Outdoor Mini Dome & Outdoor Mini Fisheye Dome Hardware Manual
Contents
1. 9 Close the dome cover 30 pd ACTI _ Connecting Vision Hardware Manual Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera from your PC both the camera and the PC have to be within the same network segment In most cases it means that they both should have very similar IP addresses where only the last number of the IP address is different from each other There are 2 different approaches to IP Address management in Local Area Networks by DHCP Server or Manually Using DHCP Server to Assign IP Addresses If you have connected the computer and the camera into the network that has a DHCP server running then you do not need to configure the IP addresses at all both the camera and the PC would request a unique IP address from DHCP server automatically In such case the camera will immediately be ready for the access from the PC The user however might not know the IP address of the camera yet It is necessary to know the IP address of the camera in other to be able to access it by using a Web browser The quickest way to discover the cameras in the network is to use the simplest network search built in the Windows system just by pressing the Network icon all the cameras of the local area network will be discovered by Windows thanks to the UPnP function support of our Cameras In the example below we successfully found the camera that we had just con2. Outdoor Mini Dome amp Outdoor Mini Fisheye Dome Hardware Manual E918 E918M E919 E919M E920 E920M E921 E921M E922 E922M E923 E923M Ver 2014 10 06 ACTI Connecting Vision lt da Hardware Manual Table of Contents Precautions 4 Safety Instructions annette 6 Introduction 7 LIST Or MOOGI Sosina earn ajana aaa a aaa ajaa aaa aana ajaa 7 Package CGONlENIS isasasasasa rana sangan Nani nani dangan adang imaina inanim NANGN ANNA 9 Physical Description naaar neanenanennennennsnnnennennennsnanennense 10 EOS E20 EIL nennen ennen 10 E919 E921 E923 nennen eenen enen nen enen nen enen neneenenenen 10 E918M E920M E922M nennen enrenenenreneneenenenen 12 EO TOM E92 IMV BOZO ass aia aa ei a akih a ka a Ba ak a ka a Pala Ka ak kai 12 Mounting ODMOINS rirse rsa aaa aaa anna aa aaa ag aia ag agak aaa aaa aaa aaa a 14 Installation Procedures 15 Step 1 Prepare for Installation annen menne nennenennenenn 15 Step 2 Open the Dome Cover nanne nennen menne nenenen 16 Step 3 Route the Cables naeve menne nennenennenen 17 Step 4 Install the Camera nennen menen menne nennn menne nenn 18 Step 5 Waterproof the Cable Connection aen 19 M12 Ethernet Cable for E9xxM models only anana aaa anan ane 19 RJ 45 Ethernet Cable for E9xx models only cccceeeeeeeeeees 20 Step 6 Connect to Network neemen menne neenenenn 23 Step 7 Access the Camera Live VieW en anenmenn 23 Step 8 Clo
3. 00018 00 0F 7C 0D 68 C1 A1D 500 V6 07 10 AC Megapixel IP Dome 172 16 26 43 E923 A XX 14D 00018 00 0F 7C 00 68 05 A1D 500 V6 07 10 AC Hemispheric Camera 172 16 26 79 E923 A XX 14D 00019 00 0F 7C 0D 68 D6 A1D 500 V6 07 10 AC Hemispheric Camera 172 16 26 38 172 16 26 123 E923MA XX 14D 00018 E94 A XX 131 00054 00 0F 7C 0D 68 E9 00 0F 7C 0B AE 50 A1D 500 V6 07 10 AC A1D 500 V6 07 07 AC Hemispheric Camera Megapixel IP Dome 172 16 26 141 E97 A XX 13K 00147 00 0F 7C 0C 60 9A A1D 500 V6 05 23 AC Megapixel IP Dome OL LIL LLL LIL LIL LL LLL 172 16 26 36 E938 A XX 14D 00018 00 0F 7 00 64 6B A1D 500 V6 07 10 AC Hemispheric Camera 172 16 26 129 ECD1000 A 13J 00177 00 0F 7C 0C 0E 1B ECD 010 V1 01 05 AC 9 CH Embedded Camera Decoder er O Add Remove You can quickly see the camera model in the list Click on the IP address to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already 32 ACTI Connecting Vision DM Hardware Manual Using the Default Camera IP Address If there is no DHCP server in the given network the user may have to assign the IP addresses to both PC and camera manually to make sure they are in the same network segment When the camera is plugged into network
4. default HTTP port of the camera is 80 which can be omitted from the address for convenience hee Web Configurator x Web Configurator Account Password Language English x Login Reset Before logging in you need to know the factory default Account and Password of the camera Account Admin Password 123456 36 ACTI Connecting Vision Ds Copyright 2014 ACTi Corporation All Rights Reserved 7F No 1 Alley 20 Lane 407 Sec 2 Ti Ding Blvd Neihu District Taipei Taiwan 114 R O C TEL 886 2 2656 2588 FAX 886 2 2656 2599 Email sales acti com
