USER MANUAL
Contents
1. MODELED Valued Value1 Value2 Value3 Value4 Value5 Value6 Yellow Red No Initial Going from lowest to highest inital brake setting alternate Brake value 1 minimum value 6 maximum Team Tips A good starting point for the brake setting on your radio is 80 bonded and 70 sintered for all classes Make sure you do the radio setup with all settings on the radio on 100 MODE 4 Automatic Brake allows you to set a slight braking action which is applied in the neutral range This enables you to simulate the feel of a brushed motor and also hold the throttle on longer when ente ring a turn For brushless motors you achieve the same natural slowdown as a brushed motor with no autobrake when you set value 1 2 for motors with bonded magnets or 0 1 for motors with sintered magnets MODELED ValueO Value1 Walue2 Value3 Value4 Value5 Value 6 Yellow Red No Automatic Going from lowest to highest automatic brake setting same time Brake value 1 minimum value 6 maximum 9 TROUBLESHOOTING GUIDE EXPLANATION If no remark cause can be either with brushless or brushed motor If BM is indicated cause only relating to brushed motor SYMPTOM CAUSE CT RREMEDY Replace components one by one Motor runs in reverse when accelera BM Motor connected incorrectly Connect motor correctly ting forward on the transmitter Insufficient performance Motor pinion too big or gear ratio too long Use2. wenn der Motor noch nicht eingebaut ist Durch die extrem hohen Drehzahlen ohne Last kann der Motor besch digt werden L ten Sie bei Verwendung dieses Reglers niemals eine Schottky Diode an den Motor Solange der Motor an den Regler angeschlossen ist d rfen Sie niemals den Motor mit einem separaten Akku oder mit einem Motor Einlaufger t laufen lassen Stellen Sie sicher dass die K hlbleche der Fets sich niemals ber hren Kurzschlu gefahr Ver ndern Sie niemals die Polarit t des Empf ngersteckers Schlie en Sie s mtliche Teile der Ausr stung sorgf ltig an Falls sich die Verbindungen durch Vibrationen l sen k nnen Sie die Kontrolle ber das Modell verlieren Vermeiden Sie es beim Wechseln der Powerkabel l nger als 5 Sekunden je L tstelle zu l ten um eine Be sch digung der Bauteile durch berhitzung auszuschlie en Verwenden Sie zum L ten eine leistungsstarke L tstation mit mind 60W Der Hersteller kann nicht f r Sch den verantwortlich gemacht werden die infolge von Nichtbeachtung der Sicherheitshinweise und Warnungen verursacht werden Das Symbol einer durchgestrichenen Abfalltonne auf R dern bedeutet dass das Produkt in der Europ ischen Union einer getrennten M llsammlung zugef hrt werden muss Diese Pro dukte d rfen nicht ber den unsortierten Hausm ll entsorgt werden ALLGEMEINE GEW HRLEISTUNGS UND REPARATURBESTIMMUNGEN Produkte der LRP electronic GmbH nachfolgend LRP genannt wer
3. you are 40 C away from thermal shutdown and therefore safe Launch Control the launch control allows rocket like starts After activation it gives you more power one time for the start this feature is only recommended to be used with touring cars on high traction surfaces Activate launch control Hold trigger on radio at full brake for 5sec before start Ready and active AutoCell System Ready for the next battery technology LiPo batteries LRP s exclusive and smart AutoCell System ensures that LiPo batteries can be used safely without accidentially deep discharging of the cells The motor function will be shut off and the SET LED will flash if the system recognises very low battery voltage ADPC Brushless Power Profiles results in more power and better driveability Depending on the status of the car start acceleration full speed the software calculates the perfect motor management Higher value means more overall power and aggressive response Caution Do not advance mechanical timing on the motor when using high ADPC profiles D E M S Brushed Power Profiles The known and world s winning D E M S Brushed Quantum style power programs have been implemented into the LRP SPX Competition StockSpec as well Higher value means more overall power and aggressive response Automatic Brushless Brushed Adaption The LRP exclusive Automatic Brushless Brushed Adap tation detects the connected motor type during turn on
4. smaller motor pinion shorter gear ratio E g poor brake power topspeed or B A Secret Transmitter settings changed after set up Repeat set up procedure off frequently too high the specifications of the speed control Motor never stops runs at constant Transmitter settings changed after set up Repeat set up procedure slow speed P Humidity water in speed control Immediately unplug and dry speed control Radio interference BM Motor suppressors not sufficient Solder capacitors to motor Receiver or antenna too close to power wires See Installation Tips and Installation motor battery or speed control Receiver aerial too short or coiled up Receiver defective too sensitive Replace components one by one Transmitter defective transmitter output power Only use original manufacturers crystals too low servo problem Poor battery connection Check plugs and connecting wires Transmitter batteries empty Replace recharge transmitter batteries Transmitter antenna too short Pull out antenna to full length Speed control defective Send in product for repair A WARNING NOTES No toy Not suitable for children under 14 years Keep the product out of the reach of children Pay close attention to the following points as they can de stroy the product and void your warranty Non observance of these points can lead to property damage personal and severe injuries e Never leave the product unsupervised while it is switched o
