TR118 R4 op
Contents
1. operates independently of the timing channels Whenever the clock button is pressed the time of day will appear in the display If timers are operating respective T1 or T2 will flash in display 12 24 HOUR FORMAT SELECTION 1 To activate 24 hour format in Clock Mode hold START STOP button down for approximately 3 seconds beep tone will indicate format change 2 To change back to 12 hour format repeat stop 1 above COUNT DOWN TIMER SETTING SEE FIG 1 1 Press either T1 or T2 button for desired timing channel The selected channel T1 or T2 will appear in the display The colon does not flash in the timer mode 2 Press CLEAR to reset timer to zero 3 Press individual HOUR MIN amp SEC buttons to program desired time The numbers can be fast forwarded by holding the individual buttons down for 2 seconds 4 If error is made in programming hold individual HOUR MIN amp SEC button down first then press the clear button to zero the digit Then reprogram as explained above 5 Follow the same procedure above for programming the other timer channel TIMER START STOP 1 After time setting is ready press START STOP button once to activate timer Steady T1 or T2 indicator on screen shows active channel on display 2 When timer is counting press START STOP button once and displayed timer channel will pause 3 Press START STOP button once and timer will resume counting 4 Both timing channels can be used at the s2. 1 second resolution 4 Press START STOP to stop count up timer 5 If you wish to restart timing process press START STOP button again 6 To turn timer off press START STOP button and then Clear button 7 If count up stopwatch timer is not turned off when it reaches 99 hours 59 minutes 59 seconds it will start counting over again at 1 second resolution from 00H 00M 00S BATTERY REPLACEMENT To replace exhausted battery slide push the battery cover on back side in direction of arrow Set cover aside and remove battery Insert a now 1 5V AAA battery as indicated by the polarity symbols amp marked and close battery cover Sometimes the timer may not activate after installing a new battery If this happens simply remove battery from the battery compartment and reinstall again The Clock will resume normal operation CLIP ATTACHMENT The timer can clip on thin board belt or shirt pocket using the plastic clip on the backside of timer MAGNETIC ATTACHMENT The timer can attach to iron or steel surface using the magnet attached to clip on backside of timer TABLE TOP USE Use the clip and metal stand bar together to stand clock timer at an angle on any flat surface PRECAUTION When handled properly this unit is engineered to give you years of satisfactory service Here are a few product care instructions 1 Do not immerse the unit in water If the unit comes in contact with water dry it immediat
3. 2 CHANNEL JUMBO DISPLAY CLOCK TIMER MODEL TR118 USER S MANUAL TIMER FEATURES 1 2 Channel LCD Count down and Count up Timer together with Clock 2 6 digits display showing HOUR MINUTE and SECOND for both Timers and Clock 3 Automatic count up after Timer counts down to zero 4 Count down timer Maximum setting is 99 hours 59 minutes and 59 seconds at 1 second resolution Count up timer Maximum count up range is 99 hours 59 minutes and 59 seconds at 1 second resolution 5 Buzzer alarm sounds for 1 minute when timer counts to zero 6 Timer memory recall for each count down timer 7 Individual buttons for HOUR MINUTE and SECOND setting NORMAL TIME SETTING 1 Press the Clock button down for approximately 3 seconds The digits and colon will flash in display 2 Press the Hour button to advance to the correct hour Hold button down for approximately 2 seconds for fast setting 3 A P will appear in the display below the colon for PM There is no symbol for AM indication 4 Press MIN button to advance to the correct minute Hold button down for approximately 2 seconds for fast setting 5 Press the SEC button to reset second digit to zero when the second digits are within the 00 29 second range pressing SEC button in 30 59 second range advances minute setting by 1 minute and resets second digits to zero 6 Press the Clock button to start clock The colon will flash in clock mode 7 The Clock
4. ame time When using both timer channels simply press the T1 or T2 button to note count down time remaining Non flashing T1 or T2 indicates the count down time of the channel being displayed TIMER BUZZER ALARM 1 When timer counts to 00H 00M and 00S timer buzzer alarm will sound and timer will begin to count up in seconds with respective non fleshing timer channel indicator appearing in display 2 Timer buzzer will be stopped by pressing any button 3 Buzzer will automatically turn off in 60 seconds Count up timer continues to operate until stopped 4 Count up timer in alarm mode can be stopped by pressing any button 5 Press Clear button to reset display to zero 6 If both channels are counting down when time expires in both channels within a minute of each other and the alarm has not been turned off the alarm for the just expired timer will sound with the other timer channel flashing in the display Turn off by pressing the START STOP button 7 The other channel alarm will sound at the completion of cycle and the indicator will count up 8 Press START STOP button to turn off TIMER MEMORY RECALL 1 After timer buzzer alarm stops press START STOP button once to recall preset timer time 2 Press START STOP button again to start timer COUNT UP STOPWATCH TIMER 1 Press desired timer channel button 2 Press CLEAR button to clear display 3 Press START STOP button and time will begin to count up in
5. ely with a soft lint free cloth 2 Do not clean the unit with alcohol containing detergent abrasive or corrosive materials Abrasive cleaning agents may scratch the plastic parts and corrode the electronic circuit 3 Do not subject the unit to excessive force shock dust temperature or humidity Such treatment may result in malfunction a shorter electronic life span damaged batteries or distorted parts 4 Do not tamper with the unit s internal components Doing so will terminate the unit s warranty and may cause damage The unit contains no user serviceable parts 5 Only use new batteries as specified in this instruction manual Do not mix new and old batteries as the old batteries may leak 6 Read this instruction manual thoroughly before operating the unit CAUTION The content of this manual and the product specifications are subject to change without further notice The technical specifications of this product are subject to change without notice Due to printing limitation the displays shown in this manual may differ from the actual display The contents of this manual may not be reproduced without the permission of the manufacturer MEMORY T1 T2 MAGNET PLASTIC CLIP BATTERY COVER ENGLISH 086 001626 17 MEMORY T1 T2
Download Pdf Manuals
Related Search