5. 00377 000 Drill cable hole within this block Drill Hole Drill Hole Drill Template scale 1 1 Drill Hole 2 Route the cable from the network side through the hole and connect it to the Ethernet port of the camera NOTE If the camera will be installed outdoors or in places wherein environmental factors change drastically make sure to waterproof the cable connection see Step 5 Waterproof the Cable Connection on page 19 for instructions 3 Push the cable through the the hole on the surface If the cable will be routed along the surface 1 Pull the tab to slide it off from the dome cover 2 Route the camera cable through the gap on the camera cover 17 ACTI Connecting Vision DA Hardware Manual Step 4 Install the Camera 1 If necessary insert a memory card into the memory card slot of the camera See How to Insert the Memory Card on page 25 for more information 2 Install the camera to the surface using the three 3 bundled screws NOTE Please make sure the screw is flat on the plate 18 DM ACTi Connecting Vision Hardware Manual Step 5 Waterproof the Cable Connection Depending on the camera model the Ethernet cable or the pigtail of the camera may either have the RJ 45 or M12 connector M12 Ethernet Cable for E9xxM models only Typical M12 Ethernet cable has waterproof connection Simply connect and screw the cable co
6. 22 RA ACT Hardware Manual Step 6 Connect to Network Connect the other end of the network cable to a switch or injector Then connect the switch or injector to a network or PC and a power source See Power over Ethernet PoE example connection diagram below Ethernet Cable Ethernet Cable Data Ethernet Cable Data Power AC Power Source Camera Step 7 Access the Camera Live View See Accessing the Camera on page 31 for more information on how to access the Live View of the camera 23 ACTI Connecting Vision da Hardware Manual Step 8 Close the Dome Cover 1 Align cable tab side of the dome cover to the direction of the network cable 2 Tighten the three 3 screws using the supplied hex screwdriver to attach the dome cover 3 Remove the thin film Final installation should look similar to the illustration below 24 pd ACTI _ Connecting Vision Hardware Manual Other Adjustments and Accessories How to Install Remove the Memory Card How to Insert the Memory Card 1 Loosen the three 3 screws to remove the dome cover 2 Insert the memory card into the card slot with the metal contacts facing the bottom side of the camera 3 Push the card completely until it clicks into place 4 Attach the dome cover to the camera and tighten the three 3 screws How to Remove the Memory Card In case th
7. 28 5 6 1 A 172 16 26 57 00 0F 70 04 87 AID 310 V4 12 09 Video Server TCD2100 228 5 6 1 A 172 16 26 61 00 0F 7C 04 32 E3 A1D 310 V4 12 09 AC Megapixel IP Camera TCM1231 228 5 6 1 With the procedure shown above all the cameras will have unique IP addresses starting from 192 168 0 101 In case there are 20 cameras selected the last one of the cameras would have the IP 192 168 0 120 Later by pressing the Refresh button of the IP Utility you will be able to see the list of cameras with their new IP addresses Please note that it is also possible to change the IP addresses manually by using the Web browser In such case please plug in only one camera at a time and change its IP address by using the Web browser before plugging in the next one This way the Web browser will not be confused about two devices having the same IP address at the same time M el pd ACTI Connecting Vision Hardware Manual Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the same network segment it is possible to use the Web browser of the PC to access the camera You can use any of the browsers to access the camera however the full functionality is provided only for Microsoft Internet Explorer The browser functionality comparison er Na Na ive video wrea nesae Ove Video overlay based configuration Motion Detection regions Privacy Mask
