NS-IC600/NS-IC800
Contents
1. IN CEILING SPEAKER ENCEINTE ENCASTRABLE POUR PLAFOND NS IC600 NS IC800 OWNER S MANUAL MODE D EMPLOI BEDIENUNGSANLEITUNG MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES NO fe AA d CONSUMER PRECAUTIONS Read these precautions carefully before setting up your NS IC600 NS IC800 speakers When mounting these speakers be sure to work with two or more persons for safety Do not attach them to thin plywood or soft ceiling surface materials as the screws may tear free causing the speakers to fall and become damaged or result in personal injury Do not fasten the speakers to a ceiling with nails adhesives or Information for Users on Collection and Disposal of Old Equipment This symbol on the products packaging and or accompanying documents means that used electrical and electronic products should not be mixed with general household waste For proper treatment recovery and recycling of EN products please take them to applicable collection points in accordance with your national legislation and the Directives 2002 Do not place the speakers where they are liable to be knocked Eds iroctives 2002 96 over or struck by falling objects Stable placement will also ensure better sound performance other unsafe hardware Long term use and vibrations may cause them to pull free By disposing of these products correctly you will help to sa2. 5 Re install the grille on the speaker SPECIFICATIONS NS IC600 NS IC800 Type 2 way Open back type Drive Tweeter 2 5 cm 1 Soft dome type iver Woofer 16 cm 6 5 Cone type 20 cm 8 Cone type Frequency 2 3 response 65 Hz to 28 kHz 10dB 50 Hz to 28 kHz 10 Impedance 8 ohms Nominal input 40 50 W Maximum input 110 W 140 W Sensitivity 90 dB 2 83 V 1 m Crossover frequency 3 2 kHz 3 5 kHz Dimensions 242 x 119D mm 0283 x 120D mm with grille 9 1 2 x 4 5 8 D 11 1 8 x 4 3 4 D Weight with grille 1 5 kg 3 3 Ibs 1 9 kg 4 2 Ibs Specifications subject to change without notice due to product improvements Speaker cables are not included with this model 6 En YAMAHA YAMAHA CORPORATION 2010 Yamaha Corporation Printed in Indonesia WV73960 2
3. com for U K resident The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase Yamaha undertakes subject to the conditions listed below to have the faulty product or any part s repaired or replaced at Yamaha s discretion without any charge for parts or labour Yamaha reserves the right to replace a product with that of a similar kind and or value and condition where a model has been discontinued or is considered uneconomic to repair Conditions 1 The original invoice or sales receipt showing date of purchase product code and dealer s name MUST accompany the defective product along with a statement detailing the fault In the absence of this clear proof of purchase Yamaha reserves the right to refuse to provide free of charge service and the product may be returned at the customer s expense 2 The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area EEA or Switzerland The product must not have been the subject of any modifications or alterations unless authorised in writing by Yamaha The following are excluded from this guarantee a Periodic maintenance and repair or replacement of parts due to normal wear and tear b Damage resulting from 1 Repairs performed by the customer himself or by an unauthorised third party 2 Inadequate packaging or mishandling when the product is in transit from t
4. this case move the speakers away from the TV This is not an issue with LCD and plasma TVs Stereo For best stereo performance install the left and right speakers at equal distance from the listening position Each speaker should be separated by a distance of 1 8 3 0 m 6 10 ft 2 En Home Theater when using as surround speakers Use these speakers for left and right surround channels Surround speakers should ideally be placed behind the listening area at least as far apart as the front speakers and up to 60 additional centimeters 2 additional feet apart per side NS IC600 NS IC800 NS IC600 NS IC800 INSTALLATION Before installation The following is the recommended procedure for installing the speakers in a ceiling Please read it carefully before installation Before you begin installation read this owner s manual completely and consult your local building codes If you have any doubt contact your dealer or a qualified audio video installer Before installing the speakers run the speaker cables to the installation location Ceiling board thickness and clearance space above ceiling Check to ensure that the area you are installing the speaker is free of any ceiling joints or studs by tapping the ceiling or using a stud finder Make sure that there is sufficient space on the ceiling for installation and that there are no obstructions such as ducts pipes etc
