Instruction Sheet
Contents
1. Limitations GUARDIAN FALL PROTECTION PERFORMANCE SAFETY GEAR Fall Clearance There must be sufficient clearance below the anchorage connector to arrest a fall before the user strikes the ground or an obstruction When calculating fall clearance account for a MINIMUM 3 safety factor deceleration distance user height length of lanyard SRL and all other applicable factors Diagram shown is an example fall clearance calculation ONLY FALL CLEARANCE CALCULATION Required distance from anchorage 19 total Lanyard length 6 total Deceleration distance 4 total Height of harness dorsal D ring from worker s feet 6 total Safety factor 3 total Swing Falls Prior to installation or use make considerations for eliminating or minimizing all swing fall hazards Swing falls occur when the anchor is not directly above the location where a fall occurs Always work as close to in line with the anchor point as possible Swing falls significantly increase the likelihood of serious injury or death in the event of a fall GUARDIAN FALL PROTECTION PERFORMANCE SAFETY GEAR Compatibility When making connections with G Link SRLs eliminate all possibility of roll out Roll out occurs when interference between a hook and the attachment point causes the hook gate to unintentionally open and release All connections must be selected and deemed compatible with G Link SRLs by a Competent Person All2. Link SRL lifeline retraction by pulling out a minimum 4 and allowing it to retract under light tension lifeline must retract completely Pull lifeline sharply to test braking function brakes must engage Check shock pack for signs of deployment and or fall arrest indicator for signs of activation IMMEDIATELY remove from service if G Link SRL does not function properly or if any evidence of exposure to forces of fall arrest exists Ensure that applicable work area is free of all damage including but not limited to debris rot rust decay cracking and hazardous materials Ensure that selected work area will support the application specific minimum loads set forth in this instruction manual Work area MUST be stable Every 6 months a Competent Person other than the user must inspect G Link SRLs Competent Person inspections MUST be recorded in inspection log in instruction manual and on equipment inspection grid label The Competent Person must sign their initials in the box corresponding to the month and year the inspection took place During inspection consider all applications and hazards G Link SRLs have been subjected to gt GUARDIAN FALL PROTECTION PERFORMANCE SAFETY GEAR Product Specific Applications www guardianfall com Use of equipment in unintended applications may result in serious injury or death Maximum 1 attachment per connection point Personal Fall Arrest G Links may be used to support a MAXIMUM 1 Pers
3. analysis of the workplace must anticipate where workers will be performing their duties the routes they will take to reach their work and the potential and existing fall hazards they may be exposed to Fall protection equipment must be chosen by a Competent Person Selections must account for all potential hazardous workplace conditions All fall protection equipment should be purchased new and in an unused condition Fall protection systems must be selected and installed under the supervision of a Competent Person and used in a compliant manner Fall protection systems must be designed in a manner compliant with all federal state and safety regulations Unless explicitly stated otherwise the maximum allowable free fall distance for lanyards must not exceed 6 No free fall allowed for non LE SRLs SRLs must arrest falls within 54 Forces applied to anchors must be calculated by a Competent Person Harnesses and connectors selected must be compliant with manufacturer s instructions and must be of compatible size and configuration A pre planned rescue procedure in the case of a fall is required The rescue plan must be project specific The rescue plan must allow for employees to rescue themselves or provide an alternative means for their prompt rescue Store rescue equipment in an easily accessible and clearly marked area Training of Authorized Persons to correctly erect disassemble inspect maintain store and use equ
4. connector gates must be self closing and self locking and withstand minimum loads of 3 600 Ibs See the following for examples of compatible incompatible connections Connector closed and locked to D ring OK Two or more snap hooks or carabiners connected to each other NO Two connectors to same D ring NO Incompatible or irregular application which may increase risk of roll out NO Connector to integral lanyard NO Connector directly to webbing NO Application that places load on gate NO Connector directly to horizontal lifeline NO www guardianfall com N ron 00 ire N e 00 8 gt lt a wo e No 7 No No e 00 i dem 6305 S 23151 St Kent WA 98032 Guardian Fall Protection GUARDIAN FALL PROTECTION Correct Anchorage Positioning This chart details allowable working zones required to reduce risk of swing falls and improper side loading ALWAYS adhere to information specified by chart Anchor Distance Working Distance Working Angle From Along Roof Edge From Leading Edge Y Either Direction X Perpendicular For example if the anchorage connector is 6 from the leading edge Y the working distance X is 8 in each direction from the perpendicular which translates to a 53 working angle Key X Working Distance Along Roof Edge Y Distance From Leading Edge 0 Tot