8. Group Choose homegroup and sharing options Internet Options Access files and printers located on other network computers or change sharing settings Windows Firewall btocol Version 4 TCP IPv4 Properties La jm slm ino Connect using uy Intel R 82567LM 3 Gigabit Network Connection You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically This connection uses the following items m Use the following IP address M 0 Client for Microsoft Networks M J VirtualBox Bridged Networking Driver IP address 192 168 0 99 Subnet mask Lis ZN s AE 0 Default gateway Obtain DNS server address automatically Use the following DNS server addresses Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Preferred DNS server Alternate DNS server E validate settings upon exit OK Cancel 33 ACTI Connecting Vision DA Hardware Manual Manually adjust the IP addresses of multiple cameras If there are more than 1 camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of the
9. and it does not detect any DHCP services it will automatically assign itself a default IP 192 168 0 100 Whereas the default port number would be 80 In order to access that camera the IP address of the PC has to be configured to match the network segment of the camera Manually adjust the IP address of the PC In the following example based on Windows 7 we will configure the IP address to 192 168 0 99 and set Subnet Mask to 255 255 255 0 by using the steps below BE lt lt All Control Panel items Network and Sharing Center lt Network and Internet gt Network Conne con Pane ES Organize v Disable this network device Diagnos x Local Area Connection ll View your basic network information and set up connections Change adapter settings Ae Jo bed See full map ma Change advanced shari zendende and SISO_NP_PC1 Network Internet Network re This computer 4 Intel R 8 Disable View your active networks Connect or disconnect Status Diagnose Jo Network Access type Internet Work network Connections Local Area Connection R Bridge Connections Create Shortcut Change your networking settings Set up a new connection or network x Delete Set up a wireless broadband dial up ad hoc or VPN connection or set up a router or la Rename access point Connect to a network ae Connect or reconnect to a wireless wired dial up or VPN network connection ee also Home
10. ditional accessories required for installation E9xx Models E9xxM Models Exterior grade Ethernet Cable with Exterior grade Ethernet Cable with RJ 45 connector not included can be Waterproof M12 Male Connector purchased from local stores D coding and PoE type A not included can be purchased from local stores Bundled Cable Gland 2 Depending on the material of the surface where the camera will be installed it may be necessary to drill the three 3 screw holes and use the supplied screw tox In this case attach the bundled drill template on the surface and drill the screw holes R506 00377 000 4 eel Drill ac Drill Hole Drill Template scale 1 1 Drill Hole 15 ACTI Connecting Vision da Hardware Manual Step 2 Open the Dome Cover 1 Loosen the three 3 screws using the bundled hex screwdriver 2 Lift to remove the dome cover NOTE e The dome cover is attached to the camera body by a string do not abruptly lift the dome cover e Adesiccant bag is attached underneath the dome cover DO NOT remove the desiccant bag to keep the camera interior parts dry 16 ACTI Connecting Vision da Hardware Manual Step 3 Route the Cables Determine whether the cable will pass through a hole on the surface or be routed along the surface If the cable will pass through a hole on the surface 1 Drill the hole for the cable on the surface R506
11. ect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Warning Changes or modifications to the equipment that are not expressly approved by the responsible party for compliance could void the user s authority to operate the equipment European Community Compliance Statement C 4 This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to European Standard EN 55022 and EN 55024 In a domestic environment this product may cause radio interference in which cause the user may be required to take adequate measures D4 ACTi Connecting Vision Hardware Manual Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards Water and Moisture Do not use this video product near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like Don t use accessories not recommended by the manufacturer Only install this device in a dry place protected from weather Servicing Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to q
