Installation and User`s manual - Esse-ti
Contents
1. Helpy Vox ST56 Helpy Star e GSM Combi Board For the correct operation of the module a standard SIM Card is required This manual describes the GSM200 installation procedure For other instructions please refer to the elevator alarm system user manual or to the GSM Combi user manual Page 6 INSTALLATION gt Remove the cover oup a 00 ANTENNA connector LED indicating signal strength green and LED indicating device operation status red SIM CARD housing RJ45 for module connection to Esse ti elevator alarm systems or GSM Combi board Page 7 Inserting the SIM card Before inserting or replacing the SIM card always make sure that the module has been disconnected from the mains and that no electrostatic discharge is present in order to avoid damaging it Take all necessary measures to avoid electrostatic discharge gt Shift the SIM card housing cover upward and lift it gt Carefully slide the SIM card in its housing cover gt Lower the SIM card housing cover and shift it downward until it blocks WARNING The SIM Card must have the PIN code DISABLED If the Sim card has the PIN Code enabled it is necessary to disable it by means of a normal mobile phone gt Close the module cover Inserting the antenna gt Screw the antenna in to the connector on the top of the module WARNING NEVER connect GSM200 module without having installed the antenna The module2. a gloNet a Slereies a Certificato n 9110 ESTI TELECOMUNICAZIONI UNI EN ISO 9001 2008 Installation and User s manual CE Thank you for choosing an Esse ti product This product has been especially designed for easy operation It has been manufactured with perfect workmanship using suitable materials for long lasting performance All Esse ti products are subjected to extensive reliability and operational testing in our laboratories in order to provide total guarantee for the user The User shall be responsible for defects arising from the use of the product Esse ti shall only be responsible for defects according to and within the limitations set by the Presidential Decree dated 24 05 1988 no 224 fulfilling the EEC directive no 85 374 on the harmonisation of statutory and administrative regulations of the Member States on the liability for damages arising from defective products under art 15 of Law no 183 of 16 April 1987 Esse ti reserves the right to modify the characteristics of the products at any time without prior notice TABLE OF CONTENTS GENERAL INSTRUCTIONS FOR THE INSTALLER 4 General Notes esssssascss cs estiro tEn aE Easa aia 4 Making the Installation 0 00 ed DESCRIPTION hreier rine 16 INSTALLATION iT Inserting the SIM cafdo err ae EE EE RE 8 Inserting the antenna eceesceeseeseseeseeeeseeeseseesceeeseeeeseeeceeaceeeaeeeeaeeees 8 PROGRAMMING a CONNECTI
3. ED Normal operation 0 1 2 3 4 5 LED indicating GSM signal strength GREEN No signal 1 2 3 4 5 Low signal level ii Medium signal level i High signal level s Page 15 GSM200 Rel dated 25 03 2015
4. L Helpy Vox are positioned towards the RJ 45 connector Page 10 gt Insert the provided cable pin to pin cable in to the two RJ45 connectors located on the ST60 ST61 Helpy Quick Helpy Quick TL Helpy Vox and GSM200 module In order to reach longer distances up to 100m please use a cat 5 or higher cable ST56 Helpy Star gt Make sure that on the ST56 Helpy Star jumpers are inserted in the larger connector for optional PSTN line board gt Insert the provided cable pin to pin cable in to the two RJ45 connectors located on the ST56 Helpy Star and GSM200 module In order to reach longer distances up to 100m please use a cat 5 or higher cable GSM Combi board gt In order to connect the GSM200 module to the GSM Combi board refer to the GSM Combi board s instruction manual Note when connected to the GSM Combi board the green LED indicating signal strength located on the GSM200 module is not working To check the signal strength check the LED located on the connection board provided with the GSM Combi CT 624 or the LED located ont he GSM Combi board POLARIS SMILE FOX Page 11 STARTING gt After the connection make sure that the red LED indicating the device operation status located on the GSM200 module is switched on and stays lit for a few seconds before it starts blinking In case the red LED should not be blinking the GSM module would not be correctly registered to the GSM
5. M200 module onto the two screws Page 13 GSMZ200 installation recommendations The module is provided with a 3m cable Use a cat 5 or higher cable to connect the GSM200 module at a longer distance up to 100m The minimum recommended distance between the GSM200 module and the elevator alarm system is 50cm The GSM200 module must be installed in a location where the radio signal allows for using the GSM system It is advisable to leave plenty of space around the module for maintenance operations Do not lay the connection cable near the 230Vac mains Do not install the GSM200 module outdoors since it lacks protection devices against weather conditions that can damage the module water humidity etc Do not install the GSM200 module near electronic radio or TV sets Personal Computers wired radio systems etc or magnetic credit cards floppy disks etc devices that could be subjected to RF interference from the module recommended distance from the antenna is min 2 5m Do not install the GSM200 module near medical devices Its operation may cause damage to hearing aids or pacemakers Always make sure that the device operation is permitted in the place of installation i e installation is not allowed in hospitals airplanes etc WARNING To ensure proper operation it is recommended not to mount GSM200 module next to metal surfaces Page 14 SIGNALLING LED indicating device operation status R
