Home

DSL-302T ADSL Modem User`s Manual - D-Link

1. DSL 302T ADSL Modem User s Manual First Edition February 2004 651DSL302T01 DSL 302T DSL Modem User s Guide FCC Warning This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help
2. DSL 302T ADSL Modem User s Guide Hardware Installation The DSL 302T maintains three separate interfaces an Ethernet a USB and an ADSL interface Place the Modem in a location where it can be connected to the various devices as well as to a power source The Modem should not be located where it will be exposed to moisture or excessive heat Make sure the cables and power cord are placed safely out of the way so they do not create a tripping hazard As with any electrical appliance Observe common sense safety procedures The access point can be placed on a shelf or desktop ideally you should be able to see the LED indicators on the front if you need to view them for troubleshooting Power on Modem CAUTION The Modem must be used with the power adapter included with the device To power on the Modem 1 Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the Modem and plug the adapter into a suitable nearby power source 2 You should see the Power LED indicator light up and remain lit The Status LED should light solid green and begin to blink after a few seconds 3 Ifthe Ethernet port is connected to a working device check the Ethernet Link Act LED indicators to make sure the connection is valid The Modem will attempt to establish the ADSL connection if the ADSL line is connected and the Modem is properly configured this should light up after several seconds If this is the first time in
3. can adjust the IP settings for the Modem to fit within your existing scheme Using the Default IP Address The Modem is shipped with a preset default IP address setting of 192 168 1 1 for the LAN port There are two ways to use this default IP address you can manually assign an IP address and subnet mask for each PC on the LAN or you can instruct the Modem to automatically assign them using DHCP The simplest method is to use DHCP The DHCP function is active by default Manual IP Address Assignment Manually configuring IP settings for the LAN means you must manually set an IP address subnet mask and IP address of the default gateway the Modem s IP address on each networked computer The example listed below describes IP configuration for computers running Windows 95 or Windows 98 Regardless of what operating system is used on each workstation the three network IP settings must be defined so the network interface used by each workstation can be identified by the Modem and vice versa For detailed information about configuring your workstations IP settings consult the user s guide included with the operating system or the network interface card NIC 1 In Windows 95 98 click on the Start button go to Settings and choose Control Panel 2 Inthe window that opens double click on the Network icon 3 Under the Configuration tab select the TCP IP component and click Properties 4 Choose the Specify an IP address option and edit the addr
4. such as a Modem or similar firewall hardware The IP address can be assigned in a number of ways Your network service provider will give you instructions about any additional connection software or NIC configuration that may be required DSL 302T ADSL Modem User s Guide Modem Features The DSL 302T ADSL Modem utilizes the latest ADSL enhancements to provide a reliable Internet portal suitable for most small to medium sized offices DSL 302T advantages include PPP Point to Point Protocol Security The DSL 302T ADSL Modem supports PAP Password Authentication Protocol and CHAP Challenge Handshake Authentication Protocol for PPP connections DHCP Support Dynamic Host Configuration Protocol automatically and dynamically assigns al LAN IP settings to each host on your network This eliminates the need to reconfigure every host whenever changes in network topology occur Network Address Translation NAT For small office environments the DSL 302T allows multiple users on the LAN to access the Internet concurrently through a single Internet account This provides Internet access to everyone in the office for the price of a single user NAT improves network security in effect by hiding the private network behind one global and visible IP address NAT address mapping can also be used to link two IP domains via a LAN to LAN connection TCP IP Transfer Control Protocol Internet Protocol The DSL 302T supports TCP IP protocol
5. 0 to 191 254 0 0 65 534 SR 2 097 150 192 0 1 0 to 223 255 254 0 Note All network addresses outside of these ranges Class D and E are either reserved or set aside for experimental networks or multicasting When an IP address s host portion contains only zero s the address identifies a network and not a host No physical device may be given such an address The network portion must start with a value from 1 to 126 or from 128 to 223 Any other value s in the network portion may be from 0 to 255 except that in class B the network addresses 128 0 0 0 and 191 255 0 0 are reserved and in class C the network addresses 192 0 0 0 and 223 255 255 0 are reserved The value s in the host portion of a physical device s IP address can be in the range of 0 through 255 as long as this portion is not all O or all 255 Values outside the range of 0 to 255 can never appear in an IP address 0 to 255 is the full range of integer values that can be expressed with eight bits The network portion must be the same for all the IP devices on a discrete physical network a single Ethernet LAN for example or a WAN link The host portion must be different for each IP device or to be more precise each IP capable port or interface connected directly to that network The network portion of an IP address will be referred to in this manual as a network number the host portion will be referred to as a host number To connect to the Internet or to
6. DSL 302T ADSL Modem User s Guide Management IP The IP address of the modem may be changed but remember to take note of the new settings A valid IP address and subnet mask are needed to access the Web manager Ws ad cree pr gef ra is changed yog will reed da bere fie new I does be stie fio use Vu iab Brgses pr tor St 63 sing wur Vids Pages IP Aiperg iar teat Lo EC Re Dat uri Crafpsage SE Hasire c HER Parmae eng o o doply Cancel Figure 4 2 Setup Management IP window Make any desired changes then click Apply 27 DSL 302T ADSL Modem User s Guide Tools Changing the User Name and Password Before you configure the Modem and connect to the WAN you should change the user name and password used to access the web based manager Click on the Tools tab to access the Tools menu Status Help The Tit section alique vou wa Sas ma configuration restart the gabeveay update the gabesan Terrewarg setup usar ant rama hog Infarmation and run Ping ang QAM tesis System Commands Belecl ta Save Tha current roig aior Rested Be gatevwas and Restore o factor defaults Hemots D eu Select to satup Femat Lag Information User Managment Selaci to configure Pas nare and passer Update Gateway Select to upgrade the Gateway Firman Ping Tesi Sefer to run a Ping Tash OAB Tee Select to Check whether the router eth a specific Cann chan rs propery rn ed bo lhe Hebssge k Figure 4 3 Opening To
7. IP Information Windows 95 98 If TCP IP does not display as an installed component click Add The Select Network Component Type dialog box displays Select Protocol and then click Add The Select Network Protocol dialog box displays Click on Microsoft in the Manufacturers list box and then click TCP IP in the Network Protocols list box Click OK to return to the Network dialog box and then click OK again You may be prompted to install files from your Windows 95 98 installation CD Follow the instructions to install the files Click OK to restart the PC and complete the TCP IP installation DSL 302T ADSL Modem User s Guide Configure Windows 95 and Windows 98 for DHCP A eg 7 Open the Control Panel window and then click the Network icon Select the network component labeled TCP IP and then click Properties If you have multiple TCP IP listings select the listing associated with your network card or adapter In the TCP IP Properties dialog box click the IP Address tab Click the Obtain an IP address automatically option Double click OK to confirm and save your changes You will be prompted to restart Windows Click Yes When it has restarted your computer is ready to use the Modem s DHCP server Windows NT 4 0 Workstations First check for the IP protocol and if necessary install it 1 2 3 4 eA 8 In the Windows NT task bar click the Start button point to Settings and then click Control
8. If you are interested in more advanced information on how to use IP addressing on a LAN there are numerous resources freely available on the Internet There are also many books and chapters of books on the subject of IP address assignment IP networking and the TCP IP protocol suite 46 DSL 302T ADSL Modem User s Guide C IP Concepts This appendix describes some basic IP concepts the TCP IP addressing scheme and show how to assign IP Addresses When setting up the Modem you must make sure it has a valid IP address Even if you will not use the WAN port ADSL port you should at the very least make sure the Ethernet LAN port is assigned a valid IP address This is required for telnet in band SNMP management and related functions such as trap handling and TFTP firmware download IP Addresses The Internet Protocol IP was designed for routing data between network sites all over the world and was later adapted for routing data between networks within any site often referred to as subnetworks or subnets IP includes a system by which a unique number can be assigned to each of the millions of networks and each of the computers on those networks Such a number is called an IP address To make IP addresses easy to understand the originators of IP adopted a system of representation called dotted decimal or dotted quad notation Below are examples of IP addresses written in this format 201 202 203 204 189
9. Panel In the Control Panel window double click the Network icon In the Network dialog box click the Protocols tab The Protocols tab displays a list of currently installed network protocols If the list includes TCP IP then the protocol has already been enabled Skip to Configure IP Information If TCP IP does not display as an installed component click Add In the Select Network Protocol dialog box select TCP IP and then click OK You may be prompted to install files from your Windows NT installation CD or other media Follow the instructions to install the files After all files are installed a window displays to inform you that a TCP IP service called DHCP can be set up to dynamically assign IP information Click Yes to continue and then click OK if prompted to restart your computer Configure Windows NT 4 0 for DHCP Qucm decus Open the Control Panel window and then double click the Network icon In the Network dialog box click the Protocols tab In the Protocols tab select TCP IP and then click Properties In the Microsoft TCP IP Properties dialog box click the Obtain an IP address automatically option Click OK twice to confirm and save your changes and then close the Control Panel Access the Configuration Manager Now that your computer s IP settings allow it to communicate with the Modem you can access the configuration software Note Be sure that the web browser on your computer is not configured to