12. ere is a need to remove the card make sure to access the camera Web Configurator to safely unmount the card first see the camera Firmware User s Manual for more information Once unmounted from the firmware push the card to eject it from the slot 29 ACTI Connecting Vision da Hardware Manual How to Adjust the Fisheye View Orientation for E919 E921 E923 only 1 Open the dome cover 2 Loosen the three 3 screws securing the lens 3 Turn the lens to adjust the viewing orientation The arrow on the lens indicates the top side orientation 5 Close the dome cover 26 D4 ACTi Connecting Vision Hardware Manual How to Connect Audio In Device The camera comes with an audio jack where an audio input device such as a microphone with a built in amplifier can be connected The audio in jack is covered by a rubber protection WARNING Do not remove this rubber protection if the audio in jack will not be used to avoid water or dust from entering the jack To connect an audio input device do the following 1 Pull to remove the rubber protection 2 Connect the audio input device Audio Input Jack Audio Device NOTE The microphone must have a built in amplifier Connecting an ordinary microphone will dwarf sounds and will result in inaudible recording 3 Ifthe camera is installed outdoors be sure to wrap the audi
13. ision DA Hardware Manual Physical Description E918 E920 E922 E919 E921 E923 Item Description System LEDs Indicates the camera status Amber LED Blinks when network activity is in progress Blue LED Lights up when the camera is powered up and goes off again after the boot up process is complete Green LED Lights up when the camera is connected to a network ACTI Connecting Vision DA Hardware Manual Item Description Audio Input Connects to audio input devices such as a microphone with built in amplifier etc See How to Connect Audio In Device on page 27 for more information NOTE The microphone must have a built in amplifier Connecting an ordinary microphone will dwarf sounds and will result in inaudible recording Ethernet Port Connects to a network using an Ethernet cable with RJ 45 RJ 45 connector Reset Button Restores the factory default settings of the camera To reset the camera while the power is on press and hold the Reset Button for at least 5 seconds or until the Blue LED lights up Memory Card Slot Insert a memory card not included into the slot for local recording purposes See How to Install Remove the Memory Card on page 25 for more information NOTE Supports only microSDHC and microSDXC cards 11 ACTI Connecting Vision da Hardware Manual E918M E920M E922M E919M E921M E923M Item Description System LEDs I
14. ll servicing to qualified service personnel Trademarks All names used in this manual are probably registered trademarks of respective companies Liability Every reasonable care has been taken during the writing of this manual Please inform your local office if you find any inaccuracies or omissions We cannot be held responsible for any typographical or technical errors and reserve the right to make changes to the product and manuals without prior notice D4 ACTi Connecting Vision Hardware Manual Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a class B C digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Conn
15. m all of the cameras would then have the initial IP address of 192 168 0 100 which is not a proper situation for network devices all the IP addresses have to be different from each other The easiest way to assign cameras the IP addresses is by using IP Utility IP_Utility IP Address NetMask 172 16 26 192 255 255 255 0 Basic Search T Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Reset Save amp Reboot rose A veren NN 1 IP Address MAC Address FW Version Model Serial No Multicast IP Status NA vuur x A O9 11 Ue emispneric Lamera Liv i JO 4 A 172 16 26 2 00 0F 7C 07 DE 65 A1D 311 V5 07 05 AC Hemispheric C KCM3911 228 5 6 1 a A 172 16 26 4 00 0F 7C 08 17 C2 A1D 310 V4 12 02 AC Mega IP Camera TCM1111 228 5 6 1 172 16 26 6 00 0 KCM7311 228 5 6 1 Change Network Address Ss A 172 16 26 7 00 0 TCM6630 228 5 6 1 A 172 16 26 10 00 Dynamic IP Address TCM4201 228 5 6 1 A 172 16 26 11 00 4 KCM3911 228 5 6 1 A 172 16 26 13 oo d Static IP Address KCM5111 228 5 6 1 F WA 172 16 26 40 00 0 KCM5211 228 5 6 1 Starting IP Address g Ci 172 16 26 41 00 0 KCM5311 228 5 6 1 A 172 16 26 50 00 0 Netmask KCM5111 228 5 6 1 A 172 16 26 52 00 0 KCM5311 228 5 6 1 A 172 16 26 53 00 0 nana TCM5311 228 5 6 1 Er A 172 16 26 54 00 0 TCM5611 228 5 6 1 A A 172 16 26 55 00 0 pply TCM5111 2
