration adjustment If the problem persists the load cell may be permanently damaged due to overloading 2 EEEE Overload The maximum capacity has been exceeded Remove the extra weight to avoid permanently damaging the load cell oo 3 Batteries are low Replace the batteries XII Specifications PK 110 Manual PK 110 0 44Ib 44 110Ib 0 05 b 0 1Ib 100g 0 2Ib 2 x 1 5V AAA Alkaline Dimensions 4 8 x 3 5 x 1 0 in Hook Dimensions Gap 0 8 in Throat 1 0 in Warranty 10 Year Limited Warranty XIII Capacity Readability Chart Dual Range Range 0 44Ib Range2 44 110Ib 0 44lb x 0 05lb 44 110lb x 0 1Ib 0 20kg x 0 02kg 20 50kg x 0 05kg 0 7050z x 10z 705 17620z x 20z American Weigh Scales Inc Norcross GA 30092 Made In China to our exact specifications and quality control2. ALUS American Weigh Scales PK 110 User Manual PK 110 0 44lb x 0 05lb 44 110lb x 0 11b Copyright 2012 American Weigh Scales Inc All rights reserved Rev 1 1 PK 110 Manual Thank you for purchasing the American Weigh PK 110 multi use hanging scale Please read all operating instructions carefully before use Scales are precision measuring devices and should always be handled with proper care To ensure years of reliable service keep these simple tips in mind Do not exceed the scale s maximum capacity Store your scale in a clean dry location Dust dirt and moisture can accumulate on the weighing sensors and electronics causing inaccuracy or malfunction Avoid using your scale in close proximity to strong radio wave emitting devices such as cordless phones When weighing heavy items use proper lifting technique to avoid back injury Do not drop items onto the weighing hook This may cause damage to the load sensor Avoid dropping your scale The warranty does not cover damage due to rough treatment or overload Check the batteries first if you are having any trouble with your scale This simple step can remedy most scale issues Calibration should be checked and adjusted occasionally as part of routine scale maintenance I Part List 1 Scale 2 AAA Batteries x2 Il Key ee we 1 E Turns the scale on or off 2 Zero Tare Key Re zeros the scale Use
3. d to remove the weight of a tray or container 3 Unit Key Tap to change the displayed unit of measure Hold to enter calibration see IX lll Battery Installation Proper Battery Installation PK 110 Manual Low batteries can cause inaccuracy in digital scales If you are experiencing issues with your scale first try new batteries Most times this will solve the problem 1 Before using the scale for the first time check the battery compartment and remove any plastic insulation strips or packaging that may be in place to prevent battery drainage during shipping storage 2 If you are replacing the batteries make sure the positive and negative contacts are properly aligned IV Operation 1 Press the ON OFF Q key to turn the scale on 2 Once the start up process completes and the scale goes to zero you are ready to weigh 3 Place the quantity to be weighed onto the weighing hook 4 Wait a couple seconds for the display to stabilize before taking a weight reading 5 To turn the scale OFF press the ON OFF key again V Hold Settings This scale has three different hold settings Follow these instructions to change the hold setting 1 2 With the scale OFF press and hold the Z T key then ap the ON OFF Q key Release both keys when you see on the display Tapping the Unit key will cycle through the three hold settings Auto Hold Weight reading is held on the A
4. rom the weighing hook and press he ZIT key again to re zero the scale Vill Calibration Initial calibration is performed at the factory However calibration may need to be checked and adjusted in some rare cases or after heavy usage To check calibration 1 Place the required calibration weight on the scale and note the displayed value 2 If the displayed value is not within acceptable tolerance see chart below adjustment is required Model Satan Calibration Recommended Tolerance Weight Accuracy Class IX Adjustment 1 Press and hold the Unit key until the display shows CAL followed by a random number ISN 2 Make sure nothing is on the weighing hook then press the ZIT key 3 The display will flash 20 00kg Place exactly 20 00kg on the weighing hook and press Z T when the weight has steadied 4 The display will flash PASS then return to normal weighing mode Adjustment is complete X Troubleshooting Problem Scale will not turn on Solution Check the batteries and battery contacts Problem Displayed weight fluctuates randomly Solution Make sure to hold the device as still as possible or hang it from a fixed point In some cases nearby radio wave emitting devices can cause fluctuations Problem Displayed weight is inaccurate Solution Perform a calibration adjustment If you are still having trouble contact our warranty department XI Error Codes 1
5. ub o display after stabilization This allows you to read the weight even after removing the item from the weighing hook Hold will display underneath the weight when locked Peak Hold Highest weight reading is held PEHE on the display This mode can be used to measure a bow s draw weight or for other force measuring applications Hold will display underneath the weight when locked m nee Hold Disabled Weight is no longer held on U the display 3 Press the ON OFF key to confirm your selection and turn the scale off VI Changing the Unit of Measure 1 Press the Unit key to change the scales displayed unit of measure 2 If the scale is turned off then back on it will default to the last unit used PK 110 Units Ib pound oz ounce kg kilogram Vil Using the Tare Feature You can use this scale s tare feature to subtract the weight of an empty container for net weight determination NOTE The weight of the container will subtract from the available capacity subtractive taring PK 110 Manual 1 Place the empty container or vessel on the weighing hook 2 Press the Z T key once The display will then reset o zero If the container is removed its weight will be displayed as a negative number 3 You may now fill the container with the quantity to be weighed The display will show the net weight of he contents 4 To return to normal weight display gross weight remove any items f
Download Pdf Manuals
Related Search