10. any private IP network that uses an Internet assigned network number you must obtain a registered IP network number from an Internet authorized network information center In many countries you must apply through a government agency however they can usually be obtained from your Internet Service Provider ISP If your organization s networks are and will always remain a closed system with no connection to the Internet or to any other IP network you can choose your own network numbers as long as they conform to the above rules If your networks are isolated from the Internet e g only between your two branch offices you can assign any IP Addresses to hosts without problems However the Internet Assigned Numbers Authority IANA has reserved the following three blocks of IP Addresses specifically for private stub networks Beginning Address Ending Address 10 0 0 0 10 255 255 255 172 16 0 0 172 31 255 255 C 192 168 0 0 192 168 255 255 It is recommended that you choose private network IP Addresses from the above list For more information on address assignment refer to RFC 1597 Address Allocation for Private Internets and RFC 1466 Guidelines for Management of IP Address Space 48 DSL 302T ADSL Modem User s Guide Subnet Mask In the absence of subnetworks standard TCP IP addressing may be used by specifying subnet masks as shown below Subnet mask settings other than those listed above add significance to the i
11. au E MAIL support dlink com au amp info dlink com au D Link Brasil Ltda Edificio Manoel Tabacow Hydal Rua Tavares Cabral 102 Sala 31 05423 030 Pinheiros Sao Paulo Brasil TEL 55 11 3094 2910 to 2920 FAX 55 11 3094 2921 E MAIL efreitas dlink cl D Link Canada 2180 Winston Park Drive Oakville Ontario L6H 5W1 Canada TEL 1 905 829 5033 FAX 1 905 829 5095 TOLL FREE 1 800 354 6522 URL www dlink ca FTP ftp dlinknet com E MAIL techsup dlink ca D Link South America Sudam rica Isidora Goyenechea 2934 Of 702 Las Condes Fono 2323185 Santiago Chile S A TEL 56 2 232 3185 FAX 56 2 232 0923 URL www dlink cl E MAIL ccasassu dlink cl amp tsilva dlink cl D Link China 15 Floor Science amp Technology Tower No 11 Baishiqiao Road Haidan District 100081 Beijing China TEL 86 10 68467106 FAX 86 10 68467110 URL www dlink com cn E MAIL liweii digitalchina com cn D Link Denmark Naverland Denmark Naverland 2 DK 2600 Glostrup Copenhagen Denmark TEL 45 43 969040 FAX 45 43 424347 URL www dlink dk E MAIL info dlink dk D Link Middle East 7 Assem Ebn Sabet Street Heliopolis Cairo Egypt TEL 202 245 6176 FAX 202 245 6192 URL www dlink me com E MAIL support dlink me com amp fateen dlink me com D Link Finland Pakkalankuja 7A FIN 0150 Vantaa Finland TEL 358 9 2707 5080 FAX 358 9 2707 5081 URL www dlink fi com D Link France Le Florilege No 2 All e de la Fresneri
12. dons piya Are SR ER nius Hariak Termine ater m cpresscuties Dies Coercion eee 5 gie pf Fum ra imd Bei Deiere Crezbrzarerbar as rs Gef angie RE Waster a all fo DEL c bnnc bon can Er be Hrs aq rika vola Dual ask DH pagic 30 0H i Con O n Topp Febris Th neinereum RT il up Ha 1 28 Erfrrcs MEE Check fhe hpa i yu papari p ce probos a opena re fe emei meer a PPP DE connection Ten fabre wii foe ai TOP aie la condom win PPP ISI be rara TOP Hoss Degqnari tus ie PPP Mug Debat Erabigs FPP raras kin apup ag facies Figure 4 17 Opening Help window Click on the item you want further information for on the window above 42 DSL 302T ADSL Modem User s Guide GENERAL ITU G 992 1 G dmt RFC 1661 PPP ITU G 992 2 G lite RFC 1994 CHAP ITU G 994 1 G Hs RFC 1334 PAP ITU T Rec 1 361 RFC 2364 PPP over ATM ITU T Rec 1 610 RFC 1877 Automatic IP IEEE 802 3 assignment standards IEEE 802 3u RFC 2516 PPP over Ethernet Supports RFC 2131 and RFC IEEE 802 1d 2132 DHCP RFC 1213 compliant Compatible with all T1 413 RFC 1483 Bridged Ethernet issue 2 full rate DMT over analog POTS and CO DSLAM RFC 1577 IP over ATM equipment Supports ATM Forum UNI V3 1 TCP IP Protocols PVC G dmt full rate Downstream up to 8 Mbps Data Transfer Upstream up to 640 Kbps Rate G lite Downstream up to 1 5 Mbps Upstream up to 512 Kbps RJ 11 port ADSL telephone line connection Media Interface RJ 45 port
13. for 10 100BASET Ethernet connection 43 DSL 302T ADSL Modem User s Guide DC Inputs Power Adapter Power Consumption Operating Temperature Humidity Dimensions Safety Reliability Physical and Environmental Input 100V 240V AC 50 60Hz Output 9V AC 1A 5 to 40 C 41 104 F 5 to 95 non condensing 142 W x 117 D x 31 H mm CE Class B FCC Class B CSA 950 UL 1950 IEC 60950 EN 60950 Mean Time Between Failure MTBF min 4 years 44 DSL 302T ADSL Modem User s Guide IP Address Setup The DSL 302T is designed to provide network administrators maximum flexibility for IP addressing on the Ethernet LAN The easiest IP setup choice in most cases is to let the Modem do it using DHCP which is enabled by default This appendix briefly describes various options including DHCP used for IP setup on a LAN If you are new to IP networking the next appendix provides some background information on basic IP concepts Assigning Network IP Addresses The IP address settings which include the IP address subnet mask and gateway IP address are the first and most important internal network settings that need to be configured The Modem is assigned a default LAN IP address and subnet mask If you do not have a preexisting IP network and are setting one up now using the factory default IP address settings can greatly ease the setup process If you already have a preexisting IP network you
14. menu before you can change the required settings PPoA To configure the WAN connection for PPPoA perform the steps listed below Some settings may not be required to be changed now but can be changed later if you choose Tools Status E PP Ped Conmaciien Sonali EE Hemi inn H PPPu amp B X Ten PPPoA Encapaulaian E Ltr 7 ww T Geen W Sena Sek p LH ori aT E ju remm Wi s rand dec LER z Ecg Ka e p kepie In mun scm bpi EM SS EE pec a SH m e P Figure 3 4 Setup New Connection PPPoA window PPPoA is also known as RFC 2364 It is a method of encapsulating PPP packets over ATM cells that are carried over the DSL line PPP or Point to Point protocol is a method of establishing a network connection session between network hosts PPPoA connection require a verification process where it is necessary to enter a Username and Password to connection the Modem to the Internet DSL 302T ADSL Modem User s Guide To setup a PPPoA connection for the first time 1 2 3 Type in a Name in the space provided if you wish or leave the default name Make sure PPPoA appears listed as the Type of connection protocol used Do not change the VPI or VCI values unless you are required to do so If these settings are incorrect the ADSL connection will not function Many users will be able to use the default settings If you are told to change these type in the values given to yo
15. see the Found New Hardware message window followed shortly after by the opening Found New Hardware Wizard window Ir cared Siew Hardware iard Welcome to the Found New Hardware Wizard The wired haips you maa cereis demens for s haidwane deai T contenue chick Hast oe e cem 3 If you do not see the auto run window pictured above explore the CD and double click the inf file DLink 302t inf 4 Click the Next button Found ken hiar drar OOOO intal Heder aream Doreen A desace dtas rt coli papua Pit enables 5 i andes devene bo soh rei an real Goaler Ire mirad sil compete Ue nel allen For has diee e DeLana A deact dive a 5 bobus proga thal rakes alhada esci work windows mead droe flac for pour reng denice Tic locale droe haz and complete tha inelaishon click Mew Wat do pour mant fee szad ka da e be a ng derer ka mg ran Dipl a isi of Pe kroan drana For Eni deseos so thal can choose m wech ann tik Met ee 5 Click the Next button DSL 302T DSL Modem User s Guide Locate Driver Files Where do pou qanri Windows bo zech ioa dine fles Feah ka Are Heg ka tha Folien ua an device u ges The szad searches for suitable Aust E ils dies database on vour computer and in Ta stat the sesch click Het If pou se sesch on x Hoppe dick e CRM dire Feel tha kee dat or CD beh ckkee Het Check CD ROM drives as shown above if you are using the USB driver included on th
16. the language used for the Internet It is compatible with access servers manufactured by major vendors ATM Asynchronous Transfer Mode The DSL 302T supports Bridged Ethernet over ATM RFC1483 IP over ATM RFC1577 and PPP over ATM RFC 2364 Precise ATM Traffic Shaping Traffic shaping is a method of controlling the flow rate of ATM data cells This function helps to establish the Quality of Service for ATM data transfer G hs Auto handshake This allows the Modem to automatically choose either the G lite or G dmt ADSL connection standards High Performance Very high rates of data transfer are possible with the Modem Up to eight Mbps downstream bit rate using the G dmt Easy Installation The DSL 302T uses a web based graphical user interface program for convenient management access and easy set up Any common web browser software can be used to manage the Modem DSL 302T ADSL Modem User s Guide Standards Compatibility and Compliance The DSL 302T complies with or is compatible with the following standards as recognized by their respective agencies ITU G 992 2 G lite Splitterless ADSL compliant ITU T Rec 1 361 compliant RFC 791 Internet Protocol compliant RFC 792 UDP compliant RFC 1334 PPP Authentication Protocol compliant RFC 1483 IP over AALS Bridged Ethernet over AALS compliant RFC 1557 Classical IP over ATM IPoA compliant RFC 1661 Point to Point Protocol PPP compliant RFC 1877 Automat
17. to load previously saved configuration files on the device To save the current settings to a configuration file on your computer type in the full name and path in the Select a Configuration file space or click on the Browse button to search for the file Click the Back Up button to initiate this action To load a saved configuration file from the computer type in the full name and path in the Select a Configuration file space or click on the Browse button to search for the file Click the Restore button to initiate this action 32 DSL 302T ADSL Modem User s Guide Ping Test Fra eg rang do semi Ringo pos beim do i m ac png ne eon Te inb med Grier E zirirss u krna 192 168 D Pura Sog ma Lr Sumber pi S ri equate i dE ATERT pru meris liebeork mounts EE RR Figure 4 8 Tools Ping Test window This window is used to test the connection path of the Modem to another networked device with an IP address To Ping a device first enter the IP address of the device that you wish to Ping into the first field the Packet Size in bytes in the second field and finally enter the number of times you wish the Ping function to attempt a connection to the desired device into the third field Click Test to start the Ping mechanism The results of the Ping will be shown in the result box in the bottom half of the window 33 DSL 302T ADSL Modem User s Guide OAM Test The OAM Test menu is used to check connec