5. GUARDIAN FALL PROTECTION PERFORMANCE SAFETY GEAR Product Name G Link SRL Part 10947 10993 10994 10995 10996 10997 10998 Instruction Manual Do not throw away these instructions Read and understand these instructions before using equipment www guardianfall com N fon o0 Ne oo gt lt un o0 M Mel 1 T cu 6305 S 231st St Kent WA 98032 Guardian Fall Protection GUARDIAN FALL PROTECTION PERFORMANCE SAFETY GEAR Table of Contents Introduction _ 12 Applicable Safety Standards _ _ _ DEDE 22 eee 2 Worker Classifications Ber A Safety Information 2 2 Le 3 4 Maintenance Cleaning and Storage 2 5 Inspection _ _ E NISUS nds 5 Product Specific 5_________________________ 6 eno es A i Mo aA gei 7 9 Components 5________________________ 10 Installation and Use _ z _ 1 Labels _ 2 2 mE M m 12 13 Inspection Log 14 Notes _ _ A eut CRI Se ae Sener 74 Introduction Thank you for purchasing a Guardian Fall Protection G Link SRL This manual must be read and understood in its entirety and used as part of an employee training program as required by OSHA or any applicable state agency This and any other included instructions must be made available to the user of the equip
6. al Working Angle gt GUARDIAN FALL PROTECTION PERFORMANCE SAFETY GEAR Components and Specifications Materials Nylon stainless steel and aluminum www quardianfall corn G Link Connector Bracket g A 3 a O SRL Web Housing gt Absorber N lon Dy j No e ee x is ea 1 No j o0 w E E at Connector d Shown w Snap Hook 6305 S 231st St Kent WA 98032 10947 G Link Connector Bracket w High Strength Carabiner 10994 G Link Dual 11 Retractable System With Aluminum Snap Hooks 1096 6 G Link Dual 6 Retractable System With Steel Rebar Hooks 10998 68 G Link Dual 6 Retractable System With Aluminum Rebar Hooks Guardian Fall Protection www guardianfall corn N fon o0 jm Ne oo gt lt a o0 M Mel 1 Hec cu 6305 S 231st St Kent WA 98032 Guardian Fall Protection GUARDIAN FALL PROTECTION PERFORMANCE SAFETY GEAR Installation and Use G Links MUST NEVER be used in Leading Edge LE applications No free fall is allowed ALWAYS avoid lifeline contact with sharp or abrasive edges and surfaces In Fall Arrest applications SRL must always be positioned at or above harness dorsal D ring AND at or below anchor point 1 All components of the personal fall arrest system must be sele
7. cted and deemed compatible with G Link by a Competent Person 2 Ensure structure to which SRL is to be attached and on which work is to be performed is free of all hazards including but not limited to debris rot rust sharp or abrasive edges and surfaces and hazardous materials 3 G Links are primarily intended for use in mobile applications Use a compatible carabiner to connect G Link Carabiner Connection Point to user harness dorsal D ring NEVER attach G Link snap hooks or rebar hooks to harness when used in this manner 4 Attach G Link snap hook or rebar hook to a compatible anchorage connector NEVER make connections to anchorages that will allow harness dorsal D ring to be positioned above anchor point If using SRL with rebar hook configuration rebar hooks must ONLY be connected to compatible structural rebar 5 Ensure 100 tie off will be maintained at all times ALWAYS attach disengaged snap hook or rebar hook to a compatible anchorage connector prior to unhooking engaged snap hook or rebar hook G Links configured with snap hooks may also be used in stationary applications with the Carabiner Connection Point attached with a compatible carabiner to an anchorage connector at or above the harness dorsal D ring The snap hook of one lifeline leg may then be attached to a harness D ring compatible with the application NEVER attach both lifeline legs to the harness NEVER attach rebar hooks to the harness at any time G L
8. ink for MAXIMUM 1 worker ONLY GUARDIAN FALL PROTECTION Labels 1 1 8 Front gt GUARDIAN FALL PROTECTION PERFORMANCE SAFETY GEAR YOUR SAFETY COMPANY FOR LIFE FALL ARREST 90061 Rev B ATTACHMENT GUARDIAN ONLY USE ANSI FALL PROTECTION 1359 12 09 CARABINER 800 466 6385 6305 5 23151 51 Kent WA 98032 SRL Attachment SRL Attachment OSHA 1926 Subpart M ANSI 2359 1 07 OSHA 1910 G Lin ANSI A10 32 12 Part 10947 10993 10994 10995 10996 10997 10998 E mimos DO NOT REMOVE LABELS GUARDIAN FALL PROTECTION Back Manufacturer s instructions product at time of shipment must be read prior to use Instructions must be followed for proper use maintenance and inspection Alterations or misuse of this product or failure to follow instructions may result in serious inju death NOT USER REPAIRABLE DO NOT REMOVE THIS LABEL No free fall positioned at lifeline contact with sharp edges For u trained persons only Ensure connection to anchor ecured properly before use Not suitable for horizontal use May be used as a component of a PFAS in HLL applications Design installation and utilization of HLLs must be supervised by a Qualified Person PERSON MUST ENSURE COMPATIBILITY OF ALL COMPONENTS READ AND FULLY UNDERSTAND ALL INSTRUCTIONS BEFORE USE FAILURE TO pplied wi