16. ndicates the camera status Amber LED Blinks when network activity is in progress Blue LED Lights up when the camera is powered up and goes off again after the boot up process is complete Green LED Lights up when the camera is connected to a network Item Audio Input Ethernet Port M12 Reset Button Memory Card Slot ACTI Connecting Vision DA Hardware Manual Description Connects to audio input devices such as a microphone with built in amplifier etc See How to Connect Audio In Device on page 27 for more information NOTE The microphone must have a built in amplifier Connecting an ordinary microphone will dwarf sounds and will result in inaudible recording Connects to a network using an Ethernet cable with M12 connector The camera uses the female M12 connector with D coding and PoE type A Restores the factory default settings of the camera To reset the camera while the power is on press and hold the Reset Button for at least 5 seconds or until the Blue LED lights up Insert a memory card not included into the slot for local recording purposes See How to Install Remove the Memory Card on page 25 for more information NOTE Supports only microSDHC and microSDXC cards 13 ACTI Connecting Vision da Hardware Manual Mounting Options Select the most suitable solution for your installation environment The camera can be mounted by either of the following methods Mou
17. nected to the network gt th gt Network gt et nn E Organize v Search Active Directory Network and Sharing Center Add a printer Add a wireless device VW Favorites 5 Ti ME Desktop ECD 1000 ECD 98 A XX 14D 00018 E97 A XX 13K 00147 mn a a B Downloads Recent Places el os ei E94 A XX 13 1 00054 E923 A XX 14D 00019 E922MA XX 14D 00018 Libraries z 922 A XX 14D 00018 4 E921MA XX 14D 00018 4 E921 A XX 14D 00018 Computer Ga Network IM 921 A xx 14D 00012 IM Eor A XX 138 00154 E919MA XX 14D 00008 85 items 919 A XX 14D 00008 i E918MA XX 14D 00018 4 E918 A XX 14D 00018 31 Hardware Manual ACTI Connecting Vision DM By double clicking with the left mouse on the camera model it is possible to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already lf you work with our cameras regularly then there is even a better way to discover the cameras in the network by using IP Utility The IP Utility is a light software tool that can not only discover the cameras but also list lots of valuable information such as IP and MAC addresses serial numbers firmware versions etc and allows quick configuration of multiple devices at the same time The IP Utility can be downloaded for free from With just one click you can launch the IP Utility and the
18. ni Dome with Basic WDR M12 connector E920M Fixed lens E921 5MP Outdoor Mini Fisheye Dome with Basic WDR Fixed lens SMP Outdoor Mini Fisheye Dome with Basic WDR M12 connector Fixed lens E921M E922 10MP Outdoor Mini Dome with Basic WDR Fixed lens 10MP Outdoor Mini Dome with Basic WDR M12 connector E922M Fixed lens 10MP Outdoor Mini Fisheye Dome with Basic WDR Fixed lens E923 Pp ACTI Connecting Vision Hardware Manual 10MP Outdoor Mini Fisheye Dome with Basic WDR M12 connector Fixed lens From the installation perspective the above models are very similar therefore one manual is used for all of them ACTI Connecting Vision DA Hardware Manual Package Contents Check if the camera package comes with the following items Camera Camera E918 E918M E920 E920M E922 E922M E919 E919M E921 E921M E923 E923M Screw Kit Drill Template Drill Template Cable Gland Hexagon Screwdriver Not available in E9xxM models Quick Installation Guide Warranty Card a Hardware Warranty Policy p4 acti IMPORTANT When the camera is taken out from the box the lens cover is covered by a thin film DO NOT remove this film It is used to protect the lens cover from scratches or fingerprint marks which may happen during installation Remove this film only after the camera is securely installed i ne and all connections are complete ACTI Connecting V
