CCTV CONTROL KEYBOARD
Contents
1. CCTV CONTROL KEYBOARD Contents Features Specification Front and Back Panel Description System Installation Operation Simple Operational Reference Table Accessory 14 15 2004 09 13 Ver 1 1 P N 040075 E Features Q Support CCTV system control Q Control Dome Camera and P T Z Receivers with RS 485 Interface QO Supports up to a total of 127 devices 127 Dome Camera or P T Z Receiver The 3 axis joystick supports Pan Tilt control and Auto Focus function Specification Power DC 12V Power Consumption 2W Control signal RS 485 Standard 9600 Baud Rate Control Device 127 Devices Manual pal Right Left Pan Tilt Control au wl il ne Pan On Off Sequence On Off ZOOM Tele Wide Lens Control FOCUS Near Far Auto BRIGHTNESS Gamea Cnoi Preset Point pee Camera Setup Available Dimension 296x190 4x52 7mm WxDxH O P Temperature 0 45 C Weight 1 4 Kg Symbol Description 1 Function keys are shown by framed capital boldface print letters Example ENTER AUTO FOCUS etc 2 Function key indicates the order sequence Example 2 8 ENTER meaning press the function key 4 DEVICE 001 _ 12 8 and then ENTER indicate messages from the device and is shown on the control keyboard LCD display 4 n indicates the ID number of the nth2. TO FOCUS LED OFF Auto Focus AUTO FOCUS AUTO FOCUS LED ON Speed By Zoom SPEED BY ZOOM SPEED BY ZOOM LED ON Brightness Control BRIGHTNESS or BRIGHTNESS Chose to Select the Preset Points No Key GO PRESET 128 Preset Points Start up the Preset Mode No Key Group No AUTO PAN AUTO PAN LED ON Stop the Preset Mode AUTO PAN or Push the joystick AUTO PAN LED OFF Disable the Alarm EVENT RESET EVENT RESET LED OFF Relay Switch RELAY1 RELAY2 RELAYS LED light ON meaning LED ON and vise versa 14 E Accessories 1 Power Adaptor DC 12V 2 User s Manual 15
3. The buzzer does not dismiss automatically the user has to press the EVENT RESET key in order to stop the buzzer When the alarm of more than one device has been triggered continuously than the system select to lock on controlling the last device triggered by alarm event 12 When the alarm of the Speed Dome Camera has been triggered under Auto Pan ON mode the Speed Dome Camera will rotate in 300 per second to the preset correspondent point AUTO PAN Group When the alarm of more than one device has been triggered continuously than the system select to lock on controlling the last device triggered by alarm event When the alarm of the Speed Dome Camera has been triggered under Auto Pan OFF mode the Speed Dome Camera will rotate in 300 per second to the preset correspondent point AUTO PAN Group 13 Simple Operational Reference Table Functions Method of Operation Restart System Connection SYS RESET SYS RESET LED ON Upward rotation Push the joystick forward Downward rotation P T Z Control Push the joystick backward Leftward rotation Push the joystick leftward Rightward rotation Push the joystick rightward Select Dome Camera No Key ENTER or CH gt CH Lens Control ZOOM TELE or ZOOM WIDE Manual Control FOCUS FAR AUTO FOCUS LED OFF FOCUS NEAR AU
4. aning that the function has been disabled Please refer to P 8 gt About Auto Pan Mode When Auto Pan Mode has been started no other operations will function Unless when Auto Pan Mode has been disabled 11 Relay Control Three sets of relay control are provided RELAY1 RELAY2 and RELAYS when using P T Z Receiver gt Relay ON The RELAY1 LED lights up when RELAY1 key has been pressed That means RELAY1 is set ON and the output has been connected close status gt Relay OFF The RELAY1 LED will not light up when RELAY1 key has been pressed That means RELAY1 is set OFF and the output has been disconnected open status Alarm Management gt Alarm Input The Speed Dome Camera is equipped with six alarm input connectors Alarm 1 Alarm 6 corresponds to both preset points and AUTO PAN Group Once the alarm signal is detected the Speed Dome Camera will automatically move to the preset point or Start up AUTO PAN gt Alarm Management of P T Z Receiver or devices please refer to the relevant guide gt Alarm Mode Management The Speed Dome Camera is set to lock on the last alarm input Thus once the alarm signal is detected the Speed Dome Camera will automatically move to the preset point or Start up AUTO PAN triggering the alarm to buzz EVENT RESET LED will be lighted and the LCD will display DEVICE XXX ALARM INPUT detected informing the user that an alarm event has been
5. device ID numbers ranges from 001 127 Front and Back Panel Descri ption gt Front Panel OBOeQqg eAa2QAaQqQqQA OAC wd EY SS LI O EVENT RESET System Reset ESC ENTER and Number Key Lens Control Key Device Select Key Joystick LCD Panel OSD Function Key OSD LCD Function Keys a SET il PRESET i DOME SELECT ZOOM FOCUS FAR BRIGHTNESS Preset Key Preset setup or run preset position Auto Key Auto Pan and Auto Focus Speed By Zoom Key Auto speed adjustment with multiple zoom function External Relay Control Key gt Back Panel TN IOo a AAEN kr A D 2 3 Power in connector DC 12V o o o 2 RS 485 connector D D D D RS 485 RJ 11 connector Pin No Definition D O a R O rmM System Installation p os wo g SENSOR J a Me _ j i E i SPEED DOME 7 SPEED DOME i m sf ALARM A SENSOR IN p Receiver fy SENSOR ALARM ALARM 1 IN OUTPUT OUTPUT OUTPUT PTIZRECEIVER 1 RSS 4 I vhrttoteh trrerres KEYBOARD Fig 1 1 The system supports connections of numerous Speed Dome Cameras or P T Z Receivers assigning a set ID Note ID numbers ranges from 1 127 and may not be repeated
6. device moves leftward or rightward gt Zoom Speed Setup The LED lights up after pressing SPEED BY ZOOM key Then the Pan Tilt movement of the Dome will be proportional to each ratio Movement slows down when zooming Device Select Key gt Use the number key ENTER key Pre select the desired nth device by pressing the number and ENTER Key on the controller keyboard Then the LCD will display ID of the device gt Use the DOME SELECT KEY function of control keyboard DOME SELECT Key DOME SELECT CH the system automatically selects for the ID number larger than the present ID number the system automatically selects for the ID number smaller than the present ID number DOME SELECT CH After completing the change the LCD will reflect the selected device ID and when the action was failed or the selected device did not exist no changes will be shown by the LCD it remains as original status Zoom Control This item allows you to change the zoom ration from OFF to 220X 22 times optical magnify gt Lens Control Zoom TELE Press ZOOM TELE key to narrow the angle of viewing and release the key to stop zooming gt Lens Control Zoom WIDE Press ZOOM WIDE key to widen the angle of viewing and release the key to stop zooming Focus Control Focus Control may be done by AUTO or manually by the user gt Manual Control Focus Far Pre
7. for setup and control through control keyboard Ref Fig 1 1 gt Connecting RS 485 Connect RS 485 terminal D from the control keyboard to terminal D of RS 485 DATA IN connector from the device then connect RS 485 terminal D the same set of terminal to the terminal D of RS 485 DATA IN connector from the device Operation SYSTEM CONTROLLER Oo Oo oa o OSD MENU GO AUTO SPEED SYS RESET D a g g DOME SELECT Ls ZOOM CH TELE FOCUS L 5 NEAR LE BRIGHTNESS System Reset After connecting all necessary cables startup the system linking by pressing SYS RESET key The LCD displays the following message SYSTEM oe the LED starts flashing Press SYS RESET key again the system linking will start search the system connection device and make sure that all the connected devices are probably linked f DEVICE XXX LOST When the LCD displays the following message yi PRESS SYS RESET means that an error has been occurred Please press SYS RESET key after checking and sorting the circuit Manual Control Up Down Left Right Speed Speed Dome Cameras or P T Z Receivers may be controlled manually by using the joystick Up Down Left Right Speed gt Joystick The movement depends on the angel of the joystick Push the joystick up or down the device will move forward or backward Push the joystick left or right the
8. mber 1 128 and press SET PRESET key the LCD will he eee eee then press again SET PRESET key cispay T meaning that the setup has and when the display show seen l been completed Repeat the steps 1 4 again to set more preset points 10 Call upon the Preset Points When the setup of the preset point has been completed it may be called upon gt Enter the assigned preset number and press GO PRESET key the LCD li PRESET aa will display and the Speed Dome will move to that specific preset point Example 1 preset point 1 GO PRESET 128 preset point 1 2 8 GO PRESET Change the Preset Point To change the preset point use the joystick to move the cursor to the preset point setup selection and change to your desired settings AUTO PAN The function has numerous groups every group has numerous setting points and you have to decide the pan direction and the pan speed for each point gt Start up Auto Pan Mode Under Control Mode assume device 1 when the LCD displays DEVICE 001 z key in the group number to be setup Assume group 1 then enter 1 then press AUTO PAN key the LED of the AUTO DEVICE 001 AUTOPAN GROUP 1 PAN lights up LCD displays meaning that the setup has been completed gt Stop Auto Pan Mode Press AUTO PAN key or move joystick the LED of the AUTO PAN goes off me
9. ss FOCUS FAR key to focus far and release the key to stop focusing gt Manual Control Focus Near Press FOCUS NEAR key to focus near and release the key to stop focusing gt Auto Focus Control Press AUTO FOCUS key or the joystick the LED of the AUTO FOCUS lights up and press AUTO FOCUS key again to disable the function FOCUS FAR and FOCUS NEAR will not function when AUTO FOCUS function has been started Setting the Preset Points Setting the preset point enables the Speed Dome Camera to have preset points from 1 128 You may key in a number 1 128 and press SET PRESET key to store current position as preset You may also key in a number and run the preset point that you ve just stored Selecting a Soeed Dome Camera Press 1 key and the ENTER key the LCD will display DEVICE 001 _ it means that Soeed Dome number 1 has been selected Example Select the 1 Speed dome Camera 1 ENTER Select the 127 Speed dome Camera 1 2 7 HENTER Controlling the Joystick The joystick may move the Speed Dome to that specific location Controlling the zoom ratio from 1X to 220X 22 times optical It is suggested when setting the preset points to manually adjust the iris to enable clarity and stability of the focal distance Key in a nu
Download Pdf Manuals
Related Search