5. 0 270 313 0 73 Minute aus dem dst Festnetz Mobilfunkpreise k nnen abweichen eMail service lrp electronic de Web www LAP ce e LRP repariert das Produkt e R cksendung an Sie per Nachnahme
6. BAT to battery Plus e Black power wire gt Speedo BAT to battery Minus e The speed control is now ready to be set up see section 6 2 CONNECTIONS MOT C Orange MOT B Yellow BAT Black MOT A Blue BAT Red On Off Switch Power Capacitor Receiverwire Hall Sensor Connector RECEIVER CONNECTING WIRE This LRP speed control is equipped with an LRP Multicon receiver wire As supplied it will easily fit in all ordinary receivers HALL SENSOR WIRE This bi directional multipole wire connects the speed control and the motor Do not alter or modify this cable There are replaceable optional hall sensor wires available 81910 20cm 81920 10cm POWER WIRES For maximum performance 2 6mm power wires without any connectors are used The unique splitted solder tabs allow easy and convenient replacement of the power wires Nevertheless some soldering skills are required Avoid soldering longer then 5sec per soldering joint to prevent possible damage to the speed control due to overheating of the components There is a full replacement power wire set available 82505 Dear Customer thank you for your trust in this LRP product By purchasing a LRP SPX Competition StockSpec speed control you have chosen one of the most advanced speed controls of today This speed control with all of its high tech features and specially selected electronic components is one of the best speed controls currently avail
7. Frischluft Vermeiden Sie falschen Anschluss oder Verpolung des Pro dukts Alle Kabel und Verbindungen m ssen gut isoliert sein Kurz schl sse k nnen unter Umst nden das Produkt zerst ren Dieses Produkt oder andere elektronische Komponenten d rfen niemals mit Wasser Ol Treibstoffen oder anderen elektrisch leitenden Fl ssigkeiten in Ber hrung kommen da diese Mineralien enthalten k nnen die elektronische Schalt kreise korrodieren lassen Bei Kontakt mit diesen Stoffen m ssen Sie sofort den Betrieb einstellen und das Produkt sorgf ltig trocknen Die Originalstecker und Originalkabel d rfen niemals ver n dert oder abgeschnitten werden ffnen Sie niemals das Produkt und l ten Sie keinesfalls auf der Platine oder anderen Komponenten Benutzen Sie Ihr Produkt nicht mit ge ffnetem besch digtem oder fehlendem Geh use oder in Schrumpfschlauch Dies mindert den St rschutz kann Kurzschl sse verursa chen und das Produkt besch digen Entnehmen Sie immer den Akku aus Ihrem Produkt bzw trennen Sie das Produkt von der Stromquelle wenn das Produkt nicht verwendet wird Schalten Sie immer zuerst Ihren Sender ein bevor Sie den Empf nger oder Fahrtenregler einschalten Der Empf nger k nnte St rsignale auffangen Vollgas geben und Ihr Modell besch digen Beim Ausschalten beachten Sie die umgekehrte Reihenfolge Erst Empf nger und Fahrtenregler ausschalten dann Sender ausschalten Geben Sie keinesfalls Vollgas
8. RA00262 ORDER NO 80710 STOCK SOFTWARE BRUSHLESS BRUSHED OVER 3 5T BRUSHLESS STAR OVER 5T BRUSHED STOCK SPEC USER MANUAL LRP electronic GmbH Wilhelm Enssle Str 132 134 73630 Remshalden Germany info LRP cc www LRP cc 1 INSTALLATION The LRP SPX Competition StockSpec is supplied with 2 6mm power wires without connectors Be very careful with the correct wire sequence colors since an incorrect connection may damage the speed control Avoid creating solder bridges on the solder tabs and isolate all connections carefully Caution Avoid soldering longer then 5sec per soldering joint when replacing the power wires on the speed control and motor to prevent possible damage due to overheating of the components e Connect the speed control to the receiver position Channel 2 BRUSHLESS MOTOR e Blue power wire gt Speedo MOT A to motor A e Yellow power wire gt Speedo MOT B to motor B e Orange power wire gt Speedo MOT C to motor C e Connect the hall sensor cable to the speed control and the motor Hall Sensor Wire BRUSHED MOTOR e Blue Yellow power wire Speedo MOT A MOT B to Minus on the motor e Orange power wire gt Speedo MOT C to Plus on the motor together to minus e Doublecheck all connections before connecting the speed control to a battery CAUTION If battery is connected with reversed polarity it will destroy your speed control e Red power wire gt Speedo