9. ipment must be provided by a Competent Person Training must include the ability to recognize fall hazards minimize the likelihood of fall hazards and the correct use of personal fall arrest systems gt GUARDIAN FALL PROTECTION PERFORMANCE SAFETY GEAR NEVER use fall protection equipment of any kind to hang lift support or hoist tools or equipment unless explicitly certified for such use Maintenance of equipment must be done according to manufacturer s instructions Equipment instructions must be retained for reference Prior to EACH use all equipment in a fall protection system must be inspected for any potential or existing deficiencies that may result in its failure or reduced functionality IMMEDIATELY remove equipment from service if any deficiencies are found Equipment must be inspected by a Competent Person at least every six months These inspections must be documented in equipment instruction manual and on equipment inspection grid label Equipment must be inspected for defects including but not limited to the absence of required labels or markings improper form fit function evidence of cracks sharp edges deformation corrosion excessive heating alteration excessive wear fraying knotting abrasion and absence of parts Equipment that fails inspection in any way must immediately be removed from use or repaired by an entity approved by the manufacturer No on site repair of equipment unless explicitly pe
10. ment The user must understand how to safely and effectively use the G Link SRL and all fall safety equipment used in combination with the G Link SRL gt GUARDIAN FALL PROTECTION PERFORMANCE SAFETY GEAR User Information Date of First Use Serial Trainer User Applicable Safety Standards When used according to instruction specifications this product meets or exceeds all applicable OSHA 1926 Subpart M OSHA 1910 ANSI 7359 14 2012 and ANSI A10 32 2012 standards for fall protection Applicable standards and regulations depend on the type of work being done and also might include state regulations if applicable Consult regulatory agencies for more information on personal fall arrest systems and associated components Worker Classifications Understand the following definitions of those who work near or who may be exposed to fall hazards Qualified Person A person with an accredited degree or certification and with extensive experience or sufficient professional standing who is considered proficient in planning and reviewing the conformity of fall protection and rescue systems Competent Person A highly trained and experienced person who is ASSIGNED BY THE EMPLOYER to be responsible for all elements of a fall safety program including but not limited to its regulation management and application A person who is proficient in identifying existing and predictable fall hazards and who has the authority to stop
11. onal Fall Arrest System PFAS for use in Fall Arrest applications Structure must withstand loads applied in the directions permitted by the system of at least 5 000 Ibs No free fall is permitted SRL must always be positioned at or above harness dorsal D ring AND at or below anchor point Applicable D ring Dorsal Restraint G Link SRLs may be used in Restraint applications Restraint systems prevent workers from reaching the leading edge of a fall hazard Always account for fully deployed length of lanyard SRL Structure must withstand loads applied in the directions permitted by the system of at least 1 000 Ibs No free fall is permitted Restraint systems may only be used on surfaces with slopes up to 4 12 vertical horizontal Applicable D rings Dorsal Chest Side Shoulder o0 D r gt lt 1 Ut co w i gt E For all applications worker weight capacity range including all clothing tools and equipment is 130 310 Ibs or up to 420 165 if used in combination with equipment explicitly certified for such use 6305 S 231st St Kent WA 98032 Guardian Fall Protection www guardianfall corn N fon o0 Eis Nel gt lt gt m a o0 M Ke D Ke NO o oo w fart 6305 S 231st St Kent WA 98032 Guardian Fall Protection