18. 21 241 56 125 87 0 1 Each of the four values in an IP address is the ordinary decimal base 10 representation of a value that a computer can handle using eight bits binary digits 1s and Os The dots are simply convenient visual separators Zeros are often used as placeholders in dotted decimal notation 189 21 241 56 can therefore also appear as 189 021 241 056 IP networks are divided into three classes on the basis of size A full IP address contains a network portion and a host device portion The network and host portions of the address are different lengths for different classes of networks as shown in the table below B 18 24 3 Class A JU dE Class B me nostid casse fifi fo hostid cesso BERT Casas 7 csse TTE T emeritus ee 47 DSL 302T ADSL Modem User s Guide Networks attached to the Internet are assigned class types that determine the maximum number of possible hosts per network The previous figure illustrates how the net and host portions of the IP address differ among the three classes Class A is assigned to networks that have more than 65 535 hosts Class B is for networks that have 256 to 65534 hosts Class C is for networks with less than 256 hosts IP Network Classes Class Maximum Number Network Addresses Host Maximum Number of of Networks in Portion in Parenthesis Hosts per Network Class 1 0 0 0 to 126 0 0 0 16 777 214 Es 16 382 128 1 0
19. CE Mark Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures ii DSL 302T ADSL Modem User s Guide LIMITATION OF LIABILITY IN NO EVENT WILL D LINK BE LIABLE FOR ANY DAMAGES INCLUDING LOSS OF DATA LOSS OF PROFITS COST OF COVER OR OTHER INCIDENTAL CONSEQUENTIAL OR INDIRECT DAMAGES ARISING OUT THE INSTALLATION MAINTENANCE USE PERFORMANCE FAILURE OR INTERRUPTION OF A D LINK PRODUCT HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY THIS LIMITATION WILL APPLY EVEN IF D LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE IF YOU PURCHASED A D LINK PRODUCT IN THE UNITED STATES SOME STATES DO NOT ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU Limited Warranty Hardware D Link warrants each of its hardware products to be free from defects in workmanship and materials under normal use and service for a period commencing on the date of purchase from D Link or its Authorized Reseller and extending for the length of time stipulated by the Authorized Reseller or D Link Branch Office nearest to the place of purchase This Warranty applies on the condition that the product Registration Card is filled out and returned to a D Link office within ninety 90 days of purchase A list of D Link offices is provided at the back of this manual to
20. EB BASED MANAGEMENT U T 25 Accessing the Web Managers i enano aco e ed a po eec ete o RD Ae q huuu arches 25 DHCP ConfiBUration 2 o nre eie ter et rg e terre al REGERE RR C ai eee P HEP ER E Ree eed 26 Management IP nnne se S un RR ROT 27 r 28 Changing the User Name and Password esee nennen trennen inneren tnnne nenne nnne 28 User Management eR ted od RN 29 System Commands ode b n de tee ORE e E petere inepte eite dien 30 Remote oea oce ttt ener RR etn eno B Er 31 Update Gateway corea ea e es rene peer E EEEE E VEE EEEE SEENEN 32 GET 35 Network Statistics RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRMMEEEMMMMM 36 Connection Stai EE 37 EEGEN 38 en BEE 39 See e ie DEE 40 System LO E Q 4l gl m D 42 TECHNICAL SPECIFICATIONS tt 43 IP ADDRESS SETUP MEEPMZKER u u u 45 Seel 09 EE 47 DSL 302T DSL Modem User s Guide About This User s Guide This user s guide provides instructions on how to install the DSL 302T ADSL Modem and use it to connect a computer or Ethernet Local Area Network LAN to the Internet If you are using a computer with a functioning Ethernet p
21. In the Network Connections window right click on LAN Local Area Connection then click Properties 11 DSL 302T ADSL Modem User s Guide 3 Aeheork Connect izre F r ER Via P lache Adbessdl rie Rides WE Mate k Crrractiona Hhrkssork Tanku s Cragin m runa CRT D Zei op clown era nitie penari L EC re MA beten me comer wi D asras fei dte To KO Ves ER Or te arto Change pete pl ze uyana DR rr Pla es EF Gegen pel Me Voters Places C Pv Documents E Piy Coruga a In the General tab of the Local Area Connection Properties menu highlight Internet Protocol TCP IP under This connection uses the following items by clicking on it once Click on the Properties button Local Area Connection 3 Properties General Authentication Advanced Connect using Sai Intel R PRO 100 VE Network Connection This connection uses the following items el Client for Microsoft Networks 8 File and Printer Sharing for Microsoft Networks dl QoS Packet Scheduler Internet Protocol TCP IP Description Transmission Control Protocol Internet Protocol The default wide area network protocol that provides communication across diverse interconnected networks C Show icon in notification area when connected Tox mm 12 DSL 302T ADSL Modem User s Guide 4 Select Obtain an IP address automatically by clicking once in the circl
22. MAIL Wxavier dlink me com D Link Europe United Kingdom Ltd 4b Floor Merit House Edgware Road Colindale London NW9 5AB United Kingdom TEL 44 020 8731 5555 SALES 44 020 8731 5550 FAX 44 020 8731 5511 SALES 44 020 8731 5551 BBS 44 0 181 235 5511 URL www dlink co uk E MAIL info dlink co uk D Link U S A 17575 Mt Herrmann Fountain Valley CA 92708 TEL 1 714 885 6000 FAX 1 866 743 4905 INFO 1 800 326 1688 URL www dlink com E MAIL tech dlink com amp support dlink com Registration Card Print type or use block letters Your name Mr Ms Organization Dept Your title at organization Telephone Fax Organization s full address Country Date of purchase Month Day Year Product Product Serial No Product installed in type of Product installed in computer serial No m DDR Compaq Pe e g Compaq 486 Applies to adapters only Product was purchased from Reseller s name Telephone Fax Reseller s full address Answers to the following questions help us to support your product 1 Where and how will the product primarily be used OHome OOffice OTravel LICompany Business LIHome Business OPersonal Use 2 How many employees work at installation site L11 employee L12 9 L110 49 050 99 L1100 499 0500 999 L11000 or more 3 What network protocol s does your organization use LIXNS IPX LITCP IP LIDECnet OOthers 4 What network operating system s does yo
23. any PC within the same subnet as the Modem to access the web based manger i Do not confuse the user name and password used to access the web based manager with the ADSL account user name and password needed for PPP Note connections to access the service provider s network DSL 302T ADSL Modem User s Guide Configure the Modem The first page that appears after you successfully login displays information about the Modem and its connection status Tabs across the top of the screen show other available menus Home Setup Tools Status and Help selup Tools Balam Ligiina hbureh d rrararkarsh De Gu Disrpnneried kh pra LU perna aim D kipe Lc Speed Dipwrerkeam LAN E Adda su 13z 18B 1 1 Ehr Gonreried Lee DpSromergn DHCF Sever Running Botan Versi V DBI TI amp ELLO EHI 1717 LEX EI Figure 3 2 Home Status Information window When the Modem is used to provide Internet access it must first access your service provider s network that is it must communicate with computers and other modems owned by your service provider These computers and modems then provide access to the Internet The Modem must be configured to communicate with the systems that give it access to the larger network Click either the Setup tab or the Go to setup wizard hyperlink the following window will appear 17 DSL 302T ADSL Modem User s Guide Setup The Setup window offers links to menus to configure settings fo
24. ay also be connected through the USB port The ADSL connection is made using ordinary twisted pair telephone line with standard connectors Multiple PCs can be networked and connected to the Internet using a single Wide Area Network WAN interface and single global IP address What is ADSL Asymmetric Digital Subscriber Line ADSL is an access technology that utilizes ordinary copper telephone lines to enable broadband high speed digital data transmission and interactive multimedia applications for business and residential customers ADSL greatly increases the signal carrying capacity of copper telephone lines without interfering with regular telephone services For the ADSL user this means faster downloads and more reliable connectivity ADSL devices make it possible to enjoy benefits such as high speed Internet access without experiencing any loss of quality or disruption of voice fax telephone capabilities ADSL provides a dedicated service over a single telephone line operating at speeds of up to 8 Mbps downstream and up to 640 Kbps upstream depending on local telephone line conditions A secure point to point connection is established between the user and the central office of the service provider D Link ADSL devices incorporate the recommendations of the ADSL Forum regarding framing data format and upper layer protocols Low Pass Filters Since ADSL and telephone services share the same copper wiring to carry their respective signal
25. ccessing the Web Manager In order to use the web based management software it will be necessary to use a computer that occupies the same subnet as the Modem The simplest way to do this for many users will be to use DHCP server that is enabled by default on the Modem You may also specify IP settings for your computer The Modem has a default IP address of 192 168 1 1 and a subnet mask of 255 255 255 0 Once you have accessed the configuration software you can configure the Modem s IP settings and DHCP server configuration to suit your preferences To use the web based management software run the browser you have installed on your computer and direct it to the Modem s HTML interface using its LAN IP address If this is the first time you are accessing the web based manager you must type its default IP address 192 168 1 1 in the address bar of the browser The URL in the address bar should read http 192 168 1 1 If you change the IP address you will use the new IP address to access the web based manager A new window will appear and you will be prompted for a user name and password Use default user name admin and password admin for first time set up Note Be sure that the web browser on your computer is not configured to use a proxy server in the Internet settings In Windows Internet Explorer you can check if a proxy server is enabled using the following procedure 1 In Windows click on the Start button go to Settings and choose Control Pane
26. d using a web browser To access the management software your computer must be able to see the Modem Your computer can see the Modem if it is in the same neighborhood or subnet as the Modem This is accomplished by making sure your computer has IP settings that place it in the same subnet as the Modem The easiest way to make sure your computer has the correct IP settings is to configure it to use the embedded DHCP server in the Modem The next section describes how to change the IP configuration for a computer running a Windows operating system to be a DHCP client 2 Configure the WAN Connection Once your are able to access the configuration software you can proceed to change the settings required to establish the ADSL connection and connect to the service providers network There are different methods used to establish the connection to the service provider s network and ultimately to the Internet You should know what Encapsulation and connection type you are required to use for your ADSL service For some users it may be necessary to change the PVC settings used for the ADSL connection Your service provider should provide all the information you need to successfully configure the WAN connection Configuring IP Settings on Your Computer In order to configure your system to receive IP settings from the Modem it must first have the TCP IP protocol installed If you have an Ethernet port on your computer it probably already has TCP IP protocol in