9. able on the market e Advanced Digital e New Brake e 4 5 and 6 cell optimised e Sensored Design e IceDrive Design e 2 6mm Power Wires e Special Stock Hard and Software e Optimised ADPC profiles e Internal Temp Check system e Launch Control e AutoCell System e Big Power Capacitor Please read the following instructions carefully before you start using your LRP SPX Competition Stock Spec speed control This user guide contains important notes for the safety the use and the maintenance of this product Thus protecting yourself and avoid damages of the product Proceed according to the user guide in order to understand your LRP SPX Competition StockSpec speed control better Please take your time as you will have much more joy with your product if you know it exactly This user manual shall be kept in a safe place If another customer is using this product this manual has to be handed out together with it 3 SPECIFICATIONS Brushless Brushed yes Voltage Input 4 8 7 4V Brushless Brushed Adaption 24 5g Forward Reverse 6 0V 3 0A Typ Voltage Drop Brushless 20A Rated Current Brushless yes Compatible winding styles Brushless Power Wires 2 6mm Rec Motor Limit for Star winds Brushless yes Typ Voltage Drop Brushed 20A yes Rec Motor Limit Brushed yes Rated Current Brushed yes 4 adjustable Modes NiMH LiPo ADPC DEMS Power Profiles Initial and Automaticbrake yes Transistors ratin
10. den nach strengsten Qualit tskriterien gefertigt Wir gew hren die gesetzliche Gew hrleistung auf Produktions und Materialfehler die zum Zeitpunkt der Auslieferung des Produkts vorhanden waren F r gebrauchstypische Verschlei erscheinungen wird nicht gehaftet Diese Gew hrleistung gilt nicht f r M ngel die auf eine unsachgem e Benutzung mangelnde War tung Fremdeingriff oder mechanische Besch digung zur ckzuf hren sind Dies liegt unter Anderem vor bei Stecker abgeschnitten bzw kein verpolsicheres Stecksystem Empf ngerkabel und oder Schalter besch digt Geh use mechanisch besch digt Wasser Wasserr ckst nde im Geh use Mechanische Besch digung der Bauteile Platine Auf der Platine gel tet Ausnahme au en liegende L tlaschen Akkuseitig verpolt Bevor Sie dieses Produkt zur Reparatur einsenden pr fen Sie bitte zun chst alle anderen Komponenten in ihrem Modell und schauen Sie ggf in der Fehlerfibel des Produktes sofern vorhanden nach um andere St rquel len und Bedienfehler auszuschlie en Sollte das Produkt bei der berpr fung durch unsere Serviceabteilung keine Fehlfunktion aufweisen m ssen wir Ihnen hierf r die angefallenen Bearbeitungskosten laut Preisliste berechnen Mit der Einsendung des Produktes muss der Kunde mitteilen ob das Produkt in jedem Fall repariert werden soll Sollte kein Gew hrleistungs oder Garantieanspruch bestehen erfolgt die Produkt berpr fung und ggf Reparatur in jedem Fall
11. e kostenpflichtig gem unserer Preisliste Ein Gew hrleistungs oder Garantieanspruch kann nur anerkannt werden sofern eine Kopie des Kaufbelegs beigef gt ist Auf Ihre ausdr ckliche Anforderung erstellen wir einen kostenpflichtigen Kostenvoranschlag Wenn Sie nach Zusendung des Kostenvoranschlags den Auftrag zur Reparatur erteilen entfallen die Kostenvoranschlagskosten An unseren Kostenvoranschlag sind wir zwei Wochen ab Ausstellungsdatum gebunden F r eine schnelle Abwicklung Ihres Servicefalls legen Sie bitte eine ausf hrliche Fehlerbeschreibung und ihre Adressdaten der Einsendung bei Falls ein zur ckgesandtes defektes Produkt von LRP nicht mehr produziert wird und wir dieses nicht reparieren k nnen so erhalten Sie statt dessen ein mindestens gleichwertiges Produkt aus einer der Nachfolgeserien Die von LRP angegebenen Werte ber Gewicht Gr e oder Sonstiges sind als Richtwert zu verstehen LRP bernimmt keine formelle Verpflichtung f r derartige spezifische Angaben da sich durch technische Ver nde rungen die im Interesse des Produkts vorgenommen werden andere Werte ergeben k nnen LRP Werks Service e Produkt mit Kaufbeleg und Fehlerbeschreibung bruchsicher verpacken e Einsenden an LRP electronic GmbH Serviceabteilung Wilhelm Enssle Str 132 134 73630 Remshalden Deutschland Technik Service Hotline D 0900 577 4624 0900 LAP GMBH 0 49 Minute aus dem dt Festnetz Mobilfunkpreise k nnen abweichen A 090
12. ed defective product and we are unable to service it we shall provide you with a product that has at least the same value from one of the successor series The specifications like weight size and others should be seen as guide values Due to ongoing technical impro vements which are done in the interest of the product LRP does not take any responsibility for the accuracy of these specs LRP Distributor Service Package your product carefully and include sales receipt and detailed description of malfunction Send parcel to your national LRP distributor Distributor repairs or exchanges the product Shipment back to you usually by COD cash on delivery but this is subject to your national LRP distributor s general policy RA00263 Kein Spielzeug Nicht fiir Kinder unter 14 Jahren geeignet Bewahren Sie das Produkt au erhalb der Reichweite von klei nen Kindern auf Beachten Sie unbedingt die folgenden Hinweise da diese Ihr Produkt zerst ren k nnen und die Gew hrleistung ausschlie en Nichtbeachtung dieser Hinweise k nnen zu Sach und Personensch den und schweren Verletzungen f hren e Nassen Sie das Produkt niemals unbeaufsichtigt solange es eingeschaltet in Betrieb oder mit einer Stromquelle verbun den ist Im Falle eines Defekts k nnte dies Feuer am Produkt oder seiner Umgebung verursachen Wickeln Sie Ihr Produkt niemals mit Plastikfolie Metallfo lie oder Ahnlichem ein sondern sorgen Sie im Gegenteil f r