5. See the following chart for external product dimensions and ceiling installation measurements The thickness required for the ceiling boards is 5 30 mm 1 4 1 1 8 A B D NS IC600 NS IC800 C Diameter A 231 mm 9 1 8 272 mm 10 3 4 Depth B 113 5 mm 4 1 2 113 5 mm 4 1 2 2 Depth 109 mm 4 1 47 109 mm 4 1 47 Diameter D 204 mm 8 245 mm 9 5 8 GUTOUT TEMPLATE The size differs depending the model Refer the above chart When installing your NS IC600 NS IC800 in ceiling speakers be aware of the product weight See specification page and the sturdiness of the material into which you are installing the speaker Be aware of any concealed studs electrical wiring or plumbing in the ceiling into which you are installing the speakers If you are not sure of a safe way to install these speakers consult a professional installer or a building contractor CAUTION When installing the speaker do not touch the woofer or tweeter units with your hands or expose them to excessive physical shock If they are dented or bent the sound will be distorted NOTE f you wish to paint the speaker grille refer to page 6 PAINTING THE SPEAKER GRILLE before proceeding 3 En How to install This is the recommended installation procedure when 1 5 Insert the tip of a keyhole saw into the pilot hole the materi
6. al of the installation location is plasterboard and then cut all of the way around the circular 7 Position the cutout template where you are outline installing the speaker 2 Trace a line around the template with a pencil The mark for the center of the hole is also required WARNING When using a keyhole saw or cutting tool use safety goggles for eye protection and be sure to observe all safety precautions 6 Pull the speaker cable out of the hole which you have cut 3 Drill the pilot hole at the center mark made on the Leave some extra length of cable when pulling the cable ceiling out 7 Connect the speaker cable to the speaker For detailed instructions refer to page 6 CONNECTING YOUR AMPLIFIER RECEIVER WARNING When using a drill or cutting tool use safety goggles for eye protection and be sure to observe all safety precautions 8 Place the speaker into the ceiling 4 To check the space behind the hole insert a bent sturdy wire such as a coat hanger into the hole and then slowly rotate the wire to check for any obstruction If there is any obstruction patch the hole and select another location CAUTION When installing the speaker do not touch the tweeter dome or woofer cone directly This may cause a malfunction 5 Make sure that mounting clamps are turned inward when e V installing the speaker in a ceiling 360 4 En 9 ins
7. e side of each terminal NS IC600 NS IC800 R NS IC600 R NS IC800 L A t 9 9 OO Receiver or amplifier Speaker output terminals 4 Release the terminal Test the firmness of the connection by pulling lightly on the cable at the terminal CAUTION Do not let the bare speaker wires touch each other as this could damage the speaker or amplifier receiver or both After connecting Lower the power amplifier receiver volume control before changing input sources Never change input sources for example FM to CD at high listening levels Always turn the receiver amplifier unit off when installing or removing any cables Anytime you note distortion reduce the volume control on your power amplifier receiver to a lower setting Never allow your power amplifier to be driven into clipping PAINTING THE SPEAKER GRILLE The speaker grilles can be painted to match your room d cor Use high quality spray paint and select a well ventilated area before proceeding 1 Carefully remove the grille from the speaker if attached 2 Remove the scrim cloth that is attached to the back of the grille The adhesive that holds the cloth in place is reusable 3 Apply the paint to the grille Make sure that the grille holes remain free of paint Clogging the holes with paint may diminish the sound quality When the paint has fully dried re attach the scrim cloth to the back of the grille
8. ert the speaker into the hole Loosen four screws approximately one turn counter clockwise It will allow the clamps to open easily A Loosen Evenly tighten each of the four mounting screws clockwise using a Philips screwdriver At this time these four mounting clamps open in the ceiling These opened clamps will press the ceiling board and the speaker together to secure the speaker Tighten screws until the mounting clamps sufficiently grip the ceiling Tighten the screws firmly to secure the speaker to the ceiling C H 5 Tighten AUTION When tightening the screws do not screw too tightly This may cause breakage of the mounting clamps and fracture of the wallboard We recommend using only hand tools as power screwdrivers may over tighten the screws Should you use a power screwdriver be certain to select a very low torque setting to prevent damage to the speaker or to the wallboard Make sure that none of the screws are loose and that there are no gaps between the speaker and the ceiling INT Tighten the screws in order of opposite sides rather than clockwise or counter clockwise direction such as right and left then top and bottom En 10 Adjust the angle of the tweeter Gently press the outer edge of the tweeter housing toward the listening position This tweeter movable angle is about 15 in multiple directions Tweeter movable angle CAUTION When ad