27. e 78330 Fontenay le Fleury France TEL 33 1 3023 8688 FAX 33 1 3023 8689 URL www dlink france fr E MAIL info dlink france fr D Link Central Europe D Link Deutschland GmbH Schwalbacher Strasse 74 D 65760 Eschborn Germany TEL 49 6196 77990 FAX 49 6196 7799300 URL www dlink de BBS 49 0 6192 971199 analog BBS 49 0 6192 971198 ISDN INFO 00800 7250 0000 toll free HELP 00800 7250 4000 toll free REPAIR 00800 7250 8000 E MAIL info dlink de India Italy Japan Netherlands Norway Russia Singapore South Africa Spain Sweden Taiwan Turkey U A E D Link India Plot No 5 Bandra Kurla Complex Rd Off Cst Rd Santacruz East Mumbai 400 098 India TEL 91 022 652 6696 6578 6623 FAX 91 022 652 8914 8476 URL www dlink india com amp www dlink co in E MAIL service dlink india com amp tushars dlink india com D Link Mediterraneo Srl D Link Italia Via Nino Bonnet n 6 B 20154 Milano Italy TEL 39 02 2900 0676 FAX 39 02 2900 1723 URL www dlink it E MAIL info dlink it D Link Japan 10F 8 8 15 Nishi Gotanda Shinagawa ku Tokyo 141 Japan TEL 81 3 5434 9678 FAX 81 3 5434 9868 URL www d link co jp E MAIL kida d link co jp D Link Benelux Fellenoord 130 5611 ZB Eindhoven The Netherlands TEL 31 40 2668713 FAX 31 40 2668666 URL www d link benelux nl amp www dlink benelux be E MAIL info dlink benelux nl amp info dlink benelux be D Link Norway Waldema
28. e Click the OK button Internet Protocol TCP IP Properties p General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Use the following IP address Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server 172 40 Alternate DNS server Ae 10 35 Your computer is now ready to use the Modem s DHCP server Windows 2000 First check for the IP protocol and if necessary install it 1 Inthe Windows task bar click the Start button point to Settings and then click Control Panel 2 Double click the Network and Dial up Connections icon 3 Inthe Network and Dial up Connections window right click the Local Area Connection icon and then select Properties 4 The Local Area Connection Properties dialog box displays with a list of currently installed network components If the list includes Internet Protocol TCP IP then the protocol has already been enabled skip ahead to Configure Windows 2000 for DHCP If Internet Protocol TCP IP does not display as an installed component click Install In the Select Network Component Type dialog box select Protocol and then click Add Select Internet Protocol TCP IP in the Network Protocols list and then click OK pe l v eA You may be prompted to
29. e CD ROM that came with your Modem Click Next Found ew Haridbeari Wixarndl Completing the Found New Hardware Wizard D Link USE Peace HD IS Hotak Desa Windows has Rrarhed inctaling Pe pihage or hir dence T cune Uis vd click Fines Connect the Ethernet cable if you have not done so Connect the ADSL cable if you have not done so Remember that most ADSL installations require a filter to divide the ADSL signal from the Plain Old Telephone POTS signal You can restart your computer now by clicking the Finish button The computer will be able to connect to the Modem through the USB port after restarting xi DSL 302T ADSL Modem User s Guide Introduction This section provides a brief description of the Modem its associated technologies and a list of Modem features Modem Description and Operation The DSL 302T ADSL Modem is designed to provide a simple and cost effective ADSL Internet connection for individual computers through either the Ethernet or USB ports or use it to bridge your Ethernet LAN to the Internet The DSL 302T combines the benefits of high speed ADSL technology and LAN IP management in one compact and convenient package ADSL technology enables many interactive multi media applications such as video conferencing and collaborative computing The Modem is easy to install and use The DSL 302T connects to single computer or an Ethernet LAN via a standard Ethernet interface A single computer m
30. ently marked on the outside of the package The package must be mailed or otherwise shipped to D Link with all costs of mailing shipping insurance prepaid D Link shall never be responsible for any software firmware information or memory data of Purchaser contained in stored on or integrated with any product returned to D Link pursuant to this warranty Any package returned to D Link without an RMA number will be rejected and shipped back to Purchaser at Purchaser s expense and D Link reserves the right in such a case to levy a reasonable handling charge in addition mailing or shipping costs Software Warranty service for software products may be obtained by contacting a D Link office within the applicable warranty period A list of D Link offices is provided at the back of this manual together with a copy of the Registration Card If a Registration Card for the product in question has not been returned to a D Link office then a proof of purchase such as a copy of the dated purchase invoice must be provided when requesting warranty service The term purchase in this software warranty refers to the purchase transaction and resulting license to use such software D Link warrants that its software products will perform in substantial conformance with the applicable product documentation provided by D Link with such software product for a period of ninety 90 days from the date of purchase from D Link or its Authorized Reseller D Link warrant
31. ess settings accordingly Consult the table below for IP settings on a Class C network Using Default IP without DHCP ost IP Address Subnet Mask Gateway IP Modem 192 168 1 1 255 255 255 0 Computer 1 192 168 1 2 255 255 255 0 192 168 1 1 Computer 2 192 168 1 3 255 255 255 0 192 168 1 1 Computer 3 192 168 1 4 255 255 255 0 192 168 1 1 IP Setup Example 1 Please note that when using the default IP address as in the above example the first three numbers in the IP address must always be the same with only the fourth number changing The first three numbers define the network IP address all machines must belong to the same IP network while the last number denotes the host IP 45 DSL 302T ADSL Modem User s Guide address each computer must have a unique address to distinguish it on the network The IP address scheme used in Example 1 can be used for any LAN that requires up to 253 separate IP addresses excluding the Modem Notice that the subnet mask is the same for all machines and the default gateway address is the LAN IP address of the Modem Itis a good idea to make a note of each device s IP address for reference during troubleshooting or when adding new stations or devices Using DHCP The second way to use the default settings is to allow the Modem to automatically assign IP settings for workstation using DHCP To do this simply make sure your computers IP addresses are set to 0 0 0 0 under Wind
32. etup Change connection Mame com 1 PPPoA B5 Tow PPPoE IPP type here PPP Satin fw Senimi Ss en ere husercena WPI B Passed WI 145 Gol LUES keep Ane bn mr PCR Was Fail H Huez BOR bii M bp NRU Jha byter Apply Cancel Figure 3 5 Setup Connection PPPoE window To configure a PPPoE connection perform the steps listed below Some settings may not be required to be changed now but can be changed later if you choose 1 Type ina Name in the space provided if you wish or leave the default name 2 Make sure PPPoE appears listed as the Type of connection protocol used 3 Do not change the VPI or VCI values unless you are required to do so If these settings are incorrect the ADSL connection will not function Many users will be able to use the default settings If you are told to change these type in the values given to you by your service provider 4 Leave the default QoS values if you are unsure or the ISP did not provide this information 5 Do not change the PCR or SCR values unless you are required to do so If you are told to change these type in the values given to you by your service provider 6 Supply a Username and Password used to verify the identity of your account These are usually provided by your ISP 21 DSL 302T ADSL Modem User s Guide 7 The Encapsulation values LLC SNAP and VC MUX are two different methods of encapsulating the PPP packet Contact your ISP to
33. fferent methods of encapsulating the PPP packet Contact your ISP to make sure which encapsulation is being supported Based on the information provided by your ISP enter the IP Address Subnet Mask Default Gateway Gf provided and Domain Name Services DNS values if provided Click the Apply button when you have entered all the information The web browser will briefly go blank You are now finished changing setting for the primary WAN connection known as Connection 1 It is now necessary to save the changes you just made and restart the Modem To save the changes made to Connection 1 click the Tools tab and then click on the System Commands button Click on the Save All button to store the configuration settings Click on Back button to return to the System Commands menu Check the WAN connection status Click the Status tab and then the Connection Status button Look under WAN to view the State of Connection 1 it should read Connected If the WAN connection state does not appear to Connected after a few minutes go back to the Connection 1 Setup menu check the settings and make sure they are correct 24 DSL 302T ADSL Modem User s Guide Web based Management The DSL 302T offers a web based HTML graphical user interface allowing users to manage the Modem from anywhere on the LAN using a standard browser A web browser is used to communicate directly with the Modem and make changes to the configuration or monitor status A
34. gether with a copy of the Registration Card If the product proves defective within the applicable warranty period D Link will provide repair or replacement of the product D Link shall have the sole discretion whether to repair or replace and replacement product may be new or reconditioned Replacement product shall be of equivalent or better specifications relative to the defective product but need not be identical Any product or part repaired by D Link pursuant to this warranty shall have a warranty period of not less than 90 days from date of such repair irrespective of any earlier expiration of original warranty period When D Link provides replacement then the defective product becomes the property of D Link Warranty service may be obtained by contacting a D Link office within the applicable warranty period and requesting a Return Material Authorization RMA number If a Registration Card for the product in question has not been returned to D Link then a proof of purchase such as a copy of the dated purchase invoice must be provided If Purchaser s circumstances require special handling of warranty correction then at the time of requesting RMA number Purchaser may also propose special procedure as may be suitable to the case After an RMA number is issued the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit and the RMA number must be promin
