SeeTool - Solutions for KNX
Contents
1. single room Technical specifications User manual Quick guid This room is equipped with a move ment dependent automatic light control with light regulation and manual control temperature control Automatic mode operation invisible buttons Temperature control heating cooling Movement detection will automatically set the temperature control into comfort mode To save energy this will not happen until a person has been in the room for more than 3 minutes In this way the temperature control is not affected if someone is present in the room just for a short period of time If no movement is detected within a delay time of 25 minutes the temperature control is set into standby mode Comfort mode default room temperature set point heating 21 C cooling 24 C Standby mode default room temperature set point heating 19 C cooling 26 C Frost Heat protection heating 7 C cooling 35 C The set point can be adjusted by the user 3 C from given set point This is done by pushing invisible buttons on both sides of the display frame If a window contact breaking contact is connected to the EMO valve drive the temperature control will be set into frost heat protection se rvice mode when the window is open Schneider foryour 06 10 Application 8 3 0 0 0 4 amp Electric custom er ISC02083_EN 132. 60 Factor 0 2047 1562 Block configuration Push button 2 Move presence block 1 disable Select push button Move presence block 2 enable function Edges with 2 byte Light control enable values Block 2 general gt Movement sensors Push button 2 edges values Sector orientated settings enable Value 1 basis factor 300 Dead time beginning of movement enable Basis possible Time base 1 min values in brackets 0 16 0 to 327 52 Time factor 3 Factor 0 2047 1875 Block 2 general gt Brightness Push button 3 Movement detection is brightness Select push button independ function Edges with 2 byte Block 2 general gt Time values Time base for staircase timer 1 min Time factor for staircase timer 25 Application 8 3 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control heating and cooling with KNX EMO valve drive single room Technical specifications Configuration KNX Argus presence with light control KNX Push button 2 gang with RTC General light control Push button 3 edges values Automatic at object value 0 Value 1 basis factor 100 Memory behaviour parameterised Basis possible setpoint value values in brackets 0 08 0 to 163 76 Extended controller Factor 0 2047 1250 parameters enable Push button 4 General light control gt Select push button Control response in automatic mode gt function Switchi
3. C Room temperature controller Default setpoints for heating and cooling depends on presence in a room Parameter page Parameter Value Control general gt Setpoints Heating setpoint for comfort 5 40 C 21 C Control general gt Setpoints Heating setpoint for standby 5 40 C 19 C Control general gt Setpoints Control general gt Setpoints Cooling setpoint for comfort Cooling setpoint for standby 5 40 C 24 C 5 40 C 26 C The user is allowed to adjust the default setpoint within specified limits Parameter page Parameter Value Control general Max upper setpoint adjustment 0 10 K 3 K Control general Max lower setpoint adjustment 0 10 K 3 K fine tuning 10 Application 8 3 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control heating and cooling with KNX EMO valve drive single room Technical specifications Fine tuning Value correction of measured temperature The temperature in the room is measured by the internal temperature sensor in the room temperature controller The actual temperature is shown in the display If the value is not representative for the room it is possible to adjust it by parameter Actual temperature measured temperature adjustment value heating Control general gt Control heating Reset time for heating in min Parameter
4. Status switch active status resp object Proportional range for Status value object active status resp object cooling in 0 1 K 10 255 40 Reset time for cooling 1 255 min 20 1 Dimming time reduction Set 0 dimming time reduction for value telegram at 6 KNX EMO valve drive with 2 binary inputs heating 2 1 1 gt 0 Control value Input 1 byte 2 1 4 lt 7 Binary input 1 Switch 1 bit Input 1 Function switch toggle Command on rising edge off Command on falling edge on KNX EMO valve drive with 2 binary inputs cooling 2 1 2 gt 0 Control value Input 1 byte Application 8 3 0 0 0 4 ly Movement dependent automatic light control with light regulation and manual control temperature control heating and cooling with KNX EMO valve drive single room Technical specifications Group addresses Address Name proposal Function WANA Room 001 Light On Off Light on off by the light controller 1 1 2 Room 001 Light Dimming Light dimming up down by the light controller 1 1 3 Room 001 Light Value Light absolute value by the light controller q 1 4 Room 001 Light Status switch Feedback from actuator On Off settings 1 1 5 Room 001 Light Status value Feedback from actuator 0 100 1 1 6 Room 001 Light Resulting actual value Measured lux value by light controller corrected value 1 1 7 Room 001 Light Lux value setting Different lux values from
5. level setpoint in reference area Parameter page Parameter Value General light control gt l Control response in auto mode gt Brightness Nominal value reference surface 10 2000 lux 500 lux General light control gt l Control response in auto mode gt Brightness Hysteresis 10 50 20 The actual brightness value corrected measured value can be sent cyclically to the bus via communication object 107 This can be used for test purpose together with ETS If it is used for other purposes the value should not be sent too often for bus load reasons If there is no receiver to display the value in the project the function should be disabled after the test phase Parameter page Parameter Value General Send actual value cyclically reference enable disable disable surface General Time base send lux value 1s 1 min 1 h 1 min General Time factor send lux value 1 255 30 Cycle time Time base x Time factor my fine tuning Application 8 3 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control heating and cooling with KNX EMO valve drive single room Technical specifications Fine tuning The delay time for changing between standby comfort is dependent on presence activity in a room To save energy the switch over from standby to comfort is done when movement is detected after a specified
6. offers sophisticated control of the lighting heating and cooling with an automatic movement detector and additional manual control plus an open window sensing function to set temperature at comfort and standby mode gt Energy savings gt Flexibility Temperature Combining the presence and daylight For optimized costs the device s functional function with temperature control to the interaction is predefined Functionality can room application we are able to utilize the be modified or changed at any time in the daylight and temperature factors to optimize lifecycle and allows a maximum of flexibility and save energy during the active period of and adaptation when walls are removed and use throughout the year Presence depen rooms combined dant lighting control plus daylight harvesting can achieve a 65 electricity saving compared to installations without automatic function At temperature side presence gt dependant control can lead to savings of up Reliabil ity EN 15232 to 5 yearly in compare to rooms without automatic control functions Design planning and installation documents A class solution are pre defined which makes the entire building process faster and more reliable User documents and descriptions are prepared to assist in user training The gt Future proof application works as an individual stand alone room control unit or combined with the The application is prepared and defined for entire network integrati
7. push button 1 1 8 Room 001 Light Permanent OFF 0 Permanent OFF movement detector disabled 1 1 9 Room 001 Light Feedb operation Indication permanent off 0 and mode automatic regulation 1 2 1 Room 001 Heating control value Heating 0 100 sent by the room temperature controller to the EMO valve drive heating 2 1 2 Room 001 Cooling control value Cooling 0 100 sent by the room temperature controller to the EMO valve drive cooling 2 1 3 Room 001 Comfort Standby mode Change between comfort 1 and standby 0 mode 2 1 4 Room 001 Window contact Window open 1 gt frost heat protection Application 8 3 0 0 0 4 ly Movement dependent automatic light control with light regulation and manual control temperature control heating and cooling with KNX EMO valve drive single room Technical specifications Actual value correction The measured brightness value actual value can be corrected A distinction is drawn here between the installati on location of the presence detector and the reference area a desk surface for example The brightness value of the reference area is determined with the aid of actual value correction and taking the brightness value measured by the presence detector at the installation location and an internal adjustment curve into account In the case of light regulation it is not the brightness value at the installation location which is important but the brightness value at the referenc
8. specifications Components Application consists of one presence detector one temperature controller with buttons one DIN rail 0 10V control unit mounted in the cabinet or close to the room and KNX EMO valve drives MTN647091 KNX Control Unit 0 10V REG K 1 gang with manual mode fanetone MTN630919 KNX ARGUS Presence with light control and IR receiver MTN639118 KNX EMO valve drive with 2 binary inputs here for heating purposes MTN639118 KNX EMO valve drive with 2 binary inputs here for cooling purposes Design ranges Frames not included Other designs and colours available EXXACT WDE002939 KNX PB 2 gang with room temperature control unit Installation The presence detector is intended for ceiling mounting in a size 60 mounting box It can also be mounted to ceilings using the surface mounting housing for ARGUS Presence art no MTN550619 Application 8 3 0 0 0 4 ly Movement dependent automatic light control with light regulation and manual control temperature control heating and cooling with KNX EMO valve drive single room Technical specifications Wiring diagram KNX KNX Push button 2 gang ARGUS Presence with room temperature with light control control unit and IR receiver WDE002939 MTN630919 System component Lighting control Temperature control Temperature control Presence detection a KNX KNX _ Power
9. supply Control unit 0 10 V EMO valve drive EMO valve drive REG K 1 gang _ MTN639118 MTN639118 with manual mode here for heating here for cooling a purposes a purposes L N Window contacts binary input 1 things work together Application 8 3 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control heating and cooling with KNX EMO valve drive single room Technical specifications Note Number of controlled electronic interfaces highly depends on used ones check with manufacturer recommenda tions An electronic interface takes high inrush current It is recommended that Type C MCB s Miniature Circuit Breaker s are used Using Type B leads to decreased number of units If window contact is not used green and yellow wire has to be tied together shortcircuit settings Configuration The ETS tool is used to set the parameters for the devices in the application and to define the functional relationship between the devices by group addresses The following parameters and group address relations must be set and assigned The parameters should be set first and in the described order The parameters which can be changed to fine tune the application are described further on KNX Argus presence with light control KNX Push button 2 gang with RTC 12 Sw
10. SeeTool Solutions for KNX Office building segment Application 8 3 0 0 0 4 Movement dependent automatic light control with light regulation and manual control temperature control heating and cooling with KNX EMO valve drive single room Schneider Application 8 3 0 0 0 4 FLN Movement dependent automatic light control with light regulation and manual control temperature control heating and cooling with KNX EMO valve drive single room Lighting and temperature control functions The lights are automatically switched ON or OFF dependant on people s movement and existing brightness When the lights are on the light controller in the presence detector maintains the decided lux set point by dimming the lamp actuator dependant on the available daylight In addition three predefined light levels and a permanent OFF can be activated manually by push button Temperature controller tries to keep room temperature at it s setpoint by controlling KNX EMO valve drives for heating and cooling The movement detection will automatically set the temperature control either into comfort or standby mode A connected window contact will set the temperature control into frost heat protection mode when the window is open Application areas Lighting The application is defined to be used in office rooms and or conference rooms where the level of light will be kept constant taking into account the amount of natural light The solution
11. automatic light control with light regulation and manual control temperature control heating and cooling with KNX EMO valve drive single room Technical specifications Fine tuning Some parameters can be changed to fine tune the solution to the building and specific requirements Parameter which may need to be adjusted are listed below our recommendation in brackets KNX ARGUS presence detector with light control and IR receiver The staircase timer delay time will be retriggered by every detected movement when the light is on The light will be dimmed down to minimum if no movement has been detected within the specified time If no movement is detected the light will stay on minimum level for a time period specified by the parameter dimming down time After this time the light will be switched off Parameter page Parameter Value General light control gt Control response in automatic mode gt Times Time base for staircase timer 1s 1 min 1h 1 min General light control gt Control response in automatic mode gt Times Time factor for staircase timer 1 255 25 General light control gt Switching off in automatic mode Time base dimming down time 1 s 1 min 1 h 1 min General light control gt Time factor dimming down time 1 255 5 Switching off in automatic mode Delay time Time base x Time factor Dimming down time Time base x Time factor Lux
12. dead time Then a staircase timer is started which will be retriggered by every detected movement If no movement is detected the staircase timer will run out and standby mode is activated again Parameter page Parameter Value Block 2 general gt Dead time Time base 1s 1 min 1 min Movement sensors Block 2 general gt 1 255 3 Movement sensors Dead time Time factor Block 2 general gt Time base for staircase timer 1s 1 min 1h 1 min Times Block 2 general gt Time factor for staircase timer 1 255 25 Times KNX Push button 2 gang with room temperature control unit Push buttons The end user can select brightness level lux value with push button 1 2 and 3 These values can be changed with the parameters of the push buttons Parameter page Parameter Value Push button 1 edges Value 1 basis factor 500 lux values Basis 0 01 327 68 0 32 Push button 1 edges Factor 0 2047 1562 values Push button 2 edges Value 1 basis factor 300 lux values Basis 0 01 327 68 0 16 Push button 2 edges Factor 0 2047 1875 values Push button 3 edges Value 1 basis factor 100 lux values Basis 0 01 327 68 0 08 Push button 3 edges Factor 0 2047 1250 values Note Temperature controller parameter pages uses the unit Kelvin s K for relative temperatures and Cel sius C degrees for absolute temperatures 1K 1
13. e area desk For actual value correction you will need a luxmeter example Roline TES 1335 or equivalent Four measurements are required for actual value correction setti ngs e With the artificial lighting switched OFF brightness is measured at the presence detector installation location e With the artificial lighting switched OFF brightness is measured at the reference area desk for example e With the artificial lighting switched ON maximum brightness brightness is measured at the presence detector installation location e With the artificial lighting switched ON maximum brightness brightness is measured at the reference area desk for example The measurements can be done in daylight but not in clear sunshine best condition is cloudy weather To switch ON to maximum brightness a value telegram 100 can be sent from ETS to the value object of the control unit for example Note the presence detector should not be in operation at this time The four lux values measured must be entered as parameters in ETS Parameter page Parameter Value General Actual value installation site Lamp 0 2000 lux switched OFF General Actual value installation site Max 0 2000 lux brightness of lamp 100 General Actual value reference surface Lamp 0 2000 lux switched OFF General Actual value reference surface Max 0 2000 lux brightness of lamp 100 Application 8 3 0 0 0 4 Movement dependent
14. itch object1 Block 2 1 bit gt 2 1 3 0 ObjectA PB 1 2 byte gt 1 1 7 60 Switch output Closed loop 1 bit gt 3 Object A PB 2 2 byte gt 1 1 7 61 Dimming output Closed loop 4 bit gt 1 1 2 6 Object A PBS 2 byte gt 1 1 7 62 Setpoint 1 Closed loop 1 byte gt 1 1 3 9 Value objectA PB 4 1 byte gt 1 1 8 64 Fb operat mode Closed loop 1 bit gt 1 1 9 11 Status feedb ject PB 4 1 bit 1 1 9 70 Value input Closed loop 1 byte lt 1 1 8 gbiSs l i F 45 Frost heat 71 Lux value setting Closed loop 2 byte lt 1 1 7 protection input Control 4 bit lt 2 1 4 107 Result act value Send 2 byte gt 1 1 6 47 Comfort input Control 1 bit lt 2 1 3 optional 62 Correcting 109 Status feedback Safety pause 1 bit lt 1 1 4 variable heating 110 Status feedback Brightness 1 byte lt 1 1 5 basic level Control 1 byte gt 2 1 14 General 65 Correcting Actual value correction enable variable cooling Actual value 0 2000 Lux installation site basic level Control 1 byte gt 2 1 2 ae isis a Push button 1 A ma sae 9 ee i nT Select push button ctual val ue 0 2000 Lux reference surface o Edges with 2 byte Lamp switched off waities Max brightness of lamp Optional to check regulation after download Push button 1 edges values Send actual value cyclically Value 1 basis factor 500 reference surface enable Basis possible Time base send lux value 1s values in brackets 0 32 0 to 655 04 Time factor send lux value
15. ng setti n g S Times Object A 1 byte in steps 0 100 Time base for staircase timer 1 min Value 0 Time factor for staircase timer 25 Trigger status LED Flashes when status 3 feedback object General light control gt equals 1 Control response in automatic mode gt Brightness Control general Nominal value 10 2000 Lux Use control Yes reference surface 500 Controller type Heating and cooling Hysteresis 10 50 20 Duration of comfort extension None General light control gt tpoint adjustment Switching off in automatic mode Sateo echsa maintained after Time base dimming down time 1 min E h i Ye Time factor dimming down time 5 change M oper Mode Nes Control general gt Actual temperature resultant KNX Control unit 0 10V REG K 1 gang Correct internal actual temperature 1 1 14 gt 0 Switch object Channel1 41 bit Tow 12 Ta ee o NOTE See description fine tuning 1 1 2 gt 1 Dimming object Channel 1 4 bit Control general gt Control heating 1 1 33 gt 2 Value object Channel 1 1 byte Select heating system Adjustment via control parameter Ves Sa eael GEA AHi Proportional range for sue 2ng heating in 0 1 K 10 255 40 1 1 5 lt 9 Status feedb Reset time for heating 1 255 min 20 value Channel 1 1 byte Control general gt Control cooling NOTE To rates R muet kosci Select cooling system Adjustment via 1 General control parameter
16. on into a Building Management tested amp System if required through the open technology communication network va idated Application 8 3 0 0 0 4 ly Movement dependent automatic light control with light regulation and manual control temperature control heating and cooling with KNX EMO valve drive single room Technical specifications Functions Lighting control The lights are automatically switched ON when a person enters the room and the brightness value is below the selected brightness threshold If no movement is detected within a delay time of 25 minutes the light will be dimmed down to minimum If no movement is detected for another 5 minutes the light will be switched off e functions When the lights are on the light controller in the presence detector maintains the decided lux set point by sending dimming telegrams to the lamp actuator If the daylight will increase the regulation dims down the artificial light If it decreases the regulation will dim up the artificial light The lux set point after download and power failure is adjustable by ETS software The default lux setpoint at the reference surface e g desk is 500 lux 20 hysteresis The user can also select the lux setpoint by the push button unit Button 1 will give high brightness 500 lux button 2 will give medium brightness 300 lux and button 3 low brightness 100 lux With button 4 permanent OFF can be activated The light will then be off
17. page Parameter Value Control general gt Actual Correct internal actual temperature 0 temperature resultant factor 128 127 0 1 K Parameters for tuning heating control Xp and Ti Parameter page Parameter Value Control general gt Control Proportional range for heating in 0 1K 10 255 40 1 255 min 20 Parameter page Parameters for tuning cooling control Xp and Ti Parameter Value Control general gt Control cooling Proportional range for cooling in 0 1K 10 255 40 Control general gt Control cooling Reset time for cooling in min 1 255 min 20 Power failure behaviour Behaviour when bus voltage fails relay no Light is OFF Behaviour when bus voltage returns switch off relay Light is OFF JAN fine tuning 11 Application 8 3 0 0 0 4 ly Movement dependent automatic light control with light regulation and manual control temperature control heating and cooling with KNX EMO valve drive single room Technical specifications User manual The user manual provided for the application is an end users training material and can be installed at site when final submission is made Please do no forget to cut out this quick guide for the user and attach to the wall next to the entrance to the room Also make sure the customer is aware of the installed applications function Quick guid This room is equipped with a move ment dependent automatic light con
18. trol with light regulation and manual control temperature control Automatic mode operation Lighting control The lights are automatically switched ON when a person enters the room and the brightness value is below the selected brightness threshold If no movement is detected within a delay time of 25 minutes the light will be dimmed down to minimum If no move ment is detected for another 5 minutes the light will be switched off When the lights are on the light controller in the presence detector maintains the decided lux set point by sending dimming telegrams to the lamp actuator If the daylight will increase the regulation dims down the artificial light If it decreases the regulation will dim up the artificial light Manual mode operation The user can also select the lux set point by the pushbutton unit Button 1 will give high brightness 500 lux button 2 will give medium brightness 300 lux and button 3 low brightness 100 lux With button 4 permanent OFF can be activated The light will then be off until one of the other buttons is pressed When permanent OFF is activated the status LED next to the button is blinking service Schneider foryour 06 10 Application 8 3 0 0 0 4 amp Electric cu st omer 12 Application 8 3 0 0 0 4 ly Movement dependent automatic light control with light regulation and manual control temperature control heating and cooling with KNX EMO valve drive
19. until one of the other buttons is pressed When permanent OFF is activated the status LED next to the button is blinking Temperature control Temperature controller tries to keep room temperature at it s setpoint by controlling valves Heating and Cooling is controlled by a KNX EMO valve drive each Movement detection will automatically set the temperature control into comfort mode To save energy this will not happen until a person has been in the room for more than 3 minutes In this way the temperature control is not affected if someone is present in the room just for a short period of time If no movement is detected within a delay time of 25 minutes the temperature control is set into standby mode If a window contact breaking contact is connected to the EMO valve drive heating the temperature control will be set into frost heat protection mode when the window is open Comfort mode default room temperature setpoint heating 21 C cooling 24 C Standby mode default room temperature setpoint heating 19 C cooling 26 C Frost Heat protection heating 7 C cooling 35 C The setpoint can be adjusted by the user 3 C from given setpoint This is done by pushing invisible buttons on both sides of the display frame Application 8 3 0 0 0 4 ly Movement dependent automatic light control with light regulation and manual control temperature control heating and cooling with KNX EMO valve drive single room Technical
Download Pdf Manuals
Related Search