19. nnectors to make the connection waterproof Make sure the connectors are secured tightly 19 V ape ACTI Connecting Vision Hardware Manual RJ 45 Ethernet Cable for E9xx models only When using the RJ 45 Ethernet cable follow the procedures below to waterproof the cable connection 1 Detach the cable gland as shown below Gland Body Clamping Nut Sealing Rubber and Claw 2 On the network side cable insert the clamping nut through the Ethernet cable sc 3 Insert the sealing rubber and claw through the Ethernet cable 20 RA ACT Hardware Manual 4 Make sure the bundled rubber ring is completely aligned on the gap on the gland body 5 Attach the gland body to the Ethernet port of the camera IMPORTANT Make sure the rubber ring is completely aligned and flat on the gland body to avoid possible water leakage 6 Connect the RJ 45 connector of the network cable to the Ethernet port of the camera 21 RA ACT Hardware Manual 7 Insert the sealing rubber and claw into the cable gland body 8 Attach the clamping nut to the cable gland body Make sure the clamping nut is tightly secured and the rubber is squeezed in to avoid water leakage DISCLAIMER ACTi will not be responsible for camera damage caused by water entering the cable connections
20. nt Types Pendant Mount Accessories Suitable when mounting the camera directly on walls or ceilings without additional mounting accessories See Installation Procedures on page 15 for more information Suitable when mounting the camera on a 4 Round or 4 Octagon Gangbox The use of gangbox is lawfully required in some areas in the United States A Gangbox Converter purchased separately is required for this type of installation Suitable when mounting the camera on the wall with the camera facing down as if installed on the ceiling The Wall Mount optional mounting accessory is required for this type of installation Suitable when installing the camera on high ceilings where a straight tube is used to lower the camera The Pendant Mount with Mount Kit optional accessory set is required for this type of installation e For more information about the mounting solutions and accessories please check the Mounting Accessory Selector in our website e The above mounting accessories are not included in the package Contact your sales agents to purchase 14 ACTI Connecting Vision DM Hardware Manual Installation Procedures This section describes procedures in mounting the camera on a flat surface NOTE The camera images on this documentation are for reference only and may be different from the actual camera Step 1 Prepare for Installation 1 Before installing the camera prepare the ad
21. o connectors with Waterproof Tape can be purchased in hardware stores DISCLAIMER AC Ti will not be responsible for camera damage due by water leakage caused by improper waterproofing of cables 2 ACTI Connecting Vision DM Hardware Manual How to Replace the Dome Cover For more discrete surveillance needs the pre installed dome cover can be replaced with a smoked vandal proof dome cover The smoked dome cover is an optiona accessory contact your sales agent to purchase To replace the dome cover follow the procedures below 1 Open the dome cover 2 Remove the six 6 screws securing the dome cover bracket Note that one 1 screw is used as a hook to attach the dome cover to the camera body 3 Remove the bracket and then the transparent dome cover 28 ACTI Connecting Vision da Hardware Manual 4 Remove the black rubber from the transparent dome cover and place the black rubber to the replacement dome cover wo 5 Install the replacement dome cover and then the bracket 6 Align the screw holes and secure the five 5 screws first Take note of the screw hole which must not be screwed at this point 29 ACTI Connecting Vision DM Hardware Manual 7 Insert the screw to the eyelet of the camera hook 8 Attach the last screw to the dome cover bracket
22. re will be an instant report as follows Total 69 Refresh scx ror IP Address 172 16 26 107 IP Address NetMask Device Settings Serial No E82 A XX 13C 00016 Change Network Address MAC Address 00 0F 7C 0A 5D 1F 172 16 26 63 255 255 255 0 Firmware Upgrade FW Version A1D 500 V6 06 16 AC Config Backup Model Megapixel IP Dome Config Restore Multicast IP 228 5 6 1 Reset Save amp Reboot Status 172 16 26 126 E91 A XX 13B 00154 00 0F 7C 0A 3E B9 A1D 500 V6 06 16 AC Megapixel IP Dome 228 5 6 1 172 16 26 35 E918 A XX 14D 00018 00 0F 7C 0D 5F 7F A1D 500 V6 07 10 AC Megapixel IP Dome 172 16 26 21 E918MA XX 14D 00018 00 0F 7C 0D 5F 93 A1D 500 V6 07 10 AC Megapixel IP Dome 172 16 26 34 E919 A XX 14D 00008 00 0F 7C 0D 5F 9D A1D 500 V6 07 10 AC Hemispheric Camera 172 16 26 37 E919MA XX 14D 00008 00 0F 7C 0D 68 71 A1D 500 V6 07 10 AC Hemispheric Camera 172 16 26 177 921 A XX 14D 00012 00 0F 7C 00 68 7F A1D 500 V6 07 10 AC Hemispheric Camera 172 16 26 32 E921 A XX 14D 00018 00 0F 7C 0D 68 85 A1D 500 V6 07 10 AC Hemispheric Camera 172 16 26 40 E921MA XX 14D 00018 00 0F 7C 0D 68 99 A1D 500 V6 07 10 AC Hemispheric Camera 172 16 26 33 E922 A XX 14D 00018 _00 0F 7C 00 68 AD A1D 500 V6 07 10 AC Megapixel IP Dome 172 16 26 39 E922MA XX 14D