13. er and speed control then switch off the transmitter Never apply full throttle if the motor is not installed Due to the extremely high RPMs without load the motor can get damaged Never solder a Schottky diode to the motor when you are using this speed control If the speed control is connected to the motor never run the motor directly with a separate battery or run in device Never change the polarity of the receiver connector Always wire up all the parts of the equipment carefully If any of the connections come loose as a result of vibration you could loose control over your model Avoid soldering longer then 5 seconds per soldering joint when replacing the power wires to prevent possi ble damage to the product due to overheating of the components Use a high power soldering station with at least GOW for soldering The manufacturer can not be held responsible for damages which are a result of non observance of the warning notes and security advices The crossed out wheeled bin means that within the European Union the product must be taken to seperate collection at the product end of life Do not dispose of these products as unsorted municipal waste REPAIR PROCEDURES LIMITED WARRANTY All products from LRP electronic GmbH hereinafter called LRP are manufactured according to the highest quality standards LRP guarantees this product to be free from defects in materials or workmanship for 90 days non european countr
14. etition speed control without reverse function Sensored Brushless Technology Advanced Digital allows the perfect knowledge of the brushless motor s magnet position This results in perfect motor control at high and low RPM s as well as perfect brake control Multi Protection System 3 way protection The perfect protection against short circuits motor overload and overheating If your speed control faces overload the motor function will be shut off for protection and the SET LED will flash although the steering function is maintained Let the speed control cool down for a few minutes If you experience frequent shutdowns check for the following e Correct gear ratio refer to motor manual for gearing recommendations e ADPC setting too high higher value will heat up motor and speed control excessively e Motor is too strong or motor is damaged 7 MODE PROGRAMMING All modes are available for brushless and brushed motors speedo adapts automatically The LRP SPX Com petition StockSpec features 4 modes which enable you to adjust it to YOUR special requirements The factory settings are shown in grey colour How to get into programming the modes gt Press MODE button for 3 or more seconds How to check the stored values gt Count the number of flashes of the blue SET LED 1x value 1 2x value 2 etc gt Press SET button to increase value by one step gt Press MODE button once gt If you are in MODE 4 pres
15. g at 25 C junction temperature Specifications subject to change without notice measured at 7 2V 4 INSTALLATION TIPS Mount the speedo using the supplied thick black doubled sided tape Position the speed control where it is protected in the event of a crash Install the speed control so that you have easy access to the connector and buttons Make sure there is enough clearance about 3cm between the speed control power wires anten na and receiver Avoid any direct contact between power components the receiver or the antenna This can cause interference If interference occurs position the components at a different place in the model The aerial should be run vertically up and away from the receiver Avoid contact with any parts made of carbon fibre or metal If the aerial is too long don t coil up the excess length It is better to cut it down to a length of about 35 cm See also the instructions supplied with your radio control system Make sure there are enough cooling slits in the body This will increase the performance and life of all the electronic components HEATSINK We recommend using the supplied heatsink in order to achieve best performance even under extreme circumstances Clean the heatsink and stickerplate before you attach the clear thin Scotch 468MP thermal tape to guarantee perfect heat dissipation Caution Use ONLY the supplied clear thin Scotch 468MP thermal tape to attach the heatsink Do not us standard do