35. he telephone and wall jack Microfilters that install behind the wall plate are also available A typical in line microfilter installation is shown in the diagram below Phone Jack lt Microfilter Phone Microfilter Installation Important Do not install the microfilter between the Modem and the telephone jack Microfilters are only intended for use with regular telephones Fax machines and other regular telephone devices 50 DSL 302T ADSL Modem User s Guide Line Splitter If you are instructed to use a line splitter you must install the device between the Modem and the phone jack Use standard telephone cable with standard RJ 11 connectors The splitter has three RJ 11 ports used to connect to the wall jack the Modem and if desired a telephone or telephone device The connection ports are typically labeled as follows Line This port connects to the wall jack ADSL This port connects to the Modem Phone This port connects to a telephone or other telephone device The diagram below illustrates the proper use of the splitter Phone Jack W Splitter ADSL Device Line Splitter Installation 51 D Link Offices Australia Brazil Canada Chile China Denmark Egypt Finland France Germany D Link Australia 1 Giffnock Avenue North Ryde NSW 2113 Sydney Australia TEL 61 2 8899 1800 FAX 61 2 8899 1868 TOLL FREE Australia 1800 177100 URL www dlink com
36. ic IP assignment compliant RFC 1994 Challenge Handshake Authentication Protocol compliant Supports RFC 2131 and RFC 2132 DHCP functions including automatic assignment of IP address use of subnet mask and default gateway and provision of DNS server address for all hosts RFC 2364 PPP over ATM compliant PPPoA compliant RFC 2516 PPP over Ethernet compliant PPPoE compliant RFC 2684 Bridged Routed Ethernet over ATM compliant Embedded management agent accessed via web browser Supports DHCP for up to 253 hot connections Supports ATM Forum UNI 3 1 4 0 DSL 302T ADSL Modem User s Guide Packing List Open the shipping carton and carefully remove all items In addition to this User s Guide ascertain that you have e One DSL 302T ADSL Modem e One Quick Installation Guide e One twisted pair telephone cable used for ADSL connection e One straight through Ethernet cable e One AC power adapter suitable for your electric service e An Installation CD containing this User s Manual and USB software driver Front Panel Display Place the Modem in a location that permits an easy view of the LED indicators on the front panel The LED indicators on the front panel include the Power Status ADSL Link Act Ethernet Link Act and USB Link Act indicators The ADSL Ethernet and USB indicators monitor link status and activity Link Act FEM Power Steis ADSL Eiri ren usB DSL 302T Modem Link rie Link iaict Limbii Steady green light indicates the
37. install files from your Windows 2000 installation CD or other media Follow the instructions to install the files 9 If prompted click OK to restart your computer with the new settings Configure Windows 2000 for DHCP In the Control Panel double click the Network and Dial up Connections icon 2 In Network and Dial up Connections window right click the Local Area Connection icon and then select Properties 3 Inthe Local Area Connection Properties dialog box select Internet Protocol TCP IP and then click Properties DSL 302T ADSL Modem User s Guide 4 5 In the Internet Protocol TCP IP Properties dialog box click the button labeled Obtain an IP address automatically Double click OK to confirm and save your changes and then close the Control Panel Your computer is now ready to use the Modem s DHCP server Windows ME First check for the IP protocol and if necessary install it 1 2 3 OOS est Gov En In the Windows task bar click the Start button point to Settings and then click Control Panel Double click the Network and Dial up Connections icon In the Network and Dial up Connections window right click the Network icon and then select Properties The Network Properties dialog box displays with a list of currently installed network components If the list includes Internet Protocol TCP IP then the protocol has already been enabled Skip ahead to Configure Windows ME for DHCP If I
38. ir agi F ramas 10308 Re Total Enga 3354114 CRC Emea Urnderztzed Framaz rea mutes Ga Figure 4 11 Status Network Statistics window Choose the desired interface at the top of the window and then click Refresh to view Ethernet network statistics 36 DSL 302T ADSL Modem User s Guide Connection Status D Link Eu irs Sete ka Peer Home Seit i BAC Aids D m b nitri P Adest nam du u Butnal Mass 155 T55 755 0 DHCP Seven myrnng Wan Discormeri o Tricscigitaam Te F Saale Chet Vid Bon Canesten mpm WA Weg Gpneded D HN DEEEE LEA Figure 4 12 Status Connection Status window Click Refresh to view connection status information 37 DSL 302T ADSL Modem User s Guide DHCP Clients EHCP C bis WAAC Ael rina ta IP Andres Ft Hime Lata Time 0 1010 90 61 b 1041 443 unkraram OIA pr18 1 55401 10 41 442 un brara AMC RER GU Ina 441 in krerem Malia Te bass 1h41 444 tire NO 11 VI Figure 4 13 Status DHCP Clients window This window displays the status of all current DHCP clients 38 DSL 302T ADSL Modem User s Guide Modem Status Home Setup Advanced Tools Modem Status Cannerban Ste Cennering Lipska Pate Kbps Downstream Pala Khps LA Margin DE Margin Mod ulation LOS Errom DS Line ARenuation L I Ling Aian usii Padi Mode Des Saas Maar End EA Loop Bark Count Pisar End F5 Loop Back Count Figure 4 14 S
39. k the Add button to save the address on the list of logging destinations 31 DSL 302T ADSL Modem User s Guide Update Gateway durare cun eoe a rA qn F There rramp na nes Freee iur pur ARL boden m irene unclimualty arsi paramere Te Kong 58 ever Nu SRP TE DR oe TR DOT B Kerl Re t ef Tro EE Dur Den pou une Eyaad fa fia fo Es wed click ies Lipids Colby bullas taire bo rrt a freee LG Cura Firerendd visite VLDE 15 Eu 20 121 Select a irrrerars imaqr fal tress Hoi The vyrierr allies peered ler tts G petvirrregtpIg LLE DER miiy Lien Toe need E Tape agam ee pour vEEE nid bie a Cunfiguratium He Breng Hiis Tha uywulgrr han do be mgiakd gier He Corbzrzsgonig mabre Lonfigur peer Hekup S Score DEE HR Dann Figure 4 7 Tools Update Gateway window Use the Update Gateway feature to load the latest firmware for the device You can obtain the latest version of the DSL 302T firmware by logging onto the D Link web site at www dlink com Save the latest firmware version to a file on your computer or an accessible TFTP server To upgrade firmware type in the name and path of the file in the Select a Firmware image file space or click on the Browse button to search for the file Click the Update Gateway button to begin copying the file The file will load and restart automatically Use the Configuration Backup amp Restore features to store current settings to a file on your computer or
40. l 2 Inthe Control Panel window double click on the Internet Options icon 3 Click the Connections tab and click on the LAN Settings button 4 Verify that the Use proxy server option is NOT checked If it is checked click in the checked box to deselect the option and click OK Alternatively you can access this same menu using the Tools pull down menu in Internet Explorer If this is the first time you are accessing the configuration manager and you simply want to establish a connection to the Internet you may want to read the section titled Configure the Modem in the previous chapter 25 DSL 302T ADSL Modem User s Guide DHCP Configuration Use the DHCP Configuration window to configure the Modem to act as a DHCP server for the LAN D Link In E DHL Cornfegir ga The desig can be setip z a DHCP Sonar ro distribesno E siliran na the LAH se het pallies ll Drei E e 16311 Erdir 182 168 1253 Lease Te ED Serna COE HI je Figure 4 1 Setup DHCP Configuration window Configure LAN DHCP services by defining the following parameters Start IP Type in the base address for the IP pool of unassigned IP addresses End IP Type in the last address of the contiguous IP address range to be used by the Modem for DHCP function Lease Time This specifies the amount of time in seconds a client can lease an IP address from the dynamically allocated IP pool 26
41. make sure which encapsulation is being supported 8 For most users the remaining settings will not need to be changed See your ISP for further information 9 Click the Apply button when you have entered all the information The browser window may briefly go blank After a few seconds the new connection you just configured will become the active connection for the Modem 10 To make your temporarily saved connection permanent click the Save All button in the System Commands window on the Tools tab Bridge Make sure you have selected Bridge from the Type pull down menu so that you are now configuring setting in the menu titled Bridged Connection Setup Follow the instructions below to set up the connection el Warn cona 1 PPP B 15 Tyra eem Ka Bilige Sening PVC Spam canbe FL Ve V hb wer Ds DE LEES e PCR bpi sa bpr 2 2 Apphy Cancel D On Figure 3 6 Setup New Connection Bridge window To configure the WAN connection for Bridge perform the steps listed below Some of the settings do not need to be changed when you first set up the device but can be changed later if you choose Bridge means a pure bridged connection with no IP address assigned to the Modem This connection method makes the Modem act as a bridge and just passes packets across the DSL port 1 Type ina Name in the space provided if you wish or leave the default name 2 Make sure Bridge appears listed a
42. name needed access the Modem s Record info here management interface When you attempt to connect to the device through a web browser you will be prompted to enter this Username The default Username for the Modem is admin This may be changed by the user This is the Password you will be prompted to enter Password when you access the Modem s management interface The default Password is admin This may be changed by the user This is the IP address you will enter into the Address field of your web browser to access the Modem s configuration graphical user interface GUI using a web browser The default IP address is 192 168 1 1 and it is referred to as the Management IP address in this User s Manual This may be changed to suit any IP address scheme the user desires This address will be the base IP address used for DHCP service on the LAN when DHCP is enabled This is the subnet mask used by the DSL 302T and will be used throughout your LAN The default subnet mask is 255 255 255 0 This can be changed later LAN IP addresses for the DSL 302T LAN Subnet Mask for the DSL 302T viii DSL 302T DSL Modem User s Guide Information you will need about your Ethernet LAN or computer If your computer has an Ethernet NIC you can Record info here connect the DSL 302T to this Ethernet port using an Ethernet NIC Ethernet cable You can also use the Ethernet port on the DSL 302T to connect to other Ethernet devices such as a Wi
43. net port on a PC or notebook computer p 10 100 BASE TX Cable using the Ethernet straight through wires cable provided as shown in this diagram 10 100 BASE TX straight through DSL 302T ADSL Modem User s Guide Hub or Switch to Modem Connection Connect the Modem to an uplink port MDI II on an Ethernet hub or switch with a straight through cable as shown in the diagram below 10M Switch Hub If you wish to reserve the uplink port on the switch or hub for another device connect to any on the other MDI X ports 1x 2x etc with a crossed cable 10 100 BASE TX Cable straight through wires straight through DSL 302T ADSL Modem User s Guide Configuring the Modem for the First Time The first time you setup the Modem configure the WAN connection using a single computer connected directly to the Modem Once the WAN connection is functioning properly you may continue to make changes to Modem configuration including IP settings and DHCP setup This chapter is concerned with using your computer to configure the WAN connection The following chapter describes the various menus used to configure and monitor the Modem including how to change IP settings and DHCP server setup Wan Configuration Summary 1 Connect to the Modem To configure the WAN connection used by the Modem it is first necessary to communicate with the Modem through its management interface which is HTML based and can be accesse