23. regions All the other configurations When using non Internet Explorer browsers free third party software plug ins must be installed to the PC first to be able to get the live video feed from the camera Required Plug in Other non Internet Explorer Basic VLC Media Player browsers Disclaimer Notice The camera manufacturer does not guarantee the compatibility of its cameras with VLC player or QuickTime since these are third party softwares The third party has the right to modify their utility any time which might affect the compatibility In such cases please use Internet Explorer browser instead When using Internet Explorer browser the ActiveX control for video stream management will be downloaded from the camera directly the user just has to accept the use of such control when prompted so No other third party utilities are required to be installed in such case 5 iii DM ACTi Connecting Vision Hardware Manual The following examples in this manual are based on Internet Explorer browser in order to cover all functions of the camera Assuming that the camera s IP address is 192 168 0 100 you can access it by opening the Web browser and typing the following address into Web browser s address bar Upon successful connection to the camera the user interface called Web Configurator would appear together with the login page The HTTP port number was not added behind the IP address since the
24. se the Dome COVer nanne eneen nennenennrnen 24 Other Adjustments and Accessories 25 How to Install Remove the Memory Card cssceeeeeeeeees 25 How to Insert the Memory Card annen eneen eneen eneen 25 How to Remove the Memory Card aanne eneen eneen 25 ACTI Connecting Vision D4 ACTi Connecting Vision Hardware Manual How to Adjust the Fisheye View Orientation for E919 E921 E923 only saves acecesivecevecisesevecinedeveseucdavecinsseceninecen 26 How to Connect Audio In Device nas snnnare enaar en nnnnen eenn 27 How to Replace the Dome Cover nn nnansnnnnnnenenanenenanen eenn 28 Accessing the Camera 31 Configure the IP Addresses nnnannnnenane menens nennne nennen 31 Using DHCP Server to Assign IP Addresses unne 31 Using the Default Camera IP Address aaneen ennn 33 Access th Gamera enen anke 35 D4 ACTi Connecting Vision Hardware Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product Heed all warnings You must adhere to all the warnings on the product and in the instruction manual Failure to follow the safety instruction given may directly endanger people cause damage to the system or to other equipment Servicing Do not attempt to service this video device yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer a
25. ualified service personnel Damage Requiring service Disconnect this video product from the power supply immediately and refer servicing to qualified service personnel under the following conditions 1 When the power supply cord or plug is damaged If liquid has been spilled or objects have fallen into the video product 3 If the video product has been directly exposed to rain or water If the video product does not operate normally by following the operating Instructions in this manual Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation Safety Check Upon completion of any service or repairs to this video product ask the service technician to perform safety checks to determine if the video product is in proper operating condition Pp ACTI Connecting Vision Hardware Manual Introduction List of Models This hardware manual contains the following models 3MP Outdoor Mini Dome with Superior WDR Fixed lens E918 3MP Outdoor Mini Dome with Superior WDR M12 connector E918M Fixed lens 3MP Outdoor Mini Fisheye Dome with Superior WDR Fixed lens E919 3MP Outdoor Mini Fisheye Dome with Superior WDR M12 E919M connector Fixed lens E920 5MP Outdoor Mini Dome with Basic WDR Fixed lens 5MP Outdoor Mi
Download Pdf Manuals
Related Search