9. he customer Please note that it is the customer s responsibility to ensure the product is adequately packaged when returning the product for repair 3 Misuse including but not limited to a failure to use the product for its normal purpose or in accordance with Yamaha s instructions on the proper use maintenance and storage and b installation or use of the product in a manner inconsistent with the technical or safety standards in force in the country where it is used 4 Accidents lightning water fire improper ventilation battery leakage or any cause beyond Yamaha s control 5 Defects of the system into which this product is incorporated and or incompatibility with third party products 6 Use of a product imported into the EEA and or Switzerland not by Yamaha where that product does not conform to the technical or safety standards of the country of use and or to the standard specification of a product sold by Yamaha in the EEA and or Switzerland 5 Where the guarantee differs between the country of purchase and the country of use of the product the guarantee of the country of use shall apply 6 Yamaha may not be held responsible for any losses or damages whether direct consequential or otherwise save for the repair or replacement of the product Please backup any custom settings or data as Yamaha may not be held responsible for any alteration or loss to such settings or data This guarantee does not affect the consumer s sta
10. justing the tweeter do not rotate it This may cause the breakage of the tweeter 1 1 Attach the speaker grille to the speaker As several magnets are on the speaker frame attach the grille to the frame directly When attaching the grille make sure that the grille is attached to the Speaker securely to keep the grille from falling CAUTION Be very careful when removing the grille as it may fall or cause injury Also try to place an equal amount of pressure on the circumference when removing the grille The grille may bend if too much pressure is placed in one location CONNECTING YOUR AMPLIFIER RECEIVER Before making connections make sure that the amplifier receiver is switched off When connecting also refer to the owner s manual of the connected equipment Connections Connect the push input terminals at the rear of the speakers to the speaker output terminals of the amplifier receiver with the speaker cables not included Connect each speaker making sure not to reverse the polarity red black If the speaker is connected with reversed polarity the sound will be unnatural and lack bass How to connect 1 Remove approximately 10 mm 3 8 of insulation from the end of each speaker cable using wire strippers and then twist the exposed wires of the cable together to prevent short circuits 2 Press and hold down the speaker terminal 3 Insert the bare wire into the hole in th
11. tutory rights under applicable national laws in force or the consumer s rights against the dealer arising from their sales purchase contract Ao 1 En CONTENTS CONSUMER PRECAUTIONS 1 CONNECTING YOUR AMPLIFIER RECEIVER 6 CONTENTS wid Connections sese 6 PREPARATION wid How to connect 6 Optimum installation layout 2 After connecting 6 1 5 3 PAINTING THE SPEAKER GRILLE 6 6 Before installation 3 SPECIFICATIONS cere How to Ifistall sasana ak ni sa apaa engi anaa ani Ress 4 PREPARATION r Unpacking Tools needed for installation After unpacking check that the following items are When installing the speakers to the ceiling you will contained need to prepare the following tools Use an appropriate tool for the material of the mounting surface 2 Pencil Drill Philips screwdriver NS IC600 NS IC800 2 Speaker x 2 Wire strippers Safety goggles Keyhole saw CUTOUT NG Speaker grille lt 2 Cutout template x 1 Sturdy wire Gloves such as a coat hanger Optimum installation layout Placing the speakers too close to a CRT type TV may impair the picture color or cause a buzzing noise In
12. ve valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling Do not attempt to modify or fix the speakers Contact qualified Yamaha service personnel when any service is needed Do not attempt to clean the speakers with chemical solvents as this might damage the finish To clean wipe with a dry soft For more information about collection and cloth recycling of old products please contact your local municipality your waste disposal service or Secure placement or installation is the owner s the point of salewhere you purchased the items responsibility Yamaha shall not be liable for any accident caused by improper placement or installation of speakers Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union If you wish to discard these items please contact your local authorities or dealer and ask for the correct method of disposal Limited Guarantee for European Economic Area EEA and Switzerland Thank you for having chosen a Yamaha product In the unlikely event that your Yamaha product needs guarantee service please contact the dealer from whom it was purchased If you experience any difficulty please contact Yamaha representative office in your country You can find full details on our website http Awww yamaha hifi com or http www yamaha uk
Download Pdf Manuals
Related Search
NS IC600/NS IC800