16. initialisation and adjusts the correct brushless or brushed operation automatically No adjustments required by yourself apart from the correct connection of each motor type don t forget the hall sensor wire for brushless Caution Keep in mind when swopping between brushless and brushed motors that the chosen mode values will be identical Changing Mode settings without the transmitter At race events you usually do not have access to your transmitter but never mind since you can simply disconnect the receiver lead from the receiver and change the MODE settings as described in section 7 Mode Programming Works Default Settings All LRP speed controls come factory adjusted defaults are grey shaded above If you loose track of the modes you can restore the works default settings With the transmitter switched on hold the SET button pressed while you switch on the speed control This returns the unit to the LRP works default settings Power Capacitor Never disconnect the power capacitor It offers increased punch and additional protection IceDrive Design LRP s secret IceDrive Design results in lower speedo temperature under all racing conditions and for both brushless brushed Sorry no further details to be disclosed Simply a step ahead of the competition Forward Brake Uncompromising and outstanding performance for top level competition was the target There fore the LRP engineering team developed a pure forward brake comp
17. is only from the original date of purchase verified by sales receipt This limited warranty doesn t cover defects which are a result of misuse improper maintenance outside interference or mechanical damage This applies among other things on Cut off original power plug or not using reverse polarity protected plugs Receiver wire and or switch wire damaged Mechanical damage of the case Humidity Water inside the speed control Mechanical damage of electronical components PCB Soldered on the PCB except on external solder tabs Connected speed control with reversed polarity To eliminate all other possibilities or improper handling first check all other components in your model and the trouble shooting guide if available before you send in this product for repair If products are sent in for repair which do operate perfectly we have to charge a service fee according to our pricelist With sending in this product the customer has to advise LRP if the product should be repaired in either case If there is neither a warranty nor guarantee claim the inspection of the product and the repairs if necessary in either case will be charged with a fee at the customers expense according to our price list A proof of purchase including date of purchase needs to be included Otherwise no warranty can be granted For quick repair and return service add your address and detailed description of the malfunction If LRP no longer manufactures a return
18. n in use or connected with a power source If a defect oc curs it could set fire to the product or the surroundings Never wrap your product in plastic film metal foil or similar In fact make sure it gets enough fresh air Avoid incorrect connections or connections with reversed polarity of the product All wires and connections have to be well insulated Short circuits can possibly destroy the product Never allow this product or other electronic components to come in contact with water oil or fuels or other electrocon ductive liquids as these could contain minerals which are harmful for electronic circuits If this happens stop the use of your product immediately and let it dry carefully Never cut off or modify the original plugs and original wires Never open the product and never solder on the PCB or other components Never use this product when the case is open damaged or missing or when the product is wrapped in a shrink fit tube This will reduce protection may cause short circuits and damage the product Always remove the battery from your product or disconnect the product from the power source if the product is not in use Always switch on your transmitter first before you switch on the receiver or the speed control The receiver could receive interference signals start full acceleration and damage your model When you switch off make sure you do so in the reverse sequence First switch off the receiv