6. ONS wi ss3 ctssnes resin E E E aeris 10 Helpy L300 Helpy L300 TL 10 Helpy L200 Helpy L200 TL eeseseseeeneeeeees 10 ST60 ST61 Helpy Quick Helpy Quick TL Helpy Vox ST56 Helpy Star GSM Combi board all STARTING ee 12 LOSt Call ccs sscsvesssszzecseasestecssdssveaageiases n A E A a emo a tae 13 Module mounting operations cecceeseeceseeeeseeseseeeeseeseeeeseeeeaeeeeseeeeaes 13 GSM200 installation recommendations soak SIGNALLING sinartanan i 1S LED indicating device operation status RED sD LED indicating GSM signal strength GREEN cee 15 GENERAL INSTRUCTIONS FOR THE INSTALLER GENERAL NOTES Carefully read the notes contained in this section as they provide important information on the correct safe installation use and maintenance of the product The product must be EXCLUSIVELY used for the purpose it was designed for Esse ti shall not be responsible for damages arising from improper use e The product has been designed in compliance with the regulations in force and must be installed in systems that comply with the provisions of law e Always disconnect the product from the power supply mains before carrying out any operation either inside or outside the product cleaning maintenance etc e Always refer to an authorised assistance centre for repair e Install the product in a well ventilated place making sure not to obstruct the ventilation slots e Bewar
7. e of symbols showing lightening with arrow inside a triangle since they indicate the presence of dangerous voltage e Beware of symbols showing an exclamation mark inside a triangle since they indicate potentially dangerous or even lethal situations that require utmost attention Do not use the product in association with other electric or electronic devices that were not especially designed to be used with it e Do not install the product in potentially explosive environments e Make sure that the product has been installed as required Page 4 Do not introduce objects liquids or powders inside the product Do not use sprays inside the product e Do not open the product case since it does not contain any user serviceable parts If necessary contact an authorised assistance centre Packing components such as plastic bags foam polystyrene etc must be kept out of the reach of children because potentially dangerous MAKING THE INSTALLATION Internal telephone installations must be carried out by specialised personnel The installation and connection of telephone terminals to the telecommunications network that do not comply with the regulations in force is not permitted Page 5 DESCRIPTION The GSM200 module can be used in conjunction with the following Esse ti devices e Elevator alarm systems Helpy L300 Helpy L300 TL Helpy L200 Helpy L200 TL ST60 ST61 Helpy Quick Helpy Quick TL
8. may damage Page 8 PROGRAMMING When using the GSM200 module for connection with any Esse ti alarm system please make sure the parameter Programming the type of telephone line has been adequately set in the specific alarm system gt gt Vv Lift the local telephone handset of the elevator alarm system Dial lt Installer password gt by default ceo Set the type of GSM200 line Exit programming lt Installer password gt by default ceo Page 9 CONNECTIONS Helpy L300 Helpy L300 TL gt Make sure that the jumpers JP11 and JP12 located on the Helpy L300 Helpy L300 TL are in position 2 3 towards the RJ45 connector gt Insert the provided cable pin to pin cable in to the two RJ45 connectors located on the Helpy L300 Helpy L300 TL and GSM200 module In order to reach longer distances up to 100m please use a cat 5 or higher cable Helpy L200 Helpy L200 TL gt Make sure that the jumper JP5 located on the Helpy L200 Helpy L200 TL is in position 2 3 towards the RJ45 connector gt Insert the provided cable pin to pin cable in to the two RJ45 connectors located on the Helpy L200 Helpy L200 TL and GSM200 module In order to reach longer distances up to 100m please use a cat 5 or higher cable ST60 ST61 Helpy Quick Helpy Quick TL Helpy Vox gt Make sure that the two jumpers located near the RJ45 connector on the ST60 ST61 Helpy Quick Helpy Quick T
9. network provider Disconnect the GSM200 and make sure that the SIM card has been correctly inserted and no PIN is on For a correct registration of the GSM200 module you must wait 1 minute s time gt Check the signal strength by means of the green LED located on the GSM200 module see paragraph Signalling Note the signal strength is also indicated by the specific LED located on the elevator alarm system Note when connected to the Helpy L200 Helpy L200 TL the green LED signal strength located on the GSM200 module is not working Check the signal strength by means of the LED indicating the device operation status located on the Helpy L200 Helpy L200 TL see the Helpy L200 Helpy L200 TL user manual gt Ifthe signal strength is good proceed with a test call and mounting operations see the following paragraphs Page 12 Test call 5 gt gt Lift the local telephone handset of the elevator alarm system Dial lt Installer password gt by default 0 H dialing tone Dial 0 dialing tone Dial x telephone number Note wait about 10 seconds after dialling the desired telephone number before a confirmation tone indicates that the call has been forwarded Module mounting operations gt Drill two holes with 5mm diameter on the wall at a distance of 50mm Insert the 2 fischers and screw down until the screws are at a 5mm distance from the wall Place the GS
Download Pdf Manuals
Related Search