12. rdian Fall Protection GUARDIAN FALL PROTECTION PERFORMANCE SAFETY GEAR Maintenance Cleaning and Storage Repairs to G Link SRLs can only be made by a Guardian Fall Protection representative or an entity authorized by Guardian Contact Guardian for all maintenance and repair needs at 1 800 466 6385 If a G Link SRL fails inspection in any way immediately remove it from service and contact Guardian to inquire about its return or repair Cleaning after use is important for maintaining the safety and longevity of G Link SRLs Remove all dirt corrosives and contaminants from G Link SRLs before and after each use If a G Link SRL cannot be cleaned with plain water use mild soap and water then rinse and wipe dry NEVER clean G Link SRLs with corrosive substances When not in use store equipment where it will not be affected by heat light excessive moisture chemicals or other degrading elements Inspection KEEP INSTRUCTIONS AVAILABLE FOR REFERENCE Record Date of First Use Prior to EACH use inspect G Link SRLs for deficiencies including but not limited to corrosion deformation pits burrs rough surfaces sharp edges cracking rust paint buildup excessive heating alteration broken stitching fraying bird caging and missing or illegible labels Inspect full length of lifeline IMMEDIATELY remove G Link SRL from service if defects or damage are found or if exposed to forces of fall arrest Prior to EACH use check G
13. rmitted by Guardian Fall Protection Equipment subjected to forces of fall arrest must immediately be removed from use Snap hooks carabiners and other connectors must be selected and applied in a compatible fashion All risk of disengagement must be eliminated All snap hooks and carabiners must be self locking and self closing and must never be connected to each other Age fitness and health conditions can seriously affect the worker should a fall occur Consult a doctor if there is any reason to doubt a user s ability to withstand and safely absorb fall arrest forces or perform set up of equipment Pregnant women and minors must not use this equipment Physical harm may still occur even if fall safety equipment functions correctly Sustained post fall suspension may result in serious injury or death Use trauma relief straps to reduce the effects of suspension trauma Allowable individual worker weight limit including all equipment unless explicitly stated otherwise is 130 310 Ibs www guardianfall com lon oe ie NO ee gt lt iz ms ea 1 No ee E 6305 S 231st St Kent WA 98032 Guardian Fall Protection www qguardianfall com N fon o0 jm R Ne gt gt lt fis a o0 M Ke D oo fart 6305 S 231st St Kent WA 98032 Gua
14. th this i TION Before each use pect device per user manual including locking function pull sharply to test retraction function lifeline function function and condition of connectors housing and fasteners legibility of labels and any evidence of defects mage or missing parts Inspection by a Competent Person required monthly Inspect shock absorber for signs of previous deployment or load Torn or stretched pl on shock pack is an indication that an impact has occurred and the unit must be removed from serv ed to arrest the fe from service Do not inspection reveals Powerful spring inside do not remove Capacity 1 person 130 310 Ibs including all equipment or up to 420 lbs see instructions Bracket Material Zinc Plated Steel DO SO MAY RESULT IN SERIOUS INJURY OR DEATH ATTACH RETRACTABLES DIRECTLY TO THIS BRACKET DO NOT USE ANY COMPONENT BETWEEN THE RETRACTABLE AND THIS BRACKET GUARDIAN FALL PROTECTION PERFORMANCE SAFETY GEAR Inspection Log User must inspect prior to EACH use Competent Person other than user must complete formal inspection at least every 6 months Competent Person to inspect and initial www quardianfall corn Date of First Use Product lifetime is indefinite 5 years from Date of First Use or if not recorded from Date of Manufacture as long as it passes pre use and Competent Person inspections This inspection log must be specific to one G Link SRL Separate inspec
15. tion logs must be used for each G Link SRL All inspection records must be made visible and available to all users at all times on D r Ne JFMAMJJASOND 5 YR e No YR A No 99 z 24 So YR If equipment fails inspection IMMEDIATELY REMOVE FROM SERVICE Notes N m oo e c C 9 un mM N vi wn M Ne Guardian Fall Protection
16. work in order to eliminate hazards Authorized Person A person who is assigned by their employer to work around or be subject to potential or existing fall hazards It is the responsibility of a Qualified or Competent person to supervise the job site and ensure all applicable safety regulations are complied with www guardianfall com lon is j NO e ce x S ea 1 NO ee w E 6305 S 231st St Kent WA 98032 Guardian Fall Protection www guardianfall corn N fon o0 jm Ne gt gt lt fis un o0 M Ke 1 NO oo Hec cu 6305 S 231st St Kent WA 98032 Guardian Fall Protection GUARDIAN FALL PROTECTION PERFORMANCE SAFETY GEAR Safety Information Failure to understand and comply with safety regulations may result in serious injury or death Regulations included herein are not all inclusive are for reference only and are not intended to replace a Competent Person s judgement or knowledge of federal or state standards Do not alter equipment Do not misuse equipment Workplace conditions including but not limited to flame corrosive chemicals electrical shock sharp objects machinery abrasive substances weather conditions and uneven surfaces must be assessed by a Competent Person before fall protection equipment is selected The
Download Pdf Manuals
Related Search