44. nternet Protocol TCP IP does not display as an installed component click Add In the Select Network Component Type dialog box select Protocol and then click Add Select Microsoft in the Manufacturers box Select Internet Protocol TCP IP in the Network Protocols list and then click OK You may be prompted to install files from your Windows Me installation CD or other media Follow the instructions to install the files 10 If prompted click OK to restart your computer with the new settings Configure Windows ME for DHCP 3 4 5 In the Control Panel double click the Network and Dial up Connections icon In the Network and Dial up Connections window right click the Network icon and then select Properties In the Network Properties dialog box select TCP IP and then click Properties In the TCP IP Settings dialog box click the Obtain and IP address automatically option Double click OK twice to confirm and save your changes and then close the Control Panel Your computer is now ready to use the Modem s DHCP server Windows 95 and Windows 98 First check for the IP protocol and if necessary install it 1 In the Windows task bar click the Start button point to Settings and then click Control Panel Double click the Network icon The Network dialog box displays with a list of currently installed network components If the list includes TCP IP and then the protocol has already been enabled skip to Configure
45. nterpretation of bits in the IP address The bits of the subnet mask correspond directly to the bits of the IP address Any bit an a subnet mask that is to correspond to a net ID bit in the IP address must be set to 1 49 DSL 302T ADSL Modem User s Guide Microfilters and Splitters Most ADSL clients will be required to install a simple device that prevents the ADSL line from interfering with regular telephone services These devices are commonly referred to as microfilters or sometimes called inaccurately line splitters They are easy to install and use standard telephone connectors and cable Some ADSL service providers will send a telecommunications technician to modify the telephone line usually at the point where the telephone line enters the building If a technician has divided or split your telephone line into two separate lines one for regular telephone service and the other for ADSL then you do not need to use any type of filter device Follow the instructions given to you by your ADSL service provider about where and how you should connect the Modem to the ADSL line Microfilters Unless you are instructed to use a line splitter see below it will be necessary to install a microfilter low pass filter device for each telephone or telephone device answering machines Faxes etc that share the line with the ADSL service Microfilters are easy to install in line devices which attach to the telephone cable between t
46. nts of your ADSL account vii DSL 302T DSL Modem User s Guide Information Required for Installation Information you will need from your ADSL service provider This is the Username used to log on to your ADSL Record info here service provider s network It is commonly in the form user isp com Your ADSL service provider uses this to identify your account This is the Password used in conjunction with the Password Username above to log on to your ADSL service providers network This is used to verify the identity of your account This is the method your ADSL service provider uses to send and receive data between the Internet and your Connection Protocol computer Your Modem supports the following connection protocols PPPoE PPPoA CLIP IPoA and Bridge This is the method your ADSL service provider will use to verify your Username and Password when you log on to their network Your Modem supports the PAP and CHAP protocols Security Protocol This is the Virtual Path Identifier VPI It is used in conjunction with the Virtual Channel Identifier VCI below to identify the data path between your ADSL service provider s network and your computer This is the Virtual Channel Identifier VCI It is used in conjunction with the VPI above to identify the data path between your ADSL service provider s network and your computer Information you will need to change settings on the DSL 302T Modem This is the User
47. o have access to other web servers Valid IP addresses range from 0 0 0 0 to 255 255 255 255 D Link LE uso i Home E bit Cumpnscfmmn Site gt ame corn 1 PPP Y Tyra Sme sl Salir Settee MAC Settings Er apauiakre Fier ee as Mask tod uen Depu Gateway Fi KZ emm E D ET e pais 3 cei 3 Apply Cancel SINE IP Beltre as Bana wi P ez bp zl bes Figure 3 7 Setup Static IP To configure the WAN connection for Static perform the steps listed below Some of the settings do not need to be changed the first time the device is set up but can be changed later if you choose 23 DSL 302T ADSL Modem User s Guide 10 11 Click the Connection 1 button under WAN Setup to view the default PPPoA Connection Setup configuration menu Select Static from the Type pull down menu This action will change the menu so it offers different settings for configuration Type in a Name in the space provided If you are told to change the VPI or VCI values type in the values given to you by your service provider Many users will be able to use the default settings Leave the default QoS values if you are unsure or the ISP did not provide this information Do not change the PCR or SCR values unless you are required to do so If you are told to change these type in the values given to you by your service provider The Encapsulation values LLC SNAP and VC MUX are two di
48. ols window Then click on User Management to bring up the following window 28 DSL 302T ADSL Modem User s Guide User Management Use this menu to change the user name and password used to gain management access to the Modem St mw a Unger Baa gered ta asi ki ge your Leg berg Pare Lipe piura mn Ferraj ES Lain Parse id z E tie Tireni D rm SS Q Figure 4 4 Tools User Management window Type the current User Name in the entry field provided Type in the new Password in the entry field provided Type in the new password again in the Confirm Password field If desired change the Idle Timeout value Click Apply 29 DSL 302T ADSL Modem User s Guide System Commands These menu options are used to save setting restart reboot the Modem or reset the configuration to the factory settings Home setup Satus Hel B edie Ormani Serle Comrade alie veu fo cm cut bad ic seem action Press B aun o eec ute 5 Corea rad Fans ep bulas is ede l peer Gris da Dr Egirand Cone pure DI Fia yg kwriy II yi ii a a Vu ee seria ed patur ee con na Chala sel MATT Dick E Fo gp Ley Steel inni gag oho uli lona Fes GLEHN 00 sa a i t mia n P anu nee nor Eae Your corr ursi ones Ere D aen will emend bach ja fes presi si paene buten pps re Hiin ARTE Casnecban to the unii uti bs las ng rari reparei eter He ont renariu Unam pir Geen toe ios iarirr
49. ort or an available USB port the quickest and easiest way to set up the DSL 302T is to insert the Installation CD into the CD ROM drive of your computer and follow the instructions provided in the Quick Installation Guide Alternatively you can click the Install DSL 302T link on the initial pop up menu that appears shortly after inserting the CD and follow the instructions as they are presented If the menu fails to appear explore the CD and find the file dsl302t exe and double click it to launch the installation software Before You Start Please read and make sure you understand all the prerequisites for proper installation of your new Modem Have all the necessary information and equipment on hand before beginning the installation Installation Overview The procedure to install the Modem can be described in general terms in the following steps 1 Gather information and equipment needed to install the device Before you power on the device or connect it to your computer make sure you have all the necessary information cables power adapter and any other required equipment listed 2 Install the hardware that is connect the cables Ethernet and telephone to the device and connect the power adapter 3 Check the IP settings on your computer and change them if necessary so the computer can access the web based software built into the Modem 4 Use the web based management software to configure the device to suit the requireme
50. ows choose the option Obtain an IP address automatically in the TCP IP network component described above When the computers are restarted their IP settings will automatically be assigned by the Modem The Modem is set by default to use DHCP See the discussion in Chapter 5 for information on how to use configure the Modem for DHCP Changing the IP Address of the Modem When planning your LAN IP address setup you may use any scheme allowed by rules that govern IP assignment It may be more convenient or easier to remember an IP scheme that use a different address for the Modem Or you may be installing the Modem on a network that has already established the IP settings Changing the IP address is a simple matter and can be done using the web manager If you are incorporating the Modem into a LAN with an existing IP structure be sure to disable the DHCP function Also consider the effects of the NAT function which is enable by default An IP addressing scheme commonly used for Ethernet LANs establishes 10 0 0 1 as the base address for the network Using Example 2 below the Modem is assigned the base address 10 0 0 1 and the remaining addresses are assigned manually or using DHCP Alternative IP Assignment Computer 1 10 0 0 2 255 255 255 0 10 0 0 1 Computer 2 10 0 0 3 255 255 255 0 10 0 0 1 Computer 3 10 0 0 4 255 255 255 0 10 0 0 1 IP Setup Example 2 These two examples are only examples you can use to help you get started
51. r Thranesgate 77 0175 Oslo Norway TEL 47 22 99 18 90 FAX 47 22 20 70 39 SUPPORT 800 10 610 URL www dlink no D Link Russia Michurinski Prospekt 49 117607 Moscow Russia TEL 7 095 737 3389 amp 7 095 737 3492 FAX 7 095 737 3390 URL www dlink ru E MAIL vl dlink ru D Link International 1 International Business Park 03 12 The Synergy Singapore 609917 TEL 6 6774 6233 FAX 6 6774 6322 E MAIL info dlink com sg URL www dlink intl com D Link South Africa Unit 2 Parkside 86 Oak Avenue Highveld Technopark Centurion Gauteng South Africa TEL 27 12 665 2165 FAX 27 12 665 2186 URL www d link co za E MAIL attie d link co za D Link Iberia Spain and Portugal Sabino de Arana 56 bajos 08028 Barcelona Spain TEL 34 93 409 0770 FAX 34 93 491 0795 URL www dlink es E MAIL info dlink es D Link Sweden P O Box 15036 S 167 15 Bromma Sweden TEL 46 8 564 61900 FAX 46 8 564 61901 URL www dlink se E MAIL info dlink se D Link Taiwan 2F No 119 Pao chung Road Hsin tien Taipei Taiwan TEL 886 2 2910 2626 FAX 886 2 2910 1515 URL www dlinktw com tw E MAIL dssqa tsc dlinktw com tw D Link Middle East Deniz Bilgisayar Buyukdere Cad Naci Kasim Sk No 5 Mecidiyekoy Istanbul Turkey TEL 90 212 213 3400 FAX 90 212 213 3420 E MAIL smorovati dlink me com D Link Middle East CHS Aptec Dubai P O Box 33550 Dubai United Arab Emirates TEL 971 4 366 885 FAX 971 4 355 941 U K U S A E