19. s the MODE button one more time Table of settings values and modes see below grey shaded values show works default settings How to change the value How to get to the next Mode How to leave the programming mode MODE 1 AutoCell System we recommend using value 2 for 4 6 cells NiMH racing purposes which disengages the LiPo protection Value1 Value 2 LiPo NiMH 4 6cell NiMH MODE 2 ADPC Brushless Power Profiles only with connected Brushless motor allows you to adjust the SPX Competition StockSpec to your likes Either you run on stock or modified motors or on slippery or high traction surfaces we have incorporated a profile for you Higher value means more overall power and more aggressive throttle response Value5 Value6 Value7 Value 8 smooth smooth smooth Linear Linear Agressive agressive Agressive Power 1X Power 2X Power 3X Power 4X Power 6X Power 6X Power 7X Power 7X Modified Motor 4 0 to 8 5t Power Profiles Stock Motor 8 5 21 5t Power Profiles MODE 2 DEMS Brushed Power Profiles only with connected Brushed motor Higher value means more overall power and more aggressive throttle response MODELED Value1 Value2 Value3 Value4 Value5 Value6_ smooth very linear punch aggressive very aggres super aggres low traction linear increasing profile sive profile sive profile MODE 3 Initial Brake Allows you to set a certain level of hand brake effect
20. ter first then switch on the car For storage of the car disconnect the drive battery at any time CHECKING THE FUNCTIONS Check the LED s when moving your throttle stick and you will see if everything is setup correctly Neutral automatic brake inactive S Neutral automatic brake active DUO N blue Brake i brake rd bie 8 SPECIAL FEATURES Internal Temp Check System the LRP SPX Competition StockSpec allows you to read out the maximum internal temperature that the speedo reached To store it to the memory briefly apply brakes after the run before you turn the switch off You can convienently read out the temperature back in the pits since it remains stored until you turn it on the next time regularly which will reset the memory This new feature allows you to accurately check if all is running well or if you re close to shutdown already How to read out the temperature gt Switch at OFF position gt Keep MODE button pressed while you turn switch to ON then release button gt SET LED will start to flash blur MODE LED is off now count the number of flashes Basics e Thermal shutdown of the speedo would occur at 5 flashes e The higher the number of flashes the cooler the speedo ran e g the better it is e Every flash equals to 8 C temperature decrease Example gt you count 10 flashes after the run gt 10 5 5 e g 5 flashes away from shutdown gt 5x 8 C 40 C e g
21. uble sided tape to attach the heatsink as standard tape does not transfer heat Because of the physical principles of brushless technology the speed controls do get a little hotter then brushed systems Therefore it is required to let the speed control cool down completely after every run When running in extreme conditions high ambient temperature low turn motors high gear ratios etc we recom mend using the optional pre wired cooling fan 82500 which fits perfectly into the supplied heatsink Mount the power capacitor ina position whe re it is protected in the event of a crash The best place is right next to the speed control see picture Secure it with doublesided tape LRP SPX Competition StockSpec with mounted heatsink 5 SUPPRESSION mpide ONLY FOR BRUSHED MOTORS Motors with no capacitors or not enough capacitors may interfere with the speed control To avoid this solder the supplied capacitors to your motor see picture Mabuchi motor Racing motor capacitor 6 RADIO SPEED CONTROL SET UP In setup mode the LRP SPX COMPETITION STOCKSPEC stores every step when you press the SET button All the settings will be stored in the speed controls memory even if the speed control will be disconnected from the battery TRANSMITTER SETTINGS Setup the following basic functions on your transmitter if available Throttle travel High ATV EPA maximum Brake travel maximum Throttle exponential start with 0 Ne
22. utral trim centre Servo reverse any setting don t change after set up procedure If your transmitter doesn t offer any of above functions it s already in basic setup mode e Ensure that the speed control is not connected to the drive battery and is switched off e Remove motor pinion or ensure that the wheels of the model are free to rotate e Switch the transmitter on and set the transmitter throttle stick to neutral e Connect the speed control to the battery and switch the unit on e Hold the SET button pressed for at least 3sec using the supplied plastic screwdriver gt You entered setup mode and the SET LED flashes blue it will flash until the setup is completed e Leave transmitter in neutral position and press the SET button once gt Neutral setting is stored MODE LED flashes yellow and the motor beeps e Hold full throttle on transmitter and press the SET button once gt Full throttle setting is stored MODE LED flashes red e Hold full brake on transmitter and press the SET button once gt Brake setting is stored LED s glow red MODE and blue SET This completes the setup procedure and your LRP SPX COMPETITION StockSpec is ready to use If you make a mistake during the setup procedure don t worry Disconnect the battery for about 10sec and start again from the first step At the end of each run switch of the car and then switch off the transmitter At the start of each run switch on the transmit
Download Pdf Manuals
Related Search