Solar Charge Controller CMP45(English)
Contents
1. 4 wire is suggested Diagram of Connection 4 00 screen H Button is pressed Battery xx xV Charge xx xA Startup Menu Battery xx V Charge xx xA Check the system temperature MENU Check the charging current MENT Charge Check the discharging current Charge xxxxxx Ah MENU Load xxxxxx Ah Check the battery capacitance Load xxxxxx Ah MENU Battery SOC xxx Check the charge off voltage of battery Battery SOC xxx MENU Charge off xx xV Setup the Charge off voltage of battery Charge off xx xV Check the load off voltage of loads Charge off xx xV MENU Load off xx xV Setup the Load off Voltage of loads Load off xx xV Load off xx xV PRETE HF tll ae Check the load on voltage of loads Setup the load on voltage of loads adorn Resume the default parameters of Charge off voltage of Battery Load on amp off Voltage of loads Press MENU for more than 5 seconds Startup after over loads Reduce quantity of loads Startup after short circuit Remove malfunction 5 TROUBLE SHOOTING Trouble Green light goes out the loads stop working and LCD Screen shows Battery low Reason Low voltage of battery Solution Charge the battery or change the battery Trouble Green light goes out the loads stops working and LCD shows Reason Overload Solution Reduce the quantity of loads2. the Load on voltage according to the voltage of battery These default parameters are setup as the standard environment temperature is 25 C According to varies system temperature the controller will automatically compensate the temperature of the charging voltage Users could setup the Charge on or off voltage the load off voltage the Load on voltage etc according to their requirements To prevent battery from over discharging Controller will automatically control the lowest Load off voltage of the load which is no less than 10V as per 12V battery or 20V as per 24V battery or 42V as per 48V battery If voltage of the battery is less than 10V or 20V 42V the button will stop working To recover the default parameters please keep pressing the button Menu for over 5 seconds RI 76 ae 3 CONNECTION As indicated in diagram Connect and poles of solar panel with the correct ports on the controller the first and second ports from the left Connect and poles of battery with the correct ports on the controller the third and fourth ports from the left Connect and poles of load with the correct ports on the controller the fifth and sixth ports from the left Attention Correctly connect the electrodes of solar panels battery and loads Choose the proper wire according to the current of the loads the diameter could not be too small Bigger than
3. 10000 faanao com SOLAR CHARGE CONTROLLER USER S MANUAL TABLE CONTENT SAFETY FEATURES SYSTEM CONNECTION OPERATION TROUBLE SHOOTING ACCESSORY INSTALLATION SPECIFICATIONS 0 76 EFE ll ae 1 SAFETY The factors referring to users and property safety have been considered when designing the products However the incorrect connection may cause the breakdown of system and even safety accident For your safety and interests the following rules must be observed during the operation Installation of this product shall be carried out by professional staffs If user is not sure with the installation procedure please contact the local agent of our company Prevent any liquid from spattering on controller Do not clean the controller with wet cloth Keep children and incapacity persons away from controller Keep controller away from electrical heater warmer and other source of heat avoid controller from sun beat Please check the rated voltage of solar panel battery and loads before connection Their rated voltages all should be 12V or 24V 48V Make sure to connect the positive and negative poles among Solar panels Battery and Loads correctly The diameter of connecting cable must be sufficient for the loads The total rated current of solar panel and loads must be less than controller s rated current Components of system must be correctly and firmly connected Connecting wired bat
4. and then press Button Trouble Green light goes out the loads stop working and LCD Screen shows Short circuit Reason Short circuit is happening in system Solution Disconnecting the malfunction and then press the button Phenomenon Green LED is on Loads are normally working Phenomenon Red LED is on Battery is charged up strongly Phenomenon Red LED is flickering Battery is charged up in constant voltage or floating Trouble Red LED goes out Reason Charge off of battery Solution This is the common phenomenon during nights If it is so during days please carefully check the connection among Solar panels Controller and Battery Standard Accessory Optional Accessory Installation Installation RI 76 ae 6 ACCESSORY INSTALLATION Near distance thermoscope Plug the thermoscope into the socket top of controller before running of controller and then connect battery with the controller The thermoscope will normally work after one minute Operate as indicated in the fourth Chapter the environmental temperature of controller will be available on LCD Long distance thermoscope Such thermoscope is suitable to the following condition the location of battery is far away from the Controller Please give the length of wire between battery and controller for ordering the proper thermoscope Plug the thermoscope into the socket top of controller before running of controller an
5. d then connect battery with the controller The thermoscope will normally work after one minute Operate as indicated in the fourth Chapter the environmental temperature of controller will be available on LCD 7 SPECIFICATIONS Temp Zero Load Voltage Full Charge Resume Low Voltage Cut Voltage oni CMP45 30A lt 30A Pas 13 7 12 6 12 10 5V 12V CMP45 40A 4 Singh lt 40 2 24 2 24 2 24V ne 4 48V 4 48V 4 48V CMP45 45A CMP45 80A 48V lt 80A 54 8V 50 4V 42V CMP45 110A 48V lt 110A Compensation 3mv C cell Default or user set Loses lt 45mA Drop lt 520mv 6 air lt 550mv lt 600mv 25 lt 600mv mm lt 600mv Notice The figures of Full Charge Cut Resume Voltage and Low Voltage Cut are either default set by this manufacturer or adjusted by well trained user 70000 htto 31 ccc taodao com 486 755 29660524
6. tery positive and negative poles directly is prohibited 2 FEATURES CPU controlled CMP45 30 45 solar charge controller is able to adjust the charge current and decide if to supply the loads electricity according to the voltage of battery The product also has following features Generally keep the battery on full voltage condition Prevent the battery from over charging Prevent the battery from over discharging Prevent supplying electricity from the battery to solar panels during nights Reverse Polarity Protection for Battery Reverse Polarity Protection for Solar panels When the current of load exceeds the rated one of controller the controller will activate the protection mode and lock up the screen shows Overload When short circuit happens the Controller will activate the protection mode and lock up the screen show Short circuit When the battery s voltage is low the controller will automatically cut off loads from system and resume its working once the voltage of battery is back to normal Protection from the lightning strike When Controller is normally working the LCD Screen will show the voltage of battery charging current and current of loads in turn in every 5 seconds Controller is always counting and saving the Charging Current Hours and Discharging Current Hours of the Battery When controller starts up controller will self setup the Charging off voltage the Load off voltage and
Download Pdf Manuals
Related Search