52. r the LAN Local Area Network and for the WAN Wide Area Network setup The first menu you see when clicking the Setup tab is the DSL Setup menu AII the information you need to make the changes needed for a functioning WAN connection should have been provided to you by your ISP or network service provider One of the settings you may be asked to change is the Modulation type used for the ADSL connection The DSL Setup menu is used to change the type of modulation used for the WAN connection Tools status Hel Ir curb ipa Ire niue Tee r TH r GET OLTE fv WGL o o Apply Conch DER BE Figure 3 3 Modem Setup menu If you know what Modulation type is used for your service select the desired modulation type and then click Apply The modulation types available are T1413 G DMT GLITE and MMODE By default the Modem uses MMODE Now you are ready to configure the remaining settings needed for the WAN connection Click the Connection button to configure the other WAN settings DSL 302T ADSL Modem User s Guide Configure a New Connection The default connection protocol used for the Modem is Point to Point Protocol over ATM PPPoA The menu used to configure ADSL service using this protocol is the menu you see when clicking on the Connection button under WAN Setup on the left side of the window If you are using either PPPoE or a Bridge connection it will be necessary to change the Type using the pull down
53. reless Access Point If your computer has an available USB port you can USB port connect the DSL 302T to this USB port using a USB cable Your DSL 302T ADSL Modem is configured by default to be a DHCP server This means that it can assign an IP address subnet mask and a default gateway address to computers on your LAN The DHCP Client status default range of IP addresses the DSL 302T will assign are from 192 168 1 2 to 192 168 1 254 Your computer or computers needs to be configured to Obtain an IP address automatically that is they need to be configured as DHCP clients It is recommended that your collect and record this information here or in some other secure place in case you have to re configure your ADSL connection in the future Once you have the above information you are ready to setup and configure your DSL 302T ADSL Modem mere The Modem may be reset to its factory default settings by performing a Restore A settings operation within the management interface see System Commands Note below If you cannot gain access to the management interface you may opt to use the Reset button on the rear panel of the device see Factory Reset Button below DSL 302T DSL Modem User s Guide Installing the USB Driver The CD ROM shipped with the Modem contains the USB driver software 1 Insert the DSL 302T Installation CD ROM into the CD ROM drive 2 Connect the USB cable to the device Within a few seconds you should
54. s a filtering mechanism may be necessary to avoid mutual interference A low pass filter device can be installed for each telephone that shares the line with the ADSL line These filters are easy to install passive devices that connect to the ADSL device and or telephone using standard telephone cable Ask your service provider for more information about the use of low pass filters with your installation Operating Systems The DSL 302T uses an HTML based web interface for setup and management The web configuration manager may be accessed using any operating system capable of running web browser software including Windows 98 SE Windows ME Windows 2000 and Windows XP DSL 302T ADSL Modem User s Guide Web Browser Any common web browser can be used to configure the Modem using the web configuration management software The program is designed to work best with more recently released browsers such as Opera Microsoft Internet Explorer version 5 0 Netscape Navigator version 4 7 or later versions The web browser must have JavaScript enabled JavaScript is enabled by default on many browsers Make sure JavaScript has not been disabled by other software such as virus protection or web user security packages that may be running on your computer Ethernet Port NIC Adapter Any computer that uses the Modem must be able to connect to it through the Ethernet port on the Modem This connection is an Ethernet connection and therefore req
55. s the Type of connection protocol used 22 DSL 302T ADSL Modem User s Guide 3 Do not change the VPI or VCI values unless you are required to do so If these settings are incorrect the ADSL connection will not function Many users will be able to use the default settings If you are told to change these type in the values given to you by your service provider 4 Leave the default QoS values if you are unsure or the ISP did not provide this information 5 Do not change the PCR or SCR values unless you are required to do so If you are told to change these type in the values given to you by your service provider 6 The Encapsulation values LLC SNAP and VC MUX are two different methods of encapsulating the PPP packet Contact your ISP to make sure which encapsulation is being supported 7 Click the Apply button when you have entered all the information The browser window may briefly go blank After a few seconds the new connection you just configured will become the active connection for the Modem 8 To make your temporarily saved connection permanent click the Save All button in the System Commands window on the Tools tab Static IP Static is used whenever a known static IP is assigned The accompanying information such as the Subnet mask and the gateway should also be specified in order to be able to connect Up to three Domain Name Server DNS addresses can also be specified These are the servers would enable you t
56. s the magnetic media on which D Link provides its software product against failure during the same warranty period This warranty applies to purchased software and to replacement software provided by D Link pursuant to this warranty but shall not apply to any update or replacement which may be provided for download via the Internet or to any update which may otherwise be provided free of charge D Link s sole obligation under this software warranty shall be to replace any defective software product with product which substantially conforms to D Link s applicable product documentation Purchaser assumes responsibility for the selection of appropriate application and system platform software and associated reference materials D Link makes no warranty that its software products will work in combination with any hardware or any application or system platform software product provided by any third party excepting only such products as are expressly represented in D Link s applicable product documentation as being compatible D Link s obligation under this warranty shall be a reasonable effort to provide compatibility but D Link shall have no obligation to provide compatibility when there is fault in the third party hardware or software D Link makes no warranty that operation of its software products will be uninterrupted or absolutely error free and no warranty that all defects in the software product within or without the scope of D Link s applicable prod
57. stalled If you are using Windows XP the TCP IP is enabled by default for standard installations Below is an illustrated example of how to configure a Windows XP system to automatically obtain IP settings from the Modem Following this example is a step by step description of the procedures used on the other Windows operating systems to first check if the TCP IP protocol has been installed if it is not instructions are provided for installing it Once the protocol has been installed you can configure the system to receive IP settings from the Modem For computers running non Windows operating systems follow the instructions for your OS that configure the system to receive an IP address from the Modem that is configure the system to be a DHCP client sever If you are using this Modem to provide Internet access for more than one A computer you can use these instructions later to change the IP settings for the other computers However you cannot use the same IP address since every Note computer must have its own IP address that is unique on the local network DSL 302T ADSL Modem User s Guide Configure Windows XP for DHCP Use the following steps to configure a computer running Windows XP to be a DHCP client 1 From the Start menu on your desktop go to Settings then click on Network Connections D Uu Creo and aum SA Heg ai apt Tahta sei Sei Herm CT m Long Agence L In CH T md es a m Windows XP f 2
58. stalling the device some settings may need to be changed before the Modem can establish a connection Factory Reset Button The Modem may be reset to the original factory default settings by depressing the reset button for a few seconds while the device is powered on Use a ballpoint or paperclip to gently push down the reset button Remember that this will wipe out any settings stored in flash memory including user account information and LAN IP settings The factory default IP address of the Modem is 192 168 1 1 and the subnet mask is 255 255 255 0 the default management Username is admin and the default Password is admin DSL 302T ADSL Modem User s Guide Network Connections Network connections are provided through the ADSL port the Ethernet port and the USB port on the back of the Modem See the Rear Panel diagram above and the illustrations below for examples See Installing the USB Driver above for a description of the USB driver installation procedure Connect ADSL Line Use the ADSL cable included with the Modem to connect it to a telephone wall socket or receptacle Plug one end of the cable into the ADSL port RJ 11 receptacle on the rear panel of the Modem and insert the other end into the RJ 11 wall socket If you are using a low pass filter device follow the instructions included with the device or given to you by your service provider The ADSL connection represents the WAN interface the connection to the Internet It is
59. tatus Modem Status window This window displays the status of the modem as well as DSL statistics 39 DSL 302T ADSL Modem User s Guide Product Info D Link tL DLE Setup Model Mumbar DL 2026 HN Fais lani Usage Spa Number nant LES ADO Du pa LES VE Dno here MAC Dx Dd D8 30 03107 D s WC HA LES MAL H LES Host Wat LA Sofware Versions IET WRIT AE 0p401r5 ATM Oriar 0205 nc DES HAL 30002 Dn Lr Datume 1 01 00 00 enge A AAF HAL 0 06 06 8 POP Firwat Dap Boot Lowder n2zni Figure 4 15 Status Product Info window This window displays product information including software versions 40 DSL 302T ADSL Modem User s Guide System Log Home Setup Tools eS oni purab on Tree Final HAT marara hired LEB intrare r being brirsghi op Bridge Creer bes LEB interface Succes efit Brought Lip Desh Cars H dram Figure 4 16 Status System Log window Click Refresh to get the most current system log information 41 DSL 302T ADSL Modem User s Guide Help Usern The ageres ir te DSL gr ronn Pawee The pas gerre rer fs Clg Cn Demaegd nakls pr Pern and rea Ta timc Wadi eres ray arts te Eulailad Ss rho breed i hepp a We reg Gpecitesc mar OGL ar disposer ize ans das ng wii dir ker kad pr mstonds A naa qem REF Keep Ai Shen ai dimen Oph ie ibl rsabda Tas ed ce purina he ires kon tt Dau ion esce lo your d erri Delora kerana ege
60. the physical link to the service provider s network backbone and ultimately to the Internet Connect Modem to Ethernet The Modem may be connected to a single computer or Ethernet device through the 1OBASE TX Ethernet port on the rear panel Any connection to an Ethernet concentrating device such as a switch or hub must operate at a speed of 10 100 Mbps only When connecting the Modem to any Ethernet device that is capable of operating at speeds higher than 10Mbps be sure that the device has auto negotiation NWay enabled for the connecting port In order to connect the Modem to an Ethernet LAN it is necessary to install Note 3 2 party PPP connection software on any system used to access the Internet Use standard twisted pair cable with RJ 45 connectors The RJ 45 port on the Modem is a crossed port MDI X Follow standard Ethernet guidelines when deciding what type of cable to use to make this connection When connecting the Modem directly to a PC or server use a normal straight through cable You should use a crossed cable when connecting the Modem to a normal MDI X port on a switch or hub Use a normal straight through cable when connecting it to an uplink MDI ID port on a hub or switch The rules governing Ethernet cable lengths apply to the LAN to Modem connection Be sure that the cable connecting the LAN to the Modem does not exceed 100 meters Computer to Modem Connection Connect the Modem directly to a 10 100BASE TX Ether
61. tivity of the ADSL connection via the ATM network This is similar to a Ping test except it is testing the ATM network instead of the IP network D Link Bue tera fe Dese Home Setup Advanced OAM Tesi Cormaction VFI Wo Cc conn 1 PPPoA H 35 B EI DAN Test Result Mo test is running Figure 4 9 Tools OAM Test window To test your modem select a Connection choose a Test Type and click Test 34 DSL 302T ADSL Modem User s Guide Status The Status section abrea you da iw ip Einius Epsdirios ar derent connectiang aed interfaces heneprk Sinia Waw he Graiis of differen mierfaces Elhamel Led CSL Cnnnacilom Stites Wiee De Rate of gfepnlcoreeriora Pb enis Wew s Lir of DISC IP riena Moilem States Waw he Status Blabziirs of beradeard LE roana Visus bolo zmntlnr View the Product marmmaltien ans Sotas Versions Synem L aq Www ha Log massages Ai it A Figure 4 10 Opening Status window Click the hyperlink for the desired Status window 35 DSL 302T ADSL Modem User s Guide Network Statistics D Link K r Rarecgkt jee Props E Chuwa B an inierace to vies qur network sanus Ethemet UBB TC Ce Ed Eg Good Tx Frames kd onem le n Good Tz Br sir ai Frames H pad Te Moll ast Frames Tx Total Eyiti 1119118 EmarFrames End Gamer Senes Eres 0 raras Gpad Fx Frames K Good Fx Broadcast Frames ir Ged Te Wof
62. u by your service provider Leave the default QoS values if you are unsure or the ISP did not provide this information Do not change the PCR or SCR values unless you are required to do so If you are told to change these type in the values given to you by your service provider Supply a Username and Password used to verify the identity of your account These are usually provided by your ISP The Encapsulation values LLC SNAP and VC MUX are two different methods of encapsulating the PPP packet Contact your ISP to make sure which encapsulation is being supported For most users the remaining settings will not need to be changed See your ISP for further information Click the Apply button when you have entered all the information The browser window may briefly go blank After a few seconds the new connection you just configured will become the active connection for the Modem To make your temporarily saved connection permanent click the Save All button in the System Commands window on the Tools tab 20 DSL 302T ADSL Modem User s Guide PPPoE The required information used to setup a PPPoE connection is identical to that needed for a PPPoA connection Make sure you have selected PPPoE from the Type pull down menu so that you are now configuring setting in the menu titled PPPoE Connection Setup Follow the instructions below to set up the connection D Link ike Cid a pm Mosi PPPOE Connection S
63. uct documentation will be corrected iii TABLE OF CONTENTS About This User s Guides svi en aie pe E e e e p ee d e RD Ree eo e ERR bates vil Before Y ou Start ea Re ae Re Ep t re Ee naa pened et vii Information Required for Installation n sns asnasan viii Installing the USB DIrwver s unas a aha Od e eo iro ite red e pe rite x INTRODUCTION Peer 1 Modem Description and Operation ener enne nne nennen ete tnsn nete trennen nee ene 1 Modem Features teer rU E PR SEENEN EES 3 Standards Compatibility and Compliance eese eene nennen tnnt e nenne entente 4 Front Panel Display sci o e p ne i ee e f eR e ER denis Re e Pe Up RE Ee edades 5 Rear Panel Connections a ob n ee Sp RO Ree NAE u 6 HARDWARE INSTALLATION III IIIa aano nc cu echa aan aa nunca 7 Power on Modem iere o Rae edel 7 Pactory Reset BUtton eee eco edere eret e ei n S noeh NER REPE ee cree din 7 Network Connections ees ee ideni med bete eed iie 8 CONFIGURING THE MODEM FOR THE FIRST TIME eese 10 Configuring IP Settings on Your Computer 10 Access the Configuration Manager u u u u u u 15 Home 16 Configure the Modem vs eod Avi tev it eem tie tpe diede ar et dd eg d apap 17 I II 18 Configure a New Connection oci a RU OPERE Basie ence DER BR SER 19 W
64. uires that your computer be equipped with an Ethernet port as well Most notebook computers are now sold with an Ethernet port already installed Likewise most fully assembled desktop computers come with an Ethernet NIC adapter as standard equipment If your computer does not have an Ethernet port you must install an Ethernet NIC adapter before you can use the Modem If you must install an adapter follow the installation instructions that come with the Ethernet NIC adapter Additional Software It may be necessary to install software on your computer that enables the computer to access the Internet Additional software must be installed if you are using the device a simple bridge For a bridged connection the information needed to make and maintain the Internet connection is stored on another computer or gateway device not in the Modem itself If your ADSL service is delivered through a PPPoE PPPoA or IPoA connection the information needed to establish and maintain the Internet connection can be stored in the Modem In this case it is not necessary to install software on your computer It may however be necessary to change some settings in the device including account information used to identify and verify the connection All connections to the Internet require a unique global IP address For bridged connections the global IP settings must reside in a TCP IP enabled device on the LAN side of the bridge such as a PC a server a gateway device
65. unit is powered on When the device is powered off this remains dark Lights steady green during power on self test POST Once the connection status has been settled the light will blink green If indicator lights steady green after the POST the system has failed and the device should be rebooted Steady green light indicates a valid ADSL connection This will light after the ADSL Link Act ADSL negotiation process has been settled A blinking green light indicates activity on the WAN ADSL interface mu A solid green light indicates a valid link on startup This light will blink when Eten e ETL ge there is activity currently passing through the Ethernet port Steady green light indicates a valid USB connection A blinking green light USB Link Act indicates activity on the USB interface DSL 302T ADSL Modem User s Guide Rear Panel Connections All cable connections to the Modem are made at the rear panel Connect the power adapter here to power on the Modem Use the Reset button to restore the settings to the factory default values see Factory Reset Button in the next chapter for instructions on using the reset button USB port connect USB cable here and install the USB driver Factory Reset Ethernet button port connect Ethernet cable here Power cord connects ADSL port connect ADSL cable here The Modem may be rebooted by disconnecting and then reconnecting the power
66. ur organization use LID Link LANsmart ONovell NetWare LINetWare Lite ASCO Unix Xenix OPC NFS 03Com 3 Open OBanyan Vines LIDECnet Pathwork LIWindows NT OWindows NTAS LIWindows op OOthers 5 What network management program does your organization use LID View OHP OpenView Windows OHP OpenView Unix LISunNet Manager LINovell NMS LINetView 6000 LIOthers 6 What network medium media does your organization use LIFiber optics LIThick coax Ethernet OThin coax Ethernet 010BASE T UTP STP L1100BASE TX L1100BASE T4 L1100VGAnyLAN LIOthers 7 What applications are used on your network LIDesktop publishing LISpreadsheet LIWord processing LICAD CAM LIDatabase management LlAccounting LlOthers 8 What category best describes your company LlAerospace LIEngineering OEducation OFinance OHospital OLegal Olnsurance Real Estate Manufacturing LIRetail Chainstore Wholesale LIGovernment LITransportation Utilities Communication OVAR LISystem house company OOther 9 Would you recommend your D Link product to a friend OYes ONo ODon t know yet 10 Your comments on this product
67. use a proxy server in the Internet settings In Windows Internet Explorer you can check if a proxy server is enabled using the following procedure 1 In Windows click on the Start button go to Settings and choose Control Panel 2 In the Control Panel window double click on the Internet Options icon 3 Click the Connections tab and click on the LAN Settings button 4 Verify that the Use proxy server option is NOT checked If it is checked click in the checked box to deselect the option and click OK Alternatively you can access this Internet Options menu using the Tools pull down menu in Internet Explorer DSL 302T ADSL Modem User s Guide To use the web based management software launch a suitable web browser and direct it to the IP address of the Modem Type in http followed by the default IP address 192 168 1 1 in the address bar of the browser The URL in the address bar should read http 192 168 1 1 Home D Link Bairy fete Sor Peon Tools Status Hel Login Pinasa log in d continua Login Nama admin Passwon Figure 3 1 Home Login window A new window will appear and you will be prompted for a user name and password to access the web based manager Use the default user name admin and password admin for first time setup You should change the web based manager access user name and password once you have verified that a connection can be established The user name and password allows
68. y Zeie rrr enrsm NOTE Comsrisihy In the arit ss ll be bel You can cena Tm fe uri ioa Figure 4 5 Tools System Commands window Save All In order to save the configuration changes you have just made they must be saved to the Modem s non volatile RAM by clicking on the Save All button Restart Click the Restart button to restart the Modem If you have not saved your changes the Modem will revert to the previously saved configuration upon rebooting the Modem Restore The DSL 302T can be reset to the default configuration for all settings using the Restore option This will also change the both the LAN and WAN IP address of the device so these will need to be reconfigured accordingly To perform a factory reset click the Restore button Since the IP settings will return to their default you will lose access to the Web Manager To use the Web Manager interface the LAN IP address will need to be reconfigured 30 DSL 302T ADSL Modem User s Guide Remote Log Use this menu to designate receiver stations for event messages form the Modem n ID D sl fabri ora u rinusbur lions opty Cancel PEELE DA Figure 4 6 Tools Remote Log window To set up a destination for event messages 1 Selectthe Log Level form the pull down list 2 Add and IP address of a server or station used to log event messages sent from the Modem 3 Type an IP address in the Add an IP Address field and clic

DSL-302T ADSL Modem User`s Manual - D-Link

Contents

Download Pdf Manuals

Related Search

Related Contents