Home
Easy RGB(Y)
Contents
1. in order to avoid chaos of working units after a long time one of the receivers is needed to be set as Master the Master will launch synchronized signal when color is changing thus ensure this group of receivers are in good order no matter how long the color is changing 5 5 Color changes of multiple different ID receivers in the same mode In order to avoid chaotic phenomena after a long time when multiple different ID receivers are changing the color under the same mode one MASTER receiver is needed to be set in this group How to set MASTER receiver and SLAVE receiver please refer to 4 2 Receive learning ID code Notice Only onemaster receiver can be set among a group of receivers otherwise it may cause chaotic phenomena the Master will launch synchronized signal when colour is changing to ensure this group of receivers will be in good order no matter how long the color changes For example Receiver 1 2 3 4 5 move color under the same mode 1 at this time you need to set one of the receivers as Master receiver if receiver lis setas MASTER then receiver will launch synchronized signal to other receivers 2 3 4 5 meantime they will keep changing constantly without chaos according to the synchronized signal from receiver 1 In addition if there are several receiver 1 only one of them can be set as MASTER receiver others must be set as SLAVE receiver otherwise it will cause chaos 5 3 The usage of button M the switch between Sy
2. Current 4CHx3A max SR 1003RC 4CHx350mA SR 1012RC 4CHx700mA SR 1022RC Output power 4CHx 36 108W max SR 1003RC 4CHx 4 2 12 6W SR 1012RC 4CHx8 4 25 2W SR 1022RC Working Frequency 434MHZ 868MHZ 915MHZ optional 3 components description 3 1 Sender model SR 2806 O R button and indicator E G button and indicator e B button and indicator os O Y button and indicator 8 Working status indicator the sender 1s in dormant status when the indicator is off The sender is under working when the indicator 1s flashing rapidly If the indicator continues flashing at the frequency of second it indicates that the sender batteries low and needs to replace new batteries Slow down the speed when color is changing Speed up when color is changing Multifunction button used for selecting Synchronous or asynchronous A O Brightness down Brightness up Multifunction button used for tura ON OFF and white output e D Figure 1 10 is for selecting receiver s ID and ID itself to turn ON OFF Touch wheel for selecting R G B colors 3 2 Receiver Model 1003RC SR 1012RC SR 1022RC B Da Molly J1 power input socket red SEC green blue SDS SA AH yellow J2 RGB Y output socket es e j3 RGB RGBY output switch closed circuit is RGB 3 channel output open circuit i is RGBY 4 channel output Receiver ID code l
3. Easy RGB Y Remote controller User Manual 1 Product introduction Easy RGB Y remote controller is a wireless color control system that consists a sender and a receiver or several receivers as shown in Figure 1 2 By selecting switch status you can set the system as RGB 3 channel output or RGBY 4 channel output Using Easy RGB Y remote controller you can get whatever color you want you can choose any color from RGB Y to adjust so as to mix more than 100 million kinds of colors With built in 10 kinds of color changing modes you can easily switch color changing modes and adjust speed and brightness Function Pause enables RGBY LED to stay at your favorite color under the situation of color changing modes which operation is simple but functional Three working frequencies are available 434MHZ 868MHZ or 915MHZ which are suitable for Europe Americas and elsewhere in the world All products completely comply with European CE regulations and American FCC regulations Sender Fig 1 OOO ASIA usa nj MmMojad 235 boo T E T E A ee A Receiver Fig 2 2 Performance parameters 2 1Sender model SR 2806 Working temepature 4 5V 3x1 5V 7 AAA battery Working current lt 22mA Dormancy current lt 20uA Working frequency 434MHZ 868MHZ 915MHZ optional Transmit power gt 5dBm 2 2 Receiver model SR 1003RC SR 1012RC SR 1022RC model Input Voltage 12 36VDC Output Voltage 12 36VDC Input
4. can turn on Off the corresponding single receiver E g If you need to turn off receiver 1 press button Q more than 2 seconds if you need turn it on again please press button again for more than 2 seconds Notice If you turn off the extension by pressing the corresponding number button you must turn on this receiver in the same way The receiver can not be switched on through button ON OFF 6 Symptoms and solutions The Receiver 1 Exceed learning 1 Press receiver learning cannot be learned time every learning button LED indicator is to the sender time 1s 5Seconds ON press the number only button before led indicator 2 Sender is under is OFF then press dormancy status function button or touch color wheel Press On Off to make the sender under working Status The sender Receiver isn t To learn the receiver by cannot control learned to the the sender the receiver sender When receiver is learned The receiver isn t to the sender press learned to the number button first then sender correctly press function button or Remote distance is touch color wheel out of range Shorten the remote Incorrect receiver distance Choose correct receiver ID Color changing MASTER receiver Reset anew MASTER isn t isn t set receiver synchronized More than two Relearn all the receivers MASTER receivers with one MASTR receiver are Set Wrong color 1 Wrong connection 1 Recon
5. e the color through R G B Y buttons e a es a E O For example you choose a color by touching color wheel O still want add a bit more brightness to red color just S press R button Q then the indicator of R will be on and red is selected make clockwise Ce on the color o by figure then the brightness of red will be increased If you want the red color to be darker just make counter clockwise O on the color O If need to adjust the color brighter or dim several colors at same time also just choose the colors such as R G then make clockwise rotation O counterclockwise O it can simultaneously adjust the brightness for both colors If you want to cancel the selected color just press selected button the corresponding color will be off this color is abandoned a a a o By pressing of R G B Y button E E E you can turn on off the corresponding color For example under a certain mode turn off the red color press R E for 2 seconds then the red color will be turn off If you want to turn on red again press R E for another 2 seconds the red will be on again The same operation for other colors In short using R G B Y buttons E E O and operating color o you can mix more than 100 million colors or any color you want Attention The receiver 1s under single or multi color adjustment condition when any single or multi color is selected Under this condition you can onl
6. earning Button Receiver ID code learning indicator and for receiving message 4 Basic Usage 4 1 Install battery Initial using easy RGB Y remote controller open the battery cover on the back of the sender load 3pcs 7 AAA 1 5V batteries Please pay attention to the battery s negative and positive otherwise it will fail to work 5 4 2 Receiver learning ID Initial using easy RGB Y remote controller must learn the ID of the receiver the purpose of learning ID code is to make a certain receiver which can correspond the sender The method of Receiver learning ID is as follows press the ID learning og e button o on the sender the ID learning indicator IS On then press one of the number button O O O O onthe sender press the number that you want this receiver to be E g If you want this receiver to be No 1 please press button O first then touch the O or you can press any functional button on the sender such as E E E E ON to transmit signal to the Sender after Receiver receives the signal from the sender the indicator will flash a few times and then turns off then receiver ID 1s activated If the ID activation 1s failed at the first time please repeat the previous procedures Attention The receiver ID learned by touching color wheel G is different from reciever that learned b ressin unction button 0 E The receiver ID learned by touching color wheel O we define it as SLAVE rec
7. eiver the receiver ID learned by pressing function button E E Ok we define it as MASTER receiver The purpose of learning these two kinds of receivers is to ensure the receivers and color changing synchronously to avoid the color changing out of order This point will be noted later 4 3 Delete ID and ID re learning If you need to delete the ID learned in the receiver press ID learning button o for more than 5 seconds when learning indicator 1s off then the learned ID is deleted If you need the receiver learn a new ID repeat the operation of 4 2 Receiver learning ID 4 4 Choose color by touching color wheel After the receiver learned the ID you can change each receiver s color by touching color wheel If you want to change the color of receiver NO 1 Press button then make rotating touch on color wheel O your figures at this time the color of receiver No 1 will be changed constantly when your favorite color appears stop rotating and leave the color wheel If you need change color of several receivers at the same just choose a number for these several receivers first then touch color O For example change color for receivers NO 1 2 3 4 5 6 at the same time you need press number to 6 butto O first then touch the color O a a 4 5 Change color by R G B Y button O Q E O In addition to change the color by touching color o but you can also chang
8. nchronous color changing and asynchronous color changing Press sam for 2 seconds to switch between Synchronous color move and Asynchronous color changing when multiple different receivers are in the same mode Synchronous color changing means the starting point and ending point are at the same time Asynchronous color changing means there 1s certain time delay of the starting point and ending point the later receiver start or ending point is always later than the previous receiver For example Receiver 1 2 3 4 5 changing together under mode 1 if it is Synchronous color changing all of the receivers change will start and end at the same time If it 1s Asynchronous color changing then receiver will start change firstly then follows by receiver 2 and later by receiver 3 and receiver 4 and receiver 5 and recycle to receiver The purpose of asynchronous color change is to achieve the color changing effect which looks like water chasing 5 4 Usage of ON OFF 2 5 4 1 Press of ON OFF button 2 for turning ON OFF receiver 5 4 2 Press ON OFF MO for more than 2 seconds it can reveal white light output each channel is 100 output 0000 5 5 The usage of number button O O 5 5 1 Press on number button for choosing the corresponding receiver E g to adjust the brightness of receiver 1 you need to press 1 button O then press sutton O or MO to adjust its brightness 5 5 2 Pressing number button
9. nect RGB Y of RGB Y electric electric wires wires LED flashing 1 the power is not 1 Change a higher power enough supply 7 Precautions 7 1 Please unload the batteries if the send is not used for a long time 15 T2 7 3 1 4 Don t fall the sender from a high place or don t squeeze it Please replace new batteries if there is a warning indicator of insufficient power otherwise it would cause damage to the sender Receiver 1s non waterproof not for outdoor use
10. vels the minimum is 10 and 10 the maximum is 100 4 8 Changing speed adjustment Under color changing mode you can slow down the changing speed by pressing ston O or speed up changing speed by pressing button E 16 speed levels in total are available The maximum changing cycle is 4 seconds the minimum changing cycle is 256 seconds 5 Expanded Usage 5 1 Color changing for multiple same ID receivers under same mode One receiver of the sender can be learned unrestricted by multiple receivers a receiver can be only defined one ID No from one sender If one of senders is learned by several receivers all these receivers will share the same ID No When all these receivers are changing color at the same time to ensure long time changing in order one of the receivers from this groups 1s needed to be set as Master receiver and other receivers need to be set as Slave receivers How to set Master receiver and Slave receiver please refer to 4 2 Receiver learning ID code Notice Only one receiver Master can be set amont a group of receivers otherwise it may cause chaotic phenomena When Master receiver is set this group receivers are changing color at same time synchronized signal will be emited so as to ensure this group receiver will be in order no matter how long the color changes and keep changing 11 forever For example 10 receivers are learned to be ID 1 these 10 receivers will change according to one mode
11. y make clockwise rotation O or counterclockwise O a to adjust the color A direct touch on color O not work Only after exiting from the single or multi color condition a direct touch on color wheel O work 4 6 Choose color changing mode Selecting the mode EO receiver change colors according to different modes a total of 10 built in color changing modes If you want one or several receivers under color changing mode press 9 0000 number button O and choose receiver number then press button O For first press of o O receiver will change according to mode 1 one more time press of NO the receiver will be paused it will stay at one color under mode 1 condition Press ENO again the color will change according to mode 2 press button ON more time it will be paused at one color under mode 2 Press ENO for seconds the receiver will keep changing as follows MODE1 STOP MODE2 STOP MODE3 STOP MODE4 STOP MODE5 STOP MODE6 STOP MODE7 STOP MODE8 STO P MODE9 STOP MODE 10 OFF MODE1 The receiver will be at one of static colors by touching the color wheel in color changing modes Then press M button again receiver will be changed as Mode 1 again 4 7 Brightness adjustment Under the static color status or color changing status you can adjust the brightness by press B E pressing button E to increase the brightness The brightness is divided into 8 le
Download Pdf Manuals
Related Search
Related Contents
Care & Use Manual Gigabyte GA-EX58-UD4 motherboard HP Notebook Hard Drives & Solid State Drives Identifying 6205 Bathymetry and Side Scan Sonar User Hardware カタログ Jensen JXMC User's Manual QNAP TS-439Pro/2TB Copyright © All rights reserved.
Failed to retrieve file