USER MANUAL - Ecologeek4u
Contents
1. 25 the color LED shows the warning level once a second and the main LED flashes 2 times once a minute Critical level lt 5 is color indicated twice a second and light output decreases to Firefly1 and then switched off High temperature When it increases to the warning level the color LED flashes 3 times once a second At critical level the main LED flashes 4 times once a minute and the light output decreases to Main3 mode In case the temperature doesn t fall the light output decreases to Firefly2 At normal temperature the brightness increases to usual level2. between the last used modes in Section 1 and Section 2 3 clicks To turn on the Maximum mode Section 3 OFF Special Strobe Any mode Special av 4 clicks To turn on the last used Special mode Section 4 Bi pa Only C2 Pro has 2 types of operation State Indication Switching State Indication ON OFF 1 General The flashlight is switched on off permanently Battery level 1 2 2 Tactical The light turns on for the time the button is being pressed It will Ea switch on in the last memorized mode except for the Special modes This M Py type of operation is useful for short time lighting and setting signals nS rR Ssec Press amp Hold To access the Tactical operation type unscrew the tailcap to 1 4 press the button and tighten the tailcap again keeping the button pressed To return to Low Battery indication High Temperature Indication the General type unscrew the tailcap to 1 4 and tighten it again Warning Critical Warning Critical You have a convenient momentary access to all Modes A N A Main Double click from OFF or ON state turns on the last used Main Mode Firefly Press and hold the button in OFF state to turn on the Firefly1 Press fi f 2 2 and hold after Firefly activation to start cycling through the Firefly modes sec 05sec 41sec 1sec 5 HoT release the button to select one Firefly modes can be also accessed from the Main mode by a double click gt Firefly1 gt Main3 DOF PFi
3. DH iT Jt C2 Pro only With ambient temperature 25 C the flashlight delivers light in Maximum mode for about 8 10 minutes and then the brightness steps down to the Main3 mode 40 60 seconds afterwards the brightness increases to the Maximum mode again This stepping goes cyclically to maintain the user s safety and the flashlight s functionality In the conditions of good air cooling the flashlight delivers constant light even in Maximum mode It does not use timers but real active temperature measurements Do not use different power sources together i e old ones with new ones charged with discharged Do not use different types of batteries combined as the element with less p capacity can be damaged 5 Do not modify or recast the flashlight and its components as it will deprive you of the 1 Always follow the instructions from this manual and recommendations on battery usage 2 Apply only the recommended power sources 3 Donotreverse battery polarity 4 warranty 6 Donotallow water or any other liquid to leak into the flashlight H O AN 7 Do not aim a turned on flashlight at people s or animals eyes it can cause temporary blindness 8 Donotallow children to use the flashlight without your assistance J Armytek Optoelectronics Inc shall not be liable for any harm done to the user if it was caused by improper use of the product It is recommended to clean the threads and O rings off dirt and old grease Rememb
4. ate with batteries in use new and quality batteries store the flashlight in acceptable for batteries operational temperature and revise the batteries state at least once a month If you have noticed any signs of batteries defects withdraw them from the flashlight and take out of operation It is also recommended to replace discharged batteries with new ones before the storage as the chance of leakage is higher with discharged batteries Click x2 Press amp Hold Main The flashlight has 4 Sections of modes Section1 Firefly modes Section2 Main modes A eg EA ji ee Section3 Maximum Section4 Special modes Main Firefly Main3 In OFF state Bre Click To turn on the last used mode Firefly Main or Maximum If the Click x2 Press amp Hold mey flashlight was turned on in one of the Special modes it will turn on in the last Main Firefly OFF Firefly used Main mode Firefly Main s i i i Firefiy1 gt Firefly2 Press and hold To turn on Firefly1 mode in Section 1 R e In ON state Firefly3 for C2 P slit bad Click To turn off the flashlight Click x3 Press amp Hold Maximum Press and hold To start cycling through the modes of the current Section In OFF Max Main1 gt Main2 Maximum mode it starts cycling through the Main modes in Section 2 Any mode Max iia The same in OFF amp ON states 2 clicks To turn on the last used Main mode Section 2 Further double clicks Click x4 Press amp Hold Special will switch modes
5. ding the exposure of liquid from defected batteries 5 Usage of low quality batteries Armytek Optoelectronics Inc Web www armytek com Email service armytek com Address 67 Vandervoort Dr Richmond Hill Ontario L4E 0C7 Canada Specifications are subject to change without notice a BORN TO EXCEED THE MOST TECHNICALLY ADVANCED FLASHLIGHTS IN THE WORLD DIUJI V id USER MANUAL 0 gt gt gt WtrOV tevavnPr YY Armytek Optoelectronics Inc is a Canadian manufacturer that produces powerful and reliable flashlights designed especially for your needs applying in them components made in the USA and Japan 10 years no hassle warranty Superb light of amazing constant brightness due to powerful electronics and active temperature control without timers Efficient TIR optics and no tunnel vision effect even after continuous use Multicolor Warning Indication of low battery level and high temperature Side switch for comfortable one hand operation and easy modes switching with advanced operation Multicolor State Indication and ultra low current drain in OFF state more than 25 years Removable magnet in the tailcap firm holster removable clip strong lanyard and possibility of tail stand for multipurpose use Compact and light weight flashlight of guaranteed durability stands up harsh impacts and falling from 10 meters Total protection from water dirt and dust penetration flashlight continue
6. er that secure protection from water and dust cannot be provided by worn out sealing And fouling as well as lack of lubricant cause fast wear out of threads and sealing rings To clean the threads do the following 1 Unscrew the tailcap and remove the sealing ring carefully with a toothpick do not use sharp metal things as they can damage the ring 2 Wipe the sealing ring thoroughly with a soft cloth or tissue Do not use solvents If the sealing ring is worn out or damaged replace it by anew one 3 Clean the metal threads with a brush using ethanol Be careful not to allow applied liquid to get inside the flashlight or tailcap as it can cause fails in functionality of the flashlight After cleaning lubricate the thread and the sealing ring with polyalphaolefin based silica grease e g Nyogel 760G The application of automotive and other improper grease can cause swelling and damage of the sealing rings In case of active operation and exploitation in dusty environments it is recommended to perform cleaning and lubricating of the parts as often as required even if itis more than twice a year Armytek provides free warranty repair for 10 years from the purchase Warranty doesn t cover damage caused by 1 Improper usage 2 Attempts to modify or repair the flashlight by nonqualified specialists 3 Longtime application in chlorinated or polluted water or other liquids other than water 4 High temperatures and chemicals exposure inclu
7. he small cover at the end of the tailcap and put the magnet out Specifying the battery type for correct voltage indication Do not specify the type of power source manually unless you use unprotected Li lon batteries different from those that are stated by default 1xAA for A1 Pro 2xAA for A2 Pro 1xCR123A for C1 Pro 1x18650 Li lon for C2 Pro Press amp Hold Release amp Click 1xAA Click x1 x2 or x3 O 1xCR123 1x18650 Li lon O 2xAA 2xCR123A 1x14500 Li lon amp 1xRCR123 Li lon 2xRCR123 Li lon To access the Menu press and hold the switch button when the flashlight is switched off It will switch on go through the all available modes and then switch off again After switching off release the button quickly and click it rapidly again The flashlight will enter the Menu and the LED will flash about 3 times a second Now you can specify the battery type 1 click for 1xAA A1 Pro 1xCR123A C1 Pro 1x18650 Li lon 2 clicks for 2xAA A2 Pro 2xCR123A C2 Pro 3 clicks for 1x14500 Li lon A1 Pro 1xRCR123 Li lon C1 Pro 2xRCR123 Li lon C2 Pro After the choice is made the light will flash 1 2 or 3 times to show the battery type chosen We recommend NOT to leave power sources inside the flashlight for a long storage period as batteries especially non rechargeable can leak for various reasons and damage the inner parts of the flashlight If you want to keep your flashlight in a stand by st
8. lashlights with Warm light are about 7 less beam distances are about 3 less 2 Pro in Max mode Full stabilization is for 20 minutes then itis Step We recommend to use Sanyo Eneloop AA rechargeable batteries instead of ordinary AA batteries to obtain higher brightness and longer runtimes Prime C2 Pro 1050 8800 206 yards 188 meters Firefly1 0 2Im 100d Firefly2 2lm 18d Firefly3 151m 72h Maint 70Im 18h Main2 200Im 9h Main3 420Im 3 8h Max 10501m 1 5h Strobe 10Hz Warning 0 6Hz 1x18650 Li lon 2xCR123A 2xR123 Li lon Length 4 73 120mm body diameter 0 96 24 5mm 2 1902 62g Items included in the package Flashlight Lanyard Holster 2spare O rings Magnet Clip User manual Prime 7 r v Depending onthe model your flashlight can inconsiderably differ from the pictures in the manual v The producer reserves the right to change the package at his own discretion without modifying this manual To set replace batteries 1 Unscrew the tailcap 2 Place the batteries with the positive contact facing the head of the flashlight 3 Adjust the tailcap and tighten it as far as it can go The flashlight is ready for operation The removable magnet in the tailcap With its help you can easily attach the flashlight to an electric service panel a bike handlebar above a car wheel etc The magnet can be taken out of the tailcap To do this unscrew t
9. retly2 Maximum 3 clicks from OFF or ON state turn on the Maximum mode Special modes Strobe Beacon 4 clicks from OFF or ON state turn on the last used Special mode Strobe Beacon Cycling through modes In ON state press and hold the button in any mode the modes of the current Section will start switching cyclically Release the button to select the desired mode In Maximum mode it starts cycling through the Main modes Automemorizing After switching off the last used Mode is memorized for quick 1 click access at next switching on If the flashlight was turned on in one of the Special modes it will turn on in the last used Main mode Lock out function Unscrew the tailcap to 1 4 for the protection from accidental switching on State indication will be turned off Multicolor State Indication Shows the battery level by short flashes every 5 seconds C2 Pro has State Indication in OFF state and Firefly modes which can be helpful to find the flashlight in the dark Other models don t have it Switching Multicolor State Indication ON OFF C2 Pro It is switched off by default in OFF state and Firefly modes To turn on and off unscrew the tailcap to 1 4 press the button and holding the button pressed tighten the tailcap and then unscrew it again The settings will be memorized even when battery is changed Warning Indication In ON state shows the battery level and the temperature inside the flashlight Low battery level When it is lt
10. s to work even at the depth of 10 meters Model LED Optics Brightness stabilization type Light output OTF lumens Peak beam intensity candelas Hotspot spill Beam distance Hotspot diameter at 330 feet 100 meters Modes and runtimes measured for Sanyo Eneloop AA 2000 mAh Armytek CR123A 1500 mAh Armytek 18650 Li lon 3100 mAh to the decrease to 10 of initial brightness Recommended power source Size Weight w o batteries Prime A1 Pro 370 3050 120 yards 110 meters Firefly1 0 15Im 90d Firefly2 1 7lm 200h Main1 10 Im 25h Main2 70 Im 3h Main3 210 Im 1 2h Max 370 Im 30min Strobe 10Hz Warning 0 6Hz 1xAA 1x14500 Li lon Length 4 14 105mm body diameter 0 96 24 5mm 2 2202 63g Prime A2 Pro Prime C1 Pro Cree XM L2 FULL stabilization constant brightness 500 4250 400 3100 20 80 142 yards 130 meters 121 yards 111 meters 16 meters Firefly1 0 151m 130d Firefly2 1 71m 300h Maint 10 Im 48h Main2 70 Im 9 5h Main3 210 Im 2 5h Max 500 Im 1h Strobe 10Hz Warning 0 6Hz 2xAA Length 5 95 151mm body diameter 0 96 24 5mm 2 2602 64g Firefly1 0 151m 130d Firefly2 1 7lm 300h Maint 10 Im 40h Main2 70 Im 5h Main3 210 Im 2h Max 400 Im 35min Strobe 10Hz Warning 0 6Hz 1xCR123A 1xR123 Li lon Length 3 50 89mm body diameter 0 96 24 5mm 2 050z 58g Light outputs for f
Download Pdf